108-1542 Product Specification 10Nov04 Rev B EC 0990-1499-04 Mini-Universal MATE-N-LOK* Connector 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for MATE-N-LOK* mini-universal connectors. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 1.3. Qualification Test Results Successful qualification testing on the subject product line was completed on 02Aug04. The Qualification Test Report number for this testing is 501-589. This documentation is on file at and available from Engineering Practices and Standards (EPS). 2. APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1. Tyco Electronics Documents ! ! ! ! ! | | 2.2. 102-950: 109 Series: 109-197: 114-16017: 501-589: Qualification of Separable Interface Connectors Test Specifications as indicated in Figure 1 AMP Test Specifications vs EIA and IEC Test Methods Application Specification Qualification Test Report Commercial Standard EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications 3. REQUIREMENTS 3.1. Design and Construction Product shall be of the design, construction and physical dimensions specified on the applicable product drawing. 3.2. Materials Materials used in the construction of this product shall be as specified on the applicable product drawing. (c)2004 Tyco Electronics Corporation Harrisburg, PA All International Rights Reserved. * Trademark | Indicates change For latest revision call AMP FAX*/Product Info number 1-800-522-6752. 1 of 8 For Regional Customer Service, visit our website at www.tycoelectronics.com LOC B 108-1542 3.3. Ratings ! ! ! 3.4. Voltage: 600 volts AC or DC Current: 11.2 amperes maximum Temperature: -55 to 105/C Performance and Test Description Product is designed to meet the electrical, mechanical and environmental performance requirements specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental conditions per EIA-364. 3.5. Test Requirements and Procedures Summary Test Description Requirement Procedure Initial examination of product. Meets requirements of product drawing. EIA-364. Visual and dimensional (C of C) inspection per product drawing. Final examination of product. Meets visual requirements. EIA-364. Visual inspection. ELECTRICAL Dry circuit resistance. 10 milliohms maximum initial. 20 milliohms maximum final. EIA-364-23. Subject specimens to 100 milliamperes maximum and 20 millivolts maximum open circuit voltage. See Figure 3. Insulation resistance. 1000 megohms minimum initial. 100 megohms minimum final. EIA-364-21. Test between adjacent contacts of mated specimens. Withstanding voltage. 1 minute hold with no breakdown or EIA-364-20, Condition I. flashover. 1500 volts AC at sea level. Test between adjacent contacts of mated specimens. Temperature rise vs current. 30/C maximum temperature rise at specified current. EIA-364-70, Method 1. Stabilize at a single current level until 3 readings at 5 minute intervals are within 1/C. See Figure 4. Figure 1 (cont) Rev B 2 of 8 108-1542 Test Description Requirement Procedure MECHANICAL Termination tensile strength. Wire Size AWG 30 28 26 24 22 20 18 16 Newtons [lbf] (Minimum) 8.9 [2] 13.3 [3] 17.8 [4] 31.1 [7] 48.9 [11] 62.3 [14] 80.1 [18] 102.3 [23] EIA-364-8. Determine crimp tensile at a maximum rate of 25 6 mm [.98 .24 in] per minute. Vibration, sinusoidal. No discontinuities of 10 microseconds or longer duration. See Note. EIA-364-28, Test Condition I. Subject mated specimens to 10-5510 Hz traversed in 1 minute with 1.5 mm [.06 in] maximum total excursion. 2 hours in each of 3 mutually perpendicular planes. See Figure 5. Mechanical shock. No discontinuities of 10 microseconds or longer duration. See Note. EIA-364-27, Method A. Subject mated specimens to 50 G's half-sine shock pulses of 11 milliseconds duration. 3 shocks in each direction applied along 3 mutually perpendicular planes, 18 total shocks. See Figure 6. Durability. See Note. EIA-364-9. Mate and unmate tin plated specimens for 20 cycles, and gold plated specimens for 50 cycles at a maximum rate of 500 cycles per hour. Contact retention. Contacts shall not dislodge. See Note. EIA-364-29. Apply an axial load of 35.6 N [8 lbf] at a maximum rate of 12.7 mm [.5 in] per minute. Contact insertion force. 13.3 N [3 lbf] maximum per contact. AMP Spec 109-41. Measure force necessary to insert a contact into the housing at a maximum rate of 12.7 mm [.5 in] per minute. Mating force. 6.7 N [1.5 lbf] maximum per circuit initial. EIA-364-13. Measure force necessary to mate specimens without locking latches at a maximum rate of 12.7 mm [.5 in] per minute. Figure 1 (cont) Rev B 3 of 8 108-1542 Test Description Requirement Procedure Unmating force. 0.7 N [.15 lbf] minimum per circuit final. EIA-364-13. Measure force necessary to unmate specimens at a maximum rate of 12.7 mm [.5 in] per minute. Housing lock strength. 40 N [9 lbf] minimum. EIA-364-98. Determine housing lock strength at maximum rate of 12.7 mm [.5 in] per minute. Housing panel retention. 133.4 N [30 lbf]. Determine housing panel retention at maximum rate of 12.7 mm [.5 in] per minute. ENVIRONMENTAL Thermal shock. See Note. EIA-364-32, Test Condition VII. Subject specimens to 25 cycles between -55 and 105/C. Humidity-temperature cycling. See Note. EIA-364-31, Method III. Subject specimens to 10 cycles (10 days) between 25 and 65/C at 80 to 100% RH. Temperature life. See Note. EIA-364-17, Method A, Test Condition 4. Subject mated specimens to 105/C for 580 hours. Mixed flowing gas. See Note. EIA-364-65, Class IIA (4 gas). Subject mated specimens to environmental Class IIA for 20 days. NOTE Shall meet visual requirements, show no physical damage, and meet requirements of additional tests as specified in the Product Qualification and Requalification Test Sequence shown in Figure 2. Figure 1 (end) Rev B 4 of 8 108-1542 3.6. Product Qualification and Requalification Test Sequence Test Group (a) Test or Examination 1 2 3 4 5 Test Sequence (b) Initial examination of product Dry circuit resistance 1 1 3,7 2,7 1 Insulation resistance 3,7 Withstanding voltage 4.8 Temperature rise vs current 1 3,8 Termination tensile strength 2 Vibration, sinusoidal 5 Mechanical shock 6 Durability 4 6(c) Contact retention 10 Contact insertion force 2 Mating force 2 Unmating force 8 Housing lock strength 9 Housing panel retention 2 Thermal shock 5 Humidity-temperature cycling 4(d) Temperature life NOTE (a) (b) (c) (d) 6 5 Mixed flowing gas Final examination of product 1 4(d) 9 9 11 3 3 See paragraph 4.1.A. Numbers indicate sequence in which tests are performed. Discontinuities shall not be measured. Energize at 18C level for 100% loadings per Quality Specification 102-950. The 4th test in this sequence shall be either humidity-temperature cycling for tin plated specimens or mixed flowing gas for gold plated specimens. Precondition specimens with 5 durability cycles. Figure 2 Rev B 5 of 8 108-1542 4. QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specimen Selection Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. All test groups shall each consist of 5 random connector assemblies. All contacts shall be crimped to appropriate test conductors per Specification 114-16017. | B. Test Sequence Qualification inspection shall be verified by testing specimens as specified in Figure 2. 4.2. Requalification Testing If changes significantly affecting form, fit or function are made to the product or manufacturing process, product assurance shall coordinate requalification testing, consisting of all or part of the original testing sequence as determined by development/product, quality and reliability engineering. 4.3. Acceptance Acceptance is based on verification that the product meets the requirements of Figure 1. Failures attributed to equipment, test setup or operator deficiencies shall not disqualify the product. If product failure occurs, corrective action shall be taken and specimens resubmitted for qualification. Testing to confirm corrective action is required before resubmittal. 4.4. Quality Conformance Inspection The applicable quality inspection plan shall specify the sampling acceptable quality level to be used. Dimensional and functional requirements shall be in accordance with the applicable product drawing and this specification. NOTE Bulk wire resistance shall be subtracted from resistance readings. Figure 3 Dry Circuit Resistance Measurement Points Rev B 6 of 8 108-1542 20.0 18.0 Current (Amperes DC) 16.0 14.0 12.0 10.0 8.0 6.0 4.0 2.0 0.0 0 25 50 75 100 Ambient Temperature (C) Figure 4A Current Carrying Capability (11.21 amperes) Wire Size (AWG) Percent Connector Loading Single 47% 100% Brass/Tin Pin and Socket NOTE 16 1.00 .668 .486 30 .248 .166 .121 To determine acceptable current carrying capacity for percentage connector loading and wire gage indicated, use the Multiplication Factor (F) from the above chart and multiply it times the Base rated Current for a single circuit at the maximum ambient operating temperature shown in Figures 4A. Figure 4B Current Rating Rev B 7 of 8 108-1542 Figure 5 Vibration Mounting Fixture Figure 6 Mechanical Shock Mounting Fixture Rev B 8 of 8