Not Recommended for New Designs SFH610A, SFH6106 www.vishay.com Vishay Semiconductors Optocoupler, Phototransistor Output, High Reliability, 5300 VRMS FEATURES SFH610A 1 4 E C 2 3 C A * Good CTR linearity depending on forward current * Isolation test voltage, 5300 VRMS * High collector emitter voltage, VCEO = 70 V * Low saturation voltage * Fast switching times * Low CTR degradation * Temperature stable * Low coupling capacitance * End stackable, 0.100" (2.54 mm) spacing * High common mode interference immunity SFH6106 A 1 4 E * Lead (Pb)-free component C 2 3 C * Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 i179056 DESCRIPTION The SFH610A (DIP) and SFH6106 (SMD) feature a high current transfer ratio, low coupling capacitance and high isolation voltage. These couplers have a GaAs infrared diode emitter, which is optically coupled to a silicon planar phototransistor detector, and is incorporated in a plastic DIP-4 or SMD package. The coupling devices are designed for signal transmission between two electrically separated circuits. The couplers are end-stackable with 2.54 mm spacing. Creepage and clearance distances of > 8.0 mm are achieved with option 6. This version complies with IEC 60950 (DIN VDE 0805) for reinforced insulation up to an operation voltage of 400 VRMS or DC. Specifications subject to change. AGENCY APPROVALS * UL1577, file no. E52744 system code H or J, double protection * DIN EN 60747-5-5 (VDE 0884) available with option 1 * CSA 93751 * BSI IEC 60950; IEC 60065 ORDERING INFORMATION PART SFH610A-1 SFH610A-2 SFH610A-3 SFH610A-4 SFH610A-5 SFH6106-1 SFH6106-2 SFH6106-3 SFH6106-4 SFH6106-5T SFH610A-1X006 SFH610A-1X018T SFH610A-2X006 SFH610A-3X006 SFH610A-3X007 SFH610A-4X006 REMARKS CTR 40 % to 80 %, DIP-4 CTR 63 % to 125 %, DIP-4 CTR 100 % to 200 %, DIP-4 CTR 160 % to 320 %, DIP-4 CTR 250 % to 500 %, DIP-4 CTR 40 % to 80 %, SMD-4 CTR 63 % to 125 %, SMD-4 CTR 100 % to 200 %, SMD-4 CTR 160 % to 320 %, SMD-4 CTR 250 % to 500 %, SMD-4, tape and reel CTR 40 % to 80 %, DIP-4 400 mil CTR 40 % to 80 %, SMD-4 400 mil, wide leadspread CTR 63 % to 125 %, DIP-4 400 mil CTR 100 % to 200 %, DIP-4 400 mil CTR 100 % to 200 %, SMD-4 CTR 160 % to 320 %, DIP-4 400 mil Note * For additional information on the available options refer to option information. Rev. 2.1, 14-Jan-13 Document Number: 83666 1 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs SFH610A, SFH6106 www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL VALUE UNIT VR IF IFSM Pdiss 6 60 2.5 100 V mA A mW VCE VEC IC IC Pdiss 70 7 50 100 150 V V mA mA mW VISO 5300 VRMS 7 7 mm mm 0.4 mm INPUT Reverse voltage DC forward current Surge forward current Power dissipation OUTPUT Collector emitter voltage Emitter collector voltage Collector current t 10 s tp 1.0 ms Power dissipation COUPLER Isolation test voltage between emitter and detector Creepage distance Clearance distance Insulation thickness between emitter and detector Comparative tracking index per DIN IEC112/VDE 0303 part 1 Isolation resistance 175 VIO = 500 V, Tamb = 25 C VIO = 500 V, Tamb = 100 C Storage temperature range Ambient temperature range Soldering temperature (1) max. 10 s, dip soldering distance to seating plane 1.5 mm RIO RIO Tstg Tamb 1012 1011 - 55 to + 150 - 55 to + 100 C C Tsld 260 C Notes * Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliability. (1) Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through hole devices (DIP). ELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT INPUT Forward voltage IF = 60 mA VF 1.25 1.65 V Reverse current VR = 6 V IR 0.01 10 A Capacitance VR = 0 V, f = 1 MHz Thermal resistance CO 13 pF Rthja 750 K/W OUTPUT Collector emitter capacitance VCE = 5 V, f = 1 MHz CCE 5.2 pF Rthja 500 K/W SFH610A-1 ICEO 2 50 nA SFH6106-1 ICEO 2 50 nA SFH610A-2 ICEO 2 50 nA SFH6106-2 ICEO 2 50 nA SFH610A-3 ICEO 5 100 nA SFH6106-3 ICEO 5 100 nA SFH610A-4 ICEO 5 100 nA SFH6106-4 ICEO 5 100 nA SFH610A-5 ICEO 5 100 nA SFH6106-5T ICEO 5 100 nA Thermal resistance Collector emitter leakage current Rev. 2.1, 14-Jan-13 VCE = 10 V Document Number: 83666 2 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs SFH610A, SFH6106 www.vishay.com Vishay Semiconductors ELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT 0.4 V COUPLER Collector emitter saturation voltage IF = 10 mA, IC = 2.5 mA VCEsat 0.25 f = 1 MHz CC 0.4 Coupling capacitance pF Note * Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements. CURRENT TRANSFER RATIO PARAMETER TEST CONDITION IF = 10 mA, VCE = 5.0 V IC/IF IF = 1 mA, VCE = 5 V PART SYMBOL MIN. TYP. MAX. UNIT SFH610A-1 CTR 40 80 % SFH6106-1 CTR 40 80 % SFH610A-2 CTR 63 125 % SFH6106-2 CTR 63 125 % SFH610A-3 CTR 100 200 % SFH6106-3 CTR 100 200 % SFH610A-4 CTR 160 320 % SFH6106-4 CTR 160 320 % SFH610A-5 CTR 250 500 % SFH6106-5T CTR 250 500 % SFH610A-1 CTR 13 30 % SFH6106-1 CTR 13 30 % SFH610A-2 CTR 22 45 % SFH6106-2 CTR 22 45 % SFH610A-3 CTR 34 70 % SFH6106-3 CTR 34 70 % SFH610A-4 CTR 56 90 % SFH6106-4 CTR 56 90 % MIN. TYP. SWITCHING CHARACTERISTICS PARAMETER TEST CONDITION PART SYMBOL MAX. UNIT NON-SATURATED Current VCC = 5 V, RL = 75 IF 10 mA Rise time VCC = 5 V, RL = 75 tr 2 s Fall time VCC = 5 V, RL = 75 tf 2 s Turn-on time VCC = 5 V, RL = 75 ton 3 s Turn-off time VCC = 5 V, RL = 75 toff 2.3 s VCC = 5 V FCO 250 kHz IF 20 mA IF 10 mA IF 10 mA IF 5 mA Cut-off frequency SATURATED SFH610A-1 SFH6106-1 SFH610A-2 Current SFH6106-2 SFH610A-3 SFH6106-3 SFH610A-4 SFH6106-4 Rev. 2.1, 14-Jan-13 Document Number: 83666 3 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs SFH610A, SFH6106 www.vishay.com Vishay Semiconductors SWITCHING CHARACTERISTICS PARAMETER TEST CONDITION PART SYMBOL MIN. TYP. MAX. UNIT SATURATED SFH610A-1 SFH6106-1 SFH610A-2 Rise time SFH6106-2 SFH610A-3 SFH6106-3 SFH610A-4 SFH6106-4 SFH610A-1 SFH6106-1 SFH610A-2 Fall time SFH6106-2 SFH610A-3 SFH6106-3 SFH610A-4 SFH6106-4 SFH610A-1 SFH6106-1 SFH610A-2 Turn-on time SFH6106-2 SFH610A-3 SFH6106-3 SFH610A-4 SFH6106-4 SFH610A-1 SFH6106-1 SFH610A-2 Turn-off time SFH6106-2 SFH610A-3 SFH6106-3 SFH610A-4 SFH6106-4 tr 2 s tr 3 s tr 3 s tr 4 s tf 11 s tf 14 s tf 14 s tf 15 s ton 3 s ton 4.2 s ton 4.2 s ton 6 s toff 18 s toff 23 s toff 23 s toff 25 s Note * All values presented are typical values. Rev. 2.1, 14-Jan-13 Document Number: 83666 4 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs SFH610A, SFH6106 www.vishay.com Vishay Semiconductors SAFETY AND INSULATIO RATINGS PARAMETER TEST CONDITION SYMBOL MIN. Climatic classification (according to IEC 68 part 1) TYP. MAX. UNIT 55/100/21 Comparative tracking index CTI 175 VIOTM 10000 VIORM 890 399 V V PSO 400 mW ISI 275 mA TSI 175 C Creepage distance standard DIP-4 7 mm Clearance distance standard DIP-4 7 mm Creepage distance 400 mil DIP-4 8 mm Clearance distance 400 mil DIP-4 8 mm per IEC 60950 2.10.5.1 0.4 mm Insulation thickness, reinforced rated Note * As per IEC 60747-5-2, 7.4.3.8.1, this optocoupler is suitable for "safe electrical insulation" only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuits. TYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified) 1. 0 k IF R L = 75 IF VCC = 5 V VCC = 5 V IC 47 47 isfh610a_02 isfh610a_01 Fig. 1 - Linear Operation (without saturation) % 103 IC IF 5 Fig. 3 - Switching Operation (with saturation) 30 Ic mA IF = 10 mA, VCC = 5.0 V IF = 14 mA 4 IF = 12 mA 20 3 2 102 IF = 10 mA IF = 8 mA 1 5 IF = 6 mA 10 IF = 4 mA IF = 1 mA 101 - 25 0 25 50 75 TA (C) isfh610a_03 Fig. 2 - Current Transfer Ratio (CTR) vs. Temperature Rev. 2.1, 14-Jan-13 0 0 isfh610a_04 5 IF = 2 mA 10 V VCE 15 Fig. 4 - Output Characteristics (typ.) Collector Current vs. Collector Emitter Voltage Document Number: 83666 5 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs SFH610A, SFH6106 www.vishay.com Vishay Semiconductors 1.2 VF VF = f (IF) V IF 25 C 50 C 75 C 120 mA Ptot = f (TA) 90 1.1 60 1.0 30 0.9 10-1 5 100 101 5 isfh610a_05 102 5 mA IF 20 C 0 25 50 75 isfh610a_08 Fig. 5 - Diode Forward Voltage vs. Forward Current pF 0 TA C 100 Fig. 8 - Permissible Power Dissipation vs. Temperature 200 Ptot mW f = 1.0 MHz 15 150 10 100 5 50 Transistor Diode CCE 0 10-2 10-1 100 101 102 V Ve isfh610a_06 104 mA 5 103 5 D=0 0.005 0.01 0.02 D= tp T 0.05 0.1 0 isfh610a_09 Fig. 6 - Transistor Capacitance (typ.) vs. Collector Emitter Voltage IF 0 tp 25 50 75 TA C 100 Fig. 9 - Permissible Diode Forward Current vs. Ambient Temperature I F T Pulse cycle D = parameter 0.2 102 5 101 0.5 DC 10-5 isfh610a_07 10-4 10-3 10-2 10-1 100 s 101 tp Fig. 7 - Permissible Pulse Handling Capability Forward Current vs. Pulse Width Rev. 2.1, 14-Jan-13 Document Number: 83666 6 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs SFH610A, SFH6106 www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in inches (millimeters) 6.81 6.48 Pin 1 identification 4.83 4.55 7.62 typ. ISO Method A 10 0.84 0.74 1.14 0.76 3.81 3.30 4 typ . 6.35 5.84) 3.30 2.79 0.89 0.51 0 to 15 1.32 1.22 0.25 typ. 2.67 2.41 i178027-1 SMD 0.268 (6.81) 0.255 (6.48) 0.190 (4.83) 0.179 (4.55) PIN 1 IDENTIFICATION 0.030 (0.76) 0.100 (2.54) R 0.010 (0.25) 0.070 (1.78) 0.315 (8.00) mi n. 0.435 (11.05) 0.045 (1.14) 0.030 (0.76) 0.060 (1.52) 0.395 (10.03) 0.375 (9.53) 0.312 (7.92) 0.296 (7.52) 0.033 (0.84) 0.029 (0.74) 10 0.150 (3.81) 0.130 (3.30) 0.010 (0.25) 0.008 (0.20) ISO method A 4 typ. 0.052 (1.32) 0.048 (1.22) i17802 9-2 Rev. 2.1, 14-Jan-13 0.098 (0.249) 0.040 (0.102) Lead coplanarity 0.004 (0.102) max. ('K') 0.105 (2.67) 0.095 (2.41) Document Number: 83666 7 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Not Recommended for New Designs SFH610A, SFH6106 www.vishay.com Vishay Semiconductors Option 6 Option 7 0.407 (10.36) 0.391 (9.96) 0.307 (7.8) 0.291 (7.4) 0.300 (7.62) typ. 0.028 (0.7) 0.400 (10.16) 0.430 (10.92) Rev. 2.1, 14-Jan-13 0.300 (7.62) typ. 0.180 (4.6) 0.160 (4.1) 0.315 (8.0) min. 0.014 (0.35) 0.010 (0.25) Option 8 0.331 (8.4) min. 0.406 (10.3) max. 0.020 (0.50) 0.000 (0.00) 0.150 (3.81) 0.130 (3.30) 0.365 (9.27) min. 0.472 (12.00) max. 18487 Document Number: 83666 8 For technical questions, contact: optocoupleranswers@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000