PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 1 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Specifications:
Resistance range : 1Ωto 1MΩ.
Finished size : 1.85mm x 3.5mm.
Lead wire diameter : 0.45 ±0.05mm.
Pitch of tape (PT) : 52mm.
Dimension:
Type Power Rating
(W)
Maximum
D
Maximum
Ld ±0.05 H ±3
MC 1/8 1.85 3.5 0.45 28
Dimensions : Millimetres
Dimensions : Millimetres
Ratings
Type MC
Rated power 0.125W at 70°C
Maximum working voltage 200V
Maximum overload voltage
400V
Dielectric withstanding voltage
Rated ambient temperature 70°C
Operating temperature range -55 °C to +155°C
Resistance tolerance ±5%
Resistance range 1.1MΩ to 1MΩ
PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 2 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Power Rating:
Resistors shall have a power rating based on continuous full load operation at an ambient temperature of 70°C. For temperature in excess of 70°C, the load shall be derated.
Voltage Rating:
Resistors shall have a rated direct-current (DC) continuous working voltage or an approximate sine-wave root-mean-square (RMS) alternating-current (AC) continuous working voltage
at commercial-line frequency and waveform corresponding to the power rating, as determined from the following formula :
RCWV = √Px R
Were: RCWV = Rated DC or RMS AC continuous working voltage at commercial-line frequency and waveform (volt)
P = Power rating (watt)
R = Nominal resistance (ohm)
In no case shall the rated DC or RMS AC continuous working voltage be greater than the applicable maximum value.
Percent Rated Load (%)
Ambient Temperature (°C)
PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 3 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Nominal Resistance:
Effective figures of nominal resistance shall be in accordance with E-24 series, and resistance tolerance
Construction:
Item Number Name Material
1Basic body Rod type ceramics
2Resistance film Carbon film
3End cap Steel (tin plated iron surface)
4Lead wire Annealed copper wire coated with tin
5 Joint By welding
6 Coating Insulated epoxy resin (colour: beige)
7Colour code Epoxy resin
PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 4 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Characteristics
Dielectric withstanding
voltage
No evidence of flashover mechanical
damage, arcing or insulation break
down
Resistors shall be clamped in the trough of a 90° metallic V-block or foil method use a metal foil shall be
wrapped closely around the body of the resistor. After that shall be tested at DC potential respectively
specified in the above list for 60 +10/-0 seconds.
(Sub-clause 4.7)
Temperature coefficient
Resistance Range TCR (PPM/°C) Natural resistance change per temperature degree centigrade
R2-R1/R1(t2-t1) x 106 (PPM/°C)
R1: Resistance value at room temperature (t1)
R2: Resistance value at room temperature plus 100°C (t2)
(Sub-clause 4.8)
≤10Ω0 to ±350
11Ωto 99K 0 to -450
100K to 1M 0 to -700
1.1M to 10M 0 to -1500
Short time overload
Resistance change rate is
±(1% + 0.05Ω) maximum with no
evidence of mechanical damage
Permanent resistance change after the application of a potential of 2.5 times RCWV for 5 seconds
(Sub-clause 4.13)
Terminal strength No evidence of mechanical damage
Direct load:
Resistance to a 2.5kg direct load for 10 seconds in the direction of the longitudinal axis of the terminal
leads.
Twist test:
Terminal leads shall be bent through 90° at a point of about 6mm from the body of the resistor and shall be
rotated through 360° about the original axis of the bent terminal in alternating direction for a total of 3
rotations.
(Sub-clause 4.16)
Characteristics Limits Test Methods (JIS C 5201-1)
DC resistance Must be within the specified tolerance The limit of error of measuring apparatus shall not exceed allowable range or 5% of resistance tolerance
(Sub-clause 4.5)
Insulation resistance Insulation resistance 10,000MΩ
minimum
Resistors shall be clamped in the trough of a 90° metallic V-block or foil method use a metal foil shall be
wrapped closely around the body of the resistor. After that shall be tested at DC potential respectively
specified in the above list for 60 +10/-0 seconds.
(Sub-clause 4.6)
PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 5 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Characteristics
Characteristics Limits Test Methods (JIS C 5201-1)
Solderability 95% coverage minimum
The area covered with a new, smooth clean, shiny and continuous surface free from concentrated
pinholes.
Test temperature of solder : 245°C ±3°C
Dwell time in solder : 2 to 3 seconds
(Sub-clause 4.17)
Soldering temperature
reference
Electrical characteristics shall be satisfied.
Without distinct deformation in appearance.
(95% coverage minimum)
The leads immersed into solder bath to 3.2 to 4.8mm from the body. Permanent resistance change
shall be checked.
Wave soldering condition: (2 cycles maximum)
Pre-heat : 100 to 120°C, 30 ±5 seconds.
