Data Sheet
September 29, 2003
Document No: DS03-017 ver.0.6
PDF No: hw-hc_4-6a
HW/HC004/005/006 Series Power Modules; dc-dc Converters
18-36 Vdc & 36-75 Vdc Input; 1.0Vdc to 5Vdc Output; 4A to 6A
* UL is a registered trademark of Underwriters Laboratories, Inc.
CSA is a registered trademark of Canadian Standards Association.
VDE is a trademark of Verband Deutscher Elektrotechniker e.V.
§ This product is intended for integration into end-user equipment. All the required procedures for CE marking of end-user equipment should be followed. (The CE mark is
placed on selected products.)
** ISO is a registered trademark of the International Organization of Standards
Applications
Distributed power architectures
Wireless Networks
Access and Optical Network Equipment
Enterprise Networks
Latest generation IC’s (DSP, FPGA, ASIC) and
Microprocessor powered applications.
Options
Remote On/Off logic (positive or negative)
Surface Mount (-S Suffix)
Basic Insulation Approved (-B Suffix)
Additional Vout+ pin (-3 Suffix)
Features
Delivers up to 6A output current
5.0V (4A), 3.3V (5A), 2.5V – 1.0V (6A each)
High efficiency – 89% at 5V full load
Low Output Voltage – supports migration to future
IC supply voltages down to 1.0V
Low output ripple and noise
Small size and low profile:
47.2 mm x 29.5 mm x 8.5 mm
(1.86 x 1.16 x 0.335 in)
Surface mount or through hole
Cost efficient open frame design
Single tightly regulated output
Remote On/Off
Output overcurrent protection
Output overvoltage protection
Overtemperature protection
Output voltage adjustment (+10%, -10%)
Wide operating temperature range (-40°C to 100°C)
Meets the voltage isolation requirements for
ETSI 300-132-2 and complies with and is licensed
for Basic Insulation rating per EN60950 (-B option)
UL* 60950 Recognized, CSA C22.2 No. 60950-00
Certified, and VDE 0805 (IEC60950, 3rd Ed)
Licensed
CE mark meets 73/23/EEC and 93/68/EEC
directives§ (HW series only)
ISO** 9001 and ISO 14001 certified manufacturing
facilities
Description
The HW/HC series power modules are isolated dc-dc converters that operate over a wide input voltage range of 18
to 36 Vdc (HC) or 36 to 75 Vdc (HW) and provide one precisely regulated output. The output is fully isolated from
the input, allowing versatile polarity configurations and grounding connections. The modules exhibit high efficiency,
e.g. typical efficiency of 87% 3.3V/5A, 86% at 2.5V/6A. Built-in filtering for both input and output minimizes the need
for external filtering. These open frame modules are available either in surface-mount (-S) or in through-hole form.
Standard features include Remote On/Off, output voltage adjust, overvoltage, overcurrent and overtemperature
protection.
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
2 Tyco Electronics Power Systems.
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are
absolute stress ratings only, functional operation of the device is not implied at these or any other conditions in
excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for
extended periods can adversely affect the device reliability.
Parameter Device Symbol Min Max Unit
Input Voltage HC VIN -0.3 50 Vdc
Continuous HW VIN -0.3 80 Vdc
Transient (100ms) HW VIN, trans -0.3 100 Vdc
Operating Ambient Temperature All TA -40 100 °C
(see Thermal Considerations section)
Storage Temperature All Tstg -55 125 °C
I/O Isolation Voltage All 2250 Vdc
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions.
Parameter Device Symbol Min Typ Max Unit
Operating Input Voltage HC VIN 18 24 36 Vdc
HW VIN 36 54 75 Vdc
Maximum Input Current HC IIN,max 1.75 Adc
(VIN=0V to 75V, IO=IO, max) HW IIN,max 0.85 Adc
Inrush Transient All I2t 1 A2s
Input Reflected Ripple Current, peak-to-peak
(5Hz to 20MHz, 12µH source impedance; VIN=0V to
75V, IO= IOmax ; see Figure 9)
All 5 mAp-p
Input Ripple Rejection (120Hz) All 50 dB
EMC, EN55022
See EMC Considerations section
CAUTION: This power module is not internally fused. An input line fuse must always be used.
This power module can be used in a wide variety of applications, ranging from simple standalone operation to an
integrated part of a sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included,
however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies
require a fast-acting fuse with a maximum rating of 3A (see Safety Considerations section). Based on the information
provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating
can be used. Refer to the fuse manufacturer’s data sheet for further information.
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 3
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
Output Voltage Set-point
5V, 3.3V
2.5V, 2.0V,
1.8V, 1.5V
VO, set -1.0 +1.0 % VO, nom
(VIN=VIN,nom, IO=IO, max, Tref=25°C) 1.2V, 1.0V VO, set -1.25 +1.25 % VO, nom
Output Voltage All VO -3.0 +3.0 % VO, nom
(Over all operating input voltage, resistive load,
and temperature conditions until end of life)
Adjustment Range All VO -10.0 +10.0 % VO, nom
Selected by external resistor
Output Regulation
Line (VIN=VIN, min to VIN, max) All
10 mV
Load (IO=IO, min to IO, max) All
15 mV
Temperature (Tref=TA, min to TA, max) All
1.00 %
Output Ripple and Noise on nominal output
(VIN=VIN, nom and IO=IO, min to IO, max)
