FSDM311 Green Mode Fairchild Power Switch (FPSTM) Features Description Internal Avalanche Rugged SenseFET Precision Fixed Operating Frequency (67KHz) Advanced Burst-Mode Operation (power consumption The FSDM311, consisting of integrated Pulse-Width Modulator (PWM) and SenseFET, is specifically designed for high-performance, off-line Switch Mode Power Supplies (SMPS) with minimal external components. This device is an integrated high-voltage, power-switching regulator which combines a VDMOS SenseFET with a voltage mode PWM control block. The integrated PWM controller features include: a fixed oscillator, Under-Voltage Lockout (UVLO) protection, Leading Edge Blanking (LEB), an optimized gate turnon/turn-off driver, Thermal Shutdown (TSD) protection, and temperature-compensated, precision-current sources for loop-compensation and fault-protection circuitry. When compared to a discrete MOSFET and controller or RCC switching converter solution, the FSDM311 device reduces total component count and design size and weight; while increasing efficiency, productivity, and system reliability. This device provides a basic platform that is well suited for the design of costeffective flyback converters. < 0.1W at 265VAC, no-load condition) Internal Start-up Circuit Pulse-by-Pulse Current Limit Over-Voltage Protection (OVP) Over-Load Protection (OLP) Internal Thermal Shutdown Function (TSD) Auto-Restart Mode Under-Voltage Lockout (UVLO) with Hysteresis Built-in Soft-Start Applications Charger & Adapter for Mobile Phone, PDA & MP3 Auxiliary Power for White Goods, PC, C-TV & Monitor Related Application Notes AN-4137, AN-4141, AN-4147 (Flyback) AN-4134 (Forward) AN-4138 (Charger) Ordering Information Product Number Package Marking Code BVDSS fOSC RDS (ON) FSDM311 8DIP DM311 650V 67KHz 14 FSDM311L 8LSOP DM311 650V 67KHz 14 FPSTM is a trademark of Fairchild Semiconductor Corporation. (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 www.fairchildsemi.com FSDM311 Green Mode Fairchild Power Switch (FPSTM) July 2006 OUTPUT POWER TABLE Product Open Frame(1) 230VAC15%(2) 85~265VAC FSDM311 13W 8W FSDM311L 13W 8W Notes: 1. Maximum practical continuous power in open-frame design with sufficient drain pattern as a heat sink, at 50C ambient. 2. 230VAC or 100/115VAC with doubler. Figure 1 Typical Flyback Application Internal Block Diagram FSDM311 Green Mode Fairchild Power Switch (FPSTM) Typical Application & Output Power Table Figure 2 Functional Block Diagram of FSDM311 (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 2 www.fairchildsemi.com Figure 3 Pin Configuration (Top View) Pin Definitions Pin Number Pin Name 1 GND 2 VCC 3 Vfb 4 NC 5 Vstr 6,7,8 Drain (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 Pin Function Description Ground. SenseFET source terminal on primary side and internal control ground. Positive supply voltage input. Although connected to an auxiliary transformer winding, current is supplied from pin 5 (Vstr) via an internal switch during start-up (see Internal Block Diagram section). When VCC reaches the UVLO upper threshold (9V), the internal start-up switch opens and device power is supplied by the auxiliary transformer winding. Feedback. Inverting input to the PWM comparator with its normal input level between 0.5V and 2.5V. It has a 0.4mA current source connected internally, while a capacitor and opto-coupler are typically connected externally. A feedback voltage of 4.5V triggers overload protection (OLP). There is a time delay while charging the external capacitor Cfb from 3V to 4.5V using an internal 5A current source. This time delay prevents false triggering under transient conditions, but allows the protection mechanism to operate under true overload conditions. No Connection. Start-up. This pin connects directly to the rectified AC line voltage source. At start-up, the internal switch supplies internal bias and charges an external storage capacitor placed between the VCC pin and ground. Once the VCC reaches 9V, the internal switch stops charging the capacitor. SenseFET Drain. The drain pins are designed to connect directly to the primary lead of the transformer and are capable of switching a maximum of 650V. Minimizing the length of the trace connecting these pins to the transformer is recommended to decrease leakage inductance. 3 FSDM311 Green Mode Fairchild Power Switch (FPSTM) Pin Assignments www.fairchildsemi.com The "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. TA=25C, unless otherwise specified. Symbol VDRAIN VSTR VDG VGS IDM ID ID EAS VCC VFB PD TJ TA TSTG Parameter Drain Pin Voltage Vstr Pin Voltage Drain-Gate Voltage Gate-Source Voltage Drain Current Pulsed(3) Continuous Drain Current (Tc=25C) Continuous Drain Current (Tc=100C) Single Pulsed Avalanche Energy(4) Supply Voltage Feedback Voltage Range Total Power Dissipation Operating Junction Temperature Operating Ambient Temperature Storage Temperature Value Unit 650 650 650 20 1.5 0.5 0.32 10 20 -0.3 to VSTOP 1.40 Internally limited -25 to +85 -55 to +150 V V V V A A A mJ V V W C C C FSDM311 Green Mode Fairchild Power Switch (FPSTM) Absolute Maximum Ratings Notes: 3. Repetitive rating: Pulse width is limited by maximum junction temperature. 4. L = 24mH, starting TJ = 25C. Thermal Impedance FSDM311 8DIP. TA=25C, unless otherwise specified. Symbol Parameter (5) Value Unit JA Junction-to-Ambient Thermal Impedance 88.84 C/W JC Junction-to-Case Thermal Impedance(6) 13.94 C/W Notes: 5. Free standing with no heat sink, without copper clad. (Measurement Condition - Just before junction temperature TJ enters into OTP.) 6. Measured on the DRAIN pin close to plastic interface. All items are tested with the standards JESD 51-2 and 51-10 (DIP). (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 4 www.fairchildsemi.com TA=25C, unless otherwise specified. Symbol Parameter Conditions Min. Typ. Max. Unit - - 25 - - 200 1.0 - 14 1.3 162 18 3.8 9.5 19 33 42 7.0 3.1 0.4 19 - 61 60 8 6 0.35 10 4.2 67 5 67 9 7 0.40 15 4.5 73 10 74 10 8 0.45 20 4.8 KHz % % V V mA ms V - 0.3 0.6 mV/C Hysteresis 0.6 0.45 - 0.7 0.55 150 0.8 0.65 - V V mV 0.55 145 4.5 5 0.625 5.0 6 A C V V 3V VFB VSD 0.475 125 4.0 20 4 A - 1.5 3.0 mA 450 550 650 A SenseFET SECTION IDSS Zero-Gate-Voltage Drain Current RDS(ON) Drain-Source On-State Resistance(7) gfs Forward Trans-Conductance CISS Input Capacitance COSS Output Capacitance CRSS Reverse Transfer Capacitance td(on) Turn-On Delay Time tr Rise Time td(off) Turn-Off Delay Time tf Fall Time Qg Total Gate Charge Qgs Gate-Source Charge Qgd Gate-Drain (Miller) Charge CONTROL SECTION fOSC Switching Frequency fOSC Switching Frequency Variation(8) DMAX Maximum Duty Cycle VSTART UVLO Threshold Voltage VSTOP IFB Feedback Source Current tS/S Internal Soft-Start Time VREF Reference Voltage(9) Reference Voltage Variation with VREF/T Temperature(8)(9) BURST-MODE SECTION VBURH Burst-Mode Voltage VBURL VBUR(HYS) PROTECTION SECTION ILIM Peak Current Limit TSD Thermal Shutdown Temperature(9) VSD Shutdown Feedback Voltage VOVP Over-Voltage Protection IDELAY Shutdown Delay Current TOTAL DEVICE SECTION IOP Operating Supply Current (control part only) ICH Start-Up Charging Current VDS=650V, VGS=0V VDS=520V, VGS=0V, TC=125C VGS=10V, ID=0.5A VDS=50V, ID=0.5A VGS=0V, VDS=25V, f=1MHz VDS=325V, ID=1.0A VGS=10V, ID=1.0A, VDS=325V -25C TA 85C VFB=GND VFB=GND 0V VFB 3V -25C TA 85C TJ=25C VCC 16V VCC=0V , VSTR=50V A S pF ns nC FSDM311 Green Mode Fairchild Power Switch (FPSTM) Electrical Characteristics Notes: 7. Pulse test: Pulse width 300s, duty 2%. 