MC74AC05, MC74ACT05 Hex Inverter with Open-Drain Outputs The MC74AC/ACT05 is identical in pinout to the LS05. The device inputs are compatible with standard CMOS outputs; with pullup resistors, they are compatible with TTL outputs. http://onsemi.com Features * Outputs Source/Sink 24 mA * ACT05 Has TTL Compatible Inputs * Pb-Free Packages are Available PDIP-14 N SUFFIX CASE 646 1 VCC A6 Y6 A5 Y5 A4 Y4 14 13 12 11 10 9 8 SOIC-14 D SUFFIX CASE 751A 1 1 2 3 4 5 6 7 A1 Y1 A2 Y2 A3 Y3 GND TSSOP-14 DT SUFFIX CASE 948G 1 Top View SOEIAJ-14 M SUFFIX CASE 965 Figure 1. Pinout: 14-Lead Packages 1 FUNCTION TABLE 2, 4, 6, 8, 10, 12 A NOTE: Input A Output Y L H Z L Z = High Impedance Y* ORDERING INFORMATION 1, 3, 5, 9, 11, 13 See detailed ordering and shipping information in the package dimensions section on page 5 of this data sheet. PIN 14 = VCC PIN 7 = GND * DENOTES OPEN-DRAIN OUTPUTS DEVICE MARKING INFORMATION See general marking information in the device marking section on page 6 of this data sheet. Figure 2. Logic Diagram (c) Semiconductor Components Industries, LLC, 2006 October, 2006 - Rev. 8 1 Publication Order Number: MC74AC05/D MC74AC05, MC74ACT05 MAXIMUM RATINGS Symbol Parameter Value Unit VCC DC Supply Voltage (Referenced to GND) -0.5 to +7.0 V Vin DC Input Voltage (Referenced to GND) -0.5 to VCC + 0.5 V Vout DC Output Voltage (Referenced to GND) -0.5 to VCC + 0.5 V Iin DC Input Current, per Pin 20 mA Iout DC Output Sink/Source Current, per Pin 50 mA ICC DC VCC or GND Current per Output Pin 50 mA Tstg Storage Temperature -65 to +150 C Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. RECOMMENDED OPERATING CONDITIONS Symbol VCC VREG tr, tf Parameter Min Typ Min AC 2.0 5.0 6.0 ACT 4.5 5.0 5.5 0 - VCC VCC @ 3.0 V - 150 - VCC @ 4.5 V - 40 - VCC @ 5.5 V - 25 - VCC @ 4.5 V - 10 - VCC @ 5.5 V - 8.0 - - - 140 C -40 25 85 C Supply Voltage DC Regulated Power Voltage (Ref. to GND) Input Rise and Fall Time (Note 1) AC Devices except Schmitt Inputs Unit V V ns/V tr, tf Input Rise and Fall Time (Note 2) ACT Devices except Schmitt Inputs TJ Junction Temperature (PDIP) TA Operating Ambient Temperature Range IOH Output Current - HIGH - - -24 mA IOL Output Current - LOW - - 24 mA 1. Vin from 30% to 70% VCC; see individual Data Sheets for devices that differ from the typical input rise and fall times. 2. Vin from 0.8 V to 2.0 V; see individual Data Sheets for devices that differ from the typical input rise and fall times. http://onsemi.com 2 ns/V MC74AC05, MC74ACT05 DC CHARACTERISTICS 74AC Symbol Parameter VCC (V) 74AC TA = +25C Typ VIH Minimum High Level Input Voltage VIL Maximum Low Level Input Voltage VOL Maximum Low Level Output Voltage IIN IOLD IOHD TA = -40C to +85C Unit Conditions Guaranteed Limits 3.0 4.5 5.5 1.5 2.25 2.75 2.1 3.15 3.85 2.1 3.15 3.85 V VOUT = 0.1 V or VCC - 0.1 V 3.0 4.5 5.5 1.5 2.25 2.75 0.9 1.35 1.65 0.9 1.35 1.65 V VOUT = 0.1 V or VCC - 0.1 V 3.0 4.5 5.5 0.002 0.001 0.001 0.1 0.1 0.1 0.1 0.1 0.1 V 3.0 4.5 5.5 - - - 0.36 0.36 0.36 0.44 0.44 0.44 Maximum Input Leakage Current 5.5 - 0.1 Minimum Dynamic Output Current 5.5 - 5.5 - IOUT = 50 mA V *VIN = VIL or VIH 12 mA IOL 24 mA 24 mA 1.0 mA VI = VCC, GND - 75 mA VOLD = 1.65 V Max - -75 mA VOHD = 3.85 V Min mA VIN = VCC or GND ICC Maximum Quiescent Supply Current 5.5 - 4.0 40 *All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. NOTE: IIN and ICC @ 3.0 V are guaranteed to be less than or equal to the respective limit @ 5.5 V. AC CHARACTERISTICS Symbol Parameter VCC* (V) 74AC 74AC TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Min Typ Max Min Max Unit tPZL Propagation Delay Output Enable 3.3 5.0 1.5 1.5 - - 8.0 6.0 1.0 1.0 9.0 6.5 ns tPLZ Propagation Delay Output Enable 3.3 5.0 1.5 1.5 - - 8.0 6.0 1.0 1.0 9.0 6.5 ns *Voltage Range 3.3 V is 3.3 V 0.3 V. Voltage Range 5.0 V is 5.0 V 0.5 V. http://onsemi.com 3 MC74AC05, MC74ACT05 DC CHARACTERISTICS 74ACT Symbol VCC (V) Parameter 74ACT TA = +25C TA = -40C to +85C Typ Unit Conditions Guaranteed Limits VIH Minimum High Level Input Voltage 4.5 5.5 1.5 1.5 2.0 2.0 2.0 2.0 V VOUT = 0.1 V or VCC - 0.1 V VIL Maximum Low Level Input Voltage 4.5 5.5 1.5 1.5 0.8 0.8 0.8 0.8 V VOUT = 0.1 V or VCC - 0.1 V VOL Maximum Low Level Output Voltage 4.5 5.5 0.001 0.001 0.1 0.1 0.1 0.1 V 4.5 5.5 - - 0.36 0.36 0.44 0.44 0.44 Maximum Input Leakage Current 5.5 - 0.1 1.0 mA VI = VCC, GND DICCT Additional Max. ICC/Input 5.5 0.6 - 1.5 mA VI = VCC - 2.1 V IOLD IOHD Minimum Dynamic Output Current 5.5 5.5 - - - - 75 -75 mA mA VOLD = 1.65 V Max VOHD = 3.85 V Min ICC Maximum Quiescent Supply Current 5.5 - 4.0 40 mA VIN = VCC or GND IIN IOUT = 50 mA *VIN = VIL or VIH IOH 24 mA *All outputs loaded; thresholds on input associated with output under test. Maximum test duration 2.0 ms, one output loaded at a time. AC CHARACTERISTICS Symbol VCC* (V) Parameter 74ACT 74ACT TA = +25C CL = 50 pF TA = -40C to +85C CL = 50 pF Min Typ Max Min Max Unit tPZL Propagation Delay Output Enable 5.0 1.5 - 8.0 1.0 8.5 ns tPLZ Propagation Delay Output Enable 5.0 1.5 - 8.5 1.0 9.0 ns *Voltage Range 5.0 V is 5.0 V 0.5 V. CAPACITANCE Symbol Parameter Value Typ Unit Test Conditions CIN Input Capacitance 4.5 pF VCC = 5.0 V CPD Power Dissipation Capacitance 30 pF VCC = 5.0 V http://onsemi.com 4 MC74AC05, MC74ACT05 ORDERING INFORMATION Device Package MC74AC05N PDIP-14 MC74AC05NG PDIP-14 (Pb-Free) MC74AC05D SOIC-14 MC74AC05DG SOIC-14 (Pb-Free) MC74AC05DR2 SOIC-14 MC74AC05DR2G SOIC-14 (Pb-Free) MC74AC05MEL SOEIAJ-14 MC74AC05MELG SOEIAJ-14 (Pb-Free) MC74ACT05N PDIP-14 MC74ACT05NG PDIP-14 (Pb-Free) MC74ACT05D SOIC-14 MC74ACT05DG SOIC-14 (Pb-Free) MC74ACT05DR2 SOIC-14 MC74ACT05DR2G SOIC-14 (Pb-Free) MC74ACT05DTR2 TSSOP-14* MC74ACT05DTR2G TSSOP-14* MC74ACT05MEL SOEIAJ-14 MC74ACT05MELG SOEIAJ-14 (Pb-Free) Shipping 25 Units / Rail 55 Units / Rail 2500 / Tape & Reel 2000 / Tape & Reel 25 Units / Rail 55 Units / Rail 2500 / Tape & Reel 2000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. *These packages are inherently Pb-Free. http://onsemi.com 5 MC74AC05, MC74ACT05 MARKING DIAGRAMS PDIP-14 SOIC-14 SOEIAJ-14 14 14 14 AC05G AWLYWW MC74AC05N AWLYYWWG 1 1 14 14 74AC05 ALYWG 1 14 14 ACT 05 ALYWG G ACT05G AWLYWW MC74ACT05N AWLYYWWG 1 TSSOP-14 1 1 A = Assembly Location WL, L = Wafer Lot YY, Y = Year WW, W = Work Week G or G = Pb-Free Package (Note: Microdot may be in either location) http://onsemi.com 6 74ACT05 ALYWG 1 MC74AC05, MC74ACT05 PACKAGE DIMENSIONS PDIP-14 CASE 646-06 ISSUE P 14 8 1 7 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. B A F L N C -T- SEATING PLANE H G D 14 PL J K 0.13 (0.005) M M http://onsemi.com 7 DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 --- 10 _ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 --- 10 _ 0.38 1.01 MC74AC05, MC74ACT05 PACKAGE DIMENSIONS SOIC-14 CASE 751A-03 ISSUE H NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. -A- 14 8 -B- P 7 PL 0.25 (0.010) M 7 1 G -T- D 14 PL 0.25 (0.010) T B S A DIM A B C D F G J K M P R J M K M F R X 45 _ C SEATING PLANE B M S SOLDERING FOOTPRINT* 7X 7.04 14X 1.52 1 14X 0.58 1.27 PITCH DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 8 MILLIMETERS MIN MAX 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.19 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0_ 7_ 0.228 0.244 0.010 0.019 MC74AC05, MC74ACT05 PACKAGE DIMENSIONS TSSOP-14 CASE 948G-01 ISSUE A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7. DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S S S N 2X 14 L/2 M B -U- L PIN 1 IDENT. N F 7 1 0.15 (0.006) T U 0.25 (0.010) 8 S DETAIL E K A -V- EEE CCC CCC EEE CCC K1 J J1 SECTION N-N -W- C 0.10 (0.004) -T- SEATING PLANE D G H DETAIL E http://onsemi.com 9 DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 --- 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.50 0.60 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 --- 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.020 0.024 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ MC74AC05, MC74ACT05 PACKAGE DIMENSIONS SOEIAJ-14 CASE 965-01 ISSUE A 14 LE 8 Q1 E HE L 7 1 M_ DETAIL P Z D VIEW P A e DIM A A1 b c D E e HE 0.50 LE M Q1 Z A1 b 0.13 (0.005) c NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5. THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). M 0.10 (0.004) MILLIMETERS MIN MAX --- 2.05 0.05 0.20 0.35 0.50 0.10 0.20 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --- 1.42 INCHES MIN MAX --- 0.081 0.002 0.008 0.014 0.020 0.004 0.008 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --- 0.056 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 10 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74AC05/D