SI4421-A0-FT - Silicon Labs - Datasheet.Directory

Si4421

PIN ASSIGNMENT

This document refers to Si4421-IC rev A1.

See www.silabs.com/integration for any applicable errata.

See back page for ordering information.

Si4421 Universal ISM Band

FSK Transceiver

DESCRIPTION

Silicon Labs’ Si4421 is a single chip, low power, multi-channel FSK

ransceiver designed for use in applications requiring FCC or ETSI

conformance for unlicensed use in the 433, 868 and 915 MHz bands.

The Si4421 transceiver is a part of Silicon Labs’ EZRadioTM

product

line, which produces a flexible, low cost, and highly integrated solution

hat does not require production alignments. The chip is a complete

analog RF and baseband transceiver including a multi-band PLL

synthesizer with PA, LNA, I/Q down converter mixers, baseband filters

and amplifiers, and an I/Q demodulator. All required RF functions are

integrated. Only an external crystal and bypass filtering are needed for

operation.

The Si4421 features a completely integrated PLL for easy RF design,

and its rapid settling time allows for fast frequency-hopping, bypassin

multipath fading and interference to achieve robust wireless links. The

PLL’s high resolution allows the usage of multiple channels in any o

he bands. The receiver baseband bandwidth (BW) is programmable to

accommodate various deviation, data rate and crystal tolerance

requirements. The transceiver employs the Zero-IF approach with I/Q

demodulation. Consequently, no external componen

s (except crystal

and decoupling) are needed in most applications.

The Si4421 dramatically reduces the load on the microcontroller with

he integrated digital data processing features: data filtering, clock

recovery, data pattern recognition, integrated FIFO and TX data

of a low accuracy (low cost) crystal. To minimize the system cost, the

Si4421 can provide a clock signal for the microcontroller, avoiding the

need for two crystals.

For low power applications, the Si4421 supports low duty cycle

operation based on the internal wake-up timer.

FUNCTIONAL BLOCK DIAGRAM

Si4421-DS rev 2.4r 0708 www.silabs.com

RF Parts Data processing units

Low Power parts

AMP OC

LNA

MIX I

MIX

Data Filt

CLK Rec data

clk

BB Amp/Filt./Limiter

DQDCOMP

RSSI AFC

Self cal.

PLL & I/Q VCO

with cal.

ControllerXosc LBD

WTM

with cal.

CLK div Bias

RF1

RF2 12

DCLK /

CFIL /

FFIT /

FSK /

DATA /

nFFS

FIFO

8 9

CLK XTL /

REF

nINT /

VDI

ARSSI

23 4 511

SCK nSEL SDO nIRQ

VSS VDD

SDI

nRES

I/Q

DEMOD

FEATURES

 Fully integrated (low BOM, easy design-in)

 No alignment required in production

 Fast-settling, programmable, high-resolution PLL synthesizer

 Fast frequency-hopping capability

 High bit rate (up to 115.2 kbps in digital mode and 256 kbps

in analog mode)

 Direct differential antenna input/output

 Integrated power amplifier

 Programmable TX frequency deviation (15 to 240 kHz)

 Programmable RX baseband bandwidth (67 to 400 kHz)

 Analog and digital RSSI outputs

 Automatic frequency control (AFC)

 Data quality detection (DQD)

 Internal data filtering and clock recovery

 RX synchron pattern recognition

 SPI compatible serial control interface

 Clock and reset signals for microcontroller

 16-bit RX Data FIFO

 Two 8-bit TX data registers

 Low power duty cycle mode

 Standard 10 MHz crystal reference with on-chip tuning

 Wake-up timer

 2.2 to 3.8 V supply voltage

 Low power consumption

 Low standby current (0.3 A)

 Compact 16 pin TSSOP package

 Supports very short packets (down to 3 bytes)

 Excellent temperature stability of the RF parameters

 Good adjacent channel rejection/blocking

TYPICAL APPLICATIONS

 Home security and alarm

 Remote control, keyless entry

 Wireless keyboard/mouse and other PC peripherals

 Toy controls

 Remote keyless entry

 Tire pressure monitoring

 Telemetry

 Personal/patient data logging

 Remote automatic meter reading

Si4421

DETAILED FEATURE-LEVEL DESCRIPTION

The Si4421 FSK transceiver is designed to cover the unlicensed

frequency bands at 433, 868 and 915 MHz. The device

facilitates compliance with FCC and ETSI requirements.

The receiver block employs the Zero-IF approach with I/Q

demodulation, allowing the use of a minimal number of external

components in a typical application. The Si4421 incorporates a

fully integrated multi-band PLL synthesizer, PA with antenna

tuning, an LNA with switchable gain, I/Q down converter mixers,

baseband filters and amplifiers, and an I/Q demodulator

followed by a data filter.

PLL

The programmable PLL synthesizer determines the operating

frequency, while preserving accuracy based on the on-chip crystal-

controlled reference oscillator. The PLL’s high resolution allows the

usage of multiple channels in any of the bands.

RF Power Amplifier (PA)

The power amplifier has an open-collector differential output and

can directly drive different PCB antennas with a programmable

output power level. An automatic antenna tuning circuit is built in

to avoid costly trimming procedures and the so-called “hand

effect”.

LNA

The LNA has approximately 250 Ohm input impedance, which

functions well with the proposed antennas (see: Application

Notes available from www.silabs.com/integration)

If the RF input of the chip is connected to 50 Ohm devices, an

external matching circuit is required to provide the correct

matching and to minimize the noise figure of the receiver.

The LNA gain can be selected in four steps (between 0 and

-20dB relative to the highest gain) according to RF signal

strength. It can be useful in an environment with strong

interferers.

Baseband Filters

The receiver bandwidth is selectable by programming the

bandwidth (BW) of the baseband filters. This allows setting up

the receiver according to the characteristics of the signal to be

received.

An appropriate bandwidth can be chosen to accommodate

various FSK deviation, data rate and crystal tolerance

requirements. The filter structure is 7th order Butterworth low-

pass with 40 dB suppression at 2 · BW frequency. Offset

cancellation is done by using a high-pass filter with a cut-off

frequency below 7 kHz.

Full Baseband Amplifier Transfer Function

BW=67kHz

Data Filtering and Clock Recovery

Output data filtering can be completed by an external capacitor

or by using digital filtering according to the final application.

Analog operation: The filter is an RC type low-pass filter followed

by a Schmitt-trigger (St). The resistor (10 kOhm) and the St are

integrated on the chip. An (external) capacitor can be chosen

according to the actual bit rate. In this mode, the receiver can

handle up to 256 kbps data rate. The FIFO cannot be used in this

mode and clock is not provided for the demodulated data.

Digital operation: A digital filter is used with a clock frequency at

29 times the bit rate. In this mode, there is a clock recovery

circuit (CR), which can provide synchronized clock to the data.

Using this clock the received data can fill a FIFO. The CR has

three operation modes: fast, slow, and automatic. In slow mode,

its noise immunity is very high, but it has slower settling time and

requires more accurate data timing than in fast mode. In

automatic mode, the CR automatically changes between fast and

slow mode. The CR starts in fast mode, then after locking, it

automatically switches to slow mode

(Only the digital data filter and the clock recovery use the bit rate

clock. For analog operation, there is no need for setting the

correct bit rate.)

Si4421

Data Validity Blocks

RSSI

A digital RSSI output is provided to monitor the input signal level.

It goes high if the received signal strength exceeds a given

preprogrammed level. An analog RSSI signal is also available.

The RSSI settling time depends on the external filter capacitor.

Pin 15 is used as analog RSSI output. The digital RSSI can be

monitored by reading the status register.

Typical Analog ARSSI Voltage vs. RF Input Power

DQD

The operation of the Data Quality Detector is based on counting

the spikes on the unfiltered received data. High output signal

indicates an operating FSK transmitter within baseband filter

bandwidth from the local oscillator. DQD threshold parameter

can be set by using the Data Filter Command (page 19).

AFC

By using an integrated Automatic Frequency Control (AFC)

feature, the receiver can minimize the TX/RX offset in discrete

steps, allowing the use of:

 Narrower receiver bandwidth (i.e. increased

sensitivity)

 Higher data rate

 Inexpensive crystals

Crystal Oscillator

The Si4421 has a single-pin crystal oscillator circuit, which

provides a 10 MHz reference signal for the PLL. To reduce

external parts and simplify design, the crystal load capacitor is

internal and programmable. Guidelines for selecting the

appropriate crystal can be found later in this datasheet.

The transceiver can supply a clock signal for the microcontroller;

so accurate timing is possible without the need for a second

crystal.

When the microcontroller turns the crystal oscillator off by

clearing the appropriate bit using the Power Management

Command (page 15), the chip provides a fixed number (192) of

further clock pulses (“clock tail”) for the microcontroller to let it

go to idle or sleep mode. If this clock output is not used, it is

suggested to turn the output buffer off by the Power

Management Command (page 15).

Low Battery Voltage Detector

The low battery detector circuit monitors the supply voltage and

generates an interrupt if it falls below a programmable threshold

level. The detector circuit has 50 mV hysteresis.

Wake-Up Timer

The wake-up timer has very low current consumption (1.5 µA

typical) and can be programmed from 1 ms to several days with

an accuracy of ±10%.

The wake-up timer calibrates itself to the crystal oscillator at

every startup. For proper calibration of the wake-up timer the

crystal oscillator must be running before the wake-up timer is

enabled. The calibration process takes approximately 0.5ms.

For the crystal start up time (tsx), see page 11.

Event Handling

In order to minimize current consumption, the transceiver

supports different power saving modes. Active mode can be

initiated by several wake-up events (negative logical pulse on

nINT input, wake-up timer timeout, low supply voltage detection,

on-chip FIFO filled up or receiving a request through the serial

interface).

If any wake-up event occurs, the wake-up logic generates an

interrupt signal, which can be used to wake up the

microcontroller, effectively reducing the period the

microcontroller has to be active. The source of the interrupt can

be read out from the transceiver by the microcontroller through

the SDO pin.

Interface and Controller

An SPI compatible serial interface lets the user select the

frequency band, center frequency of the synthesizer, and the

bandwidth of the baseband signal path. Division ratio for the

microcontroller clock, wake-up timer period, and low supply

voltage detector threshold are also programmable. Any of these

auxiliary functions can be disabled when not needed. All

parameters are set to default after power-on; the programmed

values are retained during sleep mode. The interface supports

the read-out of a status register, providing detailed information

about the status of the transceiver and the received data.

The transmitter block is equipped with two 8-bit wide TX data

registers. It is possible to write 8 bits into the register in burst

mode and the internal bit rate generator transmits the bits out

with the predefined rate. For further details, see the TX Register

Buffered Data Transmission section (page 28).

It is also possible to store the received data bits into a FIFO

Si4421

PACKAGE PIN DEFINITIONS

Pin type key: D=digital, A=analog, S=supply, I=input, O=output, IO=input/output

Pin Name Type Function

1 SDI DI Data input of the serial control interface

2 SCK DI Clock input of the serial control interface

3 nSEL DI Chip select input of the serial control interface (active low)

4 SDO DO Serial data output with bus hold

5 nIRQ DO Interrupt request output (active low)

FSK DI Transmit FSK data input (internal pull up resistor 133 k)

DATA DO Received data output (FIFO not used)

nFFS DI

FIFO select input (active low). In FIFO mode, when bit ef is set in Configuration Setting Command,

page 15 (internal pull up resistor 133 k)

DLCK DO Received data clock output (Digital filter used, FIFO not used)

CFIL AIO External data filter capacitor connection (Analog filter used)

FFIT DO FIFO interrupt (active high). In FIFO mode, when bit ef is set in Configuration Setting Command

8 CLK DO Microcontroller clock output

XTL AIO Crystal connection (the other terminal of crystal to VSS) or external reference input

REF AIO External reference input. Use 33 pF series coupling capacitor

10 nRES DIO Open drain reset output with internal pull-up and input buffer (active low)

11 VSS S Ground reference voltage

12 RF2 AIO RF differential signal input/output

13 RF1 AIO RF differential signal input/output

14 VDD S Positive supply voltage

15 ARSSI AO Analog RSSI output

nINT DI Interrupt input (active low)

VDI DO Valid data indicator output

Note: The actual mode of the multipurpose pins (pin 6 and 7) is determined by the TX/RX data I/O settings of the transceiver.

Si4421

Internal Pin Connections

Pin Name Internal connection

1 SDI

2 SCK

3 nSEL

PAD

1.5k

VSS

VDD

4 SDO

5 nIRQ

FSK

DATA

nFFS

DLCK

CFIL

FFIT

8 CLK PAD

VSS

VDD

XTL

REF

Pin Name Internal connection

10 nRES

11 VSS

12 RF2

13 RF1

14 VDD

15 ARSSI

nINT

VDI

Si4421

PIN6 Logic Diagram (FSK / DATA / nFFS)

PIN10 Logic Diagram (nRES I/O)

* Note: These pins can be left floating.

Si4421

Typical Application

Typical application with FIFO usage

C3 C2

10n

10MHz

2.2u

Si4421

VDD

SCK

SDO

nIRQ

SDI

CLKin

nSEL

nFFS

FFIT

nRES

PCB

Antenna

nRESin

2.2n

CLK

(optional)*

(optional)

(optional)*

(optional)

(opt.)

(optional)

VDI

Note: * Connections needed only in time critical applications

Recommended supply decoupling capacitor values

C2 and C3 should be 0603 size ceramic capacitors to achieve the best supply decoupling.

Band [MHz] C1 C2 C3

433 2.2µF 10nF 220pF

868 2.2µF 10nF 47pF

915 2.2µF 10nF 33pF

Property C1 C2 C3

SMD size A 0603 0603

Dielectric Tantalum Ceramic Ceramic

Pin Function vs. Operation Mode

Mode Bit setting Function Pin 6 Pin 7

el = 0 Internal TX data register disabled TX data input

Transmit

el = 1 Internal TX data register enabled nFFS input

(TX data register can be accessed)

Not used

ef = 0 Receiver FIFO disabled RX data output RX data clock

output

Receive

ef = 1 Receiver FIFO disabled nFFS input

(RX data FIFO can be accessed) FFIT output

The el and ef bits can be found in the Configuration Setting Command on page 15. Bit el enables the internal TX data register.

Bit ef enables the FIFO mode.

Si4421

GENERAL DEVICE SPECIFICATIONS

All voltages are referenced to Vss , the potential on the ground reference pin VSS.

Absolute Maximum Ratings (non-operating)

Symbol Parameter Min Max Units

Vdd Positive supply voltage -0.5 6 V

Vin Voltage on any pin (except RF1 and RF2) -0.5 Vdd +0.5 V

Voc Voltage on open collector outputs (RF1, RF2) -0.5 Vdd +1.5 (Note 1) V

Iin Input current into any pin except VDD and VSS -25 25 mA

ESD Electrostatic discharge with human body model 1000 V

Tst Storage temperature -55 125 oC

Tld Lead temperature (soldering, max 10 s) 260 oC

Recommended Operating Range

Symbol Parameter Min Max Units

Vdd Positive supply voltage 2.2 3.8 V

Voc Voltage range on open collector outputs (RF1, RF2) Vdd -1.5 (Note 2) Vdd +1.5 V

Top Ambient operating temperature -40 85 oC

Note 1: The voltage on RF1 and RF2 pins can be higher than the actual Vdd but cannot exceed 7 V.

Note 2: The actual voltage on RF1 and RF2 pins can be lower than the current Vdd but never should go below 1.2 V.

Si4421

ELECTRICAL SPECIFICATION

Test Conditions: Top = 27 oC; Vdd = Voc = 3.3 V

DC Characteristics

Symbol Parameter Conditions/Notes Min Typ Max Units

433 MHz band 15

868 MHz band 16

Idd_TX_0 Supply current

(TX mode, Pout = 0 dBm)

915 MHz band 17

433 MHz band 22 26

868 MHz band 23 27

Idd_TX_PMAX Supply current

(TX mode, Pout = Pmax)

915 MHz band 24 28

433 MHz band 11 13

868 MHz band 12 14

Idd_RX Supply current (RX mode)

915 MHz band 13 15

Ipd Standby current (Sleep mode) All blocks disabled 0.3 1 µA

Ilb Low battery voltage detector current

consumption 0.5 1.7 µA

Iwt Wake-up timer current consumption 1.5 3.5 µA

Ix Idle current Crystal oscillator on (Note 1) 0.6 1.2 mA

Vlb Low battery detect threshold Programmable in 0.1 V steps 2.25 3.75 V

Vlba Low battery detection accuracy ± 3 %

Vil Digital input low level voltage 0.3·Vdd V

Vih Digital input high level voltage 0.7·Vdd V

Iil Digital input current Vil = 0 V -1 1 µA

Iih Digital input current Vih = Vdd , Vdd = 3.8 V -1 1 µA

Vol Digital output low level Iol = 2 mA 0.4 V

Voh Digital output high level Ioh = -2 mA Vdd -0.4 V

Notes are on page 12.

Si4421

AC Characteristics (PLL parameters)

Symbol Parameter Conditions/Notes Min Typ Max Units

fref PLL reference frequency (Note 2) 9 10 11 MHz

433 MHz band, 2.5 kHz resolution 430.24 439.75

868 MHz band, 5.0 kHz resolution 860.48 879.51

fo Receiver LO/Transmitter carrier

frequency

915 MHz band, 7.5 kHz resolution 900.72 929.27

MHz

tlock PLL lock time Frequency error < 1kHz

after 10 MHz step 30 µs

tstP PLL startup time (Note 10) With a running crystal oscillator 200 300 µs

AC Characteristics (Receiver)

Symbol Parameter Conditions/Notes Min Typ Max Units

mode 0 67

mode 1 134

mode 2 200

mode 3 270

mode 4 340

BW Receiver bandwidth

mode 5 400

kHz

BRRX FSK bit rate (Note 10) With internal digital filters 0.6 115.2 kbps

BRARX FSK bit rate (Note 10) With analog filter 256 kbps

Pmin Receiver Sensitivity BER 10-3, BW=67 kHz, BR=1.2 kbps,

868 MHz Band (Note 3) -110 dBm

AFCrange AFC locking range δfFSK: FSK deviation in the received

signal

0.8

δf

FSK

IIP3inh Input IP3 In band interferers in high bands

(868 MHz, 915 MHz) -21 dBm

IIP3outh Input IP3 Out of band interferers l f-fo l > 4 MHz -18 dBm

IIP3inl IIP3 (LNA –6 dB gain) In band interferers in low band (433

MHz) -15 dBm

IIP3outl IIP3 (LNA –6 dB gain) Out of band interferers l f-fo l > 4 MHz -12 dBm

Pmax Maximum input power LNA: high gain 0 dBm

Cin RF input capacitance 1 pF

RSa RSSI accuracy ± 6 dB

RSr RSSI range 46 dB

RSps RSSI power supply dependency When input signal level lower than -54

dBm and greater than -100 dBm +35 mV/V

CARSSI Filter capacitor for ARSSI 1 nF

RSstep RSSI programmable level steps 6 dB

RSresp DRSSI response time

Until the RSSI signal goes high after

the input signal exceeds the

preprogrammed limit CARRSI = 4.7 nF

500 µs

Psp_rx Receiver spurious emission -60 dBm

Notes are on page 12.

