DS75176B,DS75176BT DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers Literature Number: SNLS381B DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers General Description Features The DS75176B is a high speed differential TRI-STATE (R) bus/line transceiver designed to meet the requirements of EIA standard RS485 with extended common mode range (+12V to -7V), for multipoint data transmission. In addition, it is compatible with RS-422. The driver and receiver outputs feature TRI-STATE capability, for the driver outputs over the entire common mode range of +12V to -7V. Bus contention or fault situations that cause excessive power dissipation within the device are handled by a thermal shutdown circuit, which forces the driver outputs into the high impedance state. n Meets EIA standard RS485 for multipoint bus transmission and is compatible with RS-422. n Small Outline (SO) Package option available for minimum board space. n 22 ns driver propagation delays. n Single +5V supply. n -7V to +12V bus common mode range permits 7V ground difference between devices on the bus. n Thermal shutdown protection. n High impedance to bus with driver in TRI-STATE or with power off, over the entire common mode range allows the unused devices on the bus to be powered down. n Pin out compatible with DS3695/A and SN75176A/B. n Combined impedance of a driver output and receiver input is less than one RS485 unit load, allowing up to 32 transceivers on the bus. n 70 mV typical receiver hysteresis. DC specifications are guaranteed over the 0 to 70C temperature and 4.75V to 5.25V supply voltage range. Connection and Logic Diagram 00875901 Top View Order Number DS75176BN, DS75176BTN, DS75176BM or DS75176BTM See NS Package Number N08E or M08A TRI-STATE (R) is a registered trademark of National Semiconductor Corp. (c) 2004 National Semiconductor Corporation DS008759 www.national.com DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers July 2004 DS75176B/DS75176BT Absolute Maximum Ratings (Note 1) ESD Rating (HBM) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage, VCC 7V Control Input Voltages 7V Driver Input Voltage 7V Driver Output Voltages +15V/ -10V Receiver Input Voltages (DS75176B) +15V/ -10V Receiver Output Voltage 500V Recommended Operating Conditions Min Supply Voltage, VCC Voltage at Any Bus Terminal +12 V (Separate or Common Mode) DS75176B Continuous Power Dissipation @ 25C DS75176BT 675 mW (Note 5) for N Package 900 mW (Note 4) Storage Temperature Range V -7 Operating Free Air Temperature TA 5.5V for M Package Max Units 4.75 5.25 0 +70 C -40 +85 C -12 +12 V Differential Input Voltage, VID (Note 6) -65C to +150C Lead Temperature (Soldering, 4 seconds) 260C Electrical Characteristics (Notes 2, 3) 0C TA 70C, 4.75V < VCC < 5.25V unless otherwise specified Symbol VOD1 Parameter Conditions Differential Driver Output Min Typ Max Units IO = 0 5 V Voltage (Unloaded) VOD2 Differential Driver Output (Figure 1) R = 50; (RS-422) (Note 7) Voltage (with Load) VOD R = 27; (RS-485) 2 V 1.5 V Change in Magnitude of Driver Differential Output Voltage For 0.2 V 3.0 V 0.2 V Complementary Output States VOC Driver Common Mode Output |VOC| Change in Magnitude of Driver (Figure 1) R = 27 Voltage Common Mode Output Voltage For Complementary Output States VIH Input High Voltage VIL Input Low Voltage DI, DE, VCL Input Clamp Voltage RE , E IIL IIH IIN VTH 2 V 0.8 IIN = -18 mA -1.5 Input Low Current VIL = 0.4V -200 A Input High Current VIH = 2.4V 20 A VCC = 0V or 5.25V VIN = 12V +1.0 mA Current Input DO/RI, DO/RI DE = 0V VIN = -7V -0.8 mA Differential Input Threshold -7V VCM + 12V +0.2 V -0.2 Voltage for Receiver VTH Receiver Input Hysteresis VCM = 0V VOH Receiver Output High Voltage IOH = -400 A VOL Output Low Voltage IOZR RO 70 mV 2.7 V IOL = 16 mA (Note 7) 0.5 V 20 A OFF-State (High Impedance) VCC = Max Output Current at Receiver 0.4V VO 2.4V RIN Receiver Input Resistance -7V VCM +12V ICC Supply Current No Load Driver Outputs Enabled 55 mA (Note 7) Driver Outputs Disabled 35 mA www.national.com 2 12 k (Continued) 0C TA 70C, 4.75V < VCC < 5.25V unless otherwise specified Symbol IOSD IOSR Parameter Conditions Min Typ Max Units Driver Short-Circuit VO = -7V (Note 7) -250 mA Output Current VO = +12V (Note 7) +250 mA Receiver Short-Circuit VO = 0V -85 mA -15 Output Current Note 1: "Absolute Maximum Ratings" are those beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. Note 2: All currents into device pins are positive; all currents out of device pins are negative. All voltages are referenced to device ground unless otherwise specified. Note 3: All typicals are given for VCC = 5V and TA = 25C. Note 4: Derate linearly at 5.56 mW/C to 650 mW at 70C. Note 5: Derate linearly @ 6.11 mW/C to 400 mW at 70C. Note 6: Differential - Input/Output bus voltage is measured at the noninverting terminal A with respect to the inverting terminal B. Note 7: All worst case parameters for which note 7 is applied, must be increased by 10% for DS75176BT. The other parameters remain valid for -40C < TA < +85C. Switching Characteristics VCC = 5.0V, TA = 25C Symbol Parameter Conditions Min Typ Max Units tPLH Driver Input to Output RLDIFF = 60 12 22 ns tPHL Driver Input to Output CL1 = CL2 = 100 pF 17 22 ns tr Driver Rise Time RLDIFF = 60 18 ns tf Driver Fall Time CL1 =CL2 = 100 pF 18 ns (Figure 3 and Figure 5) tZH Driver Enable to Output High CL = 100 pF (Figure 4 and Figure 6) S1 Open 29 100 ns tZL Driver Enable to Output Low CL = 100 pF (Figure 4 and Figure 6) S2 Open 31 60 ns tLZ Driver Disable Time from Low CL = 15 pF (Figure 4 and Figure 6) S2 Open 13 30 ns tHZ Driver Disable Time from High CL = 15 pF (Figure 4 and Figure 6) S1 Open 19 200 ns tPLH Receiver Input to Output CL = 15 pF (Figure 2 and Figure 7) 30 37 ns tPHL Receiver Input to Output S1 and S2 Closed 32 37 ns tZL Receiver Enable to Output Low CL = 15 pF (Figure 2 and Figure 8) S2 Open 15 20 ns tZH Receiver Enable to Output High CL = 15 pF (Figure 2 and Figure 8) S1 Open 11 20 ns tLZ Receiver Disable from Low CL = 15 pF (Figure 2 and Figure 8) S2 Open 28 32 ns tHZ Receiver Disable from High CL = 15 pF (Figure 2 and Figure 8) S1 Open 13 35 ns 3 www.national.com DS75176B/DS75176BT Electrical Characteristics (Notes 2, 3) DS75176B/DS75176BT AC Test Circuits 00875904 FIGURE 3. 00875902 FIGURE 1. 00875905 Note: Unless otherwise specified the switches are closed. FIGURE 4. 00875903 Note: S1 and S2 of load circuit are closed except as otherwise mentioned. FIGURE 2. Switching Time Waveforms 00875906 FIGURE 5. Driver Propagation Delays and Transition Times www.national.com 4 DS75176B/DS75176BT Switching Time Waveforms (Continued) 00875907 FIGURE 6. Driver Enable and Disable Times 00875908 Note: Differential input voltage may may be realized by grounding RI and pulsing RI between +2.5V and -2.5V FIGURE 7. Receiver Propagation Delays 00875909 FIGURE 8. Receiver Enable and Disable Times 5 www.national.com DS75176B/DS75176BT Function Tables DS75176B Transmitting Inputs Line Outputs RE DE DI Condition DO DO X 1 1 No Fault 0 1 X 1 0 No Fault 1 0 X 0 X X Z Z X 1 X Fault Z Z DS75176B Receiving Inputs Outputs RE DE RI-RI RO 0 0 +0.2V 1 0 0 -0.2V 0 0 0 Inputs Open** 1 1 0 X Z X -- Don't care condition Z -- High impedance state Fault -- Improper line conditons causing excessive power dissipation in the driver, such as shorts or bus contention situations **This is a fail safe condition Typical Application 00875911 www.national.com 6 DS75176B/DS75176BT Physical Dimensions inches (millimeters) unless otherwise noted Lit. # 103669 Molded Dual-In-Line Package (N) Order Number DS75176BN or DS75176BTN NS Package Number N08E 7 www.national.com DS75176B/DS75176BT Multipoint RS-485/RS-422 Transceivers Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated