SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
DLow Noise
10 Hz . . . 15 nV/√Hz
1 kHz . . . 10.5 nV/√Hz
D10000-pF Load Capability
D20-mA Min Short-Circuit Output Current
D27-V/µs Min Slew Rate
DHigh Gain-Bandwidth Product . . . 5.9 MHz
DLow VIO . . . 500 µV Max at 25°C
DSingle or Split Supply ...4 V to 44 V
DFast Settling Time
340 ns to 0.1%
400 ns to 0.01%
DSaturation Recovery . . . 150 ns
DLarge Output Swing
VCC− +0.1 V to VCC+ − 1 V
description
The TLE214x and TLE214xA devices are high-performance, internally compensated operational amplifiers
built using Texas Instruments complementary bipolar Excalibur process. The TLE214xA is a tighter offset
voltage grade of the TLE214x. Both are pin-compatible upgrades to standard industry products.
The design incorporates an input stage that simultaneously achieves low audio-band noise of 10.5 nV/√Hz with
a 10-Hz 1/f corner and symmetrical 40-V/µs slew rate typically with loads up to 800 pF. The resulting low
distortion and high power bandwidth are important in high-fidelity audio applications. A fast settling time of
340 ns to 0.1% of a 10-V step with a 2-kΩ/100-pF load is useful in fast actuator/positioning drivers. Under similar
test conditions, settling time to 0.01% is 400 ns.
The devices are stable with capacitive loads up to 10 nF, although the 6-MHz bandwidth decreases to 1.8 MHz
at this high loading level. As such, the TLE214x and TLE214xA are useful for low-droop sample-and-holds and
direct buffering of long cables, including 4-mA to 20-mA current loops.
The special design also exhibits an improved insensitivity to inherent integrated circuit component mismatches
as is evidenced by a 500-µV maximum offset voltage and 1.7-µV/°C typical drift. Minimum common-mode
rejection ratio and supply-voltage rejection ratio are 85 dB and 90 dB, respectively.
Device performance is relatively independent of supply voltage over the ±2-V to ±22-V range. Inputs can
operate between VCC− − 0.3 to VCC+ − 1.8 V without inducing phase reversal, although excessive input current
may flow out of each input exceeding the lower common-mode input range. The all-npn output stage provides
a nearly rail-to-rail output swing of VCC− − 0.1 to VCC+ − 1 V under light current-loading conditions. The device
can sustain shorts to either supply since output current is internally limited, but care must be taken to ensure
that maximum package power dissipation is not exceeded.
Both versions can also be used as comparators. Dif ferential inputs of VCC± can be maintained without damage
to the device. Open-loop propagation delay with TTL supply levels is typically 200 ns. This gives a good
indication as to output stage saturation recovery when the device is driven beyond the limits of recommended
output swing.
Both the TLE214x and TLE214xA are available in a wide variety of packages, including both the
industry-standard 8-pin small-outline version and chip form for high-density system applications. The C-suffix
devices are characterized for operation from 0°C to 70°C, I-suffix devices from −40°C to 105°C, and M-suffix
devices over the full military temperature range of −55°C to 125°C.
Copyright 1997 − 2006, Texas Instruments Incorporated
!"#$ % &'!!($ #% )'*+&#$ ,#$(-
!,'&$% &!" $ %)(&&#$% )(! $.( $(!"% (#% %$!'"($%
%$#,#!, /#!!#$0- !,'&$ )!&(%%1 ,(% $ (&(%%#!+0 &+',(
$(%$1 #++ )#!#"($(!%-
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
2POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141 AVAILABLE OPTIONS
PACKAGED DEVICES
TAVIOmax
AT 25°CSMALL OUT-
LINE†
(D)
CERAMIC DIP
(JG) PLASTIC DIP
(P)
0°C to 70°C500 µV
900 µVTLE2141ACD
TLE2141CD —TLE2141ACP
TLE2141CP
−40°C to 105°C500 µV
900 µVTLE2141AID
TLE2141ID —TLE2141AIP
TLE2141IP
−55°C to 125°C500 µV
900 µV—
TLE2141MD TLE2141AMJG
TLE2141MJG —
—
†The D packages are available taped and reeled. Add R suffix to device type (e.g.,
TLE2141ACDR).
TLE2142 AVAILABLE OPTIONS
PACKAGED DEVICES
TAVIOmax
AT 25°C
SMALL
OUTLINE†
(D)
CHIP
CARRIER
(FK)
CERAMIC
DIP
(JG)
PLASTIC
DIP
(P)
TSSOP‡
(PW)
CERAMIC
FLAT PACK
(U)
0°C to 70°C
750 µV TLE2142ACD — — TLE2142ACP — —
0°C to 70°C1200 µV TLE2142CD — — TLE2142CP TLE2142CPWLE —
−40°C to 105°C
750 µV TLE2142AID — — TLC2142AIP — —
−40°C to 105°C1200 µV TLE2142ID — — TLC2142IP — —
−55°C to 125°C
750 µV TLE2142AMD TLE2142AMFK TLE2142AMJG — — TLE2142AMU
−55°C to 125°C1200 µV TLE2142MD TLE2142MFK TLE2142MJG — — TLE2142MU
†The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2142ACDR).
‡The PW packages are available left-ended taped and reeled. Add LE the suffix to device type (e.g., TLC2142CPWLE).
TLE2144 AVAILABLE OPTIONS
VIOmax
PACKAGED DEVICES
TA
V
IO
max
AT 25°CSMALL OUTLINE†
(DW) CHIP CARRIER
(FK) CERAMIC DIP
(J) PLASTIC DIP
(N)
0°C to 70°C1.5 mV
2.4 mV —
TLE2144CDW —
——
—TLE2144ACN
TLE2144CN
−40°C to 105°C1.5 mV
2.4 mV —
TLE2144IDW —
——
—TLE2144AIN
TLE2144IN
−55°C to 125°C1.5 mV
2.5 mV —
TLE2144MDW TLE2144AMFK
TLE2144MFK TLE2144AMJ
TLE2144MJ —
—
†The DW packages are available taped and reeled. Add R suffix to device type (e.g., TLE2144CDWR).
symbol
+
−OUT
IN+
IN−
OFFSET N1
(see Note A)
OFFSET N2
(see Note A)
NOTES: A. OFFSET N1 AND OFFSET N 2
are only availiable on the
TLE2241x devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
1
2
3
4
8
7
6
5
OFFSET N1
IN−
IN+
VCC−
NC
VCC+
OUT
OFFSET N2
NC − No internal connection
3212019
910111213
4
5
6
7
8
18
17
16
15
14
NC
VCC+
NC
OUT
NC
NC
IN−
NC
IN+
NC
NC
OFFSET N1
NC
OFFSET N2
NC NC
NC
NC
NC
V
CC −
1
2
3
4
8
7
6
5
1OUT
1IN−
1IN+
VCC −
VCC+
2OUT
2IN−
2IN+
3 2 1 20 19
910111213
4
5
6
7
8
18
17
16
15
14
NC
2OUT
NC
2IN−
NC
NC
1IN−
NC
1IN+
NC
NC
1OUT
NC
NC NC
NC
NC
2IN +
CC −
V
VCC +
TLE2142
D, JG, OR P PACKAGE
(TOP VIEW)
TLE2142
FK PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN−
1IN+
VCC+
2IN+
2IN−
2OUT
NC
4OUT
4IN−
4IN+
VCC−
3IN+
3IN−
3OUT
NC
1
2
3
4
5
6
7
14
13
12
11
10
9
8
1OUT
1IN−
1IN+
VCC+
2IN+
2IN−
2OUT
4OUT
4IN−
4IN+
VCC−
3IN+
3IN−
3OUT
3212019
910111213
4
5
6
7
8
18
17
16
15
14
4IN+
NC
VCC−
NC
3IN+
1IN+
NC
VCC+
NC
2IN+
1IN −
1OUT
NC
3IN − 4IN −
2IN −
2
OUT
NC
3
OUT 4OUT
TLE2144
DW PACKAGE
(TOP VIEW)
TLE2144
J OR N PACKAGE
(TOP VIEW)
TLE2144
FK PACKAGE
(TOP VIEW)
TLE2141
D, JG, OR P PACKAGE
(TOP VIEW)
TLE2141
FK PACKAGE
(TOP VIEW)
TLE2142
PW PACKAGE
(TOP VIEW)
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
NC
1OUT
1OUT
1IN−
1IN+
VCC−
VCC−
NC
NC
VCC+
VCC+
2OUT
2IN−
2IN+
2IN+
NC
1
2
3
4
5
10
9
8
7
6
NC
1OUT
1IN−
1IN+
VCC−
NC
VCC+
2OUT
2IN−
2IN+
TLE2142
U PACKAGE
(TOP VIEW)
223
22
22
SLOS183C − FEBURARY 1997 − REVISED JUNE 2006
4POST OFFICE BOX 655303 DALLAS, TEXAS 75265
•
equivalent schematic
Q12
Q10
R1
Q3
R2
IN −
IN+ Q1 Q4
Q2
Q7
R5
C1
Q17 R11
R10 C2
Q16
R9
R4 R7
D1
Q5 Q8 Q13
D2
Q6
R3 R6
Q11
Q14 Q15
R8
VCC+
VCC−
R12
Q18
Q19
Q20
Q21
D5
Q24
C4
C3
R13
D3 D4
Q22
R14 R18 R19 R21
Q26
Q30
Q34 R24
Q37
R23
Q36
OUT
R20
R22
Q35
Q32
Q33
Q29
D7
D6
Q25 Q28 Q31
D8
Q27
Q23
R16
R15 R17
Q9
OFFSET N1
(see Note A)
OFFSET N2
(see Note A)
NOTE A: OFFSET N1 AND OFFSET N2 are only availiable on the TLE2241x devices.
ACTUAL DEVICE COMPONENT COUNT
COMPONENT TLE2241 TLE2242 TLE2244
Transistors 46 65 130
Resistors 24 43 86
Diodes 8 14 28
Capacitors 4 8 16
Epi-FET 1 1 2
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VCC+ (see Note 1) 22 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supply voltage, VCC− −22 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential input voltage, VID (see Note 2) ±44 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input voltage range, VI (any input) VCC+ to VCC− − 0.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input current, II (each input) ±1 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output current, IO ±80 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current into VCC+ 80 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Total current out of VCC− 80 mA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Duration of short-circuit current at (or below) 25°C (see Note 3) unlimited. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Package thermal impedance, θJA (see Notes 4 and 5): D package 97.1°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .
DW package 57.3°C/W. . . . . . . . . . . . . . . . . . . . . . . .
N package 79.7°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .
P package 84.6°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .
PW package 108.4°C/W. . . . . . . . . . . . . . . . . . . . . . .
Package thermal impedance, θJC (see Notes 4 and 5): FK package 5.6°C/W. . . . . . . . . . . . . . . . . . . . . . . . . . .
J package 15.1°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .
JG package 14.5°C/W. . . . . . . . . . . . . . . . . . . . . . . . .
U package 14.7°C/W. . . . . . . . . . . . . . . . . . . . . . . . . .
Operating free-air temperature range, TA: C suffix 0°C to 70°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I suffix −40°C to 105°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
M suffix −55°C to 125°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage temperature range −65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Case temperature for 60 seconds: FK package 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, DW, N, P, or PW package 260°C. . . . .
Lead temperature 1,6 mm (1/16 inch) from case for 60 seconds: J or JG package 300°C. . . . . . . . . . . . . . . .
†Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VCC+ and VCC−.
2. Differential voltages are at IN+ with respect to IN−. Excessive current flows, if input, are brought below VCC− − 0.3 V.
3. The output may be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
4. Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable
ambient temperature is PD = (TJ(max) − TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
5. The package thermal impedance is calculated in accordance with JESD 51-7 (plastic) or MIL-STD-883 Method 1012 (ceramic).
recommended operating conditions
C SUFFIX I SUFFIX M SUFFIX
UNIT
MIN MAX MIN MAX MIN MAX
UNIT
Supply voltage, VCC±±2±22 ±2±22 ±2±22 V
Common-mode input voltage, VIC
VCC = 5 V 0 2.9 0 2.7 0 2.7
V
Common-mode input voltage, VIC VCC± = ±15 V −15 12.9 −15 12.7 −15 12.7 V
Operating free-air temperature, TA0 70 −40 105 −55 125 °C
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
6POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141C electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2141C TLE2141AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 225 1400 200 1000
V
VIO Input
offset voltage Full range 1700 1300 µV
VIO
Temperature coefficient of
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient of
input offset voltage
VO = 2.5 V
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VO = 2.5 V
VIC = 2.5 V
RS = 50 Ω,
25°C 8 100 8 100
nA
IIO Input offset current
VIC = 2.5 V
Full range 150 150 nA
IIB
Input bias current
25°C −0.8 −2 −0.8 −2
A
IIB Input bias current Full range −2.1 −2.1 µA
0
−0.3
0
−0.3
25
°
C
0
to
−0.3
to
0
to
−0.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
3
to
3.2
to
3
to
3.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
0
0
V
voltage range
Full range
0
to
0
to
Full range
to
2.9
to
2.9
IOH = −150 A
25°C 3.9 4.1 3.9 4.1
IOH = −150 µAFull range 3.8 3.8
VOH
High-level output voltage
IOH = −1.5 mA
25°C 3.8 4 3.8 4
V
VOH High-level output voltage IOH = −1.5 mA Full range 3.7 3.7 V
IOH = −15 mA
25°C 3.2 3.7 3.2 3.7
IOH = −15 mA Full range 3.2 3.2
IOL = 150 A
25°C 75 125 75 125
IOL = 150 µAFull range 150 150
mV
VOL
Low-level output voltage
IOL = 1.5 mA
25°C 150 225 150 225 mV
VOL Low-level output voltage IOL = 1.5 mA Full range 250 250
IOL = 15 mA
25°C 1.2 1.6 1.2 1.6
V
IOL = 15 mA Full range 1.7 1.7 V
AVD
Large-signal differential
VCC =
±
2.5 V, RL = 2 k
Ω
,
25°C 50 220 50 220
V/mV
AVD
Large-signal differential
voltage amplification
VCC = ±2.5 V, RL = 2 kΩ,
VO = 1 V to −1.5 V Full range 25 25 V/mV
riInput resistance 25°C 70 70 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode rejection
VIC = VICRmin, RS = 50 Ω
25°C 85 118 85 118
dB
CMRR
Common-mode rejection
ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejection
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejection
ratio (∆VCC± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
ICC
Supply current
VO = 2.5 V,
No load,
25°C 3.4 4.4 3.4 4.4
mA
I
CC
Supply current
VO = 2.5 V,
VIC = 2.5 V
No load,
Full range 4.6 4.6
mA
†Full range is 0°C to 70°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141C operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2141C TLE2141AC
UNIT
PARAMETER
TEST CONDITIONS MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω
,
†, 45 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF†,
RL = 2 kΩ,†,
42 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.16 0.16
s
tsSettling time
AVD = −1,
2.5-V step To 0.01% 0.22 0.22 µs
Vn
Equivalent input noise voltage
RS = 20 Ω, f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.92 1.92
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.5 0.5
pA/√Hz
THD + N
Total harmonic distortion
VO = 1 V to 3 V,
RL = 2 k
Ω†
,
0.0052%
0.0052%
THD + N
Total harmonic distortion
plus noise
VO = 1 V to 3 V,
A
VD
= 2,
RL = 2 kن,
f = 10 kHz 0.0052% 0.0052%
B1
Unity-gain bandwidth
RL = 2 kن,
CL = 100 pF†
5.9
5.9
MHz
B
1
Unity-gain bandwidth
RL = 2 k
Ω
†,
C
L
= 100 pF
†
5.9 5.9 MHz
Gain-bandwidth product
RL = 2 k
Ω†
,
CL = 100 pF
†
,
5.8
5.8
MHz
Gain-bandwidth product
RL = 2 kن,
f = 100 kHz
CL = 100 pF†,
5.8 5.8 MHz
BOM
Maximum output-swing
VO(PP) = 2 V,
RL = 2 k
Ω†
,†
660
660
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 2 V,
A
VD
= 1,
RL = 2 kن,
CL = 100 pF†660 660 kHz
φmPhase margin at unity gain RL = 2 kΩ†, CL = 100 pF†57°57°
†RL and CL terminated to 2.5 V.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
8POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141C electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2141C TLE2141AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 200 900 175 500
V
VIO Input
offset voltage Full range 1300 800 µV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VIC = 0,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VIC = 0,
VO = 0
RS = 50 Ω,
25°C 7 100 7 100
nA
IIO Input offset current
VO = 0
Full range 150 150 nA
IIB
Input bias current
25°C −0.7 −1.5 −0.7 −1.5
A
IIB Input bias current Full range −1.6 −1.6 µA
−15
−15.3
−15
−15.3
25
°
C
−15
to
−15.3
to
−15
to
−15.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
13
to
13.2
to
13
to
13.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
−15
−15.3
−15
−15.3
V
voltage range
Full range
−15
to
−15.3
to
−15
to
−15.3
to
Full range
to
12.9
to
13.1
to
12.9
to
13.1
IO = −150 A
25°C 13.8 14.1 13.8 14.1
IO = −150 µAFull range 13.7 13.7
VOM+
Maximum positive peak
IO = −1.5 mA
25°C 13.7 14 13.7 14
V
VOM+
Maximum positive peak
output voltage swing IO = −1.5 mA Full range 13.6 13.6 V
output voltage swing
IO = −15 mA
25°C 13.1 13.7 13.1 13.7
IO = −15 mA Full range 13 13
IO = 150 A
25°C −14.7 −14.9 −14.7 −14.9
Maximum negative
IO = 150 µAFull range −14.6 −14.6
VOM−
Maximum negative
peak output voltage
IO = 1.5 mA
25°C −14.5 −14.8 −14.5 −14.8
V
VOM−
peak output voltage
swing
IO = 1.5 mA Full range −14.4 −14.4 V
swing
IO = 15 mA
25°C −13.4 −13.8 −13.4 −13.8
IO = 15 mA Full range −13.3 −13.3
AVD
Large-signal differential
VO = ±10 V
25°C 100 450 100 450
V/mV
AVD
Large-signal differential
voltage amplification VO = ±10 V Full range 75 75 V/mV
riInput resistance RL = 2 kΩ25°C 65 65 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin,
RS = 50 Ω
25°C 85 108 85 108
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage
rejection ratio
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
rejection ratio
(∆VCC± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
IOS
Short-circuit output
VO = 0
VID = 1 V
25°C
−25 −50 −25 −50
mA
IOS
Short-circuit output
current VO = 0 VID = −1 V 25°C20 31 20 31 mA
ICC
Supply current
VO = 0,
No load
25°C 3.5 4.5 3.5 4.5
mA
I
CC
Supply current
V
O
= 0,
No load
Full range 4.7 4.7
mA
†Full range is 0°C to 70°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141C operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2141C TLE2141AC
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω
,
27 45 27 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kΩ,
27 42 27 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.34 0.34
s
tsSettling time
AVD = −1,
10-V step To 0.01% 0.4 0.4 µs
Vn
Equivalent input noise voltage
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.89 1.89
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.47 0.47
pA/√Hz
THD + N
Total harmonic distortion plus
VO(PP) = 20 V,
RL = 2 k
Ω
,
0.01%
0.01%
THD + N
Total harmonic distortion plus
noise
VO(PP) = 20 V,
AVD = 10,
RL = 2 kΩ,
f = 10 kHz 0.01% 0.01%
B1Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz
Gain-bandwidth product
RL = 2 k
Ω
,
CL = 100 pF,
5.9
5.9
MHz
Gain-bandwidth product
RL = 2 kΩ,
f = 100 kHz
CL = 100 pF,
5.9 5.9 MHz
BOM
Maximum output-swing
VO(PP) = 20 V,
RL = 2 k
Ω
,
668
668
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 20 V,
AVD = 1,
RL = 2 kΩ,
CL = 100 pF 668 668 kHz
φmPhase margin at unity gain RL = 2 kΩ, CL = 100 pF 58°58°
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
10 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142C electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2142C TLE2142AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 220 1900 200 1500
V
VIO Input offset voltage Full range 2200 1800 µV
VIO
Temperature coefficient of
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient of
input offset voltage
VO = 2.5 V,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VO = 2.5 V,
VIC = 2.5 V
RS = 50 Ω,
25°C 8 100 8 100
nA
IIO Input offset current
VIC = 2.5 V
Full range 150 150 nA
IIB
Input bias current
25°C −0.8 −2 −0.8 −2
A
IIB Input bias current Full range −2.1 −2.1 µA
0
−0.3
0
−0.3
25
°
C
0
to
−0.3
to
0
to
−0.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
3
to
3.2
to
3
to
3.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
0
0
V
voltage range
Full range
0
to
0
to
Full range
to
2.9
to
2.9
IOH = −150 A
25°C 3.9 4.1 3.9 4.1
IOH = −150 µAFull range 3.8 3.8
VOH
High-level output voltage
IOH = −1.5 mA
25°C 3.8 4 3.8 4
V
VOH High-level output voltage IOH = −1.5 mA Full range 3.7 3.7 V
IOH = −15 mA
25°C 3.4 3.7 3.4 3.7
IOH = −15 mA Full range 3.4 3.4
IOL = 150 A
25°C 75 125 75 125
IOL = 150 µAFull range 150 150
mV
VOL
Low-level output voltage
IOL = 1.5 mA
25°C 150 225 150 225 mV
VOL Low-level output voltage IOL = 1.5 mA Full range 250 250
IOL = 15 mA
25°C 1.2 1.4 1.2 1.4
V
IOL = 15 mA Full range 1.5 1.5 V
AVD
Large-signal differential
VCC =
±
2.5 V, RL = 2 k
Ω
,
25°C 50 220 50 220
V/mV
AVD
Large-signal differential
voltage amplification
VCC = ±2.5 V, RL = 2 kΩ,
VO = 1 V to −1.5 V Full range 25 25 V/mV
riInput resistance 25°C 70 70 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin, RS = 50 Ω
25°C 85 118 85 118
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejection
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejection
ratio (∆VCC± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
ICC
Supply current
VO = 2.5 V,
No load,
25°C 6.6 8.8 6.6 8.8
mA
ICC Supply current
VO = 2.5 V,
VIC = 2.5 V
No load,
Full range 9.2 9.2 mA
†Full range is 0°C to 70°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142C operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2142C TLE2142AC
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω†
,
45 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kن,
42 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.16 0.16
s
tsSettling time
AVD = −1,
2.5-V step To 0.01% 0.22 0.22 µs
Vn
Equivalent input noise voltage
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent
input noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.92 1.92
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.5 0.5
pA/√Hz
THD + N
Total harmonic distortion plus
VO = 1 V to 3 V,
RL = 2 k
Ω†
,
0.0052%
0.0052%
THD + N
Total harmonic distortion plus
noise
VO = 1 V to 3 V,
AVD = 2,
RL = 2 kن,
f = 10 kHz 0.0052% 0.0052%
B1 Unity-gain bandwidth RL = 2 kن,CL = 100 pF 5.9 5.9 MHz
Gain-bandwidth product
RL = 2 k
Ω†
,
CL = 100 pF,
5.8
5.8
MHz
Gain-bandwidth product
RL = 2 kن,
f = 100 kHz
CL = 100 pF,
5.8 5.8 MHz
BOM
Maximum output-swing
VO(PP) = 2 V,
RL = 2 k
Ω†
,
660
660
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 2 V,
A
VD
= 1,
RL = 2 kن,
C
L
= 100 pF 660 660 kHz
φmPhase margin at unity gain RL = 2 kΩ†, CL = 100 pF 57°57°
†RL terminates at 2.5 V.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
12 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142C electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2142C TLE2142AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 290 1200 275 750
V
VIO Input offset voltage Full range 1600 1200 µV
VIO
Temperature coefficient of
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient of
input offset voltage
VIC = 0,
RS = 50 Ω,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VIC = 0,
VO = 0
RS = 50 Ω,
25°C 7 100 7 100
nA
IIO Input offset current
VO = 0
Full range 150 150 nA
IIB
Input bias current
25°C −0.7 −1.5 −0.7 −1.5
A
IIB Input bias current Full range −1.6 −1.6 µA
−15
−15.3
−15
−15.3
25
°
C
−15
to
−15.3
to
−15
to
−15.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
13
to
13.2
to
13
to
13.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
−15
−15.3
−15
−15.3
V
voltage range
Full range
−15
to
−15.3
to
−15
to
−15.3
to
Full range
to
12.9
to
13.1
to
12.9
to
13.1
IO = −150 A
25°C 13.8 14.1 13.8 14.1
IO = −150 µAFull range 13.7 13.7
VOM+
Maximum positive peak
IO = −1.5 mA
25°C 13.7 14 13.7 14
V
VOM+
Maximum positive peak
output voltage swing IO = −1.5 mA Full range 13.6 13.6 V
output voltage swing
IO = −15 mA
25°C 13.3 13.7 13.3 13.7
IO = −15 mA Full range 13.2 13.2
IO = 150 A
25°C −14.7 −14.9 −14.7 −14.9
IO = 150 µAFull range −14.6 −14.6
VOM−
Maximum negative peak
IO = 1.5 mA
25°C −14.5 −14.8 −14.5 −14.8
V
VOM−
Maximum negative peak
output voltage swing IO = 1.5 mA Full range −14.4 −14.4 V
output voltage swing
IO = 15 mA
25°C −13.4 −13.8 −13.4 −13.8
IO = 15 mA Full range −13.3 −13.3
AVD
Large-signal differential
VO = ±10 V
25°C 100 450 100 450
V/mV
AVD
Large-signal differential
voltage amplification VO = ±10 V Full range 75 75 V/mV
riInput resistance RL = 2 kΩ25°C 65 65 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin,
25°C 85 108 85 108
dB
CMRR
Common-mode
rejection ratio
VIC = VICRmin,
RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejection
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejection
ratio (∆VCC± /∆VIO)
VCC± = ± 2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
IOS
Short-circuit output current
VO = 0
VID = 1 V
25°C
−25 −50 −25 −50
mA
IOS Short-circuit output curren
t
VO = 0 VID = −1 V 25°C20 31 20 31
mA
ICC
Supply current
VO = 0,
No load
25°C 6.9 9 6.9 9
mA
ICC Supply current VO = 0, No load Full range 9.4 9.4 mA
†Full range is 0°C to 70°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142C operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2142C TLE2142AC
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω
,
27 45 27 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kΩ,
27 42 27 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.34 0.34
s
tsSettling time
AVD = −1,
10-V step To 0.01% 0.4 0.4 µs
Vn
Equivalent input noise voltage
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.89 1.89
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.47 0.47
pA/√Hz
THD + N
Total harmonic distortion plus
VO(PP) = 20 V,
RL = 2 k
Ω,
0.01%
0.01%
THD + N
Total harmonic distortion plus
noise
VO(PP) = 20 V,
AVD = 10,
RL = 2 kΩ
,
f = 10 kHz 0.01% 0.01%
B1Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz
Gain-bandwidth product
RL = 2 k
Ω
,,
CL = 100 pF,
5.9
5.9
MHz
Gain-bandwidth product
RL = 2 kΩ,,
f =100 kHz
CL = 100 pF,
5.9 5.9 MHz
BOM
Maximum output-swing
VO(PP) = 20 V,
RL = 2 k
Ω,
668
668
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 20 V,
AVD = 1,
RL = 2 kΩ
,
CL = 100 pF 668 668 kHz
φmPhase margin at unity gain RL = 2 kΩ, CL = 100 pF 58°58°
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
14 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144C electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2144C TLE2144AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 0.5 3.8 0.5 3
mV
VIO Input
offset voltage Full range 4.4 3.6 mV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VO = 2.5 V,
RS = 50 Ω,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VO = 2.5 V,
V
IC
= 2.5 V RS = 50 Ω,25°C8 100 8 100
nA
IIO Input offset current
VIC = 2.5 V
Full range 150 150 nA
IIB
Input bias current
25°C −0.8 −2 −0.8 −2
A
IIB Input bias current Full range −2.1 −2.1 µA
0
−0.3
0
−0.3
25
°
C
0
to
−0.3
to
0
to
−0.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
3
to
3.2
to
3
to
3.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
0
0
V
voltage range
Full range
0
to
0
to
Full range
to
2.9
to
2.9
IOH = −150 A
25°C 3.9 4.1 3.9 4.1
IOH = −150 µAFull range 3.8 3.8
VOH
High-level output
IOH = −1.5 mA
25°C 3.8 4 3.8 4
V
VOH
High-level output
voltage IOH = −1.5 mA Full range 3.7 3.7 V
voltage
IOH = −15 mA
25°C 3.4 3.7 3.4 3.7
IOH = −15 mA Full range 3.4 3.4
IOL = 150 A
25°C 75 125 75 125
IOL = 150 µAFull range 150 150
mV
VOL
Low-level output
IOL = 1.5 mA
25°C 150 225 150 225 mV
VOL
Low-level output
voltage IOL = 1.5 mA Full range 250 250
voltage
IOL = 15 mA
25°C 1.2 1.6 1.2 1.6
V
IOL = 15 mA Full range 1.7 1.7 V
AVD
Large-signal differential
VCC =
±
2.5 V, RL = 2 k
Ω
,
25°C 50 95 50 95
V/mV
AVD
Large-signal differential
voltage amplification
VCC = ±2.5 V, RL = 2 kΩ,
VO = 1 V to −1.5 V Full range 25 25 V/mV
riInput resistance 25°C 70 70 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin,
RS = 50 Ω
25°C 85 118 85 118
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage
rejection ratio
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
rejection ratio
(∆V
CC
± /∆V
IO
)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
ICC
Supply current
VO = 2.5 V,
No load,
25°C 13.2 17.6 13.2 17.6
mA
I
CC
Supply current
VO = 2.5 V,
VIC = 2.5 V
No load,
Full range 18.5 18.5
mA
†Full range is 0°C to 70°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144C operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2144C TLE2144AC
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate A
VD
= −1,
C = 500 pF
R
L
= 2 kن,45 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kن,
42 42 V/µs
ts
Settling time
AVD = −1, To 0.1% 0.16 0.16
s
tsSettling time 2.5-V step To 0.01% 0.22 0.22 µs
Vn
Equivalent input
RS = 20 Ω, f = 10 Hz 15 15
nV/√Hz
Vn
Equivalent input
noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/
√
Hz
VN(PP)
Peak-to-peak equivalent
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent
input noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input
f = 10 Hz 1.92 1.92
pA/√Hz
In
Equivalent input
noise current f = 1 kHz 0.5 0.5
pA/
√
Hz
THD + N
Total harmonic distortion plus
VO = 1 V to 3 V,
RL = 2 k
Ω†
,
0.0052%
0.0052%
THD + N
Total harmonic distortion plus
noise
VO = 1 V to 3 V,
A
VD
= 2,
RL = 2 kن,
f = 10 kHz 0.0052% 0.0052%
B1Unity-gain bandwidth RL = 2 kن,CL = 100 pF 5.9 5.9 MHz
Gain-bandwidth product
RL = 2 k
Ω†
,
CL = 100 pF,
5.8
5.8
MHz
Gain-bandwidth product
RL = 2 kن,
f = 100 kHz
CL = 100 pF,
5.8 5.8 MHz
BOM
Maximum output-swing
VO(PP) = 2 V,
RL = 2 k
Ω†
,
660
660
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 2 V,
A
VD
= 1,
RL = 2 kن,
C
L
= 100 pF 660 660 kHz
φmPhase margin at unity gain RL = 2 kΩ†,CL = 100 pF 57°57°
†RL terminates at 2.5 V
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
16 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144C electrical characteristics at specified free-air temperature, VCC±= ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2144C TLE2144AC
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 0.6 2.4 0.5 1.5
mV
VIO Input
offset voltage Full range 3.2 2.4 mV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VIC = 0,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VIC = 0,
V
O
= 0
RS = 50 Ω,
25°C 7 100 7 100
nA
IIO Input offset current
VO = 0
Full range 150 150 nA
IIB
Input bias current
25°C −0.7 −1.5 −0.7 −1.5
A
IIB Input bias current Full range −1.6 −1.6 µA
−15
−15.3
−15
−15.3
25
°
C
−15
to
−15.3
to
−15
to
−15.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
13
to
13.2
to
13
to
13.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
−15
−15.3
−15
−15
V
voltage range
Full range
−15
to
−15.3
to
−15
to
−15
to
Full range
to
12.9
to
13.1
to
12.9
to
13.1
IO = −150 A
25°C 13.8 14.1 13.8 14.1
IO = −150 µAFull range 13.7 13.7
VOM+
Maximum positive peak
IO = −1.5 mA
25°C 13.7 14 13.7 14
V
VOM+
Maximum positive peak
output voltage swing IO = −1.5 mA Full range 13.6 13.6 V
output voltage swing
IO = −15 mA
25°C 13.1 13.7 13.1 13.7
IO = −15 mA Full range 13 13
IO = 150 A
25°C −14.7 −14.9 −14.7 −14.9
Maximum negative
IO = 150 µAFull range −14.6 −14.6
VOM−
Maximum negative
peak output voltage
IO = 1.5 mA
25°C −14.5 −14.8 −14.5 −14.8
V
VOM−
peak output voltage
swing
IO = 1.5 mA Full range −14.4 −14.4 V
swing
IO = 15 mA
25°C −13.4 −13.8 −13.4 −13.8
IO = 15 mA Full range −13.3 −13.3
AVD
Large-signal differential
VO = ±10 V
25°C 100 170 100 170
V/mV
AVD
Large-signal differential
voltage amplification VO = ±10 V Full range 75 75 V/mV
riInput resistance RL = 2 kΩ25°C 65 65 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin,
RS = 50 Ω
25°C 85 108 85 108
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage
rejection ratio
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
rejection ratio
(∆V
CC
± /∆V
IO
)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
IOS
Short-circuit output
VO = 0
VID = 1 V
25°C
−25 −50 −25 −50
mA
IOS
Short-circuit output
current VO = 0 VID = −1 V 25°C20 31 20 31 mA
ICC
Supply current
VO = 0,
No load
25°C 13.8 18 13.8 18
mA
ICC Supply current VO = 0, No load Full range 18.8 18.8 mA
†Full range is 0°C to 70°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144C operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2144C TLE2144AC
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω
,
27 45 27 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kΩ,
27 42 27 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.34 0.34
s
tsSettling time
AVD = −1,
10-V step To 0.01% 0.4 0.4 µs
Vn
Equivalent input noise voltage
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/
√
Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.89 1.89
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.47 0.47
pA/
√
Hz
THD + N
Total harmonic distortion plus
VO(PP) = 20 V,
RL = 2 k
Ω
,
0.01%
0.01%
THD + N
Total harmonic distortion plus
noise
VO(PP) = 20 V,
A
VD
= 10,
RL = 2 kΩ,
f = 10 kHz 0.01% 0.01%
B1Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz
Gain-bandwidth product
RL = 2 k
Ω
,
CL = 100 pF,
5.9
5.9
MHz
Gain-bandwidth product
RL = 2 kΩ,
f = 100 kHz
CL = 100 pF,
5.9 5.9 MHz
BOM
Maximum output-swing
VO(PP) = 20 V,
RL = 2 k
Ω
,
668
668
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 20 V,
A
VD
= 1,
RL = 2 kΩ,
C
L
= 100 pF 668 668 kHz
φmPhase margin at unity gain RL = 2 kΩ, CL = 100 pF 58°58°
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
18 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141I electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2141I TLE2141AI
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 225 1400 200 1000
V
VIO Input
offset voltage Full range 1900 1500 µV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VO = 2.5 V,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VO = 2.5 V,
VIC = 2.5 V
RS = 50 Ω,
25°C 8 100 8 100
nA
IIO Input offset current
VIC = 2.5 V
Full range 200 200 nA
IIB
Input bias current
25°C −0.8 −2 −0.8 −2
A
IIB Input bias current Full range −2.2 −2.2 µA
0
−0.3
0
−0.3
25
°
C
0
to
−0.3
to
0
to
−0.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
3
to
3.2
to
3
to
3.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
0
−0.3
0
−0.3
V
voltage range
Full range
0
to
−0.3
to
0
to
−0.3
to
Full range
to
2.7
to
2.9
to
2.7
to
2.9
IOH = −150 µA 3.9 4.1 3.9 4.1
IOH = −1.5 mA 25°C3.8 4 3.8 4
VOH
High-level output voltage
IOH = −15 mA
25 C
3.2 3.7 3.2 3.7
V
VOH High-level output voltage IOH = −100 µA3.8 3.8 V
IOH = −1 mA Full range 3.7 3.7
IOH = −10 mA
Full range
3.3 3.3
IOL = 150 µA 75 125 75 125
mV
IOL = 1.5 µA25°C150 225 150 225 mV
VOL
Low-level output voltage
IOL = 15 mA
25 C
1.2 1.6 1.2 1.6 V
VOL Low-level output voltage IOL = 100 µA175 175
mV
IOL = 1 mA Full range 225 225 mV
IOL = 10 mA
Full range
1.4 1.4 V
AVD
Large-signal differential
VCC =
±
2.5 V, RL = 2 k
Ω
,
25°C 50 220 50 220
V/mV
AVD
Large-signal differential
voltage amplification
VCC = ±2.5 V, RL = 2 kΩ,
VO = 1 V to −1.5 V Full range 10 10 V/mV
riInput resistance 25°C 70 70 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin, RS = 50 Ω
25°C 85 118 85 118
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejection
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejection
ratio (∆VCC± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
ICC
Supply current
VO = 2.5 V,
No load,
25°C 3.4 4.4 3.4 4.4
mA
I
CC
Supply current
VO = 2.5 V,
VIC = 2.5 V
No load,
Full range 4.6 4.6
mA
†Full range is −40°C to 105°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141I operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2141I TLE2141AI
UNIT
PARAMETER
TEST CONDITIONS MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω†
,
45 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kن,
42 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.16 0.16
s
tsSettling time
AVD = −1,
2.5-V step To 0.01% 0.22 0.22 µs
Vn
Equivalent input noise voltage
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.92 1.92
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.5 0.5
pA/√Hz
THD + N
Total harmonic distortion plus
VO = 1 V to 3 V,
RL = 2 k
Ω†
,
0.0052%
0.0052%
THD + N
Total harmonic distortion plus
noise
VO = 1 V to 3 V,
A
VD
= 2,
RL = 2 kن,
f = 10 kHz 0.0052% 0.0052%
B1Unity-gain bandwidth RL = 2 kΩ†, CL = 100 pF†5.9 5.9 MHz
Gain-bandwidth product
RL = 2 k
Ω†
CL = 100 pF
†
,
5.8
5.8
MHz
Gain-bandwidth product
RL = 2 kن
f = 100 kHz
CL = 100 pF†,
5.8 5.8 MHz
BOM Maximum output-swing
bandwidth VO(PP) = 2 V,
AVD = 1, RL = 2 kن,
CL = 100 pF†660 660 kHz
φmPhase margin at unity gain RL = 2 kΩ†, CL = 100 pF†57°57°
†RL and CL terminated to 2.5 V.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
20 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141I electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2141I TLE2141AI
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 200 900 175 500
V
VIO Input
offset voltage Full range 1500 1000 µV
VIO
Temperature coefficient of
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient of
input offset voltage
VIC = 0,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VIC = 0,
VO = 0
RS = 50 Ω,
25°C 7 100 7 100
nA
IIO Input offset current
VO = 0
Full range 200 200 nA
IIB
Input bias current
25°C −0.7 −1.5 −0.7 −1.5
A
IIB Input bias current Full range −1.7 −1.7 µA
−15
−15.3
−15
−15.3
25
°
C
−15
to
−15.3
to
−15
to
−15.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
13
to
13.2
to
13
to
13.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
−15
−15.3
−15
−15.3
V
voltage range
Full range
−15
to
−15.3
to
−15
to
−15.3
to
Full range
to
12.7
to
12.9
to
12.7
to
12.9
IO = −150 µA 13.8 14.1 13.8 14.1
IO = −1.5 mA25°C13.7 14 13.7 14
VOM+
Maximum positive peak
IO = −15 mA
25 C
13.1 13.7 13.1 13.7
V
VOM+
Maximum positive peak
output voltage swing IO = −100 µA13.7 13.7 V
output voltage swing
IO = −1 mA Full range 13.6 13.6
IO = −10 mA
Full range
13.1 13.1
IO = 150 µA −14.7 −14.9 −14.7 −14.9
IO = 1.5 mA 25°C−14.5 −14.8 −14.5 −14.8
VOM−
Maximum negative peak
IO = 15 mA
25 C
−13.4 −13.8 −13.4 −13.8
V
VOM−
Maximum negative peak
output voltage swing IO = 100 µA−14.6 −14.6 V
output voltage swing
IO = 1 mA Full range −14.5 −14.5
IO = 10 mA
Full range
−13.4 −13.4
AVD
Large-signal differential
VO = ±10 V,
RL = 2 kΩ
25°C 100 450 100 450
V/mV
AVD
Large-signal differential
voltage amplification VO = ±10 V, RL = 2 kΩFull range 40 40 V/mV
riInput resistance 25°C 65 65 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin, RS = 50 Ω
25°C 85 108 85 108
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejection
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejection
ratio (∆VCC± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
IOS
Short-circuit output
VO = 0
VID = 1 V
25°C
−25 −50 −25 −50
mA
IOS
Short-circuit output
current VO = 0 VID = −1 V 25°C20 31 20 31 mA
ICC
Supply current
VO = 0,
No load
25°C 3.5 4.5 3.5 4.5
mA
I
CC
Supply current
V
O
= 0,
No load
Full range 4.7 4.7
mA
†Full range is −40°C to 105°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141I operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2141I TLE2141AI
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω
,
27 45 27 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kΩ,
27 42 27 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.34 0.34
s
tsSettling time
AVD = −1,
10-V step To 0.01% 0.4 0.4 µs
Vn
Equivalent input noise voltage
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.89 1.89
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.47 0.47
pA/√Hz
THD + N
Total harmonic distortion plus
VO(PP) = 20 V,
RL = 2 k
Ω
,
0.01%
0.01%
THD + N
Total harmonic distortion plus
noise
VO(PP) = 20 V,
AVD = 10,
RL = 2 kΩ,
f = 10 kHz 0.01% 0.01%
B1
Unity-gain bandwidth
RL = 2 kΩ,
CL = 100 pF
6
6
MHz
B
1
Unity-gain bandwidth R
L
= 2 kΩ, C
L
= 100 pF 6 6 MHz
Gain-bandwidth product
RL = 2 k
Ω
,
CL = 100 pF,
5.9
5.9
MHz
Gain-bandwidth product
RL = 2 kΩ,
f = 100 kHz
CL = 100 pF,
5.9 5.9 MHz
BOM
Maximum output-swing
VO(PP) = 20 V,
RL = 2 k
Ω
,
668
668
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 20 V,
AVD = 1,
RL = 2 kΩ,
CL = 100 pF 668 668 kHz
φmPhase margin at unity gain RL = 2 kΩ, CL = 100 pF 58°58°
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
22 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142I electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2142I TLE2142AI
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 220 1900 220 1500
V
VIO Input offset voltage Full range 2400 2000 µV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VO = 2.5 V,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VO = 2.5 V,
VIC = 2.5 V
RS = 50 Ω
,25°C 8 100 8 100
nA
IIO Input offset current
VIC = 2.5 V
Full range 200 200 nA
IIB
Input bias current
25°C −0.8 −2 −0.8 −2
A
IIB Input bias current Full range −2.2 −2.2 µA
0
−0.3
0
−0.3
25
°
C
0
to
−0.3
to
0
to
−0.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
3
to
3.2
to
3
to
3.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
0
−0.3
0
−0.3
V
voltage range
Full range
0
to
−0.3
to
0
to
−0.3
to
Full range
to
2.7
to
2.9
to
2.7
to
2.9
IOH = −150 µA 3.9 4.1 3.9 4.1
IOH = −1.5 mA 25°C 3.8 4 3.8 4
VOH
High-level output voltage
IOH = −15 mA 3.4 3.7 3.4 3.7
V
VOH High-level output voltage IOH = 100 µA3.8 3.8 V
IOH = 1 mA Full range 3.7 3.7
IOH = 10 mA 3.5 3.5
IOl = 150 µA 75 125 75 125
mV
IOL = 1.5 mA 25°C 150 225 150 225 mV
VOL
Low-level output voltage
IOL = 15 mA 1.2 1.4 1.2 1.4 V
VOL Low-level output voltage IOL = 100 µA175 175
mV
IOL = 1 mA Full range 225 225 mV
IOL = 10 mA 1.2 1.2 V
AVD
Large-signal differential
VIC =
±
2.5 V, RL = 2 k
Ω
,
25°C 50 220 50 220
V/mV
AVD
Large-signal differential
voltage amplification
VIC = ±2.5 V, RL = 2 kΩ,
VO = 1 V to −1.5 V Full range 10 10 V/mV
riInput resistance 25°C 70 70 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode rejection
VIC = VICRmin, RS = 50 Ω
25°C 85 118 85 118
dB
CMRR
Common-mode rejection
ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejection
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejection
ratio (∆VCC± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
ICC
Supply current
VO = 2.5 V,
No load,
25°C 6.6 8.8 6.6 8.8
mA
I
CC
Supply current
VO = 2.5 V,
VIC = 2.5 V
No load,
Full range 9.2 9.2
mA
†Full range is − 40°C to 105°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
23
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142I operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2142I TLE2142AI
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω†
,
45 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kن,
42 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.16 0.16
s
tsSettling time
AVD = −1,
2.5-V step To 0.01% 0.22 0.22 µs
Vn
Equivalent input noise
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
Vn
Equivalent input noise
voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent
input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise
f = 10 Hz 1.92 1.92
pA/√Hz
In
Equivalent input noise
current f = 1 kHz 0.5 0.5
pA/√Hz
THD + N
Total harmonic distortion
VO = 1 V to 3 V,
RL = 2 k
Ω†
,
0.0052%
0.0052%
THD + N
Total harmonic distortion
plus noise
VO = 1 V to 3 V,
A
VD
= 2,
RL = 2 kن,
f = 10 kHz 0.0052% 0.0052%
B1Unity-gain bandwidth RL = 2 kن,CL = 100 pF 5.9 5.9 MHz
Gain-bandwidth product
RL = 2 k
Ω†
,
CL = 100 pF,
5.8
5.8
MHz
Gain-bandwidth product
RL = 2 kن,
f = 100 kHz
CL = 100 pF,
5.8 5.8 MHz
BOM
Maximum output-swing
VO(PP) = 2 V,
RL = 2 k
Ω†
,
660
660
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 2 V,
A
VD
= 1,
RL = 2 kن,
C
L
= 100 pF 660 660 kHz
φmPhase margin at unity gain RL = 2 kΩ†, CL = 100 pF 57°57°
†RL terminates at 2.5 V.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
24 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142I electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2142I TLE2142I
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 290 1200 275 750
V
VIO Input offset voltage Full range 1800 1400 µV
VIO
Temperature coefficient of
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient of
input offset voltage
VIC = 0,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VIC = 0,
VO = 0
RS = 50 Ω
,25°C 7 100 7 100
nA
IIO Input offset current
VO = 0
Full range 200 200 nA
IIB
Input bias current
25°C −0.7 −1.5 −0.7 −1.5
A
IIB Input bias current Full range −1.7 −1.7 µA
−15
−15.3
−15
−15.3
25
°
C
−15
to
−15.3
to
−15
to
−15.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
13
to
13.2
to
13
to
13.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
−15
−15.3
−15
−15.3
V
voltage range
Full range
−15
to
−15.3
to
−15
to
−15.3
to
Full range
to
12.7
to
12.9
to
12.7
to
12.9
IO = −150 µA 13.8 14.1 13.8 14.1
IO = −1.5 mA 25°C13.7 14 13.7 14
VOM+
Maximum positive peak
IO = −15 mA
25 C
13.3 13.7 13.3 13.7
V
VOM+
Maximum positive peak
output voltage swing IO = −100 µA13.7 13.7 V
output voltage swing
IO = −1 mA Full range 13.6 13.6
IO = −10 mA
Full range
13.3 13.3
IO = 150 µA −14.7 −14.9 −14.7 −14.9
IO = 1.5 mA 25°C−14.5 −14.8 −14.5 −14.8
VOM−
Maximum negative peak
IO = 15 mA
25 C
−13.4 −13.8 −13.4 −13.8
V
VOM−
Maximum negative peak
output voltage swing IO = 100 µA−14.6 −14.6 V
output voltage swing
IO = 1 mA Full range −14.5 −14.5
IO = 10 mA
Full range
−13.4 −13.4
AVD
Large-signal differential
VO = ±10 V,
RL = 2 kΩ
25°C 100 450 100 450
V/mV
AVD
Large-signal differential
voltage amplification VO = ±10 V
,
RL = 2 kΩFull range 40 40 V/mV
riInput resistance 25°C 65 65 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output imped-
ance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode rejection
VIC = VICRmin 25°C 85 108 85 108
dB
CMRR
Common-mode rejection
ratio RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejection
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejection
ratio (∆VCC± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
IOS
Short-circuit output current
VO = 0
VID = 1 V
25°C
−25 −50 −25 −50
mA
IOS Short-circuit output current VO = 0 VID = −1 V 25°C20 31 20 31 mA
ICC
Supply current
VO = 0,
No load
25°C 6.9 9 6.9 9
mA
ICC Supply current VO = 0, No load Full range 9.4 9.4 mA
†Full range is −40°C to 105°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
25
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142I operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2142I TLE2142AI
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω
,
30 45 30 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kΩ,
30 42 30 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.34 0.34
s
tsSettling time
AVD = −1,
10-V step To 0.01% 0.4 0.4 µs
Vn
Equivalent input noise voltage
RS = 20 Ω, f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.89 1.89
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.47 0.47
pA/√Hz
THD + N
Total harmonic distortion plus
VO(PP) = 20 V,
RL = 2 k
Ω,
0.01%
0.01%
THD + N
Total harmonic distortion plus
noise
VO(PP) = 20 V,
AVD = 10,
RL = 2 kΩ
,
f = 10 kHz 0.01% 0.01%
B1Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz
Gain-bandwidth product
RL = 2 k
Ω
,
CL = 100 pF,
5.9
5.9
MHz
Gain-bandwidth product
RL = 2 kΩ,
f =100 kHz
CL = 100 pF,
5.9 5.9 MHz
BOM
Maximum output-swing
VO(PP) = 20 V,
RL = 2 k
Ω,
668
668
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 20 V,
AVD = 1,
RL = 2 kΩ
,
CL = 100 pF 668 668 kHz
φmPhase margin at unity gain RL = 2 kΩ, CL = 100 pF 58°58°
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
26 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144I electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2144I TLE2144AI
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 0.5 3.8 0.5 3
mV
VIO Input
offset voltage Full range 4.8 4 mV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VIC = 0,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VIC = 0,
V
O
= 0
RS = 50 Ω,
25°C 8 100 8 100
nA
IIO Input offset current
VO = 0
Full range 200 200 nA
IIB
Input bias current
25°C −0.8 −2 −0.8 −2
A
IIB Input bias current Full range −2.2 −2.2 µA
0
−0.3
0
−0.3
25
°
C
0
to
−0.3
to
0
to
−0.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
3
to
3.2
to
3
to
3.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
0
−0.3
0
−0.3
V
voltage range
Full range
0
to
−0.3
to
0
to
−0.3
to
Full range
to
2.7
to
2.9
to
2.7
to
2.9
IOH = −150 µA 3.9 4.1 3.9 4.1
IOH = −1.5 mA 25°C 3.8 4 3.8 4
VOH
High-level
IOH = −15 mA 3.4 3.7 3.4 3.7
V
VOH
High-level
output voltage IOH = 100 µA 3.8 3.8 V
output voltage
IOH = 1 mA Full range 3.7 3.7
IOH = 10 mA 3.5 3.5
IOL = 150 µA 75 125 75 125
mV
IOL = 1.5 µA 25°C 150 225 150 225 mV
VOL
Low-level
IOL = 15 mA 1.2 1.6 1.2 1.6 V
VOL
Low-level
output voltage IOL = 100 µA175 175
mV
output voltage
IOL = 1 mA Full range 225 225 mV
IOL = 10 mA 1.4 1.4 V
AVD
Large-signal differential
VIC =
±
2.5 V, RL = 2 k
Ω
,
25°C 50 95 50 95
V/mV
AVD
Large-signal differential
voltage amplification
VIC = ±2.5 V, RL = 2 kΩ,
VO = 1 V to −1.5 V Full range 10 10 V/mV
riInput resistance 25°C 70 70 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin, RS = 50 Ω
25°C 85 118 85 118
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage
rejection ratio
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
rejection ratio
(∆V
CC
± /∆V
IO
)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
ICC
Supply current
VO = 2.5 V,
No load,
25°C 13.2 17.6 13.2 17.6
mA
I
CC
Supply current
VO = 2.5 V,
VIC = 2.5 V
No load,
Full range 18.4 18.4
mA
†Full range is −40°C to 105°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
27
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144I operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2144I TLE2144AI
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω†
,
45 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kن,
42 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.16 0.16
s
tsSettling time
AVD = −1,
2.5-V step To 0.01% 0.22 0.22 µs
Vn
Equivalent input noise voltage
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/
√
Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.92 1.92
pA/√Hz
InEquivalent input noise current f = 10 kHz 0.5 0.5
pA/
√
Hz
THD + N
Total harmonic distortion plus
VO = 1 V to 3 V,
RL = 2 k
Ω†
,
0.0052%
0.0052%
THD + N
Total harmonic distortion plus
noise
VO = 1 V to 3 V,
AVD = 2,
RL = 2 kن,
f = 10 kHz 0.0052% 0.0052%
B1Unity-gain bandwidth RL = 2 kن,CL = 100 pF 5.9 5.9 MHz
Gain-bandwidth product
RL = 2 k
Ω†
,
CL = 100 pF,
5.8
5.8
MHz
Gain-bandwidth product
RL = 2 kن,
f = 100 kHz
CL = 100 pF,
5.8 5.8 MHz
BOM
Maximum output-swing
VO(PP) = 2 V,
RL = 2 k
Ω†
,
660
660
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 2 V,
A
VD
= 1,
RL = 2 kن,
C
L
= 100 pF 660 660 kHz
φmPhase margin at unity gain RL = 2 kΩ†,CL = 100 pF 57°57°
†RL terminates at 2.5 V
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
28 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144I electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2144I TLE2144AI
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 0.6 2.4 0.5 1.5
mV
VIO Input
offset voltage Full range 3.2 2.8 mV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VIC = 0,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VIC = 0,
V
O
= 0
RS = 50 Ω,
25°C 7 100 7 100
nA
IIO Input offset current
VO = 0
Full range 200 200 nA
IIB
Input bias current
25°C −0.7 −1.5 −0.7 −1.5
A
IIB Input bias current Full range −1.7 −1.7 µA
−15
−15.3
−15
−15.3
25
°
C
−15
to
−15.3
to
−15
to
−15.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
13
to
13.2
to
13
to
13.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
−15
−15.3
−15
−15.3
V
voltage range
Full range
−15
to
−15.3
to
−15
to
−15.3
to
Full range
to
12.7
to
12.9
to
12.7
to
12.9
IO = −150 µA 13.8 14.1 13.8 14.1
IO = −1.5 mA25°C13.7 14 13.7 14
VOM+
Maximum positive peak
IO = −15 mA
25 C
13.1 13.7 13.1 13.7
V
VOM+
Maximum positive peak
output voltage swing IO = −100 µA 13.7 13.7 V
output voltage swing
IO = −1 mA Full range 13.6 13.6
IO = −10 mA
Full range
13.1 13.1
IO = 150 µA −14.7 −14.9 −14.7 −14.9
Maximum negative
IO = 1.5 mA 25°C−14.5 −14.8 −14.5 −14.8
VOM−
Maximum negative
peak output voltage
IO = 15 mA
25 C
−13.4 −13.8 −13.4 −13.8
V
VOM−
peak output voltage
swing
IO = 100 µA −14.6 −14.6 V
swing
IO = 1 mA Full range −14.5 −14.5
IO = 10 mA
Full range
−13.4 −13.4
AVD
Large-signal differential
VO = ±10 V,
RL = 2 kΩ
25°C 100 170 100 170
V/mV
AVD
Large-signal differential
voltage amplification VO = ±10 V, RL = 2 kΩFull range 40 40 V/mV
riInput resistance 25°C 65 65 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop
output impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin,
RS = 50 Ω
25°C 85 108 85 108
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage
rejection ratio
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
rejection ratio
(∆V
CC
± /∆V
IO
)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
IOS
Short-circuit output
VO = 0
VID = 1 V
25°C
−25 −50 −25 −50
mA
IOS
Short-circuit output
current VO = 0 VID = −1 V 25°C20 31 20 31 mA
ICC
Supply current
VO = 0,
No load
25°C 13.8 18 13.8 18
mA
I
CC
Supply current
V
O
= 0,
No load
Full range 18.8 18.8
mA
†Full range is −40°C to 105°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
29
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144I operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2144I TLE2144AI
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω
,
27 45 27 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kΩ,
27 42 27 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.34 0.34
s
tsSettling time
AVD = −1,
10-V step To 0.01% 0.4 0.4 µs
Vn
Equivalent input
RS = 20 Ω, f = 10 Hz 15 15
nV/√Hz
Vn
Equivalent input
noise voltage RS = 20 Ω,f = 1 kHz 10.5 10.5
nV/
√
Hz
VN(PP)
Peak-to-peak equivalent
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent
input noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input
f = 10 Hz 1.89 1.89
pA/√Hz
In
Equivalent input
noise current f = 1 kHz 0.47 0.47
pA/
√
Hz
THD + N
Total harmonic distortion plus
VO(PP) = 20 V,
RL = 2 k
Ω
,
0.01%
0.01%
THD + N
Total harmonic distortion plus
noise
VO(PP) = 20 V,
A
VD
= 10,
RL = 2 kΩ,
f = 10 kHz 0.01% 0.01%
B1Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz
Gain-bandwidth product
RL = 2 k
Ω
,
CL = 100 pF,
5.9
5.9
MHz
Gain-bandwidth product
RL = 2 kΩ,
f = 100 kHz
CL = 100 pF,
5.9 5.9 MHz
BOM
Maximum output-swing
VO(PP) = 20 V,
RL = 2 k
Ω
,
668
668
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 20 V,
A
VD
= 1,
RL = 2 kΩ,
C
L
= 100 pF 668 668 kHz
φmPhase margin at unity gain RL = 2 kΩ, CL = 100 pF 58°58°
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
30 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141M electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2141M TLE2141AM
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 225 1400 200 1000
V
VIO Input
offset voltage Full range 2100 1700 µV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VO = 2.5 V
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VO = 2.5 V
VIC = 2.5 V
RS = 50 Ω,
25°C 8 100 8 100
nA
IIO Input offset current
VIC = 2.5 V
Full range 250 250 nA
IIB
Input bias current
25°C −0.8 −2 −0.8 −2
A
IIB Input bias current Full range −2.3 −2.3 µA
0
−0.3
0
−0.3
25
°
C
0
to
−0.3
to
0
to
−0.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
3
to
3.2
to
3
to
3.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
0
−0.3
0
−0.3
V
voltage range
Full range
0
to
−0.3
to
0
to
−0.3
to
Full range
to
2.7
to
2.9
to
2.7
to
2.9
IOH = −150 µA 3.9 4.1 3.9 4.1
IOH = −1.5 mA 25°C3.8 4 3.8 4
VOH
High-level output
IOH = −15 mA
25 C
3.2 3.7 3.2 3.7
V
VOH
High-level output
voltage IOH = −100 µA3.75 3.75 V
voltage
IOH = −1 mA Full range 3.65 3.65
IOH = −10 mA
Full range
3.25 3.25
IOL = 150 µA 75 125 75 125
mV
IOL = 1.5 µA25°C150 225 150 225 mV
VOL
Low-level output
IOL = 15 mA
25 C
1.2 1.4 1.2 1.4 V
VOL
Low-level output
voltage IOL = 100 µA200 200
mV
voltage
IOL = 1 mA Full range 250 225 mV
IOL = 10 mA
Full range
1.25 1.25 V
AVD
Large-signal differential
VIC =
±
2.5 V, RL = 2 k
Ω, 25°C 50 220 50 220
V/mV
AVD
Large-signal differential
voltage amplification
VIC = ±2.5 V, RL = 2 kΩ
,
VO = 1 V to −1.5 V Full range 5 5 V/mV
riInput resistance 25°C 70 70 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop
output impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin, RS = 50 Ω
25°C 85 118 85 118
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejection
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejection
ratio (∆VCC± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
ICC
Supply current
VO = 2.5 V,
No load,
25°C 3.4 4.4 3.4 4.4
mA
I
CC
Supply current
VO = 2.5 V,
VIC = 2.5 V
No load,
Full range 4.6 4.6
mA
†Full range is −55°C to 125°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
31
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141M operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2141M TLE2141AM
UNIT
PARAMETER
TEST CONDITIONS MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω†
,
45 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kن,
42 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.16 0.16
s
tsSettling time
AVD = −1,
2.5-V step To 0.01% 0.22 0.22 µs
Vn
Equivalent input noise voltage
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.92 1.92
pA/√Hz
InEquivalent input noise curren
t
f = 1 kHz 0.5 0.5
pA/√Hz
THD + N Total harmonic distortion
plus noise VO = 1 V to 3 V,
AVD = 2, RL = 2 kن,
f = 10 kHz 0.0052% 0.0052%
B1Unity-gain bandwidth RL = 2 kΩ†, CL = 100 pF†5.9 5.9 MHz
Gain-bandwidth product RL = 2 kن,
f = 100 kHz CL = 100 pF†,5.8 5.8 MHz
BOM Maximum output-swing
bandwidth VO(PP) = 2 V,
AVD = 1 RL = 2 kن,660 660 kHz
φmPhase margin at unity gain RL = 2 kΩ†, CL = 100 pF†57°57°
†RL and CL terminated to 2.5 V.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
32 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141M electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2141M TLE2141AM
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 200 900 175 500
V
VIO Input
offset voltage Full range 1700 1200 µV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VIC = 0,
RS = 50 Ω
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VIC = 0, RS = 50 Ω25°C7 100 7 100
nA
IIO Input offset current Full range 250 250 nA
IIB
Input bias current
25°C −0.7 −1.5 −0.7 −1.5
A
IIB Input bias current Full range −1.8 −1.8 µA
−15
−15.3
−15
−15.3
25
°
C
−15
to
−15.3
to
−15
to
−15.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
13
to
13.2
to
13
to
13.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
−15
−15.3
−15
−15.3
V
voltage range
Full range
−15
to
−15.3
to
−15
to
−15.3
to
Full range
to
12.7
to
12.9
to
12.7
to
12.9
IO = −150 µA 13.8 14.1 13.8 14.1
IO = −1.5 mA25°C13.7 14 13.7 14
VOM+
Maximum positive peak
IO = −15 mA
25 C
13.1 13.7 13.1 13.7
V
VOM+
Maximum positive peak
output voltage swing IO = −100 µA13.7 13.7 V
output voltage swing
IO = −1 mA Full range 13.6 13.6
IO = −10 mA
Full range
13.1 13.1
IO = 150 µA −14.7 −14.9 −14.7 −14.9
IO = 1.5 mA 25°C−14.5 −14.8 −14.5 −14.8
VOM−
Maximum negative peak
IO = 15 mA
25 C
−13.4 −13.8 −13.4 −13.8
V
VOM−
Maximum negative peak
output voltage swing IO = 100 µA−14.6 −14.6 V
output voltage swing
IO = 1 mA Full range −14.5 −14.5
IO = 10 mA
Full range
−13.4 −13.4
AVD
Large-signal differential
VO = ±10 V,
RL = 2 kΩ
25°C 100 450 100 450
V/mV
AVD
Large-signal differential
voltage amplification VO = ±10 V, RL = 2 kΩFull range 20 20 V/mV
riInput resistance 25°C 65 65 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin,
RS = 50 Ω
25°C 85 108 85 108
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin
,
RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejection
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejection
ratio (∆VCC± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
IOS
Short-circuit output
VO = 0
VID = 1 V
25°C
−25 −50 −25 −50
mA
IOS
Short-circuit output
current VO = 0 VID = −1 V 25°C20 31 20 31 mA
ICC
Supply current
VO = 0,
No load,
25°C 3.5 4.5 3.5 4.5
mA
I
CC
Supply current
VO = 0,
VIC = 2.5 V
No load,
Full range 4.7 4.7
mA
†Full range is −55°C to 125°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
33
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141M operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2141M TLE2141AM
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω
,
27 45 27 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 100 pF
RL = 2 kΩ,
27 42 27 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.34 0.34
s
tsSettling time
AVD = −1,
10-V step To 0.01% 0.4 0.4 µs
Vn
Equivalent input noise voltage
RS = 20 Ω, f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.89 1.89
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.47 0.47
pA/√Hz
THD + N
Total harmonic distortion plus
VO(PP) = 20 V,
RL = 2 k
Ω
,
0.01%
0.01%
THD + N
Total harmonic distortion plus
noise
VO(PP) = 20 V,
AVD = 10,
RL = 2 kΩ,
f = 10 kHz 0.01% 0.01%
B1
Unity-gain bandwidth
RL = 2 kΩ,
CL = 100 pF
6
6
MHz
B
1
Unity-gain bandwidth R
L
= 2 kΩ, C
L
= 100 pF 6 6 MHz
Gain-bandwidth product
RL = 2 k
Ω
,
CL = 100 pF,
5.9
5.9
MHz
Gain-bandwidth product
RL = 2 kΩ,
f = 100 kHz
CL = 100 pF,
5.9 5.9 MHz
BOM
Maximum output-swing
VO(PP) = 20 V,
RL = 2 k
Ω
,
668
668
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 20 V,
AVD = 1,
RL = 2 kΩ,
CL = 100 pF 668 668 kHz
φmPhase margin at unity gain RL = 2 kΩ, CL = 100 pF 58°58°
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
34 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142M electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2142M TLE2142AM
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 220 1900 200 1500
V
VIO Input offset voltage Full range 2600 2200 µV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VO = 2.5 V,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VO = 2.5 V,
VIC = 2.5 V
RS = 50 Ω,
25°C 8 100 8 100
nA
IIO Input offset current
VIC = 2.5 V
Full range 200 200 nA
IIB
Input bias current
25°C −0.8 −2 −0.8 −2
A
IIB Input bias current Full range −2.3 −2.3 µA
0
−0.3
0
−0.3
25
°
C
0
to
−0.3
to
0
to
−0.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
3
to
3.2
to
3
to
3.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
0
−0.3
0
−0.3
V
voltage range
Full range
0
to
−0.3
to
0
to
−0.3
to
Full range
to
2.7
to
2.9
to
2.7
to
2.9
IOH = −150 µA 3.9 4.1 3.9 4.1
IOH = −1.5 mA 25°C3.8 4 3.8 4
VOH
High-level output
IOH = −15 mA
25 C
3.4 3.7 3.4 3.7
V
VOH
High-level output
voltage IOH = 100 µA3.75 3.75 V
voltage
IOH = 1 mA Full range 3.65 3.65
IOH = 10 mA
Full range
3.45 3.45
IOL = 150 µA 75 125 75 125
mV
IOL = 1.5 mA 25°C150 225 150 225 mV
VOL
Low-level output
IOL = 15 mA
25 C
1.2 1.4 1.2 1.4 V
VOL
Low-level output
voltage IOL = 100 µA200 200
mV
voltage
IOL = 1 mA Full range 250 250 mV
IOL = 10 mA
Full range
1.25 1.25 V
AVD
Large-signal differential
VIC =
±
2.5 V, RL = 2 k
Ω
,
25°C 50 220 50 220
V/mV
AVD
Large-signal differential
voltage amplification
VIC = ±2.5 V, RL = 2 kΩ,
VO = 1 V to −1.5 V Full range 5 5 V/mV
riInput resistance 25°C 70 70 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin, RS = 50 Ω
25°C 85 118 85 118
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejec-
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejec-
tion ratio (∆VCC± /∆VIO
)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
ICC
Supply current
VO = 2.5 V,
No load,
25°C 6.6 8.8 6.6 8.8
mA
ICC Supply current
VO = 2.5 V,
VIC = 2.5 V
No load,
Full range 9.2 9.2 mA
†Full range is − 55°C to 125°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
35
