LM3916 LM3916 Dot/Bar Display Driver Literature Number: SNVS762A LM3916 Dot/Bar Display Driver General Description The LM3916 is a monolithic integrated circuit that senses analog voltage levels and drives ten LEDs, LCDs or vacuum fluorescent displays, providing an electronic version of the popular VU meter. One pin changes the display from a bar graph to a moving dot display. LED current drive is regulated and programmable, eliminating the need for current limiting resistors. The whole display system can operate from a single supply as low as 3V or as high as 25V. The IC contains an adjustable voltage reference and an accurate ten-step voltage divider. The high-impedance input buffer accepts signals down to ground and up to within 1.5V of the positive supply. Further, it needs no protection against inputs of 35V. The input buffer drives 10 individual comparators referenced to the precision divider. Accuracy is typically better than 0.2 dB. Audio applications include average or peak level indicators, and power meters. Replacing conventional meters with an LED bar graph results in a faster responding, more rugged display with high visibility that retains the ease of interpretation of an analog display. The LM3916 is extremely easy to apply. A 1.2V full-scale meter requires only one resistor in addition to the ten LEDs. One more resistor programs the full-scale anywhere from 1.2V to 12V independent of supply voltage. LED brightness is easily controlled with a single pot. (c) 2004 National Semiconductor Corporation DS007971 The LM3916 is very versatile. The outputs can drive LCDs, vacuum fluorescents and incandescent bulbs as well as LEDs of any color. Multiple devices can be cascaded for a dot or bar mode display for increased range and/or resolution. Useful in other applications are the linear LM3914 and the logarithmic LM3915. Features Fast responding electronic VU meter Drivers LEDs, LCDs, or vacuum fluorescents Bar or dot display mode externally selectable by user Expandable to displays of 70 dB Internal voltage reference from 1.2V to 12V Operates with single supply of 3V to 25V Inputs operate down to ground Output current programmable from 1 mA to 30 mA Input withstands 35V without damage or false outputs Outputs are current regulated, open collectors Directly drives TTL or CMOS The internal 10-step divider is floating and can be referenced to a wide range of voltages The LM3916 is rated for operation from 0C to +70C. The LM3916N-1 is available in an 18-lead molded DIP package. n n n n n n n n n n n n www.national.com LM3916 Dot/Bar Display Driver January 2000 LM3916 Typical Applications 0V to 10V VU Meter 00797101 Notes: Capacitor C1 is required if leads to the LED supply are 6" or longer. Circuit as shown is wired for dot mode. For bar mode, connect pin 9 to pin 3. VLED must be kept below 7V or dropping resistor should be used to limit IC power dissipation. www.national.com 2 (Note 1) Reference Load Current Voltage on Output Drivers 25V -55C to +150C Lead Temperature (Soldering, 10 seconds) 1365 mW 25V 10 mA Storage Temperature Range Power Dissipation (Note 6) Supply Voltage -100 mV to V+ Divider Voltage If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Molded DIP (N) 35V Input Signal Overvoltage (Note 4) 260C Electrical Characteristics (Notes 2, 4) Parameter Conditions (Note 2) Min Typ Max Units COMPARATORS Offset Voltage, Buffer and First Comparator 0V VRLO = VRHI 12V, ILED = 1 mA 3 10 mV Offset Voltage, Buffer and Any Other Comparator 0V VRLO = VRHI 12V, ILED = 1 mA 3 15 mV Gain (ILED/ VIN) I(REF) = 2 mA, ILED = 10 mA Input Bias Current (at Pin 5) 0V VIN (V+ -1.5V) Input Signal Overvoltage No Change in Display 3 8 25 -35 mA/mV 100 nA 35 V VOLTAGE DIVIDER Divider Resistance Total, Pin 6 to 4 8 12 17 k Relative Accuracy (Input Change Between Any Two Threshold Points) (Note 3) -1 dB VIN 3 dB -7 dB VIN -1 dB -10 dB VIN -7 dB 0.75 1.5 2.5 1.0 2.0 3.0 1.25 2.5 2.5 dB dB dB Absolute Accuracy (Note 3) VIN = 2, 1, 0, -1 dB VIN = -3, -5 dB VIN = -7, -10, -20 dB -0.25 -0.5 -1 +0.25 +0.5 +1 dB dB dB 1.28 1.34 V VOLTAGE REFERENCE Output Voltage 0.1 mA IL(REF) 4 mA, V+ = VLED = 5Vg Line Regulation 3V V+ 18V 0.01 0.03 %/V Load Regulation 0.1 mA IL(REF) 4 mA, V+ = VLED = 5V 0.4 2 % Output Voltage Change with Temperature 0C TA +70C, IL(REF) = 1 mA, V+ = VLED = 5V 1.2 1 Adjust Pin Current 75 % 120 A OUTPUT DRIVERS LED Current V+ = VLED = 5V, IL(REF) = 1 mA 10 13 mA LED Current Difference (Between Largest and Smallest LED Currents) VLED = 5V, ILED = 2 mA VLED = 5V, ILED = 20 mA 0.12 1.2 0.4 3 mA mA LED Current Regulation 2V VLED 17V ILED 2 mA ILED = 20 mA 0.1 1 0.25 3 mA mA 1.5 V Dropout Voltage 7 ILED(ON) = 20 mA @ VLED = 5V, ILED = 2 mA Saturation Voltage ILED = 2.0 mA, IL(REF) = 0.4 mA 0.15 0.4 V Output Leakage, Each Collector Bar Mode (Note 5) 0.1 100 A Output Leakage Dot Mode (Note 5) 0.1 100 A 150 450 A Pins 10-18 Pin 1 60 SUPPLY CURRENT 3 www.national.com LM3916 Absolute Maximum Ratings LM3916 Electrical Characteristics (Notes 2, 4) Parameter (Continued) Conditions (Note 2) Min Typ Max Units 2.4 6.1 4.2 9.2 mA mA V+ = + 5V, IL(REF) = 0.2 mA V+ = + 20V, IL(REF) = 1.0 mA Standby Supply Current (All Outputs Off) Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Note 2: Unless otherwise stated, all specifications apply with the following conditions: 3 VDC V+ 20 VDC -0.015V VRLO 12 VDC TA = 25C, IL(REF) = 0.2 mA, pin 9 connected to pin 3 (bar mode). VREF, VRHI, VRLO (V+ - 1.5V) 3 VDC VLED V+ 0V VIN V+ - 1.5V -0.015V VRHI 12 VDC For higher power dissipations, pulse testing is used. Note 3: Accuracy is measured referred to +3 dB = +10.000 VDC at pin 5, with +10.000 VDC at pin 6, and 0.000 VDC at pin 4. At lower full-scale voltages, buffer and comparator offset voltage may add significant error. See table for threshold voltages. Note 4: Pin 5 input current must be limited to 3 mA. The addition of a 39k resistor in series with pin 5 allows 100V signals without damage. Note 5: Bar mode results when pin 9 is within 20 mV of V+. Dot mode results when pin 9 is pulled at least 200 mV below V+. LED #10 (pin 10 output current) is disabled if pin 9 is pulled 0.9V or more below VLED. Note 6: The maximum junction temperature of the LM3916 is 100C. Devices must be derated for operation at elevated temperatures. Junction to ambient thermal resistance is 55C/W for the molded DIP (N package). LM3916 Threshold Voltage dB Volts Min Typ Max Volts dB Min Typ Max 12 3 9.985 10.000 10.015 -3 4.732 5.012 5.309 2 14 8.660 8.913 9.173 -5 12 3.548 3.981 4.467 1 14 7.718 7.943 8.175 -7 1 2.818 3.162 3.548 0 6.879 7.079 7.286 -10 1 1.995 2.239 2.512 -1 12 5.957 6.310 6.683 -20 1 0.631 0.708 0.794 14 www.national.com (Note 3) 4 LM3916 Typical Performance Characteristics Supply Current vs Temperature Operating Input Bias Current vs Temperature 00797136 00797135 Reference Voltage vs Temperature Reference Adjust Pin Current vs Temperature 00797138 00797137 LED Current-Regulation Dropout LED Driver Saturation Voltage 00797139 00797140 5 www.national.com LM3916 Typical Performance Characteristics (Continued) Input Current Beyond Signal Range (Pin 5) LED Current vs Referenced Loading 00797141 00797142 LED Driver Current Regulation Total Divider Resistance vs Temperature 00797143 00797144 Common-Mode Limits Output Characteristics 00797146 00797145 www.national.com 6 LM3916 Block Diagram (Showing Simplest Application) 00797104 7 www.national.com LM3916 lighted LED, and this current will be relatively constant despite supply voltage and temperature changes. Current drawn by the internal 10-resistor divider, as well as by the external current and voltage-setting divider should be included in calculating LED drive current. The ability to modulate LED brightness with time, or in proportion to input voltage and other signals can lead to a number of novel displays or ways of indicating input overvoltages, alarms, etc. The LM3916 outputs are current-limited NPN transistors as shown below. An internal feedback loop regulates the transistor drive. Output current is held at about 10 times the reference load current, independent of output voltage and processing variables, as long as the transistor is not saturated. Functional Description The simplified LM3916 block diagram is included to give the general idea of the circuit's operation. A high input impedance buffer operates with signals from ground to 12V, and is protected against reverse and overvoltage signals. The signal is then applied to a series of 10 comparators; each of which is biased to a different comparison level by the resistor string. In the example illustrated, the resistor string is connected to the internal 1.25V reference voltage. As the input voltage varies from 0 to 1.25, the comparator outputs are driven low one by one, switching on the LED indicators. The resistor divider can be connected between any 2 voltages, providing that they are at least 1.5V below V+ and no lower than V-. LM3916 Output Circuit INTERNAL VOLTAGE REFERENCE The reference is designed to be adjustable and develops a nominal 1.25V between the REF OUT (pin 7) and REF ADJ (pin 8) terminals. The reference voltage is impressed across program resistor R1 and, since the voltage is constant, a constant current I1 then flows through the output set resistor R2 giving an output voltage of: 00797106 Outputs may be run in saturation with no adverse effects, making it possible to directly drive logic. The effective saturation resistance of the output transistors, equal to RE plus the transistors' collector resistance, is about 50. It's also possible to drive LEDs from rectified AC with no filtering. To avoid oscillations, the LED supply should be bypassed with a 2.2 F tantalum or 10 F aluminum electrolytic capacitor. MODE PIN USE Pin 9, the Mode Select input, permits chaining of multiple devices, and controls bar or dot mode operation. The following tabulation shows the basic ways of using this input. Other more complex uses will be illustrated in the applications. Bar Graph Display: Wire Mode Select (pin 9) directly to pin 3 (V+ pin). Dot Display, Single LM3916 Driver: Leave the Mode Select pin open circuit. Dot Display, 20 or More LEDs: Connect pin 9 of the first drivers in the series (i.e., the one with the lowest input voltage comparison points) to pin 1 of the next higher LM3916 driver. Continue connecting pin 9 of lower input drivers to pin 1 of higher input drivers for 30 or more LED displays. The last LM3916 driver in the chain will have pin 9 left open. All previous drivers should have a 20k resistor in parallel with LED #9 (pin 11 to VLED). 00797105 Since the 120 A current (max) from the adjust terminal represents an error term, the reference was designed to minimize changes of this current with V+ and load changes. For correct operation, reference load current should be between 80 A and 5 mA. Load capacitance should be less than 0.05 F. CURRENT PROGRAMMING A feature not completely illustrated by the block diagram is the LED brightness control. The current drawn out of the reference voltage pin (pin 7) determines LED current. Approximately 10 times this current will be drawn through each www.national.com 8 In order for display to make sense when multiple drivers are cascaded in dot mode, special circuitry has been included to shut off LED #10 of the first device when LED #1 of the second device comes on. The connection for cascading in dot mode has already been described and is depicted in Figure 1. As long as the input signal voltage is below the threshold of the second driver, LED #11 is off. Pin 9 of driver #1 thus sees effectively an open circuit so the chip is in dot mode. As soon as the input voltage reaches the threshold of LED #11, pin 9 of driver #1 is pulled an LED drop (1.5V or more) below VLED. This condition is sensed by comparator C2, referenced 600 mV below VLED. This forces the output of C2 low, which shuts off output transistor Q2, extinguishing LED #10. VLED is sensed via the 20k resistor connected to pin 11. The very small current (less than 100 A) that is diverted from LED #9 does not noticeably affect its intensity. This pin actually performs two functions. Refer to the simplified block diagram below. Block Diagram of Mode Pin Function An auxiliary current source at pin 1 keeps at least 100 A flowing through LED #11 even if the input voltage rises high enough to extinguish the LED. This ensures that pin 9 of driver #1 is held low enough to force LED #10 off when any higher LED is illuminated. While 100 A does not normally produce significant LED illumination, it may be noticeable when using high-efficiency LEDs in a dark environment. If this is bothersome, the simple cure is to shunt LED #11 (and LED #1) with a 10k resistor. The 1V 1R drop is more than the 900 mV worst case required to hold off LED #10 yet small enough that LED #11 does not conduct significantly. 00797107 *High for bar DOT OR BAR MODE SELECTION The voltage at pin 9 is sensed by comparator C1, nominally referenced to (V+ -100 mV). The chip is in bar mode when pin 9 is above this level; otherwise it's in dot mode. The comparator is designed so that pin 9 can be left open circuit for dot mode. Taking into account comparator gain and variation in the 100 mV reference level, pin 9 should be no more than 20 mV below V+ for bar mode and more than 200 mV below V+ (or open circuit) for dot mode. In most applications, pin 9 is either open (dot mode) or tied to V+ (bar mode). In bar mode, pin 9 should be connected directly to pin 3. Large currents drawn from the power supply (LED current, for example) should not share this path so that large IR drops are avoided. In some circuits a number of outputs on the higher device are not used. Examples include the high resolution VU meter and the expanded range VU meter circuits (see Typical Applications). To provide the proper carry sense voltage in dot mode, the LEDs of the higher driver IC are tied to VLED through two series-connected diodes as shown in Figure 2. Shunting the diodes with a 1k resistor provides a path for driver leakage current. 00797108 FIGURE 1. Cascading LM3914/15/16 Series in Dot Mode 9 www.national.com LM3916 DOT MODE CARRY Mode Pin Functional Description LM3916 Mode Pin Functional Description (Continued) 00797109 FIGURE 2. Cascading Drivers in Dot Mode with Pin 1 of Driver #2 Unused Power dissipation, especially in bar mode should be given consideration. For example, with a 5V supply and all LEDs programmed to 20 mA the driver will dissipate over 600 mW. In this case a 7.5 resistor in series with the LED supply will cut device heating in half. The negative end of the resistor should be bypassed with a 2.2 F solid tantalum or 10 F aluminum electrolytic capacitor to pin 2. OTHER DEVICE CHARACTERISTICS The LM3915 is relatively low-powered itself, and since any number of LEDs can be powered from about 3V, it is a very efficient display driver. Typical standby supply current (all LEDs OFF) is 1.6 mA. However, any reference loading adds 4 times that current drain to the V+ (pin 3) supply input. For example, an LM3915 with a 1 mA reference pin load (1.3k) would supply almost 10 mA to every LED while drawing only 10 mA from its V+ pin supply. At full-scale, the IC is typically drawing less than 10% of the current supplied to the display. The display driver does not have built-in hysteresis so that the display does not jump instantly from one LED to the next. Under rapidly changing signal conditions, this cuts down high frequency noise and often an annoying flicker. An "overlap" is built in so that at no time are all segments completely off the dot mode. Generally one LED fades in while the other fades out over a 1 mV range. The change may be much more rapid between LED #10 of one device and LED #1 of a second device cascaded. TIPS ON RECTIFIER CIRCUITS The simplest way to display an AC signal using the LM3916 is to apply it right to pin 5 unrectified. Since the LED illuminated represents the instantaneous value of the AC waveform, one can readily discern both peak and average values of audio signals in this manner. The LM3916 will respond to positive half-cycles only but will not be damaged by signals up to 35V (or up to 100V if a 39k resistor is in series with the input). A smear or bar type display results even though the LM3916 is connected for dot mode. The LEDs should be run at 20 mA to 30 mA for high enough average intensity. True average or peak detection requires rectification. If an LM3916 is set up with 10V full scale across its voltage divider, the turn-on point for the first LED is only 450 mV. A simple silicon diode rectifier won't work well at the low end due to the 600 mV diode threshold. The half-wave peak detector in Figure 3 uses a PNP emitter-follower in front of the diode. Now, the transistor's base-emitter voltage cancels out the diode offset, within about 100 mV. This approach is usually satisfactory when a single LM3916 is used for a 23 dB display. Display circuits such as the extended range VU meter using two or more drivers for a dynamic range of 40 dB or greater require more accurate detection. In the precision half-wave rectifier of Figure 4 the effective diode offset is reduced by a factor equal to the open-loop gain of the op amp. Filter capacitor C2 charges through R3 and discharges through R2 and R3, so that appropriate selection of these values results in either a peak or an average detector. The circuit has a gain equal to R2/R1. It's best to capacitively couple the input. Audio sources frequently have a small DC offset that can cause significant error at the low end of the log display. Op amps that slew quickly, such as the LF351, LF353 or LF356, are needed to faithfully respond to sudden transients. It may be necessary to trim out the op amp DC offset voltage to accurately cover a 60 dB range. Best results are obtained if the circuit is Application Hints The most difficult problem occurs when large LED currents are being drawn, especially in bar graph mode. These currents flowing out of the ground pin cause voltage drops in external wiring, and thus errors and oscillations. Bringing the return wires from signal sources, reference ground and bottom of the resistor string to a single point very near pin 2 is the best solution. Long wires from VLED to LED anode common can cause oscillations. The usual cure is bypassing the LED anodes with a 2.2 F tantalum or 10 F aluminum electrolytic capacitor. If the LED anode line wiring is inaccessible, often a 0.1 F capacitor from pin 1 to pin 2 will be sufficient. If there is a large amount of LED overlap in the bar mode, oscillation or excessive noise is usually the problem. In cases where proper wiring and bypassing fail to stop oscillations, V+ voltage at pin 3 is usually below suggested limits. When several LEDs are lit in dot mode, the problem is usually an AC component of the input signal which should be filtered out. Expanded scale meter applications may have one or both ends of the internal voltage divider terminated at relatively high value resistors. These high-impedance ends should be bypassed to pin 2 with 0.1 F. www.national.com 10 LM3916 Application Hints (Continued) adjusted for the correct output when a low-level AC signal (10 to 20 mV) is applied, rather than adjusting for zero output with zero input. 00797110 *DC Couple 00797112 D1, D2: 1N914 or 1N4148 FIGURE 3. Half-Wave Peak Detector FIGURE 5. Precision Full-Wave Average Detector 00797111 D1, D2: 1N914 or 1N4148 Average Peak R2 1k 100k R3 100k 1k 00797113 R1 = R2 for AV = 1 R1 = R2/10 for AV = 10 C1 = 10/R1 D1, D2, D3, D4: 1N914 OR 1N4148 Attack and decay time to DIN PPM spec. Response down 1 dB for 10 ms tone burst. Decays 20 dB in 1.5s. FIGURE 4. Precision Half-Wave Rectifier FIGURE 6. Precision Full-Wave Peak Detector For precision full-wave averaging use the circuit in Figure 5. Using 1% resistors for R1 through R4, gain for positive and negative signal differs by only 0.5 dB worst case. Substituting 5% resistors increases this to 2 dB worst case. (A 2 dB gain difference means that the display may have a 1 dB error when the input is a nonsymmetrical transient). The averaging time constant is R5 * C2. A simple modification results in the precision full-wave detector of Figure 6. Since the filter capacitor is not buffered, this circuit can drive only high impedance loads such as the input of an LM3916. AUDIO METER STANDARDS VU Meter The audio level meter most frequently encountered is the VU meter. Its characteristics are defined as the ANSI specification C165. The LM3916's outputs correspond to the meter indications specified with the omission of the -2 VU indication. The VU scale divisions differ slightly from a linear scale in order to obtain whole numbers in dB. Some of the most important specifications for an AC meter are its dynamic characteristics. These define how the meter responds to transients and how fast the reading decays. The VU meter is a relatively slow full-wave averaging type, specified to reach 99% deflection in 300 ms and overshoot by 1 to 1.5%. In engineering terms this means a slightly under- 11 www.national.com LM3916 Application Hints of 2.1 Hz and a Q of 0.62. Figure 7 depicts a simple rectifier/ filter circuit that meets these criteria. (Continued) damped second order response with a resonant frequency 00797114 Design Equations GAIN R5 R6 C2 C3 1 100k 43k 2.0 0.56 F 10 1M 100k 1.0 0.056 F FIGURE 7. Full-Wave Average Detector to VU Meter Specifications* Peak Program Meter The VU meter, originally intended for signals sent via telephone lines, has shortcomings when used in high fidelity systems. Due to its slow response time, a VU meter will not accurately display transients that can saturate a magnetic tape or drive an amplifier into clipping. The fast-attack peak program meter (PPM) which does not have this problem is becoming increasingly popular. While several European organizations have specifications for peak program meters, the German DIN specification 45406 is becoming a de facto standard. Rather than respond instantaneously to peak, however, PPM specifications require a finite "integration time" so that only peaks wide enough to be audible are displayed. DIN 45406 calls for a response of 1 dB down from steady-state for a 10 ms tone burst and 4 dB down for a 3 ms tone burst. These requirements are consistent with the other frequently encountered spec of 2 dB down for a 5 ms burst and are met by an attack time constant of 1.7 ms. www.national.com The specified return time of 1.5s to -20 dB requires a 650 ms decay time constant. The full-wave peak detector of Figure 6 satisfies both the attack and decay time criteria. Cascading The LM3916 The LM3916 by itself covers the 23 dB range of the conventional VU meter. To display signals of 40 dB or 70 dB dynamic range, the LM3916 may be cascaded with the 3 dB/step LM3915s. Alternatively, two LM3916s may be cascaded for increased resolution over a 28 dB range. Refer to the Extended Range VU Meter and High Resolution VU Meter in the Typical Applications section for the complete circuits for both dot and bar mode displays. To obtain a display that makes sense when an LM3915 and an LM3916 are cascaded, the -20 dB output from the LM3916 is dropped. The full-scale display for the LM3915 is set at 3 dB below the LM3916's -10 dB output and the rest of the thresholds continue the 3 dB/step spacing. A simple, low cost approach is to set the reference voltage of the two chips 16 dB apart as in Figure 5. The LM3915, with pin 8 grounded, runs at 1.25V full-scale. R1 and R2 set the 12 comparator offset voltage may be as high as 10 mV, large errors can occur at the first few thresholds. A better approach, as shown in Figure 9, is to keep the reference the same for both drivers (10V in the example) and amplify the input signal by 16 dB ahead of the LM3915. Alternatively, instead of amplifying, input signals of sufficient amplitude can be fed directly to the LM3916 and attenuated by 16 dB to drive the LM3915. (Continued) LM3916's reference 16 dB higher or 7.89V. Variation in the two on-chip references and resistor tolerance may cause a 1 dB error in the -10 dB to -13 dB transition. If this is objectionable, R2 can be trimmed. The drawback of the aforementioned approach is that the threshold of LED #1 on the LM3915 is only 56 mV. Since 00797115 VREF2 . 7.89V FIGURE 8. Low Cost Circuit for 40 dB Display 00797116 FIGURE 9. Improved Circuit for 40 dB Display 13 www.national.com LM3916 Application Hints LM3916 Application Hints (Continued) To extend this approach to get a 70 dB display, another 30 dB of amplification must be placed in the signal path ahead of the lowest LM3915. Extreme care is required as the lowest LM3915 displays input signals down to 2 mV! Several offset nulls may be required. High currents should not share the same path as the low level signal. Also power line wiring should be kept away from signal lines. TIPS ON REFERENCE VOLTAGE AND LED CURRENT PROGRAMMING Single Driver The equations in Figure 10 illustrate how to choose resistor values to set reference voltage for the simple case where no LED intensity