TPS2062A TPS2066A www.ti.com ........................................................................................................................................... SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 TWO CHANNEL, CURRENT-LIMITED, POWER-DISTRIBUTION SWITCHES FEATURES APPLICATIONS * * * * * * 1 2 * * * * * * * * * * 70-m High-Side MOSFET 1-A Continuous Current Thermal and Short-Circuit Protection Accurate Current-Limit (1.2 A min, 2 A max) Operating Range: 2.7 V to 5.5 V 0.6-ms Typical Rise Time Undervoltage Lockout Deglitched Fault Report (OCx) No OCx Glitch During Power Up 1-A Maximum Standby Supply Current Bidirectional Switch Ambient Temperature Range: -40C to 85C Built-in Soft-Start UL Listed -- File No. E169910, Both Single and Ganged Channel Configuration Heavy Capacitive Loads Short-Circuit Protection TPS2062A/TPS2066A D PACKAGE (TOP VIEW) 8 7 6 5 1 2 3 4 GND IN EN1 EN2 OC1 OUT 1 OUT2 OC2 TPS2062A/TPS2066A DRB PACKAGE (TOP VIEW) GND IN EN1 EN2 1 2 3 4 PAD 8 7 6 5 OC1 OUT1 OUT2 OC2 Enable inputs are active low for all TPS2062A and active high for all TPS2066A DESCRIPTION The TPS206xA power-distribution switches are intended for applications where heavy capacitive loads and short-circuits are likely to be encountered. The TPS206xA family is pin-for-pin compatible with the TPS206x family with a tighter overcurrent tolerance. This family of devices incorporates two 70-m N-channel MOSFET power switches for power-distribution systems that require multiple power switches in a single package. Each switch is controlled by a logic enable input. Gate drive is provided by an internal charge pump designed to control the power-switch rise and fall times to minimize current surges during switching. The charge pump requires no external components and allows operation from supplies as low as 2.7 V. Each device limits the output current to a safe level by switching into a constant-current mode when the output load exceeds the current-limit threshold or a short is present. Individual channels indicate the presence of an overcurrent condition by asserting its corresponding OCx output (active low). Thermal protection circuitry disables the device during overcurrent or short-circuit events to prevent permanent damage. The device recovers from thermal shutdown automatically once the device has cooled sufficiently. The device provides undervoltage lockout to disable the device until the input voltage rises above 2.0 V. The TPS206xA is designed to current limit at 1.6 A typically per channel. TPS201xA TPS202x TPS203x 0.2 A - 2 A 0.2 A - 2 A 0.2 A - 2 A TPS2014 TPS2015 TPS2041B TPS2051B TPS2045A TPS2049 TPS2055A TPS2061 TPS2065 TPS2068 TPS2069 600 mA 1A 500 mA 500 mA 250 mA 100 mA 250 mA 1A 1A 1.5 A 1.5 A 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2008, Texas Instruments Incorporated TPS2062A TPS2066A SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 ........................................................................................................................................... www.ti.com This device contains circuits to protect its inputs and outputs against damage due to high static voltages or electrostatic fields. These circuits have been qualified to protect this device against electrostatic discharges (ESD) of up to 2 kV according to MIL-STD-883C, Method 3015; however, it is advised that precautions be taken to avoid application of any voltage higher than maximum-rated voltages to these high-impedance circuits. During storage or handling the device leads should be shorted together or the device should be placed in conductive foam. In a circuit, unused inputs should always be connected to an appropriate logic voltage level, preferably either VCC or ground. Specific guidelines for handling devices of this type are contained in the publication Guidelines for Handling Electrostatic-Discharge-Sensitive (ESDS) Devices and Assemblies available from Texas Instruments. AVAILABLE OPTION AND ORDERING INFORMATION TA ENABLE (1) TYPICAL SHORT-CIRCUIT LIMIT 1A 1.6 A Active low -40C to 85C PACKAGE (1) RECOMMENDED MAXIMUM CONTINUOUS LOAD CURRENT Active high D-8 (SOIC) DRB-8 (SON) PART # STATUS PART # STATUS TPS2062AD AVAILABLE TPS2062ADRB AVAILABLE TPS2066AD