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142M operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2142M TLE2142AM
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω†
,
45 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kن,
42 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.16 0.16
s
tsSettling time
AVD = −1,
2.5-V step To 0.01% 0.22 0.22 µs
Vn
Equivalent input noise volt-
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
Vn
Equivalent input noise volt-
age RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent
input noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise cur-
f = 10 Hz 1.92 1.92
pA/√Hz
In
Equivalent input noise cur-
rent f = 1 kHz 0.5 0.5
pA/√Hz
THD + N
Total harmonic distortion
VO = 1 V to 3 V,
RL = 2 k
Ω†
,
0.0052%
0.0052%
THD + N
Total harmonic distortion
plus noise
VO = 1 V to 3 V,
AVD = 2,
RL = 2 kن,
f = 10 kHz 0.0052% 0.0052%
B1Unity-gain bandwidth RL = 2 kن,CL = 100 pF 5.9 5.9 MHz
Gain-bandwidth product
RL = 2 k
Ω†
,
CL = 100 pF
5.8
5.8
MHz
Gain-bandwidth product
RL = 2 kن,
f = 100 kHz
CL = 100 pF
5.8 5.8 MHz
BOM
Maximum output-swing
VO(PP) = 2 V,
RL = 2 k
Ω†
,
660
660
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 2 V,
A
VD
= 1,
RL = 2 kن,
C
L
= 100 pF 660 660 kHz
φmPhase margin RL = 2 kΩ†, CL = 100 pF 57°57°
†RL terminates at 2.5 V.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
36 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142M electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2142M TLE2142AM
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 290 1200 275 750
V
VIO Input offset voltage Full range 2000 1600 µV
VIO
Temperature coefficient of
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient of
input offset voltage
VIC = 0,
RS = 50 Ω
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VIC = 0, RS = 50 Ω25°C7 100 7 100
nA
IIO Input offset current Full range 250 250 nA
IIB
Input bias current
25°C −0.7 −1.5 −0.7 −1.5
A
IIB Input bias current Full range −1.8 −1.8 µA
−15
−15.3
−15
−15.3
25
°
C
−15
to
−15.3
to
−15
to
−15.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
13
to
13.2
to
13
to
13.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
−15
−15.3
−15
−15.3
V
voltage range
Full range
−15
to
−15.3
to
−15
to
−15.3
to
Full range
to
12.7
to
12.9
to
12.7
to
12.9
IO = −150 µA 13.8 14.1 13.8 14.1
IO = −1.5 mA 25°C13.7 14 13.7 14
VOM+
Maximum positive peak
IO = −15 mA
25 C
13.3 13.7 13.3 13.7
V
VOM+
Maximum positive peak
output voltage swing IO = −100 µA13.7 13.7 V
output voltage swing
IO = −1 mA Full range 13.6 13.6
IO = −10 mA
Full range
13.3 13.3
IO = 150 µA −14.7 −14.9 −14.7 −14.9
IO = 1.5 mA 25°C−14.5 −14.8 −14.5 −14.8
VOM−
Maximum negative peak
IO = 15 mA
25 C
−13.4 −13.8 −13.4 −13.8
V
VOM−
Maximum negative peak
output voltage swing IO = 100 µA−14.6 −14.6 V
output voltage swing
IO = 1 mA Full range −14.5 −14.5
IO = 10 mA
Full range
−13.4 −13.4
AVD
Large-signal differential
VO = ±10 V,
RL = 2 kΩ
25°C 100 450 100 450
V/mV
AVD
Large-signal differential
voltage amplification VO = ±10 V, RL = 2 kΩFull range 20 20 V/mV
riInput resistance 25°C 65 65 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode rejection
VIC = VICRmin,
25°C 85 108 85 108
dB
CMRR
Common-mode rejection
ratio
VIC = VICRmin,
RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage rejection
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
Supply-voltage rejection
ratio (∆VCC ± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
IOS
Short-circuit output current
VO = 0
VID = 1 V
25°C
−25 −50 −25 −50
mA
IOS Short-circuit output current VO = 0 VID = −1 V 25°C20 31 20 31 mA
ICC
Supply current
VO = 0,
No load,
25°C 6.9 9 6.9 9
mA
ICC Supply current
VO = 0,
VIC = 2.5 V
No load,
Full range 9.4 9.4 mA
†Full range is −55°C to 125°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
37
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142M operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2142M TLE2142AM
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
RL = 2 k
Ω
,
AVD = −1,
27 45 27 45
V/ s
SR− Negative slew rate
RL = 2 kΩ,
CL = 100 pF
AVD = −1,
27 42 27 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.34 0.34
s
tsSettling time
AVD = −1,
10-V step To 0.01% 0.4 0.4 µs
Vn
Equivalent input noise voltage
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.89 1.89
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.47 0.47
pA/√Hz
THD + N
Total harmonic distortion plus
VO(PP) = 20 V,
RL = 2 k
Ω,
0.01%
0.01%
THD + N
Total harmonic distortion plus
noise
VO(PP) = 20 V,
A
VD
= 10,
RL = 2 kΩ
,
f = 10 kHz 0.01% 0.01%
B1Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz
Gain-bandwidth product
RL = 2 k
Ω
,
CL = 100 pF,
5.9
5.9
MHz
Gain-bandwidth product
RL = 2 kΩ,
f = 100 kHz
CL = 100 pF,
5.9 5.9 MHz
BOM
Maximum output-swing band-
VO(PP) = 20 V,
RL = 2 k
Ω
,
668
668
kHz
BOM
Maximum output-swing band-
width
VO(PP) = 20 V,
A
VD
= 1,
RL = 2 kΩ,
C
L
= 100 pF 668 668 kHz
φmPhase margin at unity gain RL = 2 kΩ, CL = 100 pF 58°58°
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
38 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144M electrical characteristics at specified free-air temperature, VCC = 5 V (unless otherwise
noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2144M TLE2144AM
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 0.5 3.8 0.5 3
mV
VIO Input
offset voltage Full range 5.2 4.4 mV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VO = 2.5 V,
RS = 50
Ω
,
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VO = 2.5 V,
V
IC
= 2.5 V
RS = 50 Ω,
25°C 8 100 8 100
nA
IIO Input offset current
VIC = 2.5 V
Full range 250 250 nA
IIB
Input bias current
25°C −0.8 −2 −0.8 −2
A
IIB Input bias current Full range −2.3 −2.3 µA
0
−0.3
0
−0.3
25
°
C
0
to
−0.3
to
0
to
−0.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
3
to
3.2
to
3
to
3.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
0
−0.3
0
−0.3
V
voltage range
Full range
0
to
−0.3
to
0
to
−0.3
to
Full range
to
2.7
to
2.9
to
2.7
to
2.9
IOH = −150 µA 3.9 4.1 3.9 4.1
IOH = −1.5 mA 25°C 3.8 4 3.8 4
VOH
High-level output
IOH = −15 mA 3.4 3.7 3.4 3.7
V
VOH
High-level output
voltage IOH = 100 µA 3.75 3.75 V
voltage
IOH = 1 mA Full range 3.65 3.65
IOH = 10 mA 3.45 3.45
IOL = 150 µA 75 125 75 125
mV
IOL = 1.5 µA 25°C 150 225 150 225 mV
VOL
Low-level output
IOL = 15 mA 1.2 1.6 1.2 1.6 V
VOL
Low-level output
voltage IOL = 100 µA 200 200
mV
voltage
IOL = 1 mA Full range 250 250 mV
IOL = 10 mA 1.45 1.45 V
AVD
Large-signal differential
VIC =
±
2.5 V, RL = 2 k
Ω
,
25°C 50 95 50 95
V/mV
AVD
Large-signal differential
voltage amplification
VIC = ±2.5 V, RL = 2 kΩ,
VO = 1 V to −1.5 V Full range 5 5 V/mV
riInput resistance 25°C 70 70 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin,
RS = 50 Ω
25°C 85 118 85 118
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage
rejection ratio
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
rejection ratio
(∆V
CC
± /∆V
IO
)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
ICC
Supply current
VO = 2.5 V,
No load,
25°C 13.2 17.6 13.2 17.6
mA
I
CC
Supply current
VO = 2.5 V,
VIC = 2.5 V
No load,
Full range 18.4 18.4
mA
†Full range is −55°C to 125°C.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
39
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144M operating characteristics, VCC = 5 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2144M TLE2144AM
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
AVD = −1,
RL = 2 k
Ω†
,
45 45
V/ s
SR− Negative slew rate
AVD = −1,
CL = 500 pF
RL = 2 kن,
42 42 V/µs
ts
Settling time
AVD = −1,
To 0.1% 0.16 0.16
s
tsSettling time
AVD = −1,
2.5-V step To 0.01% 0.22 0.22 µs
Vn
Equivalent input noise voltage
RS = 20 Ω,f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/√Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.92 1.92
pA/√Hz
InEquivalent input noise current f = 1 kHz 0.5 0.5
pA/
√
Hz
THD + N
Total harmonic distortion plus
VO = 1 V to 3 V,
RL = 2 k
Ω†
,
0.0052%
0.0052%
THD + N
Total harmonic distortion plus
noise
VO = 1 V to 3 V,
A
VD
= 2,
RL = 2 kن,
f = 10 kHz 0.0052% 0.0052%
B1
Unity-gain bandwidth
RL = 2 kن,
CL = 100 pF
5.9
5.9
MHz
B
1
Unity-gain bandwidth R
L
= 2 kΩ
†
,C
L
= 100 pF 5.9 5.9 MHz
Gain-bandwidth product
RL = 2 k
Ω†
,
CL = 100 pF,
5.8
5.8
MHz
Gain-bandwidth product
RL = 2 kن,
f = 100 kHz
CL = 100 pF,
5.8 5.8 MHz
BOM
Maximum output-swing
VO(PP) = 2 V,
RL = 2 k
Ω†
,
660
660
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 2 V,
A
VD
= 1
RL = 2 kن,
660 660 kHz
φmPhase margin RL = 2 kΩ†,CL = 100 pF 57°57°
†RL terminates at 2.5 V
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
40 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144M electrical characteristics at specified free-air temperature, VCC± = ±15 V (unless
otherwise noted)
PARAMETER
TEST CONDITIONS
TA†
TLE2144M TLE2144AM
UNIT
PARAMETER
TEST CONDITIONS
T
A
†
MIN TYP MAX MIN TYP MAX
UNIT
VIO
Input offset voltage
25°C 0.6 2.4 0.5 1.5
mV
VIO Input
offset voltage Full range 4 3.2 mV
VIO
Temperature coefficient
Full range
1.7
1.7
V/°C
αVIO
Temperature coefficient
of input offset voltage
VIC = 0,
RS = 50 Ω
Full range 1.7 1.7 µV/°C
IIO
Input offset current
VIC = 0, RS = 50 Ω25°C7 100 7 100
nA
IIO Input offset current Full range 250 250 nA
IIB
Input bias current
25°C −0.7 −1.5 −0.7 −1.5
A
IIB Input bias current Full range −1.8 −1.8 µA
−15
−15.3
−15
−15.3
25
°
C
−15
to
−15.3
to
−15
to
−15.3
to
VICR
Common-mode input
RS = 50 Ω
25 C
to
13
to
13.2
to
13
to
13.2
V
VICR
Common-mode input
voltage range RS = 50 Ω
−15
−15.3
−15
−15.3
V
voltage range
Full range
−15
to
−15.3
to
−15
to
−15.3
to
Full range
to
12.7
to
12.9
to
12.7
to
12.9
IO = −150 µA 13.8 14.1 13.8 14.1
IO = −1.5 mA25°C13.7 14 13.7 14
VOM+
Maximum positive peak
IO = −15 mA
25 C
13.1 13.7 13.1 13.7
V
VOM+
Maximum positive peak
output voltage swing IO = −100 µA 13.7 13.7 V
output voltage swing
IO = −1 mA Full range 13.6 13.6
IO = −10 mA
Full range
13.1 13.1
IO = 150 µA −14.7 −14.9 −14.7 −14.9
V
Maximum negative
IO = 1.5 mA 25°C−14.5 −14.8 −14.5 −14.8 V
VOM−
Maximum negative
peak output voltage
IO = 15 mA
25 C
−13.4 −13.8 −13.4 −13.8
VOM−
peak output voltage
swing
IO = 100 µA −14.6 −14.6
swing
IO = 1 mA Full range −14.5 −14.5
IO = 10 mA
Full range
−13.4 −13.4
AVD
Large-signal differential
VO = ±10 V,
RL = 2 kΩ
25°C 100 170 100 170
V/mV
AVD
Large-signal differential
voltage amplification VO = ±10 V, RL = 2 kΩFull range 20 20 V/mV
riInput resistance 25°C 65 65 MΩ
ciInput capacitance 25°C 2.5 2.5 pF
zoOpen-loop output
impedance f = 1 MHz 25°C 30 30 Ω
CMRR
Common-mode
VIC = VICRmin,
RS = 50 Ω
25°C 85 108 85 108
dB
CMRR
Common-mode
rejection ratio VIC = VICRmin, RS = 50 ΩFull range 80 80 dB
kSVR
Supply-voltage
rejection ratio
VCC± =
±
2.5 V to
±
15 V,
25°C 90 106 90 106
dB
kSVR
rejection ratio
(∆V
CC
± /∆V
IO
)
VCC± = ±2.5 V to ±15 V,
RS = 50 ΩFull range 85 85 dB
IOS
Short-circuit output
VO = 0
VID = 1 V
25°C
−25 −50 −25 −50
mA
IOS
Short-circuit output
current VO = 0 VID = −1 V 25°C20 31 20 31 mA
ICC
Supply current
VO = 0,
No load,
25°C 13.8 18 13.8 18
mA
ICC Supply current
VO = 0,
VIC = 2.5 V
No load,
Full range 18.8 18.8 mA
†Full range is −55°C to 125°C
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
41
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144M operating characteristics, VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2144M TLE2144AM
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX MIN TYP MAX
UNIT
SR+ Positive slew rate
RL = 2 k
Ω
,
AVD = −1,
27 45 27 45
V/ s
SR− Negative slew rate
RL = 2 kΩ,
CL = 100 pF
AVD = −1,
27 42 27 42 V/µs
ts
Settling time
AVD = −1, To 0.1% 0.34 0.34
s
tsSettling time 10-V step To 0.01% .4 .4 µs
Vn
Equivalent input noise voltage
RS = 20 Ω, f = 10 Hz 15 15
nV/√Hz
VnEquivalent input noise voltage RS = 20 Ω, f = 1 kHz 10.5 10.5
nV/
√
Hz
VN(PP)
Peak-to-peak equivalent input
f = 0.1 Hz to 1 Hz 0.48 0.48
V
VN(PP)
Peak-to-peak equivalent input
noise voltage f = 0.1 Hz to 10 Hz 0.51 0.51 µV
In
Equivalent input noise current
f = 10 Hz 1.89 1.89
pA/√Hz
InEquivalent input noise current f = 10 kHz 0.47 0.47
pA/
√
Hz
THD + N
Total harmonic distortion plus
VO(PP) = 20 V,
RL = 2 k
Ω
,
0.01%
0.01%
THD + N
Total harmonic distortion plus
noise
VO(PP) = 20 V,
AVD = 10,
RL = 2 kΩ,
f = 10 kHz 0.01% 0.01%
B1Unity-gain bandwidth RL = 2 kΩ, CL = 100 pF 6 6 MHz
Gain-bandwidth product
RL = 2 k
Ω
,
CL = 100 pF,
5.9
5.9
MHz
Gain-bandwidth product
RL = 2 kΩ,
f = 100 kHz
CL = 100 pF,
5.9 5.9 MHz
BOM
Maximum output-swing
VO(PP) = 20 V,
RL = 2 k
Ω
,
668
668
kHz
BOM
Maximum output-swing
bandwidth
VO(PP) = 20 V,
AVD = 1,
RL = 2 kΩ,
CL = 100 pF 668 668 kHz
φmPhase margin at unity gain RL = 2 kΩ, CL = 100 pF 58°58°
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
42 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2141Y electrical characteristics at specified free-air temperature, VCC± = ±15 V, TA = 25°C
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
TLE2141Y
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX
UNIT
VIO Input offset voltage
VIC = 0,
RS = 50 Ω
200 1000 µV
IIO Input offset current VIC = 0,
VO = 0
RS = 50 Ω, 7 100 nA
IIB Input bias current
VO = 0
−0.7 −1.5 µA
−15
−15.3
VICR
Common-mode input voltage range
RS = 50
Ω
−15
to
−15.3
to
V
VICR
Common-mode input voltage range
RS = 50 Ω
to
13
to
13.2
V
IO = −150 µA 13.8 14.1
V
OM+
Maximum positive peak output voltage swing IO = −1.5 mA13.7 14 V
VOM+
Maximum positive peak output voltage swing
IO = −15 mA 13.3 13.7
V
IO = 150 µA −14.7 −14.9
V
OM−
Maximum negative peak output voltage swing IO = 1.5 mA −14.5 −14.8 V
VOM−
Maximum negative peak output voltage swing
IO = 15 mA −13.4 −13.8
V
AVD
Large-signal differential voltage amplification
VO = ±10 V,
RL = 2 kΩ
100
450
V/mV
A
VD
Large-signal differential voltage amplification V
O
= ±10 V, R
L
= 2 kΩ100 450 V/mV
riInput resistance 65 MΩ
ciInput capacitance 2.5 pF
zoOpen-loop output impedance f = 1 MHz 30 Ω
CMRR Common-mode rejection ratio VIC = VICRmin, RS = 50 Ω80 108 dB
kSVR
Supply-voltage rejection ratio (∆VCC /∆VIO)
VCC± =
±
2.5 V to
±
15 V,
85
106
dB
kSVR Supply-voltage rejection ratio (∆VCC±/∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 Ω85 106 dB
IOS
Short-circuit output current
VO = 0
VID = 1 V −25 −50
mA
IOS Short-circuit output current VO = 0 VID = −1 V 20 31 mA
ICC Supply current VO = 0, No load 3.5 4.5 mA
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
43
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2142Y electrical characteristics at specified free-air temperature, VCC± = ±15 V, TA = 25°C
PARAMETER
TEST CONDITIONS
TLE2142Y
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX
UNIT
VIO Input offset voltage
VIC = 0,
RS = 50 Ω,
150 875 µV
IIO Input offset current VIC = 0,
VO = 0
RS = 50 Ω,7 100 nA
IIB Input bias current
VO = 0
−0.7 −1.5 µA
−15
−15.3
VICR
Common-mode input voltage range
RS = 50
Ω
−15
to
−15.3
to
V
VICR
Common-mode input voltage range
RS = 50 Ω
to
13
to
13.2
V
IO = −150 µA 13.8 14.1
V
OM+
Maximum positive peak output voltage swing IO = −1.5 mA13.7 14 V
VOM+
Maximum positive peak output voltage swing
IO = −15 mA 13.3 13.7
V
IO = 150 µA −14.7 −14.9
V
OM−
Maximum negative peak output voltage swing IO = 1.5 mA −14.5 −14.8 V
VOM−
Maximum negative peak output voltage swing
IO = 15 mA −13.4 −13.8
V
AVD
Large-signal differential voltage amplification
VO = ±10 V,
RL = 2 kΩ
100
450
V/mV
A
VD
Large-signal differential voltage amplification V
O
= ±10 V, R
L
= 2 kΩ100 450 V/mV
riInput resistance 65 MΩ
ciInput capacitance 2.5 pF
zoOpen-loop output impedance f = 1 MHz 30 Ω
CMRR Common-mode rejection ratio VIC = VICRmin, RS = 50 Ω80 108 dB
kSVR
Supply-voltage rejection ratio (∆VCC /∆VIO)
VCC± =
±
2.5 V to
±
15 V,
85
106
dB
kSVR Supply-voltage rejection ratio (∆VCC± /∆VIO)
VCC± = ±2.5 V to ±15 V,
RS = 50 Ω85 106 dB
IOS
Short-circuit output current
VO = 0
VID = 1 V −25 −50
mA
IOS Short-circuit output current VO = 0 VID = −1 V 20 31 mA
ICC Supply current VO = 0, No load 6.9 9 mA
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
44 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2144Y electrical characteristics at VCC± = ±15 V, TA = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
TLE2144Y
UNIT
PARAMETER
TEST CONDITIONS
MIN TYP MAX
UNIT
VIO Input offset voltage 0.3 1.8 mV
IIO Input offset current V
IC
= 0, V
O
= 0 R
S
= 50 Ω, 7 100 nA
IIB Input bias current
VIC = 0, VO = 0
RS = 50 ,
−0.7 −1.5 µA
−15
−15.3
VICR
Common-mode input voltage range
RS = 50
Ω
−15
to
−15.3
to
V
VICR
Common-mode input voltage range
RS = 50 Ω
to
13
to
13.2
V
IO = −150 µA 13.8 14.1
V
OM+
Maximum positive peak output voltage swing IO = −1.5 mA13.7 14 V
VOM+
Maximum positive peak output voltage swing
IO = −15 mA 13.3 13.7
V
IO = 150 µA −14.7 −14.9
V
OM−
Maximum negative peak output voltage swing IO = 1.5 mA −14.5 −14.8 V
VOM−
Maximum negative peak output voltage swing
IO = 15 mA −13.4 −13.8
V
AVD Large-signal dif ferential voltage amplification VO = ±10 V, RL = 2 kΩ100 450 V/mV
riInput resistance 65 MΩ
ciInput capacitance 2.5 pF
zoOpen-loop output impedance f = 1 MHz 30 Ω
CMRR Common-mode rejection ratio VIC = VICRmin, RS = 50 Ω80 108 dB
kSVR Supply-voltage rejection ratio (∆VCC± /∆VIO) VCC± = ±2.5 V to ±15 V, RS = 50 Ω85 106 dB
IOS
Short-circuit output current
VO = 0
VID = 1 V −25 −50
mA
IOS Short-circuit output current VO = 0 VID = −1 V 20 31 mA
ICC Supply current VO = 0, No load 13.8 18 mA
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
45
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO Input offset voltage Distribution 1, 2, 3
IIO Input offset current vs Free-air temperature 4
IIB
Input bias current
vs Common-mode input voltage
5
IIB Input bias current
vs Common-mode input voltage
vs Free-air temperature
5
6
vs Supply voltage
7
VOM+
Maximum positive peak output voltage
vs Supply voltage
vs Free-air temperature
7
8
VOM+ Maximum positive peak output voltage
vs Free-air temperature
vs Output current
vs Settling time
8
9
11
vs Output current
vs Settling time
9
11
vs Supply voltage
7
VOM−
Maximum negative peak output voltage
vs Supply voltage
vs Free-air temperature
7
8
VOM− Maximum negative peak output voltage
vs Free-air temperature
vs Output current
vs Settling time
8
10
11
vs Output current
vs Settling time
10
11
VO(PP) Maximum peak-to-peak output voltage vs Frequency 12
VOH High-level output voltage vs Output current 13
VOL Low-level output voltage vs Output current 14
AVD
Large-signal differential voltage amplification
vs Frequency
15
AVD Large-signal dif ferential voltage amplification
vs Frequency
vs Free-air temperature
15
16
zoClosed-loop output impedance vs Frequency 17
IOS Short-circuit output current vs Free-air temperature 18
CMRR
Common-mode rejection ratio
vs Frequency
19
CMRR Common-mode rejection ratio
vs Frequency
vs Free-air temperature
19
20
kSVR
Supply-voltage rejection ratio
vs Frequency
21
kSVR Supply-voltage rejection ratio
vs Frequency
vs Free-air temperature
21
22
ICC
Supply current
vs Supply voltage
23
ICC Supply current
vs Supply voltage
vs Free-air temperature
23
24
VnEquivalent input noise voltage vs Frequency 25
VnInput noise voltage Over a 10-second period 26
InNoise current vs Frequency 27
THD + N Total harmonic distortion plus noise vs Frequency 28
SR
Slew rate
vs Free-air temperature
29
SR
Slew rate
vs Free-air temperature
vs Load capacitance
29
30
Noninverting large signal vs Time 31
Pulse response Inverting large signal vs Time 32
Pulse response
Small signal vs Time 33
B1Unity-gain bandwidth vs Load capacitance 34
Gain margin vs Load capacitance 35
φmPhase margin vs Load capacitance 36
Phase shift vs Frequency 15
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
46 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 1
−400
12
8
4
00
Percentage of Units − %
16
20
24
400 800
TLE2141
DISTRIBUTION OF
INPUT OFFSET VOLTAGE
VIO − Input Offset Voltage − µV
236 Units Tested From 1 Wafer Lot
VCC± = ±15 V
TA = 25°C
P Package
−800
Figure 2
−400
12
8
4
00
Percentage of Units − %
16
20
24
400 800
TLE2142
DISTRIBUTION OF
INPUT OFFSET VOLTAGE
VIO − Input Offset Voltage − µV
236 Units Tested From 1 Wafer Lot
VCC± = ±15 V
TA = 25°C
P Package
−800 −200 200 600
−600
Figure 3
12
8
4
0−1.6 0
Percentage of Units − %
16
20
24
0.8 1.6
TLE2144
DISTRIBUTION OF
INPUT OFFSET VOLTAGE
VIO − Input Offset Voltage − mV
VCC± = ±15 V
TA = 25°C
N Package
250 Units Tested From 1 Wafer Lot
−0.8
− 2 −1.2 −0.4 0.4 1.2 2
Figure 4
10
8
4
2
0
18
6
IIO − Input Offset Current − nA
14
12
16
20
IIO
INPUT OFFSET CURRENT†
vs
FREE-AIR TEMPERATURE
−75 −50 −25 0 25 50 75 100 125
TA − Free-Air Temperature − °C150
VCC± = ±15 V
VCC± = ±2.5 V
VO = 0
VIC = 0
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
47
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 5
−2−2.5
−0.2
−1
−1.2
−1.4 −1.5 −1
IIB − Input Bias Current − uA
0
0 0.5 1
INPUT BIAS CURRENT†
vs
COMMON-MODE INPUT VOLTAGE
µAIIB
VIC − Common-Mode Input Voltage − V
VCC± = ±2.5 V
TA = 25°C
TA = 125°C
TA = −55°C
−0.4
−0.6
−0.8
−3 −0.5
Figure 6
IIB − Input Bias Current − nA
−1000
IIB
INPUT BIAS CURRENT†
vs
FREE-AIR TEMPERATURE
TA − Free-Air Temperature − °C
−75 −50 −25 0 25 50 75 100 125 150
VO = 0
VIC = 0
VCC± = ±15 V
−900
−800
−700
−600
−500
VCC± = ±2.5 V
Figure 7
0
−12
−18
− 24 0 3 6 9 12 15
− Maximum Peak Output Voltage − V
12
18
24
18 21 24
6
− 6
VOM
VCC± − Supply Voltage − V
MAXIMUM PEAK OUTPUT VOLTAGE
vs
SUPPLY VOLTAGE
RL = 2 kΩ
TA = 25°C
VOM+
VOM−
Figure 8
−14.2
−14.6
−15
14.6
−13.8
13.8
14.2
15
MAXIMUM PEAK OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
−75 −50 −25 0 25 50 75 100 125
TA − Free-Air Temperature − °C150
VCC± = ±15 V
VOM+
RL = 2 kΩ
RL = 2 kΩ
VOM−
RL = ∞
RL = ∞
− Maximum Peak Output Voltage − V
VOM
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
48 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 9
−4−0.4 −1
13.8
13.6
− Maximum Positive Peak Output Voltage − V
MAXIMUM POSITIVE PEAK
OUTPUT VOLTAGE†
vs
OUTPUT CURRENT
14
−10 −100− 40
14.4
14.2
14.6
IO − Output Current − mA
VOM +
VCC± = ±15 V
TA = 125°C
TA = 25°C
−0.1
TA = −55°C
Figure 10
−14.8
− 15
0.1 10.4
MAXIMUM NEGATIVE PEAK
OUTPUT VOLTAGE†
vs
OUTPUT CURRENT
−14.6
104 10040
−14.2
−14.4
−14
IO − Output Current − mA
−13.6
−13.8
−13.4 VCC± = ±15 V
TA = 125°C
TA = −55°C
TA = 25°C
− Maximum Negative Peak Output Voltage − V
VOM −
Figure 11
VOM − Maximum Peak Output Voltage − V
0
−7.5
−10
−12.5
10
0 100 200 300 400 500
5
2.5
7.5
12.5
ts − Settling Time − ns
VOM
MAXIMUM PEAK OUTPUT VOLTAGE
vs
SETTLING TIME
AVD = −1
VCC± = ±15 V
TA = 25°C
Rising
Falling
0.1%
0.01%
0.01%
0.1%
−2.5
−5
Figure 12
− Maximum Peak-to-Peak Output Voltage − V
MAXIMUM PEAK-TO-PEAK
OUTPUT VOLTAGE†
vs
FREQUENCY
5
0
25
100 k 400 k 1 M
f − Frequency − Hz
20
15
10
30
4 M 10 M
VCC± = ±15 V
RL = 2 kΩ
TA = 125°C
TA = −55°C
TA = 25°C
VO(PP)
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
49
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 13
3.6
3.4
4.6
−1 −10
− High-Level Output Voltage − V
4.4
4.2
4
HIGH-LEVEL OUTPUT VOLTAGE†
vs
OUTPUT CURRENT
VOH
IO − Output Current − mA −100
TA = −55°C
TA = 125°C
TA = 25°C
VCC = 5 V
3.8
−0.1
Figure 14
200
0
1000
0.1 1 10
VOL − Low-Level Output Voltage − mV
800
600
400
LOW-LEVEL OUTPUT VOLTAGE †
vs
OUTPUT CURRENT
VOL
IO − Output Current − mA 100
1400
1200
TA = −55°C
TA = 125°C
VCC = 5 V
TA = 25°C
10
20
1 10 100 1 M
30
40
50
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION AND PHASE SHIFT
vs
FREQUENCY
f − Frequency − Hz 10 M
− 10
0
Phase Shift
80
90
100
110
120
60
70
0°
20°
40°
60°
80°
100°
120°
140°
160°
180°
200°
220°
240°
260°
1 k 10 k 100 k
VCC± = ±15 V
RL = 2 kΩ
CL = 100 pF
TA = 25°C
AVD
Phase Shift
AVD − Large-Signal Differential
Voltage Amplification − dB
AVD
Figure 15
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
50 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 16
−75 −50 −25 0 25 50 75 100 125 150
LARGE-SIGNAL DIFFERENTIAL
VOLTAGE AMPLIFICATION†
vs
FREE-AIR TEMPERATURE
80
100
120
140
TA − Free-Air Temperature − °C
RL = 2 kΩ
RL = 10 kΩ
VCC± = ±15 V
VO = ±10 V
AVD − Large-Signal Differential
Voltage Amplification − dB
AVD
Figure 17
1
0.1
0.01
0.0011 k 10 k 100 k 1 M
− Closed-Loop Output Impedance −
10
f − Frequency − Hz
100
10 M
CLOSED-LOOP OUTPUT IMPEDANCE
vs
FREQUENCY
Ωzo
AVD = 100
AVD = 1
30 Ω
AVD = 10
Figure 18
− Short-Circuit Output Current − mA
−75 −50 −25 0 25 50 75 100 125 150
20
30
40
TA − Free-Air Temperature − °C
SHORT-CIRCUIT OUTPUT CURRENT†
vs
FREE-AIR TEMPERATURE
50
60
OS
I
VCC± = ±15 V
VO = 0
VID = 1
VID = −1
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
51
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 19
f − Frequency − Hz
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
60
40
20
0
100 1 k 10 k
CMRR − Common-Mode Rejection Ratio − dB
80
100
120
100 k 1 M
140 VCC± = ±15 V
TA = 25°C
Figure 20
−75 −50 −25 0 25 50 75 100 125 150
100
104
108
112
TA − Free-Air Temperature − °C
COMMON-MODE REJECTION RATIO†
vs
FREE-AIR TEMPERATURE
116
120
CMRR − Common-Mode Rejection Ratio − dB
VCC = 5 V
VIC = VICRmin
VCC± = ±15 V
Figure 21
100
80
20
010 100 1 k
kSVR − Supply-Voltage Rejection Ratio − dB
120
140
f − Frequency − Hz
160
10 k 100 k 1 M 10 M
SUPPLY-VOLTAGE REJECTION RATIO
vs
FREQUENCY
kSVR
kSVR−
VCC± = ±2.5 V to ±15 V
TA = 25°C
60
40
kSVR+
Figure 22
SUPPLY-VOLTAGE REJECTION RATIO †
vs
FREE-AIR TEMPERATURE
TA − Free-Air Temperature − °C
106
104
102
100
108
110
−75 −50 −25 0 25 50 75 100 125 150
VCC± = ±2.5 V to ±15 V
kSVR − Supply-Voltage Rejection Ratio − dB
kSVR
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
52 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 23
SUPPLY CURRENT†
vs
SUPPLY VOLTAGE
IDD − Supply Current − mA
CC
I
2.5
2048121620
3
3.5
24
|VCC±| − Supply Voltage − V
4
TA = 125°C
TA = −55°C
TA = 25°C
VO = 0
No Load
Figure 24
2.8
3
3.2
3.4
3.6
3.8
IDD − Supply Current − mA
CC
I
SUPPLY CURRENT†
vs
FREE-AIR TEMPERATURE
−75 −50 −25 0 25 50 75 100 125 150
TA − Free-Air Temperature − °C
VO = 0
No Load
VCC± = ±15 V
VCC± = ±2.5 V
Figure 25
250
Vn − Equivalent Input Noise Voltage −
100
50
01 100 1 k
150
f − Frequency − Hz
200
10 k
EQUIVALENT INPUT NOISE VOLTAGE†
vs
FREQUENCY
TA = 125°C
TA = −55°C
TA = 25°C
VCC± = ±15 V
RS = 20Ω
10
nV/ Hz
Figure 26
246
0
250
810
t − Time − s
INPUT NOISE VOLTAGE
OVER A 10-SECOND PERIOD
500
750 VCC± = ±15 V
f = 0.1 to 10 Hz
TA = 25°C
Input Noise Voltage − nV
−250
−500
−7500
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
53
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 27
4
2
0
6
8
10 100 1 k 10 k
− Noise Current − pA/
In
f − Frequency − Hz
NOISE CURRENT†
vs
FREQUENCY
Hz
TA = −55°C
TA = 25°C
TA = 125°C
1
Figure 28
0.001%10 1 k 10 k 100
k
THD + N − Total Harmonic Distortion + Noise − %
TOTAL HARMONIC DISTORTION
PLUS NOISE
vs
FREQUENCY
0.01%
0.1%
1%
100 f − Frequency − Hz
VO(PP) = 20 V
VCC± = ±15 V
TA = 25°CAV = 100
RL = 600 Ω
AV = 100
RL = 2 kΩ
AV = 10
RL = 2 kΩ
AV = 10
RL = 600 Ω
Figure 29
−75 −50 −25 0 25 50 75 100 125 150
TA − Free-Air Temperature − °C
30
20
10
40
µs
SR − Slew Rate − V/
SLEW RATE†
vs
FREE-AIR TEMPERATURE
0
50
60
SR +
SR −
VCC± = ±15 V
AVD = − 1
RL = 2 kΩ
CL = 500 pF
Figure 30
µs
SR − Slew Rate − V/
0
10
20
30
CL − Load Capacitance − nF
SLEW RATE
vs
LOAD CAPACITANCE
101 0.10.01
VCC± = ±15 V
AVD = − 1
TA = 25°C
SR+
SR−
40
50
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
54 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 31
0
−10
−15 01
5
10
15
2345
VO − Output Voltage − V
VO
t − Time − µs
NONINVERTING
LARGE-SIGNAL
PULSE RESPONSE†
TA = −55°C
TA = 25°C
TA = 125°C
TA = 25°C
TA = −55°C
TA = 125°C
VCC± = ±15 V
AVD = 1
RL = 2 kΩ
CL = 300 pF
0
−10
−15
5
10
15
−5
Figure 32
543210
t − Time − µs
INVERTING
LARGE-SIGNAL
PULSE RESPONSE†
VO − Output Voltage − V
VO
VCC± = ±15 V
AVD = −1
RL = 2 kΩ
CL = 300 pF
TA = 25°C
TA = −55°C
TA = 125°CTA = −55°C
TA = 25°C
TA = 125°C
0
−10
−15
5
10
15
−5
Figure 33
VO − Output Voltage − mV
V
O
0
−100
100
50
4000 800 1200 1600
t − Time − ns
SMALL-SIGNAL
PULSE RESPONSE
VCC± = ±15 V
AVD = −1
RL = 2 kΩ
CL = 300 pF
TA = 25°C
−50
Figure 34
4
3
2
110 100
B1 − Unity-Gain Bandwidth − MHz
5
6
7
1000 10000
B1
CL − Load Capacitance − pF
UNITY-GAIN BANDWIDTH†
vs
LOAD CAPACITANCE
TA = −55°C
TA = 25°C
TA = 125°C
VCC± = ±15 V
RL = 2 kΩ
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
55
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TYPICAL CHARACTERISTICS
Figure 35
2
010
Gain Margin − dB
4
6
10000
CL − Load Capacitance − pF
8
10
GAIN MARGIN†
vs
LOAD CAPACITANCE
1000100
12
14
TA = 125°C
TA = 25°C
TA = −55°C
VCC± = ±15 V
AVD = 1
RL = 2 kΩ to ∞
VO = −10 V to 10 V
Figure 36
10 10000
CL − Load Capacitance − pF
PHASE MARGIN†
vs
LOAD CAPACITANCE
1000100
− Phase Margin
TA = −55°C
TA = 125°C
VCC± = ±15 V
RL = 2 kΩ
70°
60°
50°
40°
30°
20°
10°
0°
φm
TA = 25°C
†Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices.
SLOS183C − FEBRUAR Y 1997 − REVISED JUNE 2006
56 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
APPLICATION INFORMATION
input offset voltage nulling
The TLE2141 series offers external null pins that can be used to further reduce the input offset voltage. If this
feature is desired, connect the circuit of Figure 37 as shown. If external nulling is not needed, the null pins may
be left unconnected.
+
−OUT
IN+
IN−
3
26
15 OFFSET N1
OFFSET N2 5 kΩ
1 kΩVCC− (split supply)
GND (single supply)
Figure 37. Input Offset Voltage Null Circuit
PACKAGE OPTION ADDENDUM
www.ti.com 27-Apr-2012
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
5962-9321603Q2A ACTIVE LCCC FK 20 1 TBD Call TI Call TI
5962-9321603QHA ACTIVE CFP U 10 1 TBD Call TI Call TI
5962-9321603QPA ACTIVE CDIP JG 8 1 TBD Call TI Call TI
5962-9321604Q2A ACTIVE LCCC FK 20 1 TBD Call TI Call TI
5962-9321604QHA ACTIVE CFP U 10 1 TBD Call TI Call TI
5962-9321604QPA ACTIVE CDIP JG 8 1 TBD Call TI Call TI
5962-9321605Q2A ACTIVE LCCC FK 20 1 TBD Call TI Call TI
5962-9321605QCA ACTIVE CDIP J 14 1 TBD Call TI Call TI
5962-9321606Q2A ACTIVE LCCC FK 20 1 TBD Call TI Call TI
5962-9321606QCA ACTIVE CDIP J 14 1 TBD Call TI Call TI
TLE2141ACD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141ACDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141ACP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2141ACPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2141AID ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141AIDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141AIDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141AIP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2141AIPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2141CD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141CDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141CDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com 27-Apr-2012
Addendum-Page 2
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TLE2141CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141CP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2141CPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2141ID ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141IDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141IDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141IP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2141IPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2141MD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2141MDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142ACD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142ACDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142ACDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142ACDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142ACP OBSOLETE PDIP P 8 TBD Call TI Call TI
TLE2142AID ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142AIDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142AIDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142AIDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com 27-Apr-2012
Addendum-Page 3
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TLE2142AIP OBSOLETE PDIP P 8 TBD Call TI Call TI
TLE2142AMD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142AMDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142AMDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142AMDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type
TLE2142AMJG ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type
TLE2142AMJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type
TLE2142AMUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type
TLE2142CD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142CDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142CDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142CDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142CP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2142CPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2142CPWLE OBSOLETE TSSOP PW 16 TBD Call TI Call TI
TLE2142CPWR ACTIVE TSSOP PW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142CPWRG4 ACTIVE TSSOP PW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142ID ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142IDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142IDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com 27-Apr-2012
Addendum-Page 4
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TLE2142IDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142IP ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2142IPE4 ACTIVE PDIP P 8 50 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2142MD ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142MDG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142MDR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142MDRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2142MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type
TLE2142MJGB ACTIVE CDIP JG 8 1 TBD A42 N / A for Pkg Type
TLE2142MUB ACTIVE CFP U 10 1 TBD A42 N / A for Pkg Type
TLE2144ACN ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2144ACNE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2144AIN ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2144AINE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2144AMFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type
TLE2144AMJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type
TLE2144CDW ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2144CDWG4 ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2144CDWR ACTIVE SOIC DW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2144CDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2144CN ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2144CNE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2144IDW ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
PACKAGE OPTION ADDENDUM
www.ti.com 27-Apr-2012
Addendum-Page 5
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TLE2144IDWG4 ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2144IDWR ACTIVE SOIC DW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2144IDWRG4 ACTIVE SOIC DW 16 2000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2144IN ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2144INE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type
TLE2144MDW ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2144MDWG4 ACTIVE SOIC DW 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM
TLE2144MFKB ACTIVE LCCC FK 20 1 TBD POST-PLATE N / A for Pkg Type
TLE2144MJB ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type
TLE2144MN OBSOLETE PDIP N 14 TBD Call TI Call TI
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
PACKAGE OPTION ADDENDUM
www.ti.com 27-Apr-2012
Addendum-Page 6
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLE2141, TLE2141A, TLE2142, TLE2142A, TLE2142AM, TLE2142M, TLE2144, TLE2144A, TLE2144AM, TLE2144M :
•Catalog: TLE2142A, TLE2142, TLE2144A, TLE2144
•Automotive: TLE2141-Q1, TLE2142-Q1, TLE2142-Q1
•Enhanced Product: TLE2141-EP, TLE2144-EP, TLE2144-EP
•Military: TLE2141M, TLE2141AM, TLE2142M, TLE2142AM, TLE2144M, TLE2144AM
NOTE: Qualified Version Definitions:
•Catalog - TI's standard catalog product
•Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•Enhanced Product - Supports Defense, Aerospace and Medical Applications
•Military - QML certified for Military and Defense Applications
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
TLE2141AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2141AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2141CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2141IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2141MDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2142ACDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2142AIDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2142AMDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2142CDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2142CPWR TSSOP PW 16 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1
TLE2142IDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2142MDR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TLE2144CDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1
TLE2144IDWR SOIC DW 16 2000 330.0 16.4 10.75 10.7 2.7 12.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TLE2141AIDR SOIC D 8 2500 367.0 367.0 35.0
TLE2141AIDR SOIC D 8 2500 340.5 338.1 20.6
TLE2141CDR SOIC D 8 2500 340.5 338.1 20.6
TLE2141IDR SOIC D 8 2500 340.5 338.1 20.6
TLE2141MDR SOIC D 8 2500 367.0 367.0 35.0
TLE2142ACDR SOIC D 8 2500 340.5 338.1 20.6
TLE2142AIDR SOIC D 8 2500 340.5 338.1 20.6
TLE2142AMDR SOIC D 8 2500 367.0 367.0 35.0
TLE2142CDR SOIC D 8 2500 340.5 338.1 20.6
TLE2142CPWR TSSOP PW 16 2000 367.0 367.0 35.0
TLE2142IDR SOIC D 8 2500 340.5 338.1 20.6
TLE2142MDR SOIC D 8 2500 367.0 367.0 35.0
TLE2144CDWR SOIC DW 16 2000 367.0 367.0 38.0
TLE2144IDWR SOIC DW 16 2000 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
MECHANICAL DATA
MCER001A – JANUARY 1995 – REVISED JANUAR Y 1997
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE
0.310 (7,87)
0.290 (7,37)
0.014 (0,36)
0.008 (0,20)
Seating Plane
4040107/C 08/96
5
4
0.065 (1,65)
0.045 (1,14)
8
1
0.020 (0,51) MIN
0.400 (10,16)
0.355 (9,00)
0.015 (0,38)
0.023 (0,58)
0.063 (1,60)
0.015 (0,38)
0.200 (5,08) MAX
0.130 (3,30) MIN
0.245 (6,22)
0.280 (7,11)
0.100 (2,54)
0°–15°
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. This package can be hermetically sealed with a ceramic lid using glass frit.
D. Index point is provided on cap for terminal identification.
E. Falls within MIL STD 1835 GDIP1-T8
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