adjustment is required. A LED current of 10 mA to 20 mA generally produces adequate illumination. Having 10V full-scale across the internal voltage divider gives best accuracy by keeping signal level high relative to the offset voltage of the internal comparators. However, this causes 1 mA to flow from pin 7 into the divider which means that the LED current will be at least 10 mA. R1 will typically be between 1 k and 5 k. To trim the reference voltage, vary R2. The current in Figure 11 shows how to add a LED intensity control which can vary LED current from 5 mA to 28 mA. Choosing VREF = 5V lowers the current drawn by the ladder, increasing the intensity adjustment range. The reference adjustment has some effect on LED intensity but the reverse is not true. 00797118 5 mA ILED 28 mA @ VREF = 5V FIGURE 11. Varying LED Intensity Multiple Drivers Figure 12 shows how to obtain a common reference trim and intensity control for two drivers. The two ICs may be connected in cascade or may be handling separate channels for stereo. This technique can be extended for larger numbers of drivers by varying the values of R1, R2 and R3. Because the LM3915 has a greater ladder resistance, R5 was picked less than R7 in such a way as to provide equal reference load currents. The ICs' internal references track within 100 mV so that worst case error from chip to chip is only 0.2 dB for VREF = 5V. The scheme in Figure 13 is useful when the reference and LED intensity must be adjusted independently over a wide range. The RHI voltage can be adjusted from 1.2V to 10V with no effect on LED current. Since the internal divider here does not load down the reference, minimum LED current is much lower. At the minimum recommended reference load of 80 A, LED current is about 0.8 mA. The resistor values shown give a LED current range from 1.5 mA to 25 mA. At the low end of the intensity adjustment, the voltage drop across the 510 current-sharing resistors is so small that chip to chip variation in reference voltage may yield a visible variation in LED intensity. The optional approach shown of connecting the bottom end of the intensity control pot to a negative supply overcomes this problem by allowing a larger voltage drop across the (larger) current-sharing resistors. 00797117 FIGURE 10. Design Equations for Fixed LED Intensity www.national.com 14 LM3916 Application Hints (Continued) 00797119 5 mA ILED 28 mA VREF = 5V FIGURE 12. Independent Adjustment of Reference Voltage and LED Intensity for Multiple Drivers 00797120 1.25V VREF 10V 1.5 mA ILED 25 mA Optional circuit for improved intensity matching at low currents. See text. FIGURE 13. Wide-Range Adjustment of Reference Voltage and LED intensity for Multiple Drivers shown in Figure 14. The signal can be a triangle, sawtooth or sine wave from 60 Hz to 1 kHz. The display can be run in either dot or bar mode. Other Applications For increased resolution, it's possible to obtain a display with a smooth transition between LEDs. This is accomplished by superimposing an AC waveform on top of the input level as 15 www.national.com LM3916 Other Applications (Continued) 00797121 FIGURE 14. 0V to 10V VU Meter with Smooth Transitions www.national.com 16 Adjust R3 for 3 dB difference between LED #11 and LED #12 *See Application Hints for optional Peak or Average Detector. This application shows that the LED supply requires minimal filtering. Typical Applications Extended Range VU Meter (Dot Mode) 00797122 LM3916 17 www.national.com www.national.com 18 (Continued) See Application Hints for optional peak or average detector. *OPTIONAL SHUNTS 100 A auxiliary sink current away from LED #1. D1, D2: 1N914 or 1N4148 Typical Applications Extended Range VU Meter (Dot Mode) 00797123 LM3916 LM3916 Typical Applications (Continued) Driving Vacuum Fluorescent Display 00797124 R7 thru R15: 10k 10% D1, D2: 1N914 or 1N4148 *Half-wave peak detector. See Application Hints. 