8. These parameters, although guaranteed, are tested in EDS (wafer test) process. 9. These parameters, although guaranteed, are not 100% tested in production. (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 5 www.fairchildsemi.com 1.15 1.15 1.10 1.10 1.05 1.05 1.00 1.00 IOP Vref These characteristic graphs are normalized at TA = 25C. 0.95 0.95 0.90 0.90 0.85 -50 0 50 100 0.85 150 -50 0 1.15 1.15 1.10 1.10 1.05 1.05 1.00 0.95 0.90 0.90 0 50 100 0.85 150 -50 0 Temperature [C] 1.10 1.10 1.05 1.05 DMAX fOSC 1.15 1.00 0.95 0.90 0.90 50 100 0.85 150 -50 0 50 100 150 Temperature [C] Temperature [C] Figure 8. Operating Frequency (fOSC) vs. TA (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 150 1.00 0.95 0 100 Figure 7. Stop Threshold Voltage (VSTOP) vs. TA 1.15 -50 50 Temperature [C] Figure 6. Start Threshold Voltage (VSTART) vs. TA 0.85 150 1.00 0.95 -50 100 Figure 5. Operating Supply Current (IOP) vs. TA VSTOP VSTAART Figure 4 Reference Voltage (VREF) vs. TA 0.85 50 Temperature [C] Temperature [C] FSDM311 Green Mode Fairchild Power Switch (FPSTM) Temperature Characteristics Figure 9. Maximum Duty Cycle (DMAX) vs. TA 6 www.fairchildsemi.com 1.15 1.10 1.10 1.05 1.05 1.00 1.00 IFB ILIM 1.15 0.95 0.95 0.90 0.90 0.85 -50 0 50 100 0.85 150 -50 0 Temperature [C] 1.15 1.15 1.10 1.10 1.05 1.05 1.00 0.95 0.90 0.90 0 50 150 1.00 0.95 -50 100 Figure 11. Feedback Source Current (IFB) vs. TA VSD IDELAY Figure 10. Peak Current Limit (ILIM) vs. TA 0.85 50 Temperature [C] 100 0.85 150 FSDM311 Green Mode Fairchild Power Switch (FPSTM) Temperature Characteristics (continued) -50 0 50 100 150 Temperature [C] Temperature [C] Figure 12. Shutdown Delay Current (IDELAY) vs. TA Figure 13. Shutdown Feedback Voltage (VSD) vs. TA 1.15 1.10 VOVP 1.05 1.00 0.95 0.90 0.85 -50 0 50 100 150 Temperature [C] Figure 14. Over-Voltage Protection (VOVP) vs. TA (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 7 www.fairchildsemi.com FSDM311 Green Mode Fairchild Power Switch (FPSTM) Functional Description 1. Start-up: At start-up, the internal high-voltage current source supplies the internal bias and charges the external Vcc capacitor, as shown in Figure 15. In the case of the FSDM311, when Vcc reaches 9V, the device starts switching and the internal high-voltage current source stops charging the capacitor. The device is in normal operation provided that Vcc does not drop below 7V. After start-up, the bias is supplied from the auxiliary transformer winding. Figure 15. Internal Startup Circuit Calculating the Vcc capacitor is an important step in design with the FSDM311. At initial start-up in the FSDM311, the maximum value of start operating current ISTART is about 100A, which supplies current to UVLO and Vref Blocks. The charging current IVcc of the Vcc capacitor is equal to ISTR - ISTART. After VCC reaches the UVLO start voltage, only the bias winding supplies Vcc current to the device. When the bias winding voltage is not sufficient, the Vcc level decreases to the UVLO stop voltage and the internal current source is activated again to charge the Vcc capacitor. To prevent this Vcc fluctuation (charging/discharging), a Vcc with a value between 10uF and 47F should be chosen. Figure 16. Charging Vcc Capacitor Through Vstr 2. Feedback Control: The FSDM311 is a voltage-mode controlled device, as shown in Figure 17. Usually, an opto-coupler with shunt regulator, like KA431, is used to implement the feedback network. The feedback voltage is compared with an internally generated sawtooth waveform, which directly controls the duty cycle. When the KA431 reference pin voltage exceeds the internal reference voltage of 2.5V, the opto-coupler LED current increases, the feedback voltage Vfb is pulled down, and it reduces the duty cycle. This happens when the input voltage increases or the output load decreases. Figure 17. PWM and Feedback Circuit (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 8 www.fairchildsemi.com 4. Protection Circuit: The FSDM311 has several protective functions, such as overload protection (OLP), over-voltage protection (OVP), under-voltage lockout (UVLO), and thermal shutdown (TSD). Because these protection circuits are fully integrated in the IC without external components, the reliability is improved without increasing cost. Once a fault condition occurs, switching is terminated and the SenseFET remains off. This causes Vcc to fall. When Vcc reaches the UVLO stop voltage VSTOP (7V), the protection is reset and the internal high-voltage current source charges the Vcc capacitor via the Vstr pin. When Vcc reaches the UVLO start voltage VSTART (9V), the device resumes normal operation. In this manner, the auto-restart can alternately enable and disable the switching of the power SenseFET until the fault condition is eliminated. t1 2 = C F B V ( t 2 ) - V ( t1 ) ; ID E L A Y I D E L A Y = 5 A , V ( t1 ) = 3V , V ( t 2 ) = 4 .5V Figure 19. Overload Protection (OLP) FSDM311 Green Mode Fairchild Power Switch (FPSTM) increases until it reaches 4.5V, when the switching operation is terminated, as shown in Figure 19. The shutdown delay time is the time required to charge Cfb from 3V to 4.5V with a 5A current source. 3. Leading Edge Blanking (LEB): At the instant the internal SenseFET is turned on, the primary-side capacitance and secondary-side rectifier diode reverse recovery typically cause a high current spike through the SenseFET. Excessive voltage across the Rsense resistor leads to incorrect pulse-by-pulse current limit protection. To avoid this, a leading edge blanking (LEB) circuit disables pulse-by-pulse current limit protection block for a fixed time (tLEB) after the SenseFET turns on. 4.2 Thermal Shutdown (TSD): The SenseFET and the control IC are integrated, making it easier for the control IC to detect the temperature of the SenseFET. When the temperature exceeds approximately 145C, thermal shutdown is activated. 5. Soft-Start: The FPS has an internal soft-start circuit that slowly increases the feedback voltage, together with the SenseFET current, right after it starts up. The typical soft-start time is 15ms, as shown in Figure 20, where progressive increment of the SenseFET current is allowed during the start-up phase. The soft-start circuit progressively increases current limits to establish proper working conditions for transformers, inductors, capacitors, and switching devices. It also helps to prevent transformer saturation and reduces the stress on the secondary diode. Figure 18. Protection Block 4.1 Overload Protection (OLP): Overload is defined as the load current exceeding a pre-set level due to an unexpected event. In this situation, the protection circuit should be activated to protect the SMPS. However, even when the SMPS is operating normally, the overload protection (OLP) circuit can be activated during the load transition. To avoid this undesired operation, the OLP circuit is designed to be activated after a specified time to determine whether it is a transient situation or true overload situation. If the output consumes more than the maximum power determined by ILIM, the output voltage (Vo) decreases below its rating voltage. This reduces the current through the optocoupler LED, which also reduces the opto-coupler transistor current, thus increasing the feedback voltage (VFB). If VFB exceeds 3V, the feedback input diode is blocked and the 5A current source (IDELAY) starts to charge Cfb slowly up to Vcc. In this condition, VFB (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 Figure 20. Internal Soft-Start 9 www.fairchildsemi.com FSDM311 Green Mode Fairchild Power Switch (FPSTM) 6. Burst Operation: To minimize the power dissipation in standby mode, the FSDM311 enters burst--mode operation. As the load decreases, the feedback voltage decreases. The device automatically enters burst mode when the feedback voltage drops below VBURL(0.55V). At this point, switching stops and the output voltages start to drop. This causes the feedback voltage to rise. Once it passes VBURH (0.70V), switching starts again. The feedback voltage falls and the process repeats. Burstmode operation alternately enables and disables switching of the power MOSFET to reduce the switching loss in the standby mode. Figure 21. Burst Operation Block Figure 22. Burst Operation Function (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 10 www.fairchildsemi.com Methods of Reducing Audible Noise Switching mode power converters have electronic and magnetic components, which generate audible noises when the operating frequency is in the range of 20~20,000Hz. Even though they operate above 20KHz, they can make noise in some load conditions. Designers can employ several methods to reduce noise, including: Glue or Varnish The most common method involves using glue or varnish to tighten magnetic components. The motion of core, bobbin, and coil; and the chattering or magnetostriction of core, can cause the transformer to produce audible noise. The use of rigid glue and varnish helps reduce the transformer noise, but can crack the core because sudden changes in the ambient temperature cause the core and the glue to expand or shrink at different rates. Figure 23. Equal Loudness Curves Ceramic Capacitor Using a film capacitor instead of a ceramic capacitor as a snubber is another noise reduction solution. Some dielectric materials show a piezoelectric effect, depending on the electric field intensity. Hence, a snubber capacitor becomes one of the most significant sources of audible noise. It is possible to use a Zener clamp circuit instead of an RCD snubber for higher efficiency as well as lower audible noise. Figure24. Typical Feedback Network of FPS Other Reference Materials AN-4134: Design Guidelines for Off-line Forward Converters Using Fairchild Power Switch (FPSTM) Adjusting Sound Frequency Moving the fundamental frequency of noise out of the 2~4KHz range is the third method. Generally, humans are more sensitive to noise in the range of 2~4KHz. When the fundamental frequency of noise is located in this range, the noise is perceived as louder, although the noise intensity level is identical. Refer to Figure 23 for equal loudness curves. AN-4137: Design Guidelines for Off-line Flyback Converters Using Fairchild Power Switch (FPSTM) AN-4138: Design Considerations for Battery Charger Using Green Mode Fairchild Power Switch (FPSTM) AN-4140: Transformer Design Consideration for Off-line Flyback Converters Using Fairchild Power Switch (FPSTM) When FPS acts in burst mode and the burst operation is suspected to be a source of noise, this method may be helpful. If the frequency of burst mode operation lies in the range of 2~4KHz, adjusting the feedback loop can shift the burst operation frequency. To reduce the burst operation frequency, increase a feedback gain capacitor (CF), opto-coupler supply resistor (RD), and feedback capacitor (CB); and decrease a feedback gain resistor (RF), as shown in Figure 24. (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 FSDM311 Green Mode Fairchild Power Switch (FPSTM) Application Tips AN-4141: Troubleshooting and Design Tips for Fairchild Power Switch (FPSTM) Flyback Applications