Si4421

AC Characteristics (Transmitter)

Symbol Parameter Conditions/Notes Min Typ Max Units

IOUT Open collector output DC current Programmable 0.5 6 mA

In 433 MHz band 7

Pmax_50

Max. output power delivered to 50

Ohm load over a suitable matching

network (Note 4) In 868 MHz / 915 MHz bands 5

dBm

In 433 MHz band with monopole antenna

with matching network (Note 4) 7

Pmax_ant Max. EIRP with suitable selected

PCB antenna (Note 6)

In 868 MHz / 915 MHz bands (Note 5) 7

dBm

Pout Typical output power Selectable in 2.5 dB steps (Note 7) Pmax-17.5 Pmax dBm

At max power 50 Ohm load (Note 4) -55

Psp Spurious emission

l f-fsp l > 1 MHz With PCB antenna (Note 5) -60

dBc

At max power 50 Ohm load (Note 4) -35

Pharm Harmonic suppression

With PCB antenna (Note 5) -42

dBc

In 433 MHz band 2 2.6 3.2

Co Output capacitance (set by the

automatic antenna tuning circuit) In 868 MHz / 915 MHz bands 2.1 2.7 3.3

In 433 MHz band 13 15 17

Qo Quality factor of the output

capacitance In 868 MHz / 915 MHz bands 8 10 12

100 kHz from carrier, in 868 MHz band -80

Lout Output phase noise

1 MHz from carrier, in 868 MHz band -103

dBc/Hz

BRTX FSK bit rate Via internal TX data register 172 kbps

BRATX FSK bit rate TX data connected to the FSK input 256 kbps

dffsk FSK frequency deviation Programmable in 15 kHz steps 15 240 kHz

AC Characteristics (Turn-on/Turnaround timings)

Symbol Parameter Conditions/Notes Min Typ Max Units

tsx Crystal oscillator startup time

Default capacitance bank setting, crystal

ESR < 50 Ohm (Note 9). Crystal load

capacitance = 16 pF.

2 7 ms

Ttx_XTAL_ON Transmitter turn-on time Synthesizer off, crystal oscillator on with

10 MHz step 250 µs

Trx_XTAL_ON Receiver turn-on time Synthesizer off, crystal oscillator on with

10 MHz step 250 µs

Ttx_rx_SYNT_ON Transmitter – Receiver turnover time Synthesizer and crystal oscillator on

during TX/RX change with 10 MHz step 150 µs

Trx_tx_SYNT_ON Receiver – Transmitter turnover time Synthesizer and crystal oscillator on

during RX/TX change with 10 MHz step 150 µs

AC Characteristics (Others)

Symbol Parameter Conditions/Notes Min Typ Max Units

Cxl Crystal load capacitance,

see crystal selection guide

Programmable in 0.5 pF steps, tolerance

± 10% 8.5 16 pF

tPOR Internal POR timeout After Vdd has reached 90% of final value

(Note 8) 100 ms

tPBt Wake-up timer clock accuracy

Crystal oscillator must be enabled to

ensure proper calibration at the start up.

(Note 9)

± 10 %

CinD Digital input capacitance 2 pF

tr, tf Digital output rise/fall time 15 pF pure capacitive load 10 ns

Notes are on page 12.

Si4421

Note 1: Measured with disabled clock output buffer

Note 2: Not using a 10 MHz crystal is allowed but not recommended because all crystal referred timing and frequency parameters

will change accordingly

Note 3: See the BER diagrams in the measurement results section (page 37) for detailed information

Note 4: See reference design with 50 Ohm Matching Network (page 39) for details

Note 5: See reference design with Resonant PCB Antenna (BIFA) on page 41 for details

Note 6: Optimal antenna admittance/impedance:

Si4421 Yantenna [mS] Zantenna [Ohm] Lantenna [nH]

433 MHz 2 – j5.9 52 + j152 62

868 MHz 1.2 - j11.9 7.8 + j83 15.4

915 MHz 1.49 - j12.8 9 + j77 13.6

Note 7: Adjustable in 8 steps

Note 8: During the Power-On Reset period, commands are not accepted by the chip. In case of software reset (see Wake-Up Timer

Command, page 25) the reset timeout is 0.25ms typical.

Note 9: The crystal oscillator start up time strongly depends on the capacitance seen by the oscillator. Low capacitance and low

ESR crystal is recommended with low parasitic PCB layout design.

Note 10: By design

Si4421

CONTROL INTERFACE

Commands to the transmitter are sent serially. Data bits on pin SDI are shifted into the device upon the rising edge of the clock on

pin SCK whenever the chip select pin nSEL is low. When the nSEL signal is high, it initializes the serial interface. All commands

consist of a command code, followed by a varying number of parameter or data bits. All data are sent MSB first (e.g. bit 15 for a 16-

bit command). Bits having no influence (don’t care) are indicated with X. Special care must be taken when the microcontroller’s built-

in hardware serial port is used. If the port cannot be switched to 16-bit mode then a separate I/O line should be used to control the

nSEL pin to ensure the low level during the whole duration of the command or a software serial control interface should be

implemented. The Power-On Reset (POR) circuit sets default values in all control and command registers.

The receiver will generate an interrupt request (IT) for the microcontroller - by pulling the nIRQ pin low - on the following events:

 The TX register is ready to receive the next byte (RGIT)

 The RX FIFO has received the preprogrammed amount of bits (FFIT)

 Power-on reset (POR)

 RX FIFO overflow (FFOV) / TX register underrun (RGUR)

 Wake-up timer timeout (WKUP)

 Negative pulse on the interrupt input pin nINT (EXT)

 Supply voltage below the preprogrammed value is detected (LBD)

FFIT and FFOV are applicable when the RX FIFO is enabled. RGIT and RGUR are applicable only when the TX register is enabled. To

identify the source of the IT, the status bits should be read out.

Timing Specification

Symbol Parameter Minimum value [ns]

tCH Clock high time 25

tCL Clock low time 25

tSS Select setup time (nSEL falling edge to SCK rising edge) 10

tSH Select hold time (SCK falling edge to nSEL rising edge) 10

tSHI Select high time 25

tDS Data setup time (SDI transition to SCK rising edge) 5

tDH Data hold time (SCK rising edge to SDI transition) 5

tOD Data delay time 10

Timing Diagram

SCK

SDI

SDO

nSEL

tDS tDH

tCH tCL

BIT15 BIT14 BIT13

tSS

BIT8 BIT7

tOD

OFFS (0) FIFO OUT

BIT1 BIT0

tSH

tSHI

FFIT FFOV AT SCRL

Si4421

Control Commands

Control Command Related Parameters/Functions Related control bits

1 Configuration Setting Command Frequency band, crystal oscillator load capacitance,

RX FIFO and TX register enable el, ef, b1 to b0, x3 to x0

2 Power Management Command

Receiver/Transmitter mode change, synthesizer,

crystal oscillator, PA, wake-up timer, clock output

enable er, ebb, et, es, ex, eb, ew, dc

3 Frequency Setting Command Frequency of the local oscillator/carrier signal f11 to f0

4 Data Rate Command Bit rate cs, r6 to r0

5 Receiver Control Command Function of pin 16, Valid Data Indicator, baseband

bandwidth, LNA gain, digital RSSI threshold p16, d1 to d0, i2 to i0, g1 to g0, r2

to r0

6 Data Filter Command Data filter type, clock recovery parameters al, ml, s, f2 to f0

7 FIFO and Reset Mode Command Data FIFO IT level, FIFO start control, FIFO enable

and FIFO fill enable, POR sensitivity f3 to f0, sp, ff, al, dr

8 Synchron Pattern Command Synchron pattern b7 to b0

9 Receiver FIFO Read Command RX FIFO read

10 AFC Command AFC parameters a1 to a0, rl1 to rl0, st, fi, oe, en

11 TX Configuration Control Command Modulation parameters, output power mp, m3 to m0, p2 to p0

12 PLL Setting Command CLK out buffer speed, dithering, PLL bandwidth ob1 to ob0, ddit, dly, bw0

13 Transmitter Register Write Command TX data register write t7 to t0

14 Wake-Up Timer Command Wake-up time period r4 to r0, m7 to m0

15 Low Duty-Cycle Command Enable and set low duty-cycle mode d6 to d0, en

Low Battery Detector and

Microcontroller Clock Divider

Command

LBD voltage and microcontroller clock division ratio d2 to d0, v3 to v0

17 Status Read Command Status bit readout

In general, setting the given bit to one will activate the related function. In the following tables, the POR column shows the default

values of the command registers after power-on.

Control Register Default Values

Control Register Power-On Reset Value

1 Configuration Setting Command 8008h

2 Power Management Command 8208h

3 Frequency Setting Command A680h

4 Data Rate Command C623h

5 Receiver Control Command 9080h

6 Data Filter Command C22Ch

7 FIFO and Reset Mode Command CA80h

8 Synchron Pattern Command CED4h

9 Receiver FIFO Read Command B000h

10 AFC Command C4F7h

11 TX Configuration Control Command 9800h

12 PLL Setting Command CC77h

13 Transmitter Register Write Command B8AAh

14 Wake-Up Timer Command E196h

15 Low Duty-Cycle Command C80Eh

16 Low Battery Detector and Microcontroller Clock Divider Command C000h

17 Status Read Command 0000h

Si4421

Description of the Control Commands

1. Configuration Setting Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 0 0 0 0 0 0 0 el ef b1 b0 x3 x2 x1 x0 8008h

Bit el enables the internal data register.