RMS (5Hz to 20MHz bandwidth) All 8 15 mVrms
Peak-to-Peak (5Hz to 20MHz bandwidth) All 25 50 mVpk-pk
External Capacitance All CO, max 470 µF
Output Current 5V Io 0 4.0 Adc
3.3V Io 0 5.0 Adc
2.5V, 2.0,
1.8V, 1.5V,
1.2V, 1.0V
Io 0 6.0 Adc
Output Current Limit Inception 5V IO, lim 6.5 Adc
( Hiccup Mode ) 3.3V IO, lim 7 Adc
2.5V, 2.0V,
1.8V, 1.5V,
1.2V, 1.0V
IO, lim 8.5 Adc
Output Short-Circuit Current 5V IO, s/c 2.4 A rms
(VO250mV) ( Hiccup Mode ) 3.3V IO, s/c 2.4 A rms
2.5V, 2.0V,
1.8V, 1.5V,
1.2V, 1.0V
IO, s/c 2.8 A rms
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
4 Tyco Electronics Power Systems.
Electrical Specifications (continued)
Parameter Device Symbol Min Typ Max Unit
HW 5V η 89.0 %
Efficiency HW 3.3V η 87.0 %
VIN=VIN, nom, TA=25°C HW 2.5V η 86.0 %
IO=IO, max , VO= VO,set HW 2.0V η 82.0 %
HW 1.8V η 82.0 %
HW 1.5V η 80.0 %
HW 1.2V η 77.0 %
HW 1.0V η 75.0 %
HC 5V η 88.0 %
HC 3.3V η 86.0 %
Switching Frequency All HW fsw 300 kHz
All HC fsw 380 kHz
Dynamic Load Response
(Io/t=1A/µs; Vin=Vin,nom; TA=25°C) 5V, 3.3V Vpk 100 mV
Load Change from Io= 50% to 75% of Io,max:
2.5V, 2.0V,
1.8V, 1.5V,
1.2V, 1.0V
Vpk 80 mV
Peak Deviation
Settling Time (Vo<10% peak deviation) All ts 100 µs
Dynamic Line Response
(Vin / t0.5V/µs; Vin=Vin,nom; TA=25°C)
Peak Deviation All Vpk 0.6 2
%Vo,
set
Settling Time (Vo<10% peak deviation) All ts 150 1000 µs
Isolation Specifications
Parameter Symbol Min Typ Max Unit
Isolation Capacitance Ciso 200 pF
Isolation Resistance Riso 10 M
General Specifications
Parameter Min Typ Max Unit
Calculated MTBF (for HW005A0F1-S in accordance with Lucent
RIN 6: IO=80% of IO, max, TA=25°C, airflow=1m/s) >4,000,000 Hours
Weight 13 g (oz.)
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 5
Feature Specifications
Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature
conditions. See Feature Descriptions for additional information.
Parameter Device Symbol Min Typ Max Unit
Remote On/Off Signal Interface
(VIN=VIN, min to VIN, max ; open collector or equivalent,
Signal referenced to VIN- terminal)
Negative Logic: device code suffix “1”
Logic Low = module On, Logic High = module Off
Positive Logic: No device code suffix required
Logic Low = module Off, Logic High = module On
Logic Low Specification
Remote On/Off Current – Logic Low All Ion/off 0.15 1.0 mA
On/Off Voltage:
Logic Low All Von/off 0.0 1.2 V
Logic High – (Typ = Open Collector) All Von/off 5.8 15 V
Logic High maximum allowable leakage current All Ion/off 10 µA
Turn-On Delay and Rise Times
(IO=IO, max)
Tdelay 100 ms
5V, 3.3V Trise 40 ms
Tdelay = Time until VO = 10% of VO,set from either
application of Vin with Remote On/Off set to On or
operation of Remote On/Off from Off to On with Vin
already applied for at least one second.
Tdelay 12 ms
Trise = time for VO to rise from 10% of VO,set to 90%
of VO,set.
2.5V, 2.0V,
1.8V, 1.5V,
1.2V, 1.0V
Trise 3 ms
5V VO, limit 7.0 V
Output Overvoltage Protection# 3.3V 4.6 V
2.5V
3.5 V
Values are the same for HW and HC codes 2.0V 3.2 V
1.8V
2.8 V
1.5V
2.5 V
1.2V
2.0 V
1.0V
1.8 V
Overtemperature Protection All Tref 125 °C
(See Feature Descriptions)
Input Undervoltage Lockout
Turn-on Threshold All HW 33 36 V
Turn-off Threshold All HW 27 30 V
Turn-on Threshold All HC 17 18 V
Turn-off Threshold All HC 13.5 15 V
# More accurate Overvoltage protection can be accomplished externally by means of the remote On/Off pin.
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
6 Tyco Electronics Power Systems
Characteristic Curves
The following figures provide typical characteristics for the HW004A0A (5.0V, 4A) at 25ºC. The figures are identical
for either positive or negative Remote On/Off logic.
70
72
74
76
78
80
82
84
86
88
90
01234
VI
= 3 6 V
VI = 54 V
VI
= 75V
0
1
2
3
4
5
0 10 203040 50 60 708090100110
3.0 m/s (600 ft./min.)
2.0 m/s (400 ft./min.)
1.0 m/s (200 ft./min.)
NATURAL CONVECTION
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 1. Converter Efficiency versus Output Current Figure 4. Derating Output Current versus Local
Ambient Temperature and Airflow
OUTPUT VOLTAGE,
VO (V) (20mV/div)
TIME, t (1µs/div)
INPUT VOLTAGE OUTPUT VOLTAGE
VIN (V) (50V/div) VO (V) (2V/div)
TIME, t (20ms/div)
Figure 2. Typical Output Ripple and Noise. Figure 5. Typical Start-Up with application of Vin.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (1A/div) VO (V) (50mV/div)
TIME, t (50µs/div)
On/Off VOLTAGE OUTPUT VOLTAGE
VON/OFF(V) (5V/div) VO (V) (2V/div)
TIME, t (20ms/div)
Figure 3. Transient Response to Dynamic Load
Change from 50% to 75% to 50% of full load.
Figure 6. Typical Start-Up Using Remote On/Off,
negative logic version shown.
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 7
Characteristic Curves (continued)
The following figures provide typical characteristics for the HW005A0F (3.3V, 5A) at 25ºC. The figures are identical
for either positive or negative Remote On/Off logic.
70
72
74
76
78
80
82
84
86
88
90
012345
VI
= 36V
VI = 54 V
VI
= 75V
0
1
2
3
4
5
6
0 10 203040 50 60 708090100110
3.0 m/ s (600 f t ./min.)