AN-4147: Design Guidelines for RCD Snubber of Flyback AN-4148: Audible Noise Reduction Techniques for Fairchild Power Switch (FPSTM) Applications 11 www.fairchildsemi.com Application Output Power Input Voltage 12.5W DC 275~375V 10W DC 120~375V PC Standby Power (Demo board) Output Voltage (Max. Current) 5.1V (2.5A, isolated) 15V (20mA, non-isolated) 5.1V (2.0A, isolated) 15V (20mA, non-isolated) Features Auxiliary Power for PC Power Supply with Passive PFC DC Input Voltage 275V ~ 375V (Voltage Doubler) for 12.5W Output DC Input Voltage 120V ~ 375V (Off-Line Universal Input) for 10W Output Isolated Secondary Output 5.1V / 2.5A (max), 3.5A (peak) @VIN=275~375VDC Isolated Secondary Output 5.1V / 2.0A (max), 2.5A (peak) @VIN =120~375VDC Non-Isolated Aux-Output 15V(13~17V) / 10mA (up to 20mA) Regulation 5.1V 2.5% - Accuracy depends on Reference (e.g. shunt regulator or precision resistors) Low No-Load Power Consumption: < 100mW @ All Input Voltage < 820mW @ All Input Voltage, 0.5W Output High Efficiency: > 80% @ 375Vdc Input, 12.5W Output > 79% @ 160Vdc Input, 10W Output FSDM311 Green Mode Fairchild Power Switch (FPSTM) Typical Application Example Schematic Note: The selection of aux-winding diode D2 affects Aux-Output (Vcc) regulation. If another component should be used, its validity must be verified experimentally. Figure 25. Schematic of FSDM311 PC Standby Power (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 12 www.fairchildsemi.com TOP BOTTOM (pin side) Figure 26. Transformer Construction Diagram 3~4mm 3~4mm FSDM311 Green Mode Fairchild Power Switch (FPSTM) Transformer Construction Return Wire Insulation Tape R < Wire (W5v or Wcc) Core Figure 27. Winding Direction for Each Winding (Left) and Cross-Sectional View for W5v / Wcc Insulation Taping (Right) Figure 28. Details on W5v / Wcc Insulation Taping (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 13 www.fairchildsemi.com All windings should be wound tightly and evenly across the bobbin. Winding Pin(S F) Wire (:mm) Turns Winding Method (10) Top Insulation: Polyester Tape t = 0.025mm, 2 Layers f2 1 Wp4 0.22 x1 53 Solenoid winding (10) Insulation: Polyester Tape t = 0.025mm, 1 Layers Wp3 2 f2 0.22 x1 53 Solenoid winding (11) Insulation: Polyester Tape t = 0.025mm, 2 Layers W5v 7,8,9 11,12 0.55 x2 12 Bifilar Solenoid winding Insulation: Polyester Tape t = 0.025mm, 2 Layers(11) Wcc 56 0.35 x1 34 Solenoid winding Insulation: Polyester Tape t = 0.025mm, 1 Layers(10) Wp2 f1 2 0.22 x1 53 Solenoid winding (10) Insulation: Polyester Tape t = 0.025mm, 1 Layers Bottom Wp1 3 f1 0.22 x1 53 Solenoid winding Notes: 10. Overlapped section length between the start and the end of insulation tape is about 3mm - see Figure 29. 11. See Figure 27 (right) and Figure 28 for details. FSDM311 Green Mode Fairchild Power Switch (FPSTM) Winding Specification Figure 29. Overlapped Section of Insulation Taping Electrical Characteristics Pin Specification Remark Magnetizing Inductance (Lm) 1-3 2.3mH (typical) (2.2mH < Lm 2.4mH) Leakage Inductance 1-3 < 35H 67KHz, 1 V All other pins open 67KHz, 1V All other pins shorted First Resonant Frequency 1-3 > 630KHz All other pins open Core & Bobbin Core: EE1927S (SAMWHA Electronics, PL7 / Ae = 23.4mm2) Bobbin: Vertical, 12 pins, 6 pins at each side, 20mm width (bobbin wall to wall) (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 14 www.fairchildsemi.com Item Qty. Reference Value 1 1 CS1 1.5nF 50V 2 1 CY1 1nF AC250V 3 1 C1 10nF 1KV 4 1 C2 1nF 1KV Description MLCC X7R, 10% Tolerance SMD 0805 Y1 Safety Capacitor Ceramic Ceramic Low ESR (40m) Electrolytic (e.g. Samwha Electric WB series) Low ESR (70m) Electrolytic (e.g. Samwha Electric WB series) 5 2 C3, C4 1000F 10V 6 1 C5 470F 10V 7 1 C6 47nF 50V 8 1 C7 150nF 