Bit ef enables the FIFO mode. If ef = 0 then DATA (pin 6) and DCLK (pin 7) are used for data and data clock output.

b1 b0 Freq y Bauenc nd

0 0 Reserved

0 1 3 43

1 0 8 86

1 1 5 91

x3 x2 x1 x0 Crystal Loa d Capacita nce [pF ]

0 8.5 0 0 0

0 9.0 0 0 1

0 9.5 0 1 0

0 10.00 1 1

…

1 15.51 1 0

1 16.01 1 1

2. Power Management Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 0 0 0 0 0 1 0 er ebb et es ex eb ew dc 8208h

Bit Functio n of the control bit Related blocks

er Enables the whole receiver chain RF front end, baseband, synthesizer, crystal oscillator

ebb The receiver baseband circuit can be separately switched on Baseband

et Switches on the PLL, the power amplifier, and starts the

transmission (If TX register is enabled) Power amplifier, synthesizer, crystal oscillator

es Turns on the synthesizer Synthesizer

ex Turns on the crystal oscillator Crystal oscillator

eb Enables the low battery detector Low battery detector

ew Enables the wake-up timer Wake-up timer

dc Disables the clock output (pin 8) Clock output buffer

The ebb, es, and ex bits are provided to optimize the TX to RX or RX to TX turnaround time.

The RF frontend consist of the LNA (low noise amplifier) and the mixer. The synthesizer block has two main components: the VCO

and the PLL. The baseband section contains the baseband amplifier, low pass filter, limiter and the I/Q demodulator.

To decrease TX/RX turnaround time, it is possible to leave the baseband section powered on. Switching to RX mode means disabling

the PA and enabling the RF frontend. Since the baseband block is already on, the internal startup calibration will not be performed,

the turnaround time will be shorter.

The synthesizer also has an internal startup calibration procedure. If quick RX/TX switching needed it may worth to leave this block

on. Enabling the transmitter using the et bit will turn on the PA, the synthesizer is already up and running. The power amplifier almost

immediately produces TX signal at the output.

The crystal oscillator provides reference signal to the RF synthesizer, the baseband circuits and the digital signal processor part.

When the receiver or the transmitter part frequently used, it is advised to leave the oscillator running because the crystal might need

a few milliseconds to start. This time mainly depends on the crystal parameters.

It is important to note that leaving blocks unnecessary turned on can increase the current consumption thus decreasing the battery

life.

Si4421

Logic connections between power control bits:

Edge

detector

ebb

enable crystal

oscillator

enable baseband

circuits

enable

RF front end

enable

RF synthesizer

start TX

clear TX latch

enable

power amplifier

VCO and

PLL

Crystal

oscillator

Digital signal

processing

TX latch

enable baseband

circuits

enable

RF front end

enable

power amplifier

enable

RF synthesizer

start TX

clear TX latch

enable

crystal oscillator

clock and data out

I/Q

demod

Note:

 If both et and er bits are set the chip goes to receive mode.

 FSK / nFFS input are equipped with internal pull-up resistor. To achieve minimum current consumption do not pull this input

to logic low in sleep mode.

 To enable the RF synthesizer, the crystal oscillator must be turned on

 To turn on the baseband circuits, the RF synthesizer (and this way the crystal oscillator) must be enabled.

 Setting the er bit automatically turns on the crystal oscillator, the synthesizer, the baseband circuits and the RF fronted.

 Setting the et bit automatically turns on the crystal oscillator, the synthesizer and the RF power amplifier.

Clock tail feature: When the clock output (pin 8) used to provide clock signal for the microcontroller (dc bit is set to 0), it is possible

to use the clock tail feature. This means that the crystal oscillator turn off is delayed, after issuing the command (clearing the ex bit)

192 more clock pulses are provided. This ensures that the microcontroller can switch itself to low power consumption mode. In order

to use this feature, a Status Read Command (page 27) must be issued before the ex bit set to zero. If status read was not performed

then the clock output shuts down immediately leaving the microcontroller in unknown state.

Automatic crystal oscillator enable/disable feature: When an interrupt occurs, the crystal oscillator automatically turns on –

regardless to the setting of the ex bit – to supply clock signal to the microcontroller. After clearing all interrupts by handling them

properly (see the Interrupt Handling section, page 28) and performing Status Read Command, the crystal oscillator is automatically

turned off. The clock tail feature provides enough clock pulses for the microcontroller to go to low power mode. Due to this automatic

feature, it is not possible to turn off the crystal by clearing the ex bit if any interrupt is active. For example, after power on the POR

interrupt must be cleared by a status read then writing zero to the ex bit will put the part into sleep mode. Very important to clear all

interrupts before turning the ex bit off because the extra current required by running crystal oscillator can shorten the battery life

significantly.

Disabling the clock output (bit dc=1) turns off both the clock tail and the automatic crystal oscillator enable/disable feature, only the

ex bit controls the crystal oscillator (supposing that both the er and et bits are cleared), the interrupts have no effect on it.

Si4421

3. Frequency Setting Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 0 1 0 f11 f10 f9 f8 f7 f6 f5 f4 f3 f2 f1 f0 A680h

The 12-bit parameter F (bits f11 to f0) should be in the range

of 96 and 3903. When F value sent is out of range, the

previous value is kept. The synthesizer center frequency f0

can be calculated as:

f0 = 10 · C1 · (C2 + F/4000) [MHz]

The constants C1 and C2 are determined by

the selected band as:

Band

[

MHz

]

C1 C2

433 1 43

868 2 43

915 3 30

Band Minimum Fre

uenc

Maximum Fre

uenc

PLL Fre

uenc

Ste

433 MHz 430.2400 MHz 439.7575 MHz 2.5 kHz

868 MHz 860.4800 MHz 879.5150 MHZ 5.0 kHz

915 MHz 900.7200 MHz 929.2725 MHz 7.5 kHz

4. Data Rate Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 0 1 1 0 cs r6 r5 r4 r3 r2 r1 r0 C623h

The actual bit rate in transmit mode and the expected bit rate of the received data stream in receive mode is determined by the 7-bit

parameter R (bits r6 to r0) and bit cs.

BR = 10000 / 29 / (R+1) / (1+cs · 7) [kbps]

In the receiver set R according to the next function:

R= (10000 / 29 / (1+cs · 7) / BR) – 1, where BR is the expected bit rate in kbps.

Apart from setting custom values, the standard bit rates from 600 bps to 115.2 kbps can be approximated with small error.

Data rate accuracy requirements:

Clock recovery in slow mode: BR/BR < 1/(29 · Nbit) Clock recovery in fast mode: BR/BR < 3/(29 · Nbit)

BR is the bit rate set in the receiver and BR is the bit rate difference between the transmitter and the receiver. Nbit is the maximum

number of consecutive ones or zeros in the data stream. It is recommended for long data packets to include enough 1/0 and 0/1

transitions, and to be careful to use the same division ratio in the receiver and in the transmitter.

5. Receiver Control Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 0 0 1 0 p16 d1 d0 i2 i1 i0 g1 g0 r2 r1 r0 9080h

Bit 10 (p16): Pin 16 function select

p16 Function of pin 16

0 Interrupt input

1 VDI output

Si4421

Bits 9-8 (d1 to d0): VDI (valid data indicator) signal response time setting:

d1 d0 Response

0 0 Fast

0 1 Medium

1 0 Slow

1 1 Always on

VDI Logic Diagram:

R/S FF

LOGIC HIGH

d1CR_LOCK

DRSSI

DQD

IN0

IN1

IN2

IN3

SEL1

SEL0

DQD

CR_LOCK

DQD

DRSSI

SET

CLR

VDI

MUX

FAST

MEDIUM

SLOW

er *

CLR

Note:

* For details see the Power Management Command

Slow mode: The VDI signal will go high only if the DRSSI, DQD and the CR_LOCK (Clock Recovery Locked) signals present at the same

time. It stays high until any of the abovementioned signals present; it will go low when all the three input signals are low.

Medium mode: The VDI signal will be active when the CR_LOCK signal and either the DRSSI or the DQD signal is high. The valid data

indicator will go low when either the CR_LOCK gets inactive or both of the DRSSI or DQD signals go low.

Fast mode: The VDI signal follows the level of the DQD signal.

Always mode: VDI is connected to logic high permanently. It stays always high independently of the receiving parameters.

Bits 7-5 (i2 to i0): Receiver baseband bandwidth (BW) select:

i2 i1 i0 BW [kHz]

0 0 0 Reserved

0 0 1 400

0 1 0 340

0 1 1 270

1 0 0 200

1 0 1 134

1 1 0 67

1 1 1 Reserved

Note: For the optimal bandwidth settings at different data rates see the table on page 37.

Si4421

Bits 4-3 (g1 to g0): LNA gain select:

g1 g0 Gain relative to maximum [dB]

0 0 0

0 1 -6

1 0 -14

1 1 -20

Bits 2-0 (r2 to r0): RSSI detector threshold:

r2 r1 r0 RSSIsetth

0 0 0 -103

0 0 1 -97

0 1 0 -91

0 1 1 -85

1 0 0 -79

1 0 1 -73

1 1 0 Reserved

1 1 1 Reserved

The RSSI threshold depends on the LNA gain, the real RSSI threshold can be calculated:

RSSIth =RSSIsetth+GLNA

6. Data Filter Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 0 0 1 0 al ml 1 s 1 f2 f1 f0 C22Ch

Bit 7 (al): Clock recovery (CR) auto lock control

1: auto mode: the CR starts in fast mode, after locking it switches to slow mode. Bit 6 (ml) has no effect.

0: manual mode, the clock recovery mode is set by Bit 6 (ml)

Bit 6 (ml): Clock recovery lock control

1: fast mode, fast attack and fast release (4 to 8-bit preamble (1010...) is recommended)

0: slow mode, slow attack and slow release (12 to 16-bit preamble is recommended)

Using the slow mode requires more accurate bit timing (see Data Rate Command, page 17).

Bit 4 (s): Select the type of the data filter:

s Filter Type

0 Digital filter

1 Analog RC filter

Digital: This is a digital realization of an analog RC filter followed by a comparator with hysteresis. The time

constant is automatically adjusted to the bit rate defined by the Data Rate Command (page 17).

Note: Bit rate cannot exceed 115 kpbs in this mode.

Analog RC filter: The demodulator output is fed to pin 7 over a 10 kOhm resistor. The filter cut-off frequency is set

by the external capacitor connected to this pin and VSS.

The table shows the optimal filter capacitor values for different data rates

Data Rate [kbps] 1.2 2.4 4.8 9.6 19.2 38.4 57.6 115.2 256

Filter Capacitor Value 12 nF 8.2 nF 6.8 nF 3.3 nF 1.5 nF 680 pF 270 pF 150 pF 100 pF

Note: If analog RC filter is selected the internal clock recovery circuit and the FIFO cannot be used.

Si4421

Bits 2-0 (f2 to f0): DQD threshold parameter.

The Data Quality Detector is a digital processing part of the radio, connected to the demodulator - it is an indicator

reporting the reception of an FSK modulated RF signal. It will work every time the receiver is on. Setting this

parameter defines how clean incoming data stream would be stated as good data (valid FSK signal).

If the internally calculated data quality value exceeds the DQD threshold parameter for five consecutive data bits

for both the high and low periods, then the DQD signal goes high.

The DQD parameter in the Data Filter Command should be chosen according to the following rules:

 The DQD parameter can be calculated with the following formula:

DQDpar = 4 x (deviation – TX-RXoffset) / bit rate

 It should be larger than 4 because otherwise noise might be treated as a valid FSK signal

 The maximum value is 7.

7. FIFO and Reset Mode Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 1 0 1 0 f3 f2 f1 f0 sp al ff dr CA80h

Bits 7-4 (f3 to f0): FIFO IT level. The FIFO generates IT when the number of received data bits reaches this level.

Bit 3 (sp): Select the length of the synchron pattern:

sp Byte1 Byte0 (POR) Synchron Pattern (Byte1+Byte0)

0 2Dh D4h 2DD4h

1 Not used D4h D4h

Note: The synchron pattern consists of one or two bytes depending on the sp bit. Byte1 is fixed 2Dh, Byte0 can be programmed by

the Synchron Pattern Command (page 21).

Bit 2 (al): Set the input of the FIFO fill start condition:

al FIFO fill start condition

0 Synchron pattern

1 Always fill

Si4421

Bit 1 (ff): FIFO fill will be enabled after synchron pattern reception. The FIFO fill stops when this bit is cleared.

Bit 0 (dr): Disables the highly sensitive RESET mode.

dr Reset mode Reset triggered when

0 Sensitive reset Vdd below 1.6V, Vdd glitch greater than 600mV

1 Non-sensitive reset Vdd below 250mV

Note: To restart the synchron pattern recognition, bit 1 (ef, FIFO fill enable) should be cleared and set.

8. Synchron Pattern Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 1 1 1 0 b7 b6 b5 b4 b3 b2 b1 b0 CED4h

The Byte0 of the synchron pattern (see FIFO and Reset Mode command, page 20) can be reprogrammed by B <b7:b0>.

9. Receiver FIFO Read Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 B000h

With this command, the controller can read 8 bits from the receiver FIFO. Bit 6 (ef) must be set in Configuration Setting Command

(page 15).

Note: During FIFO access fSCK cannot be higher than fref /4, where fref is the crystal oscillator frequency. When the duty-cycle of the

clock signal is not 50 % the shorter period of the clock pulse width should be at least 2/fref .

10. AFC Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 0 1 0 0 a1 a0 rl1 rl0 st fi oe en C4F7h

Bit 7-6 (a1 to a0): Automatic operation mode selector:

a1 a0 Operation mode

0 0 Auto mode off (Strobe is controlled by microcontroller)

0 1 Runs only once after each power-up

1 0 Keep the foffset only during receiving (VDI=high)

1 1 Keep the foffset value independently from the state of the VDI signal

Si4421

Bit 5-4 (rl1 to rl0): Range limit. Limits the value of the frequency offset register to the next values:

rl1 rl0 Max deviation

0 0 No restriction

0 1 +15 fres to -16 fres

1 0 +7 fres to -8 fres

1 1 +3 fres to -4 fres

fres:

433 MHz bands: 2.5 kHz

868 MHz band: 5 kHz

915 MHz band: 7.5 kHz

Bit 3 (st): Strobe edge, when st goes to high, the actual latest calculated frequency error is stored into the offset register of

the AFC block.

Bit 2 (fi): Switches the circuit to high accuracy (fine) mode. In this case, the processing time is about twice as long, but the

measurement uncertainty is about half.

Bit 1 (oe): Enables the frequency offset register. It allows the addition of the offset register to the frequency control word of

the PLL.

Bit 0 (en): Enables the calculation of the offset frequency by the AFC circuit.

In manual mode, the strobe signal is provided by the microcontroller. One measurement cycle (and strobe) signal can compensate

about 50-60% of the actual frequency offset. Two measurement cycles can compensate 80%, and three measurement cycles can

compensate 92%. The ATGL bit in the status register can be used to determine when the actual measurement cycle is finished.

In automatic operation mode (no strobe signal is needed from the microcontroller to update the output offset register) the AFC circuit

is automatically enabled when the VDI indicates potential incoming signal during the whole measurement cycle and the circuit

measures the same result in two subsequent cycles.

Without AFC the transmitter and the receiver needs to be tuned precisely to the same frequency. RX/TX frequency offset can lower

the range. The units must be adjusted carefully during production, stable, expensive crystal must be used to avoid drift or the output

power needs to be increased to compensate yield loss.

The AFC block will calculate the TX-RX offset. This value will be used to pull the RX synthesizer close to the frequency of the

transmitter. The main benefits of the automatic frequency control: cheap crystal can be used, the temperature or aging drift will not

cause range loss and no production alignment needed.

Si4421

There are four operation modes:

1. (a1=0, a0=0) Automatic operation of the AFC is off. Strobe bit can be controlled by the microcontroller.

2. (a1=0, a0=1) The circuit measures the frequency offset only once after power up. This way, extended TX-RX distance can be

achieved. In the final application, when the user inserts the battery, the circuit measures and compensates for the frequency offset

caused by the crystal tolerances. This method allows for the use of cheaper quartz in the application and provides protection against

tracking an interferer.

3. (a1=1, a0=0) The frequency offset is calculated automatically and the center frequency is corrected when the VDI is high. The

calculated value is dropped when the VDI goes low. To improve the efficiency of the AFC calculation two methods are recommended:

a. The transmit package should start with a low effective baud rate pattern (i.e.: 00110011) because it is easier to receive. The

circuit automatically measures the frequency offset during this initial pattern and changes the receiving frequency accordingly.

The further part of the package will be received by the corrected frequency settings.

b. The transmitter sends the first part of the packet with a step higher deviation than required during normal operation to ease

the receiving. After the frequency shift was corrected, the deviation can be reduced.

In both cases (3a and 3b), when the VDI indicates poor receiving conditions (VDI goes low), the output register is automatically

cleared. Use this “drop offset” mode when the receiver communicates with more than one transmitter.

4. (a1=1, a0=1) It is similar to mode 3, but suggested to use when a receiver operates with only one transmitter. After a complete

measuring cycle, the measured value is kept independently of the state of the VDI signal. When the receiver is paired with only one

transmitter, it is possible to use this “keep offset” mode. In this case, the DRSSI limit should be selected carefully to minimize the

range hysteresis.

11. TX Configuration Control Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 0 0 1 1 0 0 mp m3 m2 m1 m0 0 p2 p1 p0 9800h

Bits 8-4 (mp, m3 to m0): FSK modulation parameters:

The resulting output frequency can be calculated as:

out = f0 + (-1)SIGN · (M + 1) · (15 kHz)

where:

0 is the channel center frequency (see the

Frequency Setting Command)

M is the four bit binary number <m3 : m0>

SIGN = (mp) XOR FSK

Note: For the optimal FSK modulation settings at different

data rates see the table on page 37.

Bits 2-0 (p2 to p0): Output power:

p2 p1 p0 Relative Output Power [dB]

0 0 0 0

0 0 1 -2.5

0 1 0 -5

0 1 1 -7.5

1 0 0 -10

1 0 1 -12.5

1 1 0 -15

1 1 1 -17.5

Note: The output power given in the table is relative to the

maximum available power, which depends on the

actual antenna impedance. (See: Antenna

Application Note: IA ISM-AN1)

out

fsk

mp=0 and FSK=0

mp=1 and FSK=1 mp=1 and FSK=0

mp=0 and FSK=1

oror

Note: FSK represents the value of the actual data bit.

Si4421

12. PLL Setting Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 1 1 0 0 0 ob1 ob0 1 dly ddit 1 bw0 CC77h

Bits 6-5 (ob1-ob0): Microcontroller output clock buffer rise and fall time control. The ob1-ob0 bits are changing the output drive

current of the CLK pin. Higher current provides faster rise and fall times but can cause interference.

ob1 ob0 Selected

C CLK fre

uenc

1 1 5 or 10 MHz

(

recommended

)

1 0 3.3 MHz

0 X 2.5 MHz or less

Note: Needed for optimization of the RF performance. Optimal settings can vary according to the external load capacitance.

Bit 3 (dly): Switches on the delay in the phase detector when this bit is set.

Bit 2 (ddit): When set, disables the dithering in the PLL loop.

Bit 0 (bw0): PLL bandwidth can be set for optimal TX RF performance.

bw0 Max bit rate

[

]

Phase noise at 1MHz offset

[

dBc/Hz

]

0 86.2 -107

1 256 -102

Note: POR default settings of the register were carefully selected to cover almost all typical applications. When changing these

values, examine thoroughly the output RF spectrum. For more information, contact Silicon Labs Support.

13. Transmitter Register Write Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 0 1 1 1 0 0 0 t7 t6 t5 t4 t3 t2 t1 t0 B8AAh

With this command, the controller can write 8 bits (t7 to t0) to the transmitter data register. Bit 7 (el) must be set in Configuration

Setting Command (page 15).

Multiple Byte Write with Transmit Register Write Command:

nSEL

SCK

SDI

SDO

TX BYTE1 TX BYTEnTX BYTE2

command

T r a n s m i t R e g i s t e r W r i t e

(REGISTER IT

in TX mode*)

Note: *The transceiver is in transmit (TX) mode when bit er is cleared using the Power Management Command

Note: Alternately the transmit register can be directly accessed by nFFS (pin6).

Si4421

14. Wake-Up Timer Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 1 r4 r3 r2 r1 r0 m7 m6 m5 m4 m3 m2 m1 m0 E196h

The wake-up time period can be calculated by (m7 to m0) and (r4 to r0):

Twake-up = 1.03 · M · 2R + 0.5 [ms]

Note:

 For continual operation, the ew bit should be cleared and set at the end of every cycle.

 For future compatibility, use R in a range of 0 and 29.

15. Low Duty-Cycle Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 1 0 0 0 d6 d5 d4 d3 d2 d1 d0 en C80Eh

With this command, autonomous low duty-cycle operation can be set in order to decrease the average power consumption in receive

mode.

Bits 7-1 (d6-d0): The duty-cycle can be calculated by using (d6 to d0) and M. (M is parameter in a Wake-Up Timer Command, see

above). The time cycle is determined by the Wake-Up Timer Command.

duty-cycle= (D · 2 +1) / M · 100%

Bit 0 (en): Enables the low duty-cycle Mode. Wake-up timer interrupt is not generated in this mode.

Note: In this operation mode, bit er must be cleared and bit ew must be set in the Power Management Command (page 15).

In low duty-cycle mode the receiver periodically wakes up for a short period of time and checks if there is a valid FSK transmission in

progress. FSK transmission is detected in the frequency range determined by Frequency Setting Command (page 17) plus and

minus the baseband filter bandwidth determined by the Receiver Control Command (page 17). This on-time is automatically

extended while DQD indicates good received signal condition.

When calculating the on-time take into account:

- the crystal oscillator, the synthesizer and the PLL needs time to start, see the AC Characteristics (Turn-on/Turnaround

timings) on page 11

- depending on the DQD parameter, the chip needs to receive a few valid data bits before the DQD signal indicates good

signal condition (Data Filter Command, page 19)

Choosing too short on-time can prevent the crystal oscillator from starting or the DQD signal will not go high even when the received

signal has good quality.

There is an application proposal on page 26. The Si4421 is configured to work in FIFO mode. The chip periodically wakes up and

switches to receiving mode. If valid FSK data received, the chip sends an interrupt to the microcontroller and continues filling the RX

FIFO. After the transmission is over and the FIFO is read out completely and all other interrupts are cleared, the chip goes back to low

power consumption mode.

Si4421

Application Proposal for LPDM (Low Power Duty-Cycle Mode) Receivers:

16. Low Battery Detector and Microcontroller Clock Divider Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

1 1 0 0 0 0 0 0 d2 d1 d0 0 v3 v2 v1 v0 C000h

The 4-bit parameter (v3 to v0) represents the value V, which defines the threshold voltage Vlb of the detector:

Vlb= 2.25 + V · 0.1 [V]

Clock divider configuration:

d2 d1 d0 Clock Output

Frequency [MHz]

0 0 0 1

0 0 1 1.25

0 1 0 1.66

0 1 1 2

1 0 0 2.5

1 0 1 3.33

1 1 0 5

1 1 1 10

The low battery detector and the clock output can be enabled or disabled by bits eb and dc, respectively, using the Power

Management Command (page 15).

Si4421

17. Status Read Command

Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 POR

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0000h

The read command starts with a zero, whereas all other control commands start with a one. If a read command is identified, the

status bits will be clocked out on the SDO pin as follows:

Status Register Read Sequence with FIFO Read Example:

Bit Name Function

RGIT TX register is ready to receive the next byte (Can be cleared by Transmitter Register Write Command, page 24)

FFIT The number of data bits in the RX FIFO has reached the pre-programmed limit (Can be cleared by any of the

FIFO read methods)

POR Power-on reset (Cleared after Status Read Command)

RGUR TX register under run, register over write (Cleared after Status Read Command)

FFOV RX FIFO overflow (Cleared after Status Read Command)

WKUP Wake-up timer overflow (Cleared after Status Read Command)

EXT Logic level on interrupt pin (pin 16) changed to low (Cleared after St atus Read Command)

LBD Low battery detect, the power supply voltage is below the pre-programmed limit

FFEM FIFO is empty

ATS Antenna tuning circuit detected strong enough RF signal

RSSI The strength of the incoming signal is above the pre-programmed limit

DQD Data quality detector output

CRL Clock recovery locked

ATGL Toggling in each AFC cycle

OFFS(6) MSB of the measured frequency offset (sign of the offset value)

OFFS(3) -OFFS(0) Offset value to be added to the value of the frequency control parameter (Four LSB bits)

Note: In order to get accurate values the AFC has to be disabled during the read by clearing the en bit in the AFC Control Command

(page 21). The AFC offset value (OFFS bits in the status word) is represented as a two’s complement number. The actual

frequency offset can be calculated as the AFC offset value multiplied by the current PLL frequency step (see the Frequency

Setting Command on page 17).

Si4421

INTERRUPT HANDLING

In order to achieve low power consumption there is an advanced event handling circuit implemented. The device has a very low

power consumption mode, so called sleep mode. In this mode only a few parts of the circuit are working. In case of an event, the

device wakes up, switches into active mode and an interrupt signal generated on the nIRQ pin to indicate the changed state to the

microcontroller. The cause of the interrupt can be determined by reading the status word of the device (see Status Read Command,

page 27).

Several interrupt sources are available:

 RGIT – TX register empty interrupt: This interrupt generated when the transmit register is empty. Valid only when the el

(enable internal data register) bit is set in the Configuration Setting Command (page 15), and the transmitter is enabled in

the Power Management command.

 FFIT – the number of bits in the RX FIFO reached the preprogrammed level: When the number of received data bits in the

receiver FIFO reaches the threshold set by the f3…f0 bits of the FIFO and Reset Mode Command (page 20) an interrupt is

fired. Valid only when the ef (enable FIFO mode) bit is set in the Configuration Setting Command and the receiver is enabled

in the Power Management Command (page 15).

 POR – power on reset interrupt: An interrupt generated when the change on the VDD line triggered the internal reset circuit or

a software reset command was issued. For more details, see the Reset Modes section (page 34).

 RGUR –

TX register under run: The automatic baud rate generator finished the transmission of the byte in the TX register

before the register write occurred. Valid only when the el (enable internal data register) bit is set in the Configuration Setting

Command and the transmitter is enabled in the Power Management command.

 FFOV – FIFO overflow: There are more bits received than the capacity of the FIFO (16 bits). Valid only when the ef (enable

FIFO mode) bit is set in the Configuration Setting Command and the receiver is enabled in the Power Management

command

 WKUP – wake-up timer interrupt: This interrupt event occurs when the time specified by the Wake-Up Timer Command (page

25) has elapsed. Valid only when the ew bit is set in the Power Management Command.

 EXT – external interrupt: Follows the level of the nINT pin if it is configured as an external Interrupt pin in the Receiver Control

Command (page 17, p16 bit is cleared).

 LBD – low battery detector interrupt: Occurs when the VDD goes below the programmable low battery detector threshold level

(v3…v0 bits in the Low Battery and Microcontroller Clock Divider Command, page 26). Valid only when the eb (enable low

battery detector) bit is set in the Power Management Command.

If any of the sources becomes active, the nIRQ pin will change to logic low level, and the corresponding bit in the status byte will be

HIGH.

Clearing an interrupt actually implies two things:

 Releasing the nIRQ pin to return to logic high

 Clearing the corresponding bit in the status byte

This may be completed with the following interrupt sources:

 RGIT: both the nIRQ pin and status bit remain active until the register is written (if under-run does not occur until the register

write), or the transmitter and the TX latch are switched off.

 FFIT: both the nIRQ pin and status bit remain active until the FIFO is read (a FIFO IT threshold number of bits have been

read), the receiver is switched off, or the RX FIFO is switched off.

 POR: both the nIRQ pin and status bit can be cleared by the read status command

 RGUR: this bit is always set together with RGIT; both the nIRQ pin and the status bit remain active until the transmitter and

the TX latch is switched off.

 FFOV: this bit is always set together with FFIT; it can be cleared by the status read command, but the FFIT bit and hence the

nIRQ pin will remain active until the FIFO is read fully, the receiver is switched off, or the RX FIFO is switched off.

 WKUP: both the nIRQ pin and status bit can be cleared by the read status command

 EXT: both the nIRQ pin and status bit follow the level of the nINT pin

 LBD: the nIRQ pin can be released by the reading the status, but the status bit will remain active while the VDD is below the

threshold.

Si4421

The best practice in interrupt handling is to start with a status read when interrupt occurs, and then make a decision based on the

status byte. It is very important to mention that any interrupt can “wake-up” the EZradio chip from sleep mode. This means that the

crystal oscillator starts to supply clock signal to the microcontroller even if the microcontroller has its own clock source. Also, the

Si4421 will not go to low current sleep mode if any interrupt remains active regardless to the state of the ex (enable crystal

oscillator) bit in the Power Management Command (page 15). This way the microcontroller always can have clock signal to process

the interrupt. To prevent high current consumption and this way short battery life, it is strongly advised to process and clear every

interrupt before going to sleep mode. All unnecessary functions should be turned off to avoid unwanted interrupts. Before freezing

the microcontroller code, a thorough testing must be performed in order to make sure that all interrupt sources are handled before

putting the radio device to low power consumption sleep mode. If the dc bit is set in the Power Management Command, then only

the ex bit controls the crystal oscillator (supposing that both the er and et bits are cleared), the interrupts have no effect on it.

TX REGISTER BUFFERED DATA TRANSMISSION

In this operating mode (enabled by bit el, in the Configuration Setting Command, page 15) the TX data is clocked into one of the two

8-bit data registers. The transmitter starts to send out the data from the first register (with the given bit rate) when bit et is set with

the Power Management Command (page 15). The initial value of the data registers (AAh) can be used to generate preamble. During

this mode, the SDO pin can be monitored to check whether the register is ready (SDO is high) to receive the next byte from the

microcontroller.