Suggestion solder temperature : 235 to 255°C, 10 seconds maximum
Park temperature : 260°C
Hand soldering condition:
Hand Soldering bit temperature : 380 ±10°C
Dwell time in solder : 3 +1/-0 seconds
Resistance to soldering heat
Resistance change rate is ±(1% + 0.05Ω)
maximum with no evidence of mechanical
damage
Permanent resistance change when leads immersed to 3.2 to 4.8 mm from the body in 350°C ±10°C
solder for 3 ±0.5 seconds
(Sub-clause 4.18)
Temperature cycling
Resistance change rate is ±(1% + 0.05Ω)
maximum with no evidence of mechanical
damage
Resistance change after continuous 5 cycles for duty shown below:
(Sub-clause 4.19)
Step Temperature Time
1-55°C ±3°C 30 minutes
2Room temperature 10 to 15 minutes
3155°C ±2°C 30 minutes
4Room temperature 10 to 15 minutes
PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 6 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Characteristics
Characteristics Limits Test Methods (JIS C 5201-1)
Vibration Resistance change rate is ±(1% + 0.05Ω)
maximum
55Hz, 3 planes 2 hours each
Total amplitude = 1.5mm
(Sub-clause 4.22)
Load life in humidity
Resistance change after 1000 hours operating at RCWV with duty cycle of (1.5 hours "on", 0.5 hour
"off") in a humidity test chamber controlled at 40°C ±2°C and 90 to 95% relative humidity
(Sub-clause 4.24.2.1)
Load life
Permanent resistance change after 1000 hours operating at RCWV with duty cycle of (1.5 hours "on",
0.5 hour "off") at 70°C ±2°C ambient
(Sub-clause 4.25.1)
Resistance to solvent No deterioration of protective coatings and
markings
Specimens shall be immersed in a bath of trichloroethane completely for 3 minutes with ultrasonic
(Sub-clause 4.30)
Resistance Value ∆∆R/R
Normal
Type <100KΩ±3%
±5%
Resistance Value ∆∆R/R
Normal
Type
<56KΩ±2%
≥56KΩ±3%
PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 7 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Specification Table
Description Wattage
(mW) Resistance Value Part Number
Carbon Film Resistor 125
1R MCRE000001
1R2 MCRE000002
1R5 MCRE000003
1R8 MCRE000004
2R2 MCRE000005
Marking:
Resistor:
Resistor shall be marked with colour coding, colours shall be in accordance with JIS C 0802.
Painting Method:
Welding point, terminal and lead wire, is permissible to be exposed without the outer coated cover.
The extent should be within 1/2 of the angle.
PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 8 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Specification Table
Description Wattage
(mW) Resistance Value Part Number
Carbon Film Resistor 125
2R7 MCRE000006
3R3 MCRE000007
3R9 MCRE000008
4R7 MCRE000009
5R6 MCRE000010
6R8 MCRE000011
8R2 MCRE000012
10R MCRE000013
12R MCRE000014
15R MCRE000015
18R MCRE000016
22R MCRE000017
27R MCRE000018
33R MCRE000019
39R MCRE000020
47R MCRE000021
56R MCRE000022
68R MCRE000023
82R MCRE000024
100R MCRE000025
120R MCRE000026
PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 9 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Specification Table
Description Wattage
(mW) Resistance Value Part Number
Carbon Film Resistor 125
150R MCRE000027
180R MCRE000028
220R MCRE000029
270R MCRE000030
330R MCRE000031
390R MCRE000032
470R MCRE000033
560R MCRE000034
680R MCRE000035
820R MCRE000036
1K MCRE000037
1K2 MCRE000038
1K5 MCRE000039
1K8 MCRE000040
2K2 MCRE000041
2K7 MCRE000042
3K3 MCRE000043
3K9 MCRE000044
4K7 MCRE000045
5K6 MCRE000046
6K8 MCRE000047
PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 10 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Specification Table
Description Wattage
(mW) Resistance Value Part Number
Carbon Film Resistor 125
8K2 MCRE000048
10K MCRE000049
12K MCRE000050
15K MCRE000051
18K MCRE000052
22K MCRE000053
27K MCRE000054
33K MCRE000055
39K MCRE000056
47K MCRE000057
56K MCRE000058
68K MCRE000059
82K MCRE000060
100K MCRE000061
120K MCRE000062
150K MCRE000063
180K MCRE000064
220K MCRE000065
270K MCRE000066
330K MCRE000067
390K MCRE000068
PART NO.
ECN # REV
-A
REVISIONS
DESCRIPTION DRAWN DATE DATE DATECHECKD APPRVD
Kiran 07/05/09 07/05/09 21/05/09
Suresh Farnell
RELEASED
MCRE0000 Series
This data sheet and its contents (the "Information") belong to the Premier Farnell Group
(the "Group") or are licensed to it. No licence is granted for the use of it other than for
information purposes in connection with the products to which it relates. No licence
of any intellectual property rights is granted. The Information is subject to change with-
out notice and replaces all data sheets previously supplied. The Information supplied is
believed to be accurate but the Group assumes no responsibility for its accuracy or
completeness, any error in or omission from it or for any use made of it. Users of this
data sheet should check for themselves the Information and the suitability of the prod-
ucts for their purpose and not make any assumptions based on information included or
omitted. Liability for loss or damage resulting from any reliance on the Information or
use of it (including liability resulting from negligence or where the Group was aware of
the possibility of such loss or damage arising) is excluded. This will not operate to limit
or restrict the Group's liability for death or personal injury resulting from its negligence.
SPC MULTICOMP is the registered trademark of the Group. © Premier Farnell plc 2009.
TOLERANCES: DRAWN BY:
Kiran
Suresh
Farnell
CHECKED BY:
APPROVED BY:
DATE: DRAWING TITLE:
1700197-1700277
1700197-1700277_DWG
M10002174
07/05/09
DATE: SIZE
SCALE: NTS U.O.M.: mm SHEET: 11 OF 10
DWG NO. ELECTRONIC FILE REV
A
07/05/09 A
DATE:
21/05/09
UNLESS OTHERWISE
SPECIFIED,
DIMENSIONS ARE
FOR REFERENCE
PURPOSES ONLY.
Specification Table
Description Wattage
(mW) Resistance Value Part Number
Carbon Film Resistor 125
470K MCRE000069
560K MCRE000070
680K MCRE000071
820K MCRE000072
1M MCRE000073
http://www.farnell.com
http://www.newark.com
http://www.cpc.co.uk
