This is information on a product in full production.
May 2012 Doc ID 15382 Rev 3 1/16
16
2N2907AHR
Hi-Rel 60 V - 0.6 A PNP transistor
Datasheet — production data
Features
■Linear gain characteristics
■Hermetic packages
■ESCC and JANS qualified
■European preferred part list EPPL
Description
The 2N2907AHR is a silicon planar PNP
transistor specifically designed and housed in
hermetic packages for aerospace and Hi-Rel
applications. It is available in the JAN qualification
system (MIL-PRF19500 compliance) and in the
ESCC qualification system (ESCC 5000
compliance). In case of discrepancies between
this datasheet and the relevant agency
specification, the latter takes precedence.
Figure 1. Internal schematic diagram
Parameter Value
BVCEO 60 V
IC (max) 0.6 A
HFE at 10 V - 150 mA > 100
TO-18
LCC-3
3
1
2
3
1
2
LCC-3UB
3
1
2
4
Pin 4 in LCC-3UB is connected to the metallic lid.
Table 1. Device summary(1)
Order codes Qualification Agency spec. Package Radiation level EPPL
JANS2N2907A JANS MIL-PRF-19500/291 LCC-3UB
-
-
2N2907AUB
ESCC 5201/001
LCC-3UB Yes
SOC2907A LCC-3 Yes
2N2907AHR TO-18 -
1. Contact ST sales office for information about the specific conditions for products in die form and other JAN quality levels.
www.st.com
Contents 2N2907AHR
2/16 Doc ID 15382 Rev 3
Contents
1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 JANS electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2 ESCC electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5 Shipping details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.1 Data code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.2 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2N2907AHR Electrical ratings
Doc ID 15382 Rev 3 3/16
1 Electrical ratings
Table 2. Absolute maximum ratings
Symbol Parameter Value Unit
VCBO Collector-base voltage (IE = 0) -60 V
VCEO Collector-emitter voltage (IB = 0) -60 V
VEBO Emitter-base voltage (IC = 0) -5 V
IC
Collector current
for TO-18
for LCC-3 and LCC-3UB
-0.6
-0.5
A
A
PTOT
Total dissipation at Tamb ≤ 25 °C
ESCC: TO-18
LCC-3 and LCC-3UB
LCC-3 and LCC-3UB (1)
JANS: LCC-3UB
Total dissipation at Tcase ≤ 25 °C
ESCC: TO-18
1. When mounted on a 15 x 15 x 0.6 mm ceramic substrate.
0.4
0.4
0.73
0.5
1.8
W
Total dissipation at Tsp(IS) = 25 °C
JANS: LCC-3UB 1
Tstg Storage temperature -65 to 200 °C
TJMax. operating junction temperature 200 °C
Table 3. Thermal data
Symbol Parameter LCC-3
LCC-3UB TO-18 Unit
RthJC
Thermal resistance junction-case (max) for JANS - -
°C/W
Thermal resistance junction-case (max) for
ESCC -97
RthJSP(IS)
Thermal resistance junction-solder pad (infinite
sink) (max) for JANS 90 -
Thermal resistance junction-solder pad (infinite
sink) (max) for ESCC --
RthJA
Thermal resistance junction-ambient (max) for
JANS 325 -
Thermal resistance junction-ambient (max) for
ESCC
437
240(1)
1. When mounted on a 15 x 15 x 0.6 mm ceramic substrate.
437
Electrical characteristics 2N2907AHR
4/16 Doc ID 15382 Rev 3
2 Electrical characteristics(a)
JANS and ESCC version of the products are assembled and tested in compliance with the
agency specification it is qualified in. The electrical characteristics of each version are
provided in dedicated tables.
Tcase = 25 °C unless otherwise specified.
2.1 JANS electrical characteristics
a. For PNP type, voltage and current values are negative.