50V Ceramic X7R, 5% Tolerance 9 2 C8, C9 47F 25V Electrolytic 10 2 D1, D2 1N4007 1A, 1000V Diode (Fairchild Semiconductor) Ceramic X7R, 5% Tolerance 11 1 D3 SB540 5A, 40V Schottky Diode 12 1 D4 1N4148 200mA, 100V Fast Switching Diode (Fairchild Semiconductor) 13 1 J1 (Wire) 14 1 L1 1H 3.5A Inductor 15 1 RS1 10 Resistor 1/4W SMD 1206 16 1 R1 10 Resistor 1/4W 17 1 R2 1 (R3) Jumper (Test Point) Resistor 1/4W Option for V2 Voltage Clamping 18 1 R4 6.2k 2% 2% Precision Resistor 1/4W 19 1 R5 6k 2% 2% Precision Resistor 1/4W 20 1 R6 20k Resistor 1/4W 21 1 R7 200 Resistor 1/4W 22 1 R8 680 Resistor 1/4W 23 1 T1 EE1927S Transformer (Core: EE1927S Samwha Electronics) 24 1 U1 FSDM311 Fairchild Power Switch (Fairchild Semiconductor FPS) 25 1 U2 H11A817B Opto-coupler (Fairchild Semiconductor) 26 1 U3 KA431A 27 1 ZD1 P6KE180A 28 1 ZD2 1N4763A Shunt Regulator (Fairchild Semiconductor) 180V TVS 91V 1W Zener Diode (ZD3) Option for V2 Voltage Clamping (ZD4) Option for Protecting VFB Pin (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 FSDM311 Green Mode Fairchild Power Switch (FPSTM) Circuit Part List 15 www.fairchildsemi.com FSDM311 Green Mode Fairchild Power Switch (FPSTM) Layout Information Single layer, size 59 x 40mm Figure 30. PCB Layout - Top- Side Print (Top) and Bottom-Side Print (Bottom) (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 16 www.fairchildsemi.com 8-DIP Dimensions are in millimeters (inches) unless otherwise noted. (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 17 FSDM311 Green Mode Fairchild Power Switch (FPSTM) Physical Dimensions www.fairchildsemi.com 8-LSOP Dimensions are in millimeters (inches) unless otherwise noted. (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 18 FSDM311 Green Mode Fairchild Power Switch (FPSTM) Physical Dimensions (Continued) www.fairchildsemi.com ACExTM ActiveArrayTM BottomlessTM Build it NowTM CoolFETTM CROSSVOLTTM DOMETM EcoSPARKTM 2 E CMOSTM EnSignaTM FACTTM FACT Quiet SeriesTM (R) FAST FASTrTM FPSTM FRFETTM GlobalOptoisolatorTM GTOTM HiSeCTM 2 I CTM i-LoTM ImpliedDisconnectTM IntelliMAXTM ISOPLANARTM LittleFETTM MICROCOUPLERTM MicroFETTM MicroPakTM MICROWIRETM MSXTM MSXProTM OCXTM OCXProTM (R) OPTOLOGIC OPTOPLANARTM PACMANTM POPTM Power247TM PowerEdgeTM PowerSaverTM (R) PowerTrench (R) QFET QSTM QT OptoelectronicsTM Quiet SeriesTM RapidConfigureTM RapidConnectTM ScalarPumpTM SerDesTM (R) SILENT SWITCHER SMART STARTTM SPMTM StealthTM SuperFETTM SuperSOTTM-3 SuperSOTTM-6 SuperSOTTM-8 SyncFETTM TCMTM TinyBoostTM TinyBuckTM (R) TinyLogic TINYOPTOTM TinyPowerTM TinyPWMTM TruTranslationTM UHCTM (R) UltraFET UniFETTM VCXTM WireTM Across the board. Around the world.TM Programmable Active DroopTM (R) The Power Franchise DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILD'S WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. FSDM311 Green Mode Fairchild Power Switch (FPSTM) TRADEMARKS The following are registered and unregistered trademarks Fairchild Semiconductor owns or is authorized to use and is not intended to be an exhaustive list of all such trademarks. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Product Status Advance Information Formative or In Design This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Definition Preliminary First Production This datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. No Identification Needed Full Production This datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Obsolete Not In Production This datasheet contains specifications on a product that has been discontinued by Fairchild Semiconductor. The datasheet is printed for reference information only. Rev. I20 (c) 2003 Fairchild Semiconductor Corporation FSDM311 Rev. 1.1.0 * 7/14/06 19 www.fairchildsemi.com