19 www.national.com LM3916 Typical Applications (Continued) Indicator and Alarm, Full-Scale Changes Display From Dot to Bar 00797125 *The input to the Dot-Bar switch may be taken from cathodes of other LEDs. Display will change to bar as soon as the LED so selected begins to light. **Optional. Shunts 100 A auxiliary sink current away from LED #1. www.national.com 20 (Continued) *See Application Hints for optional peak or average detector. Typical Applications High Resolution VU Meter (Bar Mode) 00797126 LM3916 21 www.national.com www.national.com 22 (Continued) See Application Hints for optional peak or average detector. *Optional shunts 100 A auxiliary sink current away from LED #1. Typical Applications High Resolution VU Meter (Dot Mode) 00797127 LM3916 LM3916 Typical Applications (Continued) Displaying Additional Levels 00797128 23 www.national.com LM3916 Typical Applications (Continued) Operating with a High Voltage Supply (Dot Mode Only) 00797129 The LED currents are approximately 10 mA, and LM3916 outputs operate in saturation for minimum dissipation. *This point is partially regulated and decreases in voltage with temperature. Voltage requirements of the LM3916 also decrease with temperature. Low Current Bar Mode Display 00797130 Supply current drain is only 20 mA with ten LEDs illuminated @ 16 mA. www.national.com 24 LM3916 Typical Applications (Continued) Driving Liquid Crystal Display 00797131 Bar Display with Alarm Flasher 00797132 Full-scale causes the full bar display to flash. If the junction of R1 and C1 is connected to a different LED cathode, the display will flash when that LED lights, and at any higher input signal. 25 www.national.com LM3916 Connection Diagram Dual-In-Line Package 00797133 Top View Order Number LM3916N-1 See NS Package Number NA18A Order Number LM3916N * See NS Package Number N18A *Discontinued, Life Time Buy date 12/20/99 measured at the current source outputs. As the forward voltage of an LED does not change significantly with a small change in forward current, this is equivalent to changing the voltage at the LED anodes by the same amount. Line Regulation: The average change in reference output voltage (VREF) over the specified range of supply voltage (V+). Load Regulation: The change in reference output voltage over the specified range of load current (IL(REF)). Offset Voltage: The differential input voltage which must be applied to each comparator to bias the output in the linear region. Most significant error when the voltage across the internal voltage divider is small. Specified and tested with pin 6 voltage (VRHI) equal to pin 4 voltage (VRLO). Relative Accuracy: The difference between any two adjacent threshold points. Specified and tested with 10V across the internal voltage divider so that resistor ratio matching error predominates over comparator offset voltage. Definition of Terms Absolute Accuracy: The difference between the observed threshold voltage and the ideal threshold voltage for each comparator. Specified and tested with 10V across the internal voltage divider so that resistor ratio matching error predominates over comparator offset voltage. Adjust Pin Current: Current flowing out of the reference amplifier pin when the reference amplifier is in the linear region. Comparator Gain: The ratio of the change in output current (ILED) to the change in input voltage (VIN) required to produce it for a comparator in the linear region. Dropout Voltage: The voltage measured at the current source outputs required to make the output current fall by 10%. Input Bias Current: Current flowing out of the signal input when the input buffer is in the linear region. LED Current Regulation: The change in output current over the specified range of LED supply voltage (VLED) as www.national.com 26 LM3916 Physical Dimensions inches (millimeters) unless otherwise noted Note: Unless otherwise specified. 1. Standard Lead Finish: 200 microinches /5.08 micrometer minimum lead/tin 37/63 or 15/85 on alloy 42 or equivalent or copper 2. Reference JEDEC registration MS-001, Variation AC, dated May 1993. Molded Dual-In-Line Package (N) Order Number LM3916N-1 NS Package Number NA18A 27 www.national.com LM3916 Dot/Bar Display Driver Physical Dimensions inches (millimeters) unless otherwise noted (Continued) Molded Dual-In-Line Package (N) Order Number LM3916N * NS Package Number N18A *Discontinued, Life Time Buy date 12/20/99 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated