TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PNP SMALL SIGNAL SILICON TRANSISTOR Qualified per MIL-PRF-19500/511 DEVICES LEVELS 2N4261 2N4261UB 2N4261UBC * JAN JANTX JANTXV JANS * Available for JANS only ABSOLUTE MAXIMUM RATINGS (TC = +25C unless otherwise noted) Parameters / Test Conditions Symbol Value Unit Collector-Emitter Voltage VCEO 15 Vdc Collector-Base Voltage VCBO 15 Vdc Emitter-Base Voltage VEBO 4.5 Vdc IC 30 mAdc Collector Current Total Power Dissipation @ TA = +25C Operating & Storage Junction Temperature Range PT 0.2 W Top, Tstg -65 to +200 C TO-72 2N4261 Note: Consult 19500/511 for Thermal Performance Curves. ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise noted) Parameters / Test Conditions Symbol Min. Max. Unit 3 PIN OFF CHARACTERTICS Collector-Emitter Breakdown Voltage IC = 10mAdc 2N4261UB V(BR)CEO 15 Vdc Collector-Base Cutoff Current VCB = 15Vdc ICBO 10 Adc Emitter-Base Cutoff Current VEB = 4.5Vdc IEBO 10 Adc Collector-Emitter Cutoff Current VCE = 10Vdc, VBE = 0.4Vdc ICEX1 50 Adc Collector-Emitter Cutoff Current VCE = 10Vdc, VBE = 2.0Vdc ICEX2 5 Adc T4-LDS-0150 Rev. 2 (101161) 2N4261UBC (UBC = Ceramic Lid Version) Page 1 of 5 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 ELECTRICAL CHARACTERISTICS (TA = +25C, unless otherwise noted) Parameters / Test Conditions ON CHARACTERISTICS Symbol Min. Max. Unit (4) Forward-Current Transfer Ratio IC = 1.0mAdc, VCE = 1Vdc IC = 10mAdc, VCE = 1Vdc IC = 30mAdc, VCE = 1Vdc Collector-Emitter Saturation Voltage IC = 1mAdc, IB = 0.1mAdc IC = 10mAdc, IB = 1.0mAdc Base-Emitter Saturation Voltage (Non-Saturated) VCE = 1Vdc, IC = 1mAdc VCE = 1Vdc, IC = 10mAdc 25 hFE 30 20 VCE(sat) 150 0.15 0.35 Vdc VBE 0.6 0.80 1.0 Vdc Max. Unit DYNAMIC CHARACTERISTICS Parameters / Test Conditions Symbol Min. Magnitude of Small-Signal Forward Current Transfer Ratio IC = 10mAdc, VCE = 10Vdc, f = 100MHz |hfe| 20 Output Capacitance VCB = 4Vdc, IE = 0, 100kHz f 1.0MHz Cobo 2.5 pF Input Capacitance VEB = 0.5Vdc, IC = 0, 100kHz f 1.0MHz Cibo 2.5 pF Max. Unit SWITCHING CHARACTERISTICS Parameters / Test Conditions Symbol Min. Turn-On Time VCC = 17Vdc; IC = 10mAdc ton 2.5 s Turn-Off Time VCC = 17Vdc; IC = 10mAdc toff 3.5 s (4) Pulse Test: Pulse Width = 300s, Duty Cycle 2.0%. T4-LDS-0150 Rev. 2 (101161) Page 2 of 5 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 PACKAGE DIMENSIONS Symbol CD CH HD LC LD LL LU L1 L2 P Q TL TW r Dimensions Inches Millimeters Min Max Min Max .178 .195 4.52 4.95 .170 .210 4.32 5.33 .209 .230 5.31 5.84 .100 TP 2.54 TP .016 .021 .406 .533 .500 .750 12.70 19.05 .016 .019 .41 .48 .050 1.27 .250 6.35 .100 2.54 .040 1.02 .028 .048 .71 1.22 .036 .046 .91 1.17 .007 .18 45 TP Notes 5 5 7, 8 7, 8 7, 8 5 NOTES: 1 Dimension are in inches. 2 Millimeters are given for general information only. 3 Beyond r (radius) maximum, TH shall be held for a minimum length of .011 (0.28 mm). 4 Dimension TL measured from maximum HD. 5 Body contour optional within zone defined by HD, CD, and Q. 6 Leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. 7 Dimension LU applies between L1 and L2. Dimension LD applies between L2 and LL minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 8 All four leads. 9 Dimension r (radius) applies to both inside corners of tab. 10 In accordance with ASME Y14.5M, diameters are equivalent to x symbology. 11 Lead 1 = emitter, lead 2 = base, lead 3 = collector, lead 4 = case (electrically connected). FIGURE 1. Physical dimensions for 2N4261 (TO-72). T4-LDS-0150 Rev. 2 (101161) Page 3 of 5 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Ltr. BH BL BW CL CW LL1 LL2 Dimensions Inches Millimeters Min Max Min Max .046 .056 1.17 1.42 .115 .128 2.92 3.25 .085 .108 2.16 2.74 .128 3.25 .108 2.74 .022 .038 0.56 0.96 .017 .035 0.43 0.89 Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Note Ltr. LS1 LS2 LW r r1 r2 Dimensions Inches Millimeters Min Max Min Max .035 .040 0.89 1.02 .071 .079 1.80 2.01 .016 .024 0.41 0.61 .008 0.20 .012 0.31 .022 0.56 Note NOTES: 1 Dimensions are in inches. 2 Millimeters are given for general information only. 3 Pad 1 = Base, Pad 2 = Emitter, Pad 3 = Collector, Pad 4 = Shielding connected to the lid. 4 In accordance with ASME Y14.5M, diameters are equivalent to x symbology. FIGURE 2. Physical dimensions for 2N4261UB, surface mount. T4-LDS-0150 Rev. 2 (101161) Page 4 of 5 TECHNICAL DATA SHEET 6 Lake Street, Lawrence, MA 01841 1-800-446-1158 / (978) 620-2600 / Fax: (978) 689-0803 Website: http: //www.microsemi.com Ltr. BH BL BW CL CW LL1 LL2 Dimensions Inches Millimeters Min Max Min Max .046 .071 1.17 1.80 .115 .128 2.29 3.25 .085 .108 2.16 2.74 .128 3.25 .108 2.74 .022 .038 0.56 0.96 .017 .035 0.43 0.89 Gort Road Business Park, Ennis, Co. Clare, Ireland Tel: +353 (0) 65 6840044 Fax: +353 (0) 65 6822298 Note Ltr. LS1 LS2 LW r r1 r2 Dimensions Inches Millimeters Min Max Min Max .036 .040 0.91 1.02 .071 .079 1.81 2.01 .016 .024 0.41 0.61 .008 .203 .012 .305 .022 .559 Note NOTES: 1 2 3 4 5 Dimensions are in inches. Millimeters are given for general information only. Hatched areas on package denote metallized areas Pad 1 = Base, Pad 2 = Emitter, Pad 3 = Collector, Pad 4 = connected to the lid braze ring. In accordance with ASME Y14.5M, diameters are equivalent to x symbology. * FIGURE 3. Physical dimensions, surface mount (UBC version, ceramic lid). T4-LDS-0150 Rev. 2 (101161) Page 5 of 5