TX register simplified block diagram (before transmit)

TX register simplified block diagram (during transmit)

Si4421

Typical TX register usage

et bit

(enable transmitter)

TX data

SPI commands

(nSEL, SCK, SDI)

enable

Synthesizer / PA PASynt.

nIRQ

SDO**

et = 1

Power Man

0xAA

TX latch wr

TX byte1

0xAA

Notes:

*Ttx_XTAL_ON is the start-up time of the PLL + PA with running crystal oscillator

** SDO is tri-state if nSEL is logic high.

et = 0

Power Man

Conf. Set.

el = 1

Ttx_XTAL_ON*

Fraction of the

Dummy byte

TX latch wr

Dummy

TX byte

Do not switch the et off here, because the

TX byte1 is not transmitted out

only stored into the internal register!

el = 0

Conf. Set.

Enabling the Transmitter preloads the TX

latch with 0xAAAA

Note: The content of the data registers are initialized by clearing bit et.

A complete transmit sequence should be performed as follows:

a. Enable the TX register by setting the el bit to 1 (Configuration Setting Command, page 15)

b. The TX register automatically filled out with 0xAAAA, which can be used to generate preamble.

c. Enable the transmitter by setting the et bit (Power Management Command, page 15)

d. The synthesizer and the PLL turns on, calibrates itself then the power amplifier automatically enabled

e. The TX data transmission starts

f. When the transmission of the byte completed, the nIRQ pin goes high, the SDO pin goes low at the same time. The nIRQ

pulse shows that the first 8 bits (the first byte, by default 0xAA) has transmitted. There are still 8 bits in the transmit

g. The microcontroller recognizes the interrupt and writes a data byte to the TX register

h. Repeat f. - g. until the last data byte reached

i. Using the same method, transmit a dummy byte. The value of this dummy byte can be anything.

j. The next high to low transition on the nIRQ line (or low to high on the SDO pin) shows that the transmission of the data

bytes ended. The dummy byte is still in the TX latch.

k. Turn off the transmitter by setting the et bit to 0. This event will probably happen while the dummy byte is being

transmitted. Since the dummy byte contains no useful information, this corruption will cause no problems.

l. Clearing the el bit clears the Register Underrun interrupt; the nIRQ pin goes high, the SDO low.

It is possible to perform this sequence without sending a dummy byte (step i.) but after loading the last data byte to the transmit

register the PA turn off should be delayed for at least 16 bits time. The clock source of the microcontroller (if the clock is not supplied

by the Si4421) should be stable enough over temperature and voltage to ensure this minimum delay under all operating

circumstances.

When the dummy byte is used, the whole process is driven by interrupts. Changing the TX data rate has no effect on the algorithm

and no accurate delay measurement is needed.

Si4421

RX FIFO BUFFERED DATA READ

In this operating mode, incoming data are clocked into a 16-bit FIFO buffer. The receiver starts to fill up the FIFO when the Valid Data

Indicator (VDI) bit and the synchron pattern recognition circuit indicates potentially real incoming data. This prevents the FIFO from

being filled with noise and overloading the external microcontroller.

Interrupt Controlled Mode:

The user can define the FIFO IT level (the number of received bits) which will generate the nFFIT when exceeded. The status bits

report the changed FIFO status in this case.

Polling Mode:

When nFFS signal is low the FIFO output is connected directly to the SDO pin and its content can be clocked out by the SCK. Set the

FIFO IT level to 1. In this case, as long as FFIT indicates received bits in the FIFO, the controller may continue to take the bits away.

When FFIT goes low, no more bits need to be taken.

An SPI read command is also available to read out the content of the FIFO (Receiver FIFO Read Command, page 21).

FIFO Read Example with FFIT Polling

nSEL

SCK

nFFS

SDO

01234

FO+1 FO+2FIFO OUT FO+4FO+3

FIFO read out

FFIT

Note: During FIFO access fSCK cannot be higher than fref /4, where fref is the crystal oscillator frequency. When the duty-cycle of the

clock signal is not 50% the shorter period of the clock pulse should be at least 2/fref .

RECOMMENDED PACKET STRUCTURES

Preamble Synch r on word

(Can be network ID) Payload CRC

Minimum length 4 - 8 bits (1010b or 0101b) D4h (programmable) ? 4 bit - 1 byte

Recommended length 8 -12 bits (e.g. AAh or 55h) 2DD4h (D4 is programmable) ? 2 byte

Si4421

CRYSTAL SELECTION GUIDELINES

The crystal oscillator of the Si4421 requires a 10 MHz parallel mode crystal. The circuit contains an integrated load capacitor in

order to minimize the external component count. The internal load capacitance value is programmable from 8.5 pF to 16 pF in 0.5

pF steps. With appropriate PCB layout, the total load capacitance value can be 10 pF to 20 pF so a variety of crystal types can be

used.

When the total load capacitance is not more than 20 pF and a worst case 7 pF shunt capacitance (C0) value is expected for the

crystal, the oscillator is able to start up with any crystal having less than 100 ohms ESR (equivalent series loss resistance). However,

lower C0 and ESR values guarantee faster oscillator startup.

The crystal frequency is used as the reference of the PLL, which generates the local oscillator frequency (fLO ). Therefore, fLO is

directly proportional to the crystal frequency. The accuracy requirements for production tolerance, temperature drift and aging can

thus be determined from the maximum allowable local oscillator frequency error.

Whenever a low frequency error is essential for the application, it is possible to “pull” the crystal to the accurate frequency by

changing the load capacitor value. The widest pulling range can be achieved if the nominal required load capacitance of the crystal is

in the “midrange”, for example 16 pF. The “pull-ability” of the crystal is defined by its motional capacitance and C0.

Maximum XTAL Tolerances Including Temperature and Aging [ppm]

Bit Rate: 2.4 kbps

Deviation [± kHz]

30 45 60 75 90 105 120

433 MHz 20 30 50 70 90 100 100

868 MHz 10 20 25 30 40 50 60

915 MHz 10 15 25 30 40 50 50

Bit Rate: 9.6 kbps

Deviation [± kHz]

30 45 60 75 90 105 120

433 MHz 15 30 50 70 80 100 100

868 MHz 8 15 25 30 40 50 60

915 MHz 8 15 25 30 40 50 50

Bit Rate: 38.4 kbps

Deviation [± kHz]

30 45 60 75 90 105 120

433 MHz don't use 5 20 30 50 75 75

868 MHz don't use 3 10 20 25 30 40

915 MHz don't use 3 10 15 25 30 40

Bit Rate: 115.2 kbps

Deviation [± kHz]

105 120 135 150 165 180 195

433 MHz don't use 3 20 30 50 70 80

868 MHz don't use don't use 10 20 25 35 45

915 MHz don't use don't use 10 15 25 30 40

Si4421

RX-TX ALIGNMENT PROCEDURES

RX-TX frequency offset can be caused only by the differences in the actual reference frequency. To minimize these errors it is

suggested to use the same crystal type and the same PCB layout for the crystal placement on the RX and TX PCBs.

To verify the possible RX-TX offset it is suggested to measure the CLK output of both chips with a high level of accuracy. Do not

measure the output at the XTL pin since the measurement process itself will change the reference frequency. Since the carrier

frequencies are derived from the reference frequency, having identical reference frequencies and nominal frequency settings at the

TX and RX side there should be no offset if the CLK signals have identical frequencies.

It is possible to monitor the actual RX-TX offset using the AFC status report included in the status byte of the receiver. By reading out

the status byte from the receiver, the actual measured offset frequency will be reported. In order to get accurate values the AFC has

to be disabled during the read by clearing the en bit in the AFC Control Command (page 21).

Si4421

RESET MODES

The chip will enter into reset mode if any of the following conditions are met:

 Power-on reset: During a power up sequence until the Vdd has reached the correct level and stabilized

 Power glitch reset: Transients present on the Vdd line

 Software reset: Special control command received by the chip

Power-on reset

After power up the supply voltage starts to rise from 0V. The reset block has an internal ramping voltage reference (reset-ramp

signal), which is rising at 100mV/ms (typical) rate. The chip remains in reset state while the voltage difference between the actual

Vdd and the internal reset-ramp signal is higher than the reset threshold voltage, which is 600 mV (typical). As long as the Vdd voltage

is less than 1.6V (typical) the chip stays in reset mode regardless the voltage difference between the Vdd and the internal ramp

signal.

The reset event can last up to 100ms supposing that the Vdd reaches 90% its final value within 1ms. During this period, the chip

does not accept control commands via the serial control interface.

Power-on reset example:

Power glitch reset

The internal reset block has two basic mode of operation: normal and sensitive reset. The default mode is sensitive, which can be

changed by the appropriate control command (see Related control commands at the end of this section). In normal mode the power

glitch detection circuit is disabled.

There can be spikes or glitches on the Vdd line if the supply filtering is not satisfactory or the internal resistance of the power supply

is too high. In such cases if the sensitive reset is enabled an (unwanted) reset will be generated if the positive going edge of the Vdd

has a rising rate greater than 100mV/ms and the voltage difference between the internal ramp signal and the Vdd reaches the reset

threshold voltage (600 mV). Typical case when the battery is weak and due to its increased internal resistance a sudden decrease of

the current consumption (for example turning off the power amplifier) might lead to an increase in supply voltage. If for some reason

the sensitive reset cannot be disabled step-by-step decrease of the current consumption (by turning off the different stages one by

one) can help to avoid this problem.

Any negative change in the supply voltage will not cause reset event unless the Vdd level reaches the reset threshold voltage (250mV

in normal mode, 1.6V in sensitive reset mode).

If the sensitive mode is disabled and the power supply turned off the Vdd must drop below 250mV in order to trigger a power-on reset

event when the supply voltage is turned back on. If the decoupling capacitors keep their charges for a long time it could happen that

no reset will be generated upon power-up because the power glitch detector circuit is disabled.

Note that the reset event reinitializes the internal registers, so the sensitive mode will be enabled again.

Si4421

Sensitive Reset Enabled, Ripple on Vdd:

time

Vdd Reset threshold voltage

(600mV)

nRes

output

1.6V

Reset ramp line

(100mV/ms)

Sensitive reset disabled:

time

Vdd

Reset threshold voltage

(600mV)

nRes

output

250mV

Reset ramp line

(100mV/ms)

Software reset

Software reset can be issued by sending the appropriate control command (described at the end of the section) to the chip. The

result of the command is the same as if power-on reset was occurred but the length of the reset event is much less, 0.25ms typical.

The software reset works only when the sensitive reset mode is selected.

Vdd line filtering

During the reset event (caused by power-on, fast positive spike on the supply line or software reset command), it is very important to

keep the Vdd line as smooth as possible. Noise or periodic disturbing signal superimposed the supply voltage may prevent the part

getting out from reset state. To avoid this phenomenon use adequate filtering on the power supply line to keep the level of the

disturbing signal below 100mVp-p in the DC – 50kHz range for 200ms from Vdd ramp start.. Typical example when a switch-mode

regulator is used to supply the radio, switching noise may be present on the Vdd line. Follow the manufacturer’s recommendations

how to decrease the ripple of the regulator IC and/or how to shift the switching frequency.

Related control commands

FIFO and Reset Mode Command (page 20)

Setting bit<0> to high will change the reset mode to normal from the default sensitive.

SW Reset Command

Issuing FE00h command will trigger software reset (sensitive reset mode must be enabled). See the Wake-up Timer

Command (page 25).

Si4421

TYPICAL PERFORMANCE CHARACTERISTICS

Channel Selectivity and Blocking:

0123456789101112

CW interferer offset from carrier [MHz]

434 MHz

868 MHz

ETSI

Note:

 LNA gain maximum, filter bandwidth 67 kHz, data rate 9.6 kbps, AFC switched off, FSK deviation ± 45 kHz, Vdd = 2.7 V

 Measured according to the descriptions in the ETSI Standard EN 300 220-1 v2.1.1 (2006-01 Final Draft), section 9

 The ETSI limit given in the figure is drawn by taking -106dBm at 9.6kbps typical sensitivity into account, and corresponds to

receiver class 2 requirements (section 4.1.1)

Phase Noise Performance in the 433, 868 and 915 MHz Bands:

433 MHz

868 MHz

915 MHz

(Measured under typical conditions: Top = 27 oC; Vdd = Voc = 2.7 V)

Si4421

BER Curves in 433 MHz Band:

10-6

10-5

10-4

10-3

10-2

10-1

1.2k

2.4k

4.8k

9.6k

19.2k

38.4k

57.6k

115.2k

-120 -115 -110 -105 -100 -95 -90

BER Curves in 868 MHz Band:

10-6

10-5

10-4

10-3

10-2

10-1

1.2k

2.4k

4.8k

9.6k

19.2k

38.4k

57.6k

115.2k

-115 -110 -105 -100 -95 -90 -85

The table below shows the optimal receiver baseband bandwidth (BW) and transmitter deviation frequency (δfFSK ) settings for

different data-rates supposing no transmit receive offset frequency. If TX/RX offset (for example due to crystal tolerances) have to be

taken into account, increase the BW accordingly.

1.2 kbps 2.4 kbps 4.8 kbps 9.6 kbps 19.2 kbps 38.4 kbps 57.6 kbps 115.2 kbps

BW=67 kHz

fFSK =45 kHz

BW=67 kHz

fFSK =45 kHz

BW=67 kHz

fFSK =45kHz

BW=67 kHz

fFSK =45 kHz

BW=67 kHz

fFSK =45 kHz

BW=134 kHz

fFSK =90 kHz

BW=134 kHz

fFSK =90 kHz

BW=200 kHz

fFSK =120 kHz

Si4421

Receiver Sensitivity over Ambient Temperature (433 MHz, 2.4 kbps,



fFSK: 45 kHz, BW: 67 kHz):

434 MHz

-115

-112

-109

-106

-103

-100

-50-25 0 255075100

Celsius

dBm

2.2V

2.7V

3.3V

3.8V

Receiver Sensitivity over Ambient Temperature (868 MHz, 2.4 kbps,



fFSK: 45 kHz, BW: 67 kHz):

868 MHz

-115

-112

-109

-106

-103

-100

-50 -25 0 25 50 75 100

Celsius

dBm

2.2V

2.7V

3.3V

3.8V

Si4421

REFERENCE DESIGNS

Evaluation Board with 50 Ohm Matching Network

Schematics

CLK_OUT

ARSSI

C10

C9 C11

L1L4

* See values in the table

optional

C3 C2

SDI

SCK

NSEL

SDO

NIRQ

FSK/DATA/NFFS

DCLK/CFIL/FFIT

NINT/VDI 16

XTL/REF 9

CLK

VSS 11

RF2 12

RF1 13

VDD 14

ARSSI 15

NRES 10

IC1

TP61

CN62

CN61

TP62

Q61

MATCHING_NETWORK

VDD

GND

ARSSI

RESET

SDI

SCK

SEL

SDO

IRQ

DATA

DCLK

VDI

10nF

GND

VDD

4.7nF

GND

2.2uF

GND

IA4421

VDD

GND

VDD

10MHz

GND

Frequency Dependent Component Values

f [MHz] L1 [nH] L2 [nH] L3 [nH] L4 [nH] C8 [pF] C9 [pF] C10 [pF] C11 [pF] C3 [pF]

434 18 47 390 18 5 2.7 2.7 220 220

868 3.9 18 100 3.9 2.7 1.2 1.8 47 47

915 3.6 16 100 3.6 2.7 1.2 1.8 33 33

Recommended Component Types

Part number

Component Manufacturer 434MHz 868 MHz 915MHz Note

L1 Coilcraft 0603CS-18NX 0603CS-3N9X 0603CS-3N9X 1

L4 Coilcraft 0603CS-18NX 0603CS-3N9X 0603CS-3N9X 1

L2 Coilcraft 0603CS-47NX 0603CS-18NX 0603CS-16NX 1

L3 Coilcraft 0603CS-R39X 0603CS-R10X 0603CS-R10X 2

C9 Murata GRM1885C1H2R7CZ01B GRM1885C1H1R2CZ01B GRM1885C1H1R2CZ01B 3

C8 Murata GRM1885C1H5R0CZ01B GRM1885C1H2R7CZ01B GRM1885C1H2R7CZ01B 3

C10 Murata GRM1885C1H2R7CZ01B GRM1885C1H1R8CZ01B GRM1885C1H1R8CZ01B 3, 4

C11 Murata GRM1885C1H221JA01B GRM1885C1H470JZ01B GRM1885C1H330JZ01B 3

C3 Murata GRM1885C1H221JA01B GRM1885C1H470JZ01B GRM1885C1H330JZ01B 3

For component selection guidelines, see the notes on the next page.

Si4421

Notes:

1. SRF, DCR and Q should be similar if components from other manufacturer used

2. The SRF should be twice as much as the operation frequency

3. The dielectric type should be C0G and the resonant frequency should be similar if components from alternative vendor used.

4. The values are valid for 1.5mm thick FR4 PCB. If thinner board used the capacitor value should be increased (and vice versa)

to minimize the level of the second harmonic components.

PCB Layout

Top View

Bottom View

Si4421

Evaluation Board with Resonant PCB Antenna (BIFA)

Schematics

* See values in the table

910

11 12

13 14

15 16

17 18

19 20

21 22

23 24

25 26

27 28

29 30

31 32

33 34

35 36

37 38

39 40

CS1

C3 C2

ARSSI

TP1

FFS/DATA

SEL

SCK

SDI

SDO

IRQ

FFE

VDI

JP1

TP3

SDI

SCK

NSEL

SDO

NIRQ

FSK/DATA/NFFS

DCLK/CFIL

NINT/VDI 16

XTL/REF 9

CLK

VSS 11

RF2 12

RF1 13

VDD 14

ARSSI 15

NRES 10

IC1

CLK_OUT

ARSSI

RESET

SDI

SCK

SEL

SDO

IRQ

DATA

DATA DCLK

DCLK

DTO

CLKIN

VDI

CON40-0 100pF

10nF

GND

10MHz

VDD

10nF

GND

2.2uF

GND

IA4421

10k

100k

10k

Note: Components R5 to R8 and C6 are needed for connection to the ISM Chipset Development Kit load board (IA ISM-DK3) and are

not necessary in an application.

Frequency Dependent Component Values

Band C3 [pF] L1 [nH]

868 MHz 47 22

Dual (868/915 MHz) 47/33 18

915 MHz 33 15

Si4421

PCB Layout (Antenna designed for 868/915 MHz band)

Top View

Bottom View

Si4421

PACKAGE INFORMATION

16-pin TSSOP

Detail “A””

Gauge Plane

0. 2 5

Section B-B

See Detail “A”

Min. Nom. Max. Min. Nom. Max.

740,002,1A

600,0200,051,050,01A

A2 0,80 0,90 1,05 0,031 0,035 0,041

210,0700,003,091,0b

b1 0,19 0,22 0,25 0,007 0,009 0,010

800,0400,002,090,0c

600,0400,061,090,01c

D 4,90 5,00 5,10 0,193 0,197 0,201

E1 4,30 4,40 4,50 0,169 0,173 0,177

L 0,50 0,60 0,75 0,020 0,024 0,030

400,090,0R

400,090,01R

80801

Symbol Dimensions in mm Dimensions in Inches

.CSB620.0.CSB56.0

6.40 BSC.

12 REF.

1.00 REF.

0.252 BSC.

0.39 REF.

Si4421