Table 4. JANS electrical characteristics
Symbol Parameter Test conditions Min. Typ. Max. Unit
ICBO
Collector cut-off
current (IE = 0)
VCB = 60 V
VCB = 50 V
VCB= 50 V Tamb = 150 °C
-
10
10
10
µA
nA
µA
ICES
Collector cut-off
current
(IE = 0)
VCE = 50 V - 50 nA
IEBO
Emitter cut-off current
(IC = 0)
VEB = 5 V
VEB = 4 V -10
50
µA
nA
V(BR)CEO (1)
Collector-emitter
breakdown voltage
(IB = 0)
IC = 10 mA 60 - V
VCE(sat) (1) Collector-emitter
saturation voltage
IC = 150 mA IB = 15 mA
IC = 500 mA IB = 50 mA -0.4
1.6
V
V
VBE(sat) (1) Base-emitter
saturation voltage
IC = 150 mA IB = 15 mA
IC=500mA IB =50mA
0.6 1.3
2.6 V
hFE (1) DC current gain
IC = 0.1 mA VCE = 10 V
IC = 1 mA VCE = 10 V
IC = 10 mA VCE = 10 V
IC = 150 mA VCE = 10 V
IC = 500 mA VCE = 10 V
IC = 10 mA VCE = 10 V
Tamb = -55 °C
75
100
100
100
50
50
-
450
300
hfe
Small signal current
gain
VCE = 20 V IC = 20 mA
f = 100 MHz
VCE = 10 V IC =1 mA
f = 1 kHz
2
100 -
Cobo
Output capacitance
(IE = 0)
VCB = 10 V
100 kHz ≤ f ≤ 1 MHz -8pF
2N2907AHR Electrical characteristics
Doc ID 15382 Rev 3 5/16
2.2 ESCC electrical characteristics
Cibo
Output capacitance
(IE = 0)
VEB = 2 V
100 kHz ≤ f ≤ 1 MHz -30pF
ton Tu r n- on t ime VCC = 30 V IC = 150 mA
IB1 = 15 mA -45ns
toff Turn-off time VCC = 30 V IC = 150 mA
IB1 = -IB2 = 15 mA - 300 ns
1. Pulsed duration = 300 µs, duty cycle ≤ 2 %
Table 4. JANS electrical characteristics (continued)
Symbol Parameter Test conditions Min. Typ. Max. Unit
Table 5. ESCC electrical characteristics
Symbol Parameter Test conditions Min. Typ. Max. Unit
ICBO
Collector cut-off
current (IE = 0)
VCB = 50 V
VCB= 50 V Tamb = 150 °C -10
10
nA
µA
V(BR)CBO
Collector-base
breakdown voltage
(IE = 0)
IC = 10 µA 60 - V
V(BR)CEO (1)
1. Pulsed duration = 300 µs, duty cycle ≤ 2 %
Collector-emitter
breakdown voltage
(IB = 0)
IC = 10 mA 60 - V
V(BR)EBO
Emitter-base
breakdown voltage
(IC = 0)
IE = 10 µA 5 - V
VCE(sat) (1) Collector-emitter
saturation voltage IC = 150 mA IB = 15 mA - 0.4 V
VBE(sat) (1) Base-emitter
saturation voltage IC = 150 mA IB = 15 mA 0.87 1.3 V
hFE (1) DC current gain
IC = 0.1 mA VCE = 10 V
IC = 10 mA VCE = 10 V
IC = 150 mA VCE = 10 V
IC = 500 mA VCE = 10 V
75
100
100
50
-300
hfe
Small signal current
gain
VCE = 20 V IC = 20 mA
f = 100 MHz 2-
Cobo
Output capacitance
(IE = 0)
VCB = 10 V
100 kHz ≤ f ≤ 1 MHz -8pF
ton Tu r n- on t ime VCC = 30 V IC = 150 mA
IB1 = 15 mA -45ns
toff Turn-off time VCC = 30 V IC = 150 mA
IB1 = -IB2 = 15 mA - 300 ns
Electrical characteristics 2N2907AHR
6/16 Doc ID 15382 Rev 3
2.3 Electrical characteristics (curves)
Figure 2. DC current gain (VCE=1 V) Figure 3. DC current gain (VCE=10 V)
Figure 4. Collector emitter saturation
voltage
Figure 5. Base emitter saturation
voltage (hFE=10)
!-V
!-V
!-V
!-V
2N2907AHR Electrical characteristics
Doc ID 15382 Rev 3 7/16
2.4 Test circuits
Figure 6. JANS saturated turn-on switching time test circuit
Figure 7. JANS saturated turn-off switching time test circuit
NOTES:
1. The rise time (tr) of the applied pulse shall be ≤ 2.0 ns, duty cycle ≤ 2 percent and the generator
source impedance shall be 50 ohms.
2. Sampling oscilloscope: Zin ≥ 100 K ohms, Cin ≤ 12 pF, rise time ≤ 5 ns.
NOTES:
1. The rise time (t
r
) of the applied pulse shall be ≤ 2.0 ns, duty cycle ≤ 2 percent and the generator
source impedance shall be 50 ohms.
2. Sampling oscilloscope: Z
in
≥ 100 K ohms, C
in
≤ 12 pF, rise time ≤ 5 ns.
Electrical characteristics 2N2907AHR
8/16 Doc ID 15382 Rev 3
Figure 8. ESCC resistive load switching test circuit
1. Fast electronic switch
2. Non-inductive resistor
2N2907AHR Package mechanical data
Doc ID 15382 Rev 3 9/16
3 Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Table 6. Product mass summary
Package Mass (g)
LCC-3UB 0.06
LCC-3 0.06
TO-18 0.40
Package mechanical data 2N2907AHR
10/16 Doc ID 15382 Rev 3
Figure 9. LCC-3UB drawings
Table 7. LCC-3UB mechanical data
Dim.
mm.
Min. Typ. Max.
A 1.16 1.42
C 0.46 0.51 0.56
D 0.56 0.76 0.96
E 0.92 1.02 1.12
F 1.95 2.03 2.11
G 2.92 3.05 3.18
I 2.41 2.54 2.67
J 0.42 0.57 0.72
K 1.37 1.52 1.67
L 0.41 0.51 0.61
M 2.46 2.54 2.62
N 1.81 1.91 2.01
r 0.20
r1 0.30
r2 0.56
2N2907AHR Package mechanical data
Doc ID 15382 Rev 3 11/16
Figure 10. LCC-3 drawings
Table 8. LCC-3 mechanical data
Dim.
mm.
Min. Typ. Max.
A 1.16 1.42
C 0.45 0.50 0.56
D 0.60 0.76 0.91
E 0.91 1.01 1.12
F 1.95 2.03 2.11
G 2.92 3.05 3.17
I 2.41 2.54 2.66
J 0.42 0.57 0.72
K 1.37 1.52 1.67
L 0.40 0.50 0.60
M 2.46 2.54 2.62
N 1.80 1.90 2.00
R 0.30
21
3
Package mechanical data 2N2907AHR
12/16 Doc ID 15382 Rev 3
Figure 11. TO-18 drawings
Table 9. TO-18 mechanical data
Dim.
mm.
Min. Typ. Max.
A 12.7
B 0.49
D 5.3
E 4.9
F 5.8
G 2.54
H1.2
I1.16
L 45°
Order codes 2N2907AHR
13/16 Doc ID 15382 Rev 3
4 Order codes
Contact ST sales office for information about the specific conditions for:
– Products in die form
– Other JANS quality levels
– Tape and reel packing
Table 10. Order codes
Part number Agency specification EPPL Quality level Radiation
level Package Lead Finish Marking(1) Packing
J2N2907AUB1
-
-Engineering model
JANS
-
LCC-3UB Gold J2N2907A Waffle pack
2N2907AUB1 - Engineering model
ESCC LCC-3UB Gold U03 Waffle pack
SOC2907A - Engineering model
ESCC LCC-3 Gold P03 Waffle pack
JANS2N2907AUBG MIL-PRF-19500/291 - JANS flight LCC-3UB Gold JS2907 Waffle pack
JANS2N2907AUBT MIL-PRF-19500/291 - LCC-3UB Solder Dip JS2907 Waffle pack
2N2907AUB06 5202/001/06 Yes
ESCC flight
LCC-3UB Gold 520200106 Waffle pack
2N2907AUB07 5202/001/07 Yes LCC-3UB Solder Dip 520200107 Waffle pack
SOC2907AHRB 5202/001/04 or 05 (2) Yes LCC-3 Gold or
Solder Dip (2)
520200104
or 05 (2) Waffle pack
2N2907AHR 5202/001/01 or 02 (2) -TO-18
Gold or
Solder Dip (2)
520200101
or 02 (2) Strip pack
1. Specific marking only. The full marking includes in addition:
For the engineering models : ST logo, date code, country of origin (FR).
For ESCC flight parts : ST logo, date code, country of origin (FR), ESA logo, serial number of the part within the assembly lot.
For JANS flight parts : ST logo, date code, country of origin (FR), manufacturer code (CSTM), serial number of the part within the assembly lot.
2. Depending ESCC part number mentioned on the purchase order.
Shipping details 2N2907AHR
14/16 Doc ID 15382 Rev 3
5 Shipping details
5.1 Data code
Data code is structured as described below:
– EM (ESCC and JANS) xyywwz
– ESCC Flight yywwz
– JANS Flight xyywwz
where:
5.2 Documentation
xyywwz
3: EM
W: flight part/ diffused
in Singapore
Last two digits year
Week digits
Lot index in the week
Table 11. Documentation provided for each type of product
Quality level Radiation level Documentation
Engineering model - -
JANS Flight - Certificate of conformance
ESCC Flight - Certificate of conformance
2N2907AHR Revision history
Doc ID 15382 Rev 3 15/16
6 Revision history
Table 12. Document revision history
Date Revision Changes
09-Feb-2009 1 Initial release
30-Nov-2011 2
– Modified Table 1 on page 1
– Minor text changes in the document title and description on the
coverpage
14-May-2012 3
New package inserted (LCC-3UB).
Updated:
–Table 1: Device summary, Table 2: Absolute maximum ratings and
Table 3: Thermal data.
–Section 2: Electrical characteristics and Section 3: Package
mechanical data.
Added:
–Section 4: Order codes and Section 5: Shipping details.
2N2907AHR
16/16 Doc ID 15382 Rev 3
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan -
Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