2.0 m/ s (400 f t ./min.)
1.0 m/s (200 f t ./ min.)
NATURAL CONVECTION
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 7. Converter Efficiency versus Output Current Figure 10. Derating Output Current versus Local
Ambient Temperature and Airflow
OUTPUT VOLTAGE,
VO (V) (20mV/div)
TIME, t (1µs/div)
INPUT VOLTAGE, OUTPUT VOLTAGE
VIN (V) (50V/div) VO (V) (1V/div)
TIME, t (20ms/div)
Figure 8. Typical Output Ripple and Noise. Figure 11. Typical Start-Up with application of Vin.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (50mV/div)
TIME, t (50µs/div)
On/Off VOLTAGE OUTPUT VOLTAGE
VON/OFF(V) (5V/div) VO (V) (1V/div)
TIME, t (20ms/div)
Figure 9. Transient Response to Dynamic Load
Change from 50% to 75% to 50% of full load.
Figure 12. Typical Start-Up Using Remote On/Off,
negative logic version shown.
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
8 Tyco Electronics Power Systems
Characteristic Curves (continued)
The following figures provide typical characteristics for the HW006A0G (2.5V, 6A) at 25ºC. The figures are identical
for either positive or negative Remote On/Off logic.
68
70
72
74
76
78
80
82
84
86
88
0 1234 56
VI
= 3 6 V
VI = 54 V
VI
= 75V
0
1
2
3
4
5
6
7
0 10 2030405060708090100110
2.0 m/s (400 ft./min.)
1.0 m/s (200 ft./min.)
NATURAL CONVECTION
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 13. Converter Efficiency versus Output Current Figure 16. Derating Output Current versus Local
Ambient Temperature and Airflow
OUTPUT VOLTAGE,
VO (V) (20mV/div)
TIME, t (1µs/div)
INPUT VOLTAGE, OUTPUT VOLTAGE
VIN (V) (50V/div) VO (V) (1V/div)
TIME, t (5ms/div)
Figure 14. Typical Output Ripple and Noise. Figure 17. Typical Start-Up with application of Vin.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (50mV/div)
TIME, t (50µs/div)
On/Off VOLTAGE, OUTPUT VOLTAGE
VON/OFF(V) (5V/div) VO (V) (1V/div)
TIME, t (5ms/div)
Figure 15. Transient Response to Dynamic Load
Change from 50% to 75% to 50% of full load.
Figure 18. Typical Start-Up Using Remote On/Off,
negative logic version shown.
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 9
Characteristic Curves (continued)
The following figures provide typical characteristics for the HW006A0D (2.0V, 6A) at 25ºC. The figures are identical
for either positive or negative Remote On/Off logic.
66
68
70
72
74
76
78
80
82
84
86
0 1234 56
VI = 3 6 V
VI = 54 V
VI = 75V
0
1
2
3
4
5
6
7
0 10 203040 50 60 708090100110
2.0 m/s (4 00 f t./ min.)
1.0 m/ s (20 0 f t ./ min.)
NATURAL CONVECTION
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 19. Converter Efficiency versus Output Current Figure 22. Derating Output Current versus Local
Ambient Temperature and Airflow
OUTPUT VOLTAGE,
VO (V) (20mV/div)
TIME, t (1µs/div)
INPUT VOLTAGE, OUTPUT VOLTAGE
VIN (V) (25V/div) VO (V) (500mV/div)
TIME, t (5ms/div)
Figure 20. Typical Output Ripple and Noise. Figure 23. Typical Start-Up with application of Vin.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (50mV/div)
TIME, t (50µs/div)
On/Off VOLTAGE, OUTPUT VOLTAGE
VON/OFF(V) (5V/div) VO (V) (500mV/div)
TIME, t (5ms/div)
Figure 21. Transient Response to Dynamic Load
Change from 50% to 75% to 50% of full load.
Figure 24. Typical Start-Up Using Remote On/Off,
negative logic version shown.
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
10 Tyco Electronics Power Systems
Characteristic Curves (continued)
The following figures provide typical characteristics for the HW006A0Y (1.8V, 6A) at 25ºC. The figures are identical
for either positive or negative Remote On/Off logic.
66
68
70
72
74
76
78
80
82
84
86
01234 56
VI = 3 6 V
VI = 54 V
VI = 75V
0
1
2
3
4
5
6
7
0 10 203040 50 60 708090100110
2.0 m/s (4 00 f t./ min.)
1.0 m/ s (20 0 f t ./ min.)
NATURAL CONVECTION
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 25. Converter Efficiency versus Output Current Figure 28. Derating Output Current versus Local
Ambient Temperature and Airflow
OUTPUT VOLTAGE,
VO (V) (20mV/div)
TIME, t (1µs/div)
INPUT VOLTAGE, OUTPUT VOLTAGE
VIN (V) (25V/div) VO (V) (500mV/div)
TIME, t (5ms/div)
Figure 26. Typical Output Ripple and Noise. Figure 29. Typical Start-Up with application of Vin.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (50mV/div)
TIME, t (50µs/div)
On/Off VOLTAGE, OUTPUT VOLTAGE
VON/OFF(V) (5V/div) VO (V) (500mV/div)
TIME, t (5ms/div)
Figure 27. Transient Response to Dynamic Load
Change from 50% to 75% to 50% of full load.
Figure 30. Typical Start-Up Using Remote On/Off,
negative logic version shown.
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 11
Characteristic Curves (continued)
The following figures provide typical characteristics for the HW006A0M (1.5V, 6A) at 25ºC. The figures are identical
for either positive or negative Remote On/Off logic.
66
68
70
72
74
76
78
80
82
84
86
0 1234 56
VI = 3 6 V
VI = 54 V
VI = 75V
0
1
2
3
4
5
6
7
0 10 203040 50 60 708090100110
2.0 m/s (4 00 f t./ min.)
1.0 m/ s (20 0 f t ./ min.)
NATURAL CONVECTION
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 31. Converter Efficiency versus Output Current Figure 34. Derating Output Current versus Local
Ambient Temperature and Airflow
OUTPUT VOLTAGE,
VO (V) (20mV/div)
TIME, t (1µs/div)
INPUT VOLTAGE, OUTPUT VOLTAGE
VIN (V) (25V/div) VO (V) (500mV/div)
TIME, t (5ms/div)
Figure 32. Typical Output Ripple and Noise. Figure 35. Typical Start-Up with application of Vin.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (50mV/div)
TIME, t (50µs/div)
On/Off VOLTAGE, OUTPUT VOLTAGE
VON/OFF(V) (5V/div) VO (V) (500mV/div)
TIME, t (5ms/div)
Figure 33. Transient Response to Dynamic Load
Change from 50% to 75% to 50% of full load.
Figure 36. Typical Start-Up Using Remote On/Off,
negative logic version shown.
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
12 Tyco Electronics Power Systems
Characteristic Curves (continued)
The following figures provide typical characteristics for the HW006A0P (1.2V, 6A) at 25ºC. The figures are identical
for either positive or negative Remote On/Off logic.
60
62
64
66
68
70
72
74
76
78
80
0 1234 56
V I
= 3 6 V
V I = 54 V
V I
= 75V
0
1
2
3
4
5
6
7
0 10 2030405060708090100110
3.0 m/s (60 0 f t ./ min.)
2.0 m/s (40 0 f t ./ min.)
1.0 m/s (200 ft./min.)
NATURAL CONVECTION
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 37. Converter Efficiency versus Output Current Figure 40. Derating Output Current versus Local
Ambient Temperature and Airflow
OUTPUT VOLTAGE,
VO (V) (20mV/div)
TIME, t (1µs/div)
INPUT VOLTAGE, OUTPUT VOLTAGE
VIN (V) (50V/div) VO (V) (500mV/div)
TIME, t (5ms/div)
Figure 38. Typical Output Ripple and Noise. Figure 41. Typical Start-Up with application of Vin.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (50mV/div)
TIME, t (50µs/div)
On/Off VOLTAGE, OUTPUT VOLTAGE
VON/OFF(V) (5V/div) VO (V) (500mV/div)
TIME, t (5ms/div)
Figure 39. Transient Response to Dynamic Load
Change from 50% to 75% to 50% of full load.
Figure 42. Typical Start-Up Using Remote On/Off,
negative logic version shown.
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 13
Characteristic Curves (continued)
The following figures provide typical characteristics for the HW006A0S1R0 (1.0V, 6A) at 25ºC. The figures are
identical for either positive or negative Remote On/Off logic.
60
62
64
66
68
70
72
74
76
78
80
0 1234 56
VI = 36V
VI = 54V
VI = 75V
0
1
2
3
4
5
6
7
0 10 203040 50 60 708090100110
3.0 m/s (600 ft./min.)
2.0 m/s (400 ft./min.)
1.0 m/s (200 f t ./ min.)
NATURAL CONVECTION
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 43. Converter Efficiency versus Output Current Figure 46. Derating Output Current versus Local
Ambient Temperature and Airflow
OUTPUT VOLTAGE,
VO (V) (20mV/div)
TIME, t (1µs/div)
INPUT VOLTAGE, OUTPUT VOLTAGE
VIN (V) (50V/div) VO (V) (500mV/div)
TIME, t (5ms/div)
Figure 44. Typical Output Ripple and Noise. Figure 47. Typical Start-Up with application of Vin.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (50mV/div)
TIME, t (50µs/div)
On/Off VOLTAGE, OUTPUT VOLTAGE
VON/OFF(V) (5V/div) VO (V) (500mV/div)
TIME, t (5ms/div)
Figure 45. Transient Response to Dynamic Load
Change from 50% to 75% to 50% of full load.
Figure 48. Typical Start-Up Using Remote On/Off,
negative logic version shown.
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
14 Tyco Electronics Power Systems
Characteristic Curves (continued)
The following figures provide typical characteristics for the HC004A0A (5.0V, 4A) at 25ºC. The figures are identical for
either positive or negative Remote On/Off logic.
70
72
74
76
78
80
82
84
86
88
90
01234
V I = 3 6 V
V I = 54 V
V I = 75V
0
1
2
3
4
5
0 10 2030405060708090100110
3.0 m/s (600 ft./min.)
2.0 m/s (400 ft./min.)
1.0 m/s (200 ft./min.)
Natural Convection
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 49. Converter Efficiency versus Output Current Figure 52. Derating Output Current versus Local
Ambient Temperature and Airflow
OUTPUT VOLTAGE,
VO (V) (20mV/div)
TIME, t (1µs/div)
INPUT VOLTAGE, OUTPUT VOLTAGE
VIN (V) (25V/div) VO (V) (2V/div)
TIME, t (20ms/div)
Figure 50. Typical Output Ripple and Noise. Figure 53. Typical Start-Up with application of Vin.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (1A/div) VO (V) (50mV/div)
TIME, t (50µs/div)
On/Off VOLTAGE, OUTPUT VOLTAGE
VON/OFF(V) (5V/div) VO (V) (2V/div)
TIME, t (20ms/div)
Figure 51. Transient Response to Dynamic Load
Change from 50% to 75% to 50% of full load.
Figure 54. Typical Start-Up Using Remote On/Off,
negative logic version shown.
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 15
Characteristic Curves (continued)
The following figures provide typical characteristics for the HC005A0F (3.3V, 5A) at 25ºC. The figures are identical for
either positive or negative Remote On/Off logic.
70
72
74
76
78
80
82
84
86
88
90
0 12345
V I = 36V
V I = 54 V
V I = 75V
0
1
2
3
4
5
6
0 10 2030405060708090100110
3.0 m/s (600 ft./min.)
2.0 m/s (400 ft./min.)
1.0 m/s (200 ft./min.)
Natural Convection
EFFICIENCY, η (%)
OUTPUT CURRENT, IO (A)
OUTPUT CURRENT, Io (A)
AMBIENT TEMPERATURE, TA OC
Figure 55. Converter Efficiency versus Output Current Figure 58. Derating Output Current versus Local
Ambient Temperature and Airflow
OUTPUT VOLTAGE,
VO (V) (20mV/div)
TIME, t (1µs/div)
INPUT VOLTAGE, OUTPUT VOLTAGE
VIN (V) (25V/div) VO (V) (1V/div)
TIME, t (20ms/div)
Figure 56. Typical Output Ripple and Noise. Figure 59. Typical Start-Up with application of Vin.
OUTPUT CURRENT, OUTPUT VOLTAGE
IO (A) (2A/div) VO (V) (50mV/div)
TIME, t (50µs/div)
On/Off VOLTAGE, OUTPUT VOLTAGE
VON/OFF(V) (5V/div) VO (V) (1V/div)
TIME, t (20ms/div)
Figure 57. Transient Response to Dynamic Load
Change from 50% to 75% to 50% of full load.
Figure 60. Typical Start-Up Using Remote On/Off,
negative logic version shown.
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
16 Tyco Electronics Power Systems
Test Configurations
TO OSCILLOSCOPE CURRENT PROBE
LTEST
12µH
BATTERY
CS 220µF
E.S.R.<0.1
@ 20°C 100kHz
33µF
VIN(+)
VIN(-)
NOTE: Measure input reflected ripple current with a simulated
source inductance (LTEST) of 12µH. Capacitor CS offsets
possible battery impedance. Measure current as shown
above.
Figure 61. Input Reflected Ripple Current Test Setup
VO
COM
RLOAD
SCOPE
COPPER STRIPS
1
µ
F10
µ
F
NOTE: Use a 1µF ceramic capacitor and a 10µF aluminium or
tantalum capacitor. The scope measurement should be
made using a BNC socket. Position the load 50mm to
75mm (2" to 3") from the module.
Figure 62. Output Ripple and Noise Test Setup
VO
COM
VIN
(
+
)
VIN
(
-
)
RLOAD
Rcontact Rdistribution
Rcontact Rdistribution
Rcontact
Rcontact
Rdistribution
Rdistribution
VIN VO
NOTE: All voltage measurements to be taken at the module
terminals, as shown above. If sockets are used then
Kelvin connections are required at the module terminals
to avoid measurement errors due to socket contact
resistance.
Figure 63. Output Voltage and Efficiency Test Setup
η =
VO. IO
VIN. IIN
x 100 %
Efficiency
Design Considerations
Input Source Impedance
The power module should be connected to a low
ac-impedance source. A highly inductive source
impedance can affect the stability of the power module.
For the test configuration in Figure 61, a 33µF
electrolytic capacitor (ESR<0.7 at 100kHz), mounted
close to the power module helps ensure the stability of
the unit. Consult the factory for further application
guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL 1950, CSA C22.2 No. 60950-00, and VDE
0805:2001-12 (IEC60950 3rd Ed).
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75Vdc), for the module’s output to be considered as
meeting the requirements for safety extra-low voltage
(SELV), all of the following must be true:
The input source is to be provided with reinforced
insulation from any other hazardous voltages, including the
ac mains.
One VIN pin and one VOUT pin are to be grounded, or both
the input and output pins are to be kept floating.
The input pins of the module are not operator accessible.
Another SELV reliability test is conducted on the whole
system (combination of supply source and subject
module), as required by the safety agencies, to verify that
under a single fault, hazardous voltages do not appear at
the module’s output.
Note: Do not ground either of the input pins of the
module without grounding one of the output pins.
This may allow a non-SELV voltage to appear
between the output pins and ground.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
For input voltages exceeding –60 Vdc but less than or
equal to –75 Vdc, these converters have been evaluated
to the applicable requirements of BASIC INSULATION
between secondary DC MAINS DISTRIBUTION input
(classified as TNV-2 in Europe) and unearthed SELV
outputs (-B option only).
"All flammable materials used in the manufacturing of
these modules are rated 94V-0 and UL60950 A.2 for
reduced thicknesses. The input to these units is to be
provided with a maximum 3A fast-acting fuse in the
unearthed lead."
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 17
Feature Descriptions
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal
current-limiting circuitry and can endure current limiting
continuously. At the point of current-limit inception, the
unit enters hiccup mode. The unit operates normally
once the output current is brought back into its specified
range. The average output current during hiccup is 10%
IO, max.
Remote On/Off
Two remote on/off options are available. Positive logic
turns the module on during a logic high voltage on the
ON/OFF pin, and off during a logic low. Negative logic
remote On/Off, device code suffix “1”, turns the module
off during a logic high and on during a logic low.
ON/OFF
VIN(+)
VIN
(
-
)
Ion/off
Von/off
VO
COM
Figure 64. Remote On/Off Implementation
To turn the power module on and off, the user must
supply a switch (open collector or equivalent) to control
the voltage (Von/off) between the ON/OFF terminal and
the VIN(-) terminal. Logic low is 0V Von/off 1.2V. The
maximum Ion/off during a logic low is 1mA, the switch
should be maintain a logic low level whilst sinking this
current.
During a logic high, the typical Von/off generated by the
module is 5.8V, and the maximum allowable leakage
current at Von/off = 5.8V is 10µA.
If not using the remote on/off feature:
For positive logic, leave the ON/OFF pin open.
For negative logic, short the ON/OFF pin to VIN(-).
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with a thermal shutdown circuit. The unit will
shutdown if the overtemperature threshold of 125 oC is
exceeded at the thermal reference point Tref . Once the
unit goes into thermal shutdown it will then wait to cool
before attempting to restart.
Input Undervoltage Lockout
At input voltages below the input undervoltage lockout
limit, the module operation is disabled. The module will
begin to operate at an input voltage above the
undervoltage lockout turn-on threshold.
Output Overvoltage Protection
The output overvoltage protection consists of circuitry
that internally clamps the output voltage. If a more
accurate output overvoltage protection scheme is
required then this should be implemented externally via
use of the remote on/off pin.
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
18 Tyco Electronics Power Systems
Feature Descriptions (continued)
Output Voltage Set-Point Adjustment
(Trim)
Trimming allows the output voltage set point to be
increased or decreased, this is accomplished by
connecting an external resistor between the TRIM pin
and either the VO(+) pin or the VO(-) pin (COM pin) .
VO(+)
VOTRIM
COM
Rtrim-down
LOAD
VIN(+)
ON/OFF
VIN(-)
Rtrim-up
Figure 65. Circuit Configuration to Trim Output
Voltage
Connecting an external resistor (Rtrim-down) between the
TRIM pin and the COM pin decreases the output voltage
set point. To maintain set point accuracy, the trim
resistor tolerance should be ±0.1%.
The relationship between the output voltage and the trim
resistor value for a % reduction in output voltage is:
Nominal 5V, 3.3V, 2.5V, 2.0V, 1.8V, & 1.5V modules:
Nominal 1.2V module:
Nominal 1.0V module:
Connecting an external resistor (Rtrim-up) between the
TRIM pin and the VO(+) pin increases the output voltage
set point. To maintain set point accuracy, the trim
resistor tolerance should be ±0.5%.
The relationship between the output voltage and the trim
resistor value for a % increase in output voltage is:
Nominal 5V, 3.3V, 2.5V, 2.0V, 1.8V, & 1.5V modules:
Nominal 1.2V module:
Nominal 1.0V module:
(VO refers to the nominal output voltage, i.e. 5.0V for VO
on an HW004A0A. % is the required % change in
output voltage, i.e. to trim a 5.0V module to 5.10V the
% value is 2).
Examples:
To trim down the output of a nominal 5.0V module
(HW004A0A) to 4.90V
% = 2
Rtrim-down = 249.39 k
To trim up the output of a nominal 3.3V module
(HW005A0F) to 3.63V
% = 10
Rtrim-up =94.2 k
Rtrim-down = - 6.11 k
511
%
Rtrim-down = - 4.46 k
346
%
Rtrim-down = - 4.90 k
390
%
Rtrim-up = - - 6.11 k
5.11VO(100+%)
1.225%
511
%
Rtrim-up = - - 4.46 k
5.11VO(100+%)
1.225%
346
%
Rtrim-up = - - 6.11 k
5.11x3.3(100+10)
1.225x10
511
10
Rtrim-down = - 6.11 k
511
2
Rtrim-up = - - 4.90 k
5.11VO(100+%)
1.225%
390
%
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 19
Feature Descriptions (continued)
Thermal Considerations
The power modules operate in a variety of thermal
environments; however, sufficient cooling should be
provided to help ensure reliable operation.
Considerations include ambient temperature, airflow,
module power dissipation, and the need for increased
reliability. A reduction in the operating temperature of the
module will result in an increase in reliability. The
thermal data presented here is based on physical
measurements taken in a wind tunnel.
The thermal reference point, Tref used in the
specifications is shown in Figure 66. For reliable
operation this temperature should not exceed 115 oC.
Figure 66. Tref Temperature Measurement
Location
Heat Transfer via Convection
Increased airflow over the module enhances the heat
transfer via convection. Derating figures showing the
maximum output current that can be delivered by each
module versus local ambient temperature (TA) for natural
convection and up to 3m/s (600 ft./min) are shown in the
respective Characteristics Curves section.
EMC Considerations
The figure 67 shows a suggested configuration to meet
the conducted emission limits of EN55022 Class B.
Vin+
HW005
Vin-
Vout+
Vout-
L1 - CMC
C6 56nF
C5 56nF
C1
0.68uF
C4
33uF
100V
C2
0.68uF
Pulse P0354
C3
0.68uF
L2
10uH
Notes: C1, C2, C3, C5 and C6 should be low impedance SMT
ceramics. C4 should be low impedance electrolytic (ESR<0.7
at 100kHz).
Figure 67. Suggested Configuration for EN55022
Class B
100K 500K 1M 5M 10M 30M
Frequency(Hz)
10
20
30
40
50
60
70
80
90
Level (dBµV)
EN 55022 Class B Conducted Average dBuV
Figure 68. EMC signature using above filter,
HW005A0F.
For further information on designing for EMC
compliance, please refer to the FLTR100V10 data sheet
(FDS01-043EPS).
Layout Considerations
The HW/HC005 power module series are low profile in
order to be used in fine pitch system card architectures.
As such, component clearance between the bottom of
the power module and the mounting board is limited.
Avoid placing copper areas on the outer layer directly
underneath the power module. Also avoid placing via
interconnects underneath the power module.
For additional layout guide-lines, refer to FLTR100V10
data sheet.
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
20 Tyco Electronics Power Systems
Mechanical Outline for HW/HC Surface-Mount Module
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm ( x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm ( x.xxx in ± 0.010 in.)
Top View
47.2
(1.860)
(1.162)
29.5
Side View
8.50
(0.335)
MAX
height
min stand-off
(0.100)
2.54
0.5
(.020)
max
compliance
Bottom View
Pin Function
1 Vout +
2 Vout -
Standard = No Pin
3 Optional = Vout +
9 Trim
11 On/Off
17 Vin -
18 Vin +
40.00
(1.576)
(0.394)
(1.031)
(0.065) (0.197)
(0.143) (1.379)
1.65
3.63
1239
11
17
18
PIN 3
OPTIONAL
35.00
5.00
26.16
10.00
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 21
Mechanical Outline for HW/HC Through-Hole Module
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm ( x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm ( x.xxx in ± 0.010 in.)
Top View
47.2
(1.860)
(1.162)
29.5
Side View
1.05
0.99
(0.041)
(0.039)
9.0
(0.35)
MIN
8.50
(0.335)
MAX
Bottom View
Pin Function
1 Vout +
2 Vout -
9 Trim
11 On/Off
17 Vin -
18 Vin +
1.65
3.63
129
11
1718
35.00
5.00
26.16
40.00
(1.576)
(1.031)
(0.065) (0.197)
(0.143) (1.379)
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
22 Tyco Electronics Power Systems
Recommended Pad Layout for Surface-Mount and Through-Hole Modules
Dimensions are in millimeters and (inches).
Tolerances: x.x mm ± 0.5 mm ( x.xx in. ± 0.02 in.) [unless otherwise indicated]
x.xx mm ± 0.25 mm ( x.xxx in ± 0.010 in.)
Pin Function
1 Vout +
2 Vout -
Standard = No Pin
3 Optional = Vout +
9 Trim
11 On/Off
17 Vin -
18 Vin +
47.2
29.5
18 17 11
9
3
2
1
1.65
3.63
10.00
26.16
IN 7 POSITIONS
PAD Ø 2.8mm
40.00
(1.860)
(1.576)
(1.379)
(0.394)
(0.197)
(0.143)
(0.065)
(1.162)
(1.031)
5.00
35.00
Surface Mount Pad Layout – Component side view
Pin Function
1 Vout +
2 Vout -
9 Trim
11 On/Off
17 Vin -
18 Vin +
47.2
29.5
18 17 11
9
2
1
1.65
3.63
26.16
IN 6 POSITIONS
40.00
(1.860)
(1.576)
(1.379)
(0.197)
(0.143)
(0.065)
(1.162)
(1.031)
5.00
35.00
PAD Ø4.0mm
HOLE Ø1.5mm
INSULATIVE
SPACER IN 3
POSITIONS
Through-Hole Pad Layout – Component side view
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 23
Packaging Details
The surface mount versions of the HW005 family are also available in tape & reel (suffix –SR) as an option. Detailed
of tape dimensions are shown below. Modules are shipped in quantities of 115 per reel.
Tape Dimensions
Dimensions are in millimeters and (inches).
40.00
(1.575)
4.00
(0.157)
(1.346)
34.20
PICK POINT
(2.692)
68.40
FEED
DIRECTION (2.834)
72.00
9.02
(0.355)
TOP COVER TAPE EMBOSSED CARRIER
NOTE: CONFORMS TO EAI-481 REV. A STANDARD
(2.692)
66.50
Reel Dimensions
Outside diameter: 330.2 mm (13.00”)
Inside diameter: 177.8 mm (7.00”)
Tape Width: 72.00 mm (2.834”)
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
24 Tyco Electronics Power Systems
Surface Mount Information
Packaging Details
The surface mount versions of the HW005 family
(suffix –S) are supplied as standard in the plastic tray
shown in Figure 69. The tray has external
dimensions of 136mm (W) x 322.6mm (L) x 18.4mm
(H) or 5.35in (W) x 12.7in (L) x 0.72in (H).
Figure 69. Surface Mount Packaging Tray
Tray Specification
Material Antistatic coated PVC
Max temperature 65oC
Max surface resistivity 1012/sq
Colour Clear
Capacity 15 power modules
Min order quantity 45 pcs (1box of 3 full trays)
Each tray contains a total of 15 power modules. The
trays are self-stacking and each shipping box will
contain 3 full trays plus one empty hold down tray
giving a total number of 45 power modules.
Surface mount versions of the HW005 family are also
available as an option packaged in Tape and Reel.
For further information on this please contact your
local Tyco Electronics Power Systems Technical
Sales Representative.
Pick and Place
The HW005-S series of DC-to-DC power converters
use an open-frame construction and are designed for
surface mount assembly within a fully automated
manufacturing process.
The HW005-S series modules are fitted with a Kapton
label designed to provide a large flat surface for pick
and placing. The label is located covering the Centre
of Gravity of the power module. The label meets all
the requirements for surface-mount processing, as
well as meeting UL safety agency standards. The
label will withstand reflow temperatures up to 300°C.
The label also carries product information such as
product code, date and location of manufacture.
24.2
14.7
COG
9.519.0
12.7
8.0
Note: All dimensions in mm.
Figure 70. Pick and Place Location
Z Plane Height
The ‘Z’ plane height of the pick and place label is
5.79mm nominal with an RSS tolerance of +/-0.25
mm.
Nozzle Recommendations
The module weight has been kept to a minimum by
using open frame construction. Even so, they have a
relatively large mass when compared with
conventional SMT components. Variables such as
nozzle size, tip style, vacuum pressure and placement
speed should be considered to optimize this process.
5.35 in
12.7 in
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 25
Surface Mount Information (cont)
The minimum recommended nozzle diameter for
reliable operation is 6mm. The maximum nozzle outer
diameter, which will safely fit within the allowable
component spacing, is 9 mm.
Oblong or oval nozzles up to 11 x 9 mm may also be
used within the space available.
For further information please contact your local Tyco
Electronics Power Systems Technical Sales
Representative.
Reflow Soldering Information
The HW005 family of power modules is available for
either Through-Hole (TH) or Surface Mount (SMT)
soldering. These power modules are large mass, low
thermal resistance devices and typically heat up
slower than other SMT components. It is
recommended that the customer review data sheets
in order to customize the solder reflow profile for each
application board assembly.
The following instructions must be observed when
SMT soldering these units. Failure to observe these
instructions may result in the failure of or cause
damage to the modules, and can adversely affect
long-term reliability.
The surface mountable modules in the HW005 family
use our newest SMT technology called “Column Pin”
(CP) connectors. Fig 71 shows the new CP connector
before and after reflow soldering onto the end-board
assembly.
HW005 Board
Insulator
Solder Ball
End assembly PCB
Figure 71. Column Pin Connector Before and After
Reflow Soldering
The CP is constructed from a solid copper pin with an
integral solder ball attached, which is composed of
tin/lead (Sn/Pb) solder. The CP connector design is
able to compensate for large amounts of co-planarity
and still ensure a reliable SMT solder joint.
Typically, the eutectic solder melts at 183oC, wets the
land, and subsequently wicks the device connection.
Sufficient time must be allowed to fuse the plating on
the connection to ensure a reliable solder joint. There
are several types of SMT reflow technologies
currently used in the industry. These surface mount
power modules can be reliably soldered using natural
forced convection, IR (radiant infrared), or a
combination of convection/IR. For reliable soldering
the solder reflow profile should be established by
accurately measuring the modules CP connector
temperatures.
REFLOW TEMP (°C)
0
50
10 0
15 0
200
250
300
Preheat zone
max 4
o
Cs
-1
Soak zone
30-240s
Heat zone
max 4
o
Cs
-1
Peak Temp 235
o
C
Coo ling
zo ne
1- 4
o
Cs
-1
T
lim
above
205
o
C
REFLOW TIME (S)
Figure 72. Recommended Reflow Profile
MAX TEMP SOLDER (°C)
200
205
210
215
220
225
230
235
240
0 102030405060
TIME LIMIT (S)
Figure 73. Time Limit Curve Above 205oC Reflow
Lead Free Soldering
The HW005 family of power modules are designed to
be used in a conventional Tin/Lead (Sn/Pd) solder
process where peak reflow temperatures are limited
to less than 235oC. Users who wish to assemble
these modules in a Lead Free solder process which, it
is expected, will require the use of higher peak reflow
temperatures should contact your local Tyco Power
Systems technical representative for more
information.
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
26 Tyco Electronics Power Systems
Solder Ball and Cleanliness
Requirements
The open frame (no case or potting) power module
will meet the solder ball requirements per
J-STD-001B. These requirements state that solder
balls must neither be loose nor violate the power
module minimum electrical spacing.
The cleanliness designator of the open frame power
module is C00 (per J specification).
Post Solder Cleaning and Drying
Considerations
Post solder cleaning is usually the final circuit-board
assembly process prior to electrical board testing. The
result of inadequate cleaning and drying can affect
both the reliability of a power module and the
testability of the finished circuit-board assembly. For
guidance on appropriate soldering, cleaning and
drying procedures, refer to Tyco Electronics Board
Mounted Power Modules: Soldering and Cleaning
Application Note (AP01-056EPS).
Data Sheet
Se
p
tember 29, 2003
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Tyco Electronics Power Systems 27
Ordering Information
Please contact your Tyco Electronics’ Sales Representative for pricing, availability and optional features.
Table 1. Device Codes
Input
Voltage
Output
Voltage
Output
Current
Remote
On/Off Logic
Connector
Type Product codes Comcodes
48 Vdc 5.0V 4A Negative SMT HW004A0A1-S 108960634
48 Vdc 5.0V 4A Negative SMT (tape & reel) HW004A0A1-SR 108985060
48 Vdc 3.3V 5A Negative SMT HW005A0F1-S 108960667
48 Vdc 3.3V 5A Negative SMT
HW005A0F1-S65* 108987512
48 Vdc 3.3V 5A Negative SMT (tape & reel) HW005A0F1-SR65* 108987488
48 Vdc 2.5V 6A Negative SMT HW006A0G1-S 108960774
48 Vdc 2.0V 6A Negative SMT HW006A0D1-S 108969676
48 Vdc 1.8V 6A Negative SMT HW006A0Y1-S 108960782
48 Vdc 1.5V 6A Negative SMT HW006A0M1-S 108963893
48 Vdc 1.2V 6A Negative SMT HW006A0P1-S 108963901
48 Vdc 1.0V 6A Negative SMT
HW006A0S1R01-S 108963927
48 Vdc 5.0V 4A Positive SMT HW004A0A-S 108968272
48 Vdc 3.3V 5A Positive SMT HW005A0F-S 108968678
48 Vdc 3.3V 5A Positive SMT (tape & reel) HW005A0F-SR 108984394
48 Vdc 3.3V 5A Positive SMT (tape & reel) HW005A0F-SR39* 108986951
48 Vdc 1.8V 6A Positive SMT HW006A0
-S 108974957
48 Vdc 5.0V 4A Negative Through-Hole HW004A0A1 108965476
48 Vdc 3.3V 5A Negative Through-Hole HW005A0F1 108967779
48 Vdc 5.0V 4A Negative SMT
HW004A0A1-SB 108980525
48 Vdc 5.0V 4A Negative SMT
HW004A0A31-S 108968975
48 Vdc 3.3V 5A Negative SMT HW005A0F31-S 108968967
24 Vdc 5.0V 4A Negative SMT HC004A0A1-S 108960642
24 Vdc 3.3V 5A Negative SMT HC005A0F1-S 108960659
48 Vdc 3.3V 5V
Nti
Negative SMT (tape&reel)
HW005A0F1-SR 108985052
48 Vdc 1.8V 6V Negative SMT (tape&reel)
HW006A0Y1-SR 108985078
*customer specific
Table 2. Device Options
Option Suffix
Negative remote on/off logic 1
With additional Vout+ pin3 3
Customer specific -39
Customer specific -65
Approved for Basic Insulation -B
Tape & Reel -R
Surface mount connections -S
HW/HC 4A – 6A Series Power Modules; dc-dc Converters
18
36 Vdc & 36
75 Vdc In
p
ut; 1.0Vdc to 5Vdc Out
p
ut
Data Sheet
Se
p
tember 29, 2003
World Wide Headquarters
Tyco Electronics Power Systems, Inc.
3000 Skyline Drive, Mesquite, TX 75149, USA
+1-800-843-1797
(Outside U.S.A.: +1-972-284-2626)
www.power.tycoelectronics.com
e-mail: techsupport1@tycoelectronics.com
Europe, Middle-East and Africa Headquarters
Tyco Electronics (UK) Ltd
Tel: +44 (0) 1344 469 300
Latin America, Brazil, Caribbean Headquarters
Tyco Electronics Power Systems
Tel: +56 2 209 8211
India Hea dquarte rs
Tyco Electronics Systems India Pte. Ltd.
Tel: +91 80 841 1633 x3001
Asia-Pacific Headquarters
Tyco Electronics Singapore Pte. Ltd.
Tel: +65 6416 4283
Tyco Electronics Corporation reserves the right to make changes to the product(s) or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
© 2003 Tyco Electronics Power Systems, Inc., (Mesquite, Texas) All International Rights Reserved.
Document No: DS03-017 ver.0.6
PDF No: hw-hc_4-6a