AVAILABLE TPS2066ADRB AVAILABLE For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. ABSOLUTE MAXIMUM RATINGS over operating temperature range unless otherwise noted (1) (2) VALUE UNIT VI Input voltage range IN -0.3 to 6 V VO Output voltage range OUTx -0.3 to 6 V Input voltage range ENx, ENx -0.3 to 6 V Voltage range OCx -0.3 to 6 V Continuous output current OUTx VI IO Internally limited Continuous total power dissipation See "Dissipation Rating Table" TJ Operating junction temperature range -40 to 125 Tstg Storage temperature range -65 to 150 C 2 kV 500 V ESD (1) (2) Human body model MIL-STD-883C Electrostatic discharge protection Charge device model (CDM) C Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to GND. DISSIPATION RATING TABLE PACKAGE Low-K (1) D-8 170 C/W High-K (2) D-8 97.5 C/W Low-K (3) High-K (5) (1) (2) (3) (4) (5) 2 THERMAL RESISTANCE JA BOARD DRB (4) DRB (4) TA 25C POWER RATING DERATING FACTOR ABOVE TA = 25C TA = 70C POWER RATING TA = 85C POWER RATING 586 mW 5.86 mW/C 320 mW 234 mW 1025 mW 10.26 mW/C 564 mW 410 mW 270 C/W 370 mW 3.71 mW/C 203 mW 148 mW 60 C/W 1600 mW 16.67 mW/C 916 mW 666 mW The JEDEC low-K (1s) board used to dervie this data was a 3in x 3in, two-layer board with 2-ounce copper traces on top of the board. The JEDEC high-K (2s2p) board used to dervive this data was a 3in x 3in, multilayer board with 1-ounce internal power and ground planes and 2-ounce copper traces on top and bottom of the board. Soldered PowerPAD on a standard 2-layer PCB without vias for thermal pad. See TI application note SLMA002 for further details. See Recommended Operating Conditions Table for PowePad connection guidelines to meet qualifying conditions for CB Certificate Soldered PowerPAD on a standard 4-layer PCB with vias for thermal pad. See TI application note SLMA002 for further details. Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A TPS2062A TPS2066A www.ti.com ........................................................................................................................................... SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 RECOMMENDED OPERATING CONDITIONS (1) Input voltage, IN MIN MAX UNIT 2.7 5.5 V Input voltage, ENx, ENx 0 5.5 V IO Continuous output current, OUTx 0 1 A TJ Operating virtual junction temperature -40 125 C VI (1) The PowePad must be connected externally to GND pin to meet qualifying conditions for CB Certificate (DRB package only) ELECTRICAL CHARACTERISTICS over recommended operating junction temperature range, VI = 5.5 V, IO = 1 A, V/ENx = 0 V (TPS2062A) or VENx = 5.5 V (unless otherwise noted) TEST CONDITIONS (1) PARAMETER MIN TYP MAX 70 100 UNIT POWER SWITCH rDS(on) Static drain-source on-state resistance 2.7 V VI 5.5 V, IO = 1 A tr Rise time, output tf Fall time, output TJ = 25C -40C TJ 125C 135 VI = 5.5 V VI = 2.7 V VI = 5.5 V 0.6 0.4 CL = 1 F, RL = 5 , TJ = 25C VI = 2.7 V m 1.5 1 0.05 0.5 0.05 0.5 ms ENABLE INPUT EN OR EN VIH High-level input voltage VIL Low-level input voltage II Input current ton Turnon time toff Turnoff time 2 2.7 V VI 5.5 V 0.8 -0.5 0.5 3 CL = 100 F, RL = 5 3 V A ms CURRENT LIMIT IOS Short-circuit output current per channel VI = 5 V, OUTx connected to GND, device enabled into short-circuit IOC Overcurrent trip threshold VIN = 5 V IOS_G Ganged short-circuit output current VI = 5 V, OUT1 & OUT2 connected to GND, device enabled into short-circuit IOC_G Ganged overcurrent trip threshold VI = 5 V, OUT1 & OUT2 tied together TJ = 25C 1.2 1.6 2.0 -40C TJ 125C 1.1 1.6 2.1 IOS 2.1 2.45 TJ = 25C 2.4 3.2 4.0 2.2 3.2 4.2 IOS_G 4.2 4.9 TJ = 25C 0.5 1 -40C TJ 125C 0.5 5 TJ = 25C 50 60 -40C TJ 125C 50 75 -40C TJ 125C A A A SUPPLY CURRENT IIL Supply current, device disabled No load on OUT IIH Supply current, device enabled No load on OUT Ilkg Leakage current, device disabled OUT connected to ground -40C TJ 125C VO = 5.5 V, VI = 0 V TJ = 25C Reverse leakage current A A 1 A 0.2 A UNDERVOLTAGE LOCKOUT Low-level input voltage, IN VI rising Hysteresis, IN VI falling 2 2.5 75 V mV OVERCURRENT FLAG VOL Output low voltage, OC I/OCx = 5 mA Off-state current V/OCx = 5.0 V or 3.3 V OC deglitch OCx assertion or de-assertion 4 8 0.4 V 1 A 15 ms THERMAL SHUTDOWN (2) Thermal shutdown threshold 135 Recovery from thermal shutdown 125 Hysteresis (1) (2) C C 10 C Pulsed load testing used to maintain junction temperature close to ambient The thermal shutdown only reacts under overcurrent conditions. Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A 3 TPS2062A TPS2066A SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 ........................................................................................................................................... www.ti.com DEVICE INFORMATION Terminal Functions TERMINAL NAME I/O DESCRIPTION TPS2062A TPS2066A EN1 3 -- I Enable input, logic low turns on power switch IN-OUT1 EN2 4 -- I Enable input, logic low turns on power switch IN-OUT2 EN1 -- 3 I Enable input, logic high turns on power switch IN-OUT1 EN2 -- 4 I Enable input, logic high turns on power switch IN-OUT2 GND 1 1 IN 2 2 I Input voltage OC1 8 8 O Channel 1 over-current indicator; the output is open-drain, active low type OC2 5 5 O Channel 2 over-current indicator; the output is open-drain, active low type OUT1 7 7 O Power-switch output, IN-OUT1 OUT2 6 6 O Power-switch output, IN-OUT2 PAD PAD PowerPADTM (1) (1) Ground Connect PowerPAD to GND for proper operation (DRB package only) See the Recommended Operating Conditions Table for PowePad connection guidelines to meet qualifying conditions for CB Certificate. FUNCTIONAL BLOCK DIAGRAM FAULT 1 Thermal Sense GND Deglitch EN1 Driver Current Limit Charge Pump CS OUT1 Current Sense UVLO CS IN OUT2 Charge Pump EN2 Driver Current Limit FAULT 2 Deglitch Thermal Sense 4 A. Current sense B. Active low (ENx) for TPS2062A. Active high (ENx) for TPS2066A. Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A TPS2062A TPS2066A www.ti.com ........................................................................................................................................... SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 PARAMETER MEASUREMENT INFORMATION OUT RL CL tr tf V OUT 90% 90% 10% 10% TEST CIRCUIT V EN 50% 50% ton 50% 50% V EN toff toff ton 90% 90% V OUT V OUT 10% 10% VOLTAGE WAVEFORMS Figure 1. Test Circuit and Voltage Waveforms RL = 5W, CL = 1mF, TA = 25C VI(EN) 5 V/div VI(EN) 5 V/div RL = 5W , CL = 1 mF TA = 25C VO(OUT) 2 V/div VO(OUT) 2 V/div t - Time - 500 ms/div t - Time - 500 ms/div Figure 2. Turnon Delay and Rise Time With 1-F Load Figure 3. Turnoff Delay and Fall Time With 1-F Load Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A 5 TPS2062A TPS2066A SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 ........................................................................................................................................... www.ti.com PARAMETER MEASUREMENT INFORMATION (continued) RL = 5W, CL = 100 mF, TA = 25C VI(EN) 5 V/div VI(EN) 5 V/div RL = 5W, VO(OUT) 2 V/div CL = 100 mF, TA = 25C VO(OUT) 2 V/div t - Time - 500 ms/div t - Time - 500 ms/div Figure 4. Turnon Delay and Rise Time With 100-F Load VI(EN) 5 V/div Figure 5. Turnoff Delay and Fall Time With 100-F Load VIN = 5 V, RL = 5W , TA = 25C VI(EN) 5 V/div 220 mF 470 mF IO(OUT) 500 mA/div IO(OUT) 500 mA/div 100 mF t - Time - 500 ms/div Figure 6. Short-Circuit Current, Device Enabled Into Short 6 t - Time - 1 ms/div Figure 7. Inrush Current With Different Load Capacitance Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A TPS2062A TPS2066A www.ti.com ........................................................................................................................................... SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 PARAMETER MEASUREMENT INFORMATION (continued) VO(OC) 2 V/div VO(OC) 2 V/div IO(OUT) 1 A/div IO(OUT) 1 A/div t - Time - 2 ms/div t - Time - 2 ms/div Figure 8. 2- Load Connected to Enabled Device Figure 9. 1- Load Connected to Enabled Device POWER-SUPPLY CONSIDERATIONS TPS2062A 2 Power Supply 2.7 V to 5.5 V IN OUT1 0.1 mF 8 3 5 4 7 Load 0.1 mF 22 mF 0.1 mF 22 mF OC1 EN1 OUT2 6 OC2 Load EN2 GND 1 Figure 10. Typical Application DETAILED DESCRIPTION OVERVIEW The devices are current-limited, power distribution switches using N-channel MOSFETs for applications where short-circuits or heavy capacitive loads will be encountered. These devices have a minimum fixed current-limit threshold above 1.1 A allowing for continuous operation up to 1 A per channel. Overtemperature protection is an addtional device shutdown feature. Each device incorporates an internal charge pump and gate drive circuitry necessary to drive the N-channel MOSFETs. The charge pump supplies power to the driver circuit and provides the necessary voltage to pull the gate of the MOSFET above the source. The charge pump operates from input voltages as low as 2.7 V and requires little supply current. The driver controls the gate voltage of the power switch. The driver incorporates circuitry that controls the rise and fall times of the output voltage to provide "soft-start" and to limit large current and voltage surges. Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A 7 TPS2062A TPS2066A SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 ........................................................................................................................................... www.ti.com OVERCURRENT When an overcurrent condition is detected, the device maintains a constant output current and reduces the output voltage accordingly. Three possible overload conditions can occur. In the first condition, the output has been shorted before the device is enabled or before voltage is applied to IN. The device senses the short and immediately switches into a constant-current output. In the second condition, a short or an overload occurs while the device is enabled. At the instant the overload occurs, high currents may flow for several microseconds before the current-limit circuit can react. The device operates in constant-current mode after the current-limit circuit has responded. In the third condition, the load is increased gradually beyond the recommended operating current. The current is permitted to rise until the current-limit threshold is reached. The devices are capable of delivering current up to the current-limit threshold without damage. Once the threshold is reached, the device switches into constant-current mode. Complete shutdown occurs only if the fault is present long enough to activate thermal limiting. The device will remain off until the junction temperature cools approximately 10C and will then re-start. The device will continue to cycle on/off until the overcurrent condition is removed. OCx RESPONSE Each OCx open-drain output is asserted (active low) during an overcurrent or overtemperature condition on that channel. The output remains asserted until the fault condition is removed. The TPS206xA eliminates false OCx reporting by using internal delay circuitry after entering or leaving an overcurrent condition. This "deglitch" time is approximately 8-ms. This ensures that OCx is not accidentally asserted due to normal operation such as starting into a heavy capacitive load. Overtemperature conditions are not deglitched and assert and de-assert the OCx signal immediately. UNDERVOLTAGE LOCKOUT (UVLO) The undervoltage lockout (UVLO) circuit disables the power switch until the input voltage reaches the UVLO turn-on threshold. Built-in hysteresis prevents unwanted on/off cycling due to input voltage drop from large current surges. Enable (ENx or ENx) The logic enable controls the power switch, bias for the charge pump, driver, and other circuits to reduce the supply current. The supply current is reduced to less than 5 A when a logic high is present on ENx, or when a logic low is present on ENx. A logic low input on ENx or a logic high input on ENx enables the driver, control circuits, and power switch for that channel. THERMAL SENSE The TPS206xA monitors the operating temperature of both power distribution switches with individual thermal sensors. The junction temperature of each channel rises during an overcurrent or short-circuit condition. When the die temperature of a particular channel rises above a minimum of 135C in an overcurrent condition, the internal thermal sense circuitry disables the individual channel in overtemperature to prevent damage. Hysteresis is built into the thermal sensor and re-enables the power switch individually after it has cooled approximately 10C. The power switch cycles on and off until the fault is removed. This topology allows one channel to continue normal operation even if the other channel is in an overtemperature condition. The open-drain overcurrent flag (OCx) is asserted (active low) corresponding to the channel that is in an overtemperature or overcurrent condition. 8 Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A TPS2062A TPS2066A www.ti.com ........................................................................................................................................... SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 TYPICAL CHARACTERISTICS TURNON TIME vs INPUT VOLTAGE TURNOFF TIME vs INPUT VOLTAGE 1.0 2 CL = 100 mF, RL = 5W , TA = 25 C 0.9 1.9 0.7 Turnoff Time - mS Turnon Time - ms 0.8 CL = 100 mF, RL = 5W , TA = 25 C 0.6 0.5 0.4 0.3 0.2 1.8 1.7 1.6 0.1 0 2 3 4 5 VI - Input Voltage - V 1.5 6 2 4 5 VI - Input Voltage - V Figure 11. Figure 12. RISE TIME vs INPUT VOLTAGE FALL TIME vs INPUT VOLTAGE 6 0.25 0.6 CL = 1mF, RL = 5W , TA = 25C CL = 1 mF, RL = 5W , TA = 25 C 0.5 0.2 0.4 Fall Time - ms Rise Time - ms 3 0.3 0.15 0.1 0.2 0.05 0.1 0 0 2 3 4 5 VI - Input Voltage - V 6 2 Figure 13. 3 4 5 VI - Input Voltage - V 6 Figure 14. Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A 9 TPS2062A TPS2066A SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 ........................................................................................................................................... www.ti.com TYPICAL CHARACTERISTICS (continued) TPS2062A, TPS2066A SUPPLY CURRENT, OUTPUT ENABLED vs JUNCTION TEMPERATURE TPS2062A, TPS2066A SUPPLY CURRENT, OUTPUT DISABLED vs JUNCTION TEMPERATURE I I (IN) - Supply Current, Output Disabled - m A I I (IN) - Supply Current, Output Enabled - m A 70 VI = 5.5 V 60 50 VI = 5 V VI = 3.3 V 40 30 VI = 2.7 V 20 10 0 -50 0 50 100 0.5 VI = 5.5 V 0.45 VI = 5 V 0.4 0.35 0.3 0.25 0.2 0.15 0.1 0.05 0 -50 150 VI = 3.3 V VI = 2.7 V 0 Figure 15. On-State Resistance - m 100 r DS(on) - Static Drain-Source 150 SHORT-CIRCUIT OUTPUT CURRENT vs JUNCTION TEMPERATURE 1.56 I OS - Short-Circuit Output Current -A Out1 = 5 V Out1 = 3.3 V 80 100 Figure 16. STATIC DRAIN-SOURCE ON-STATE RESISTANCE vs JUNCTION TEMPERATURE 120 IO = 0.5 A 50 TJ - Junction Temperature - C TJ - Junction Temperature - C Out1 = 2.7 V 60 40 20 VI = 2.7 V 1.54 1.52 VI = 3.3 V 1.5 1.48 1.46 1.44 VI = 5 V 1.42 VI = 5.5 V 1.4 1.38 1.36 0 1.34 -50 0 50 100 150 -50 TJ - Junction Temperature -C Figure 17. 10 0 50 100 150 TJ - Junction Temperature -C Figure 18. Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A TPS2062A TPS2066A www.ti.com ........................................................................................................................................... SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 TYPICAL CHARACTERISTICS (continued) THRESHOLD TRIP CURRENT vs INPUT VOLTAGE UNDERVOLTAGE LOCKOUT vs JUNCTION TEMPERATURE 2.3 2.5 UVLO Rising UVOL - Undervoltage Lockout - V TA = 25C Load Ramp = 1A/10 ms Threshold Trip Current - A 2.3 2.1 1.9 1.7 1.5 2.5 3 3.5 4 4.5 5 5.5 6 2.26 2.22 UVLO Falling 2.18 2.14 2.1 -50 0 50 100 150 TJ - Junction Temperature - C VI - Input Voltage - V Figure 19. Figure 20. CURRENT-LIMIT RESPONSE vs PEAK CURRENT 200 Current-Limit Response - m s VI = 5 V, TA = 25C 150 100 50 0 0 2.5 5 7.5 Peak Current - A Figure 21. 10 12.5 Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A 11 TPS2062A TPS2066A SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 ........................................................................................................................................... www.ti.com APPLICATION INFORMATION INPUT AND OUTPUT CAPACITANCE Input and output capacitance improve the performance of the device; the actual capacitance should be optimized for the particular application. For all applications, a 0.01 F to 0.1 F ceramic bypass capacitor between IN and GND is recommended and should be placed as close to the device as possible for local noise de-coupling. This precaution reduces ringing on the input due to power-supply transients . Additional input capacitance may be needed on the input to reduce voltage overshoot from exceeding the absolute maximum voltage of the device during heavy transients. Placing a high-value electrolytic capacitor on the output pin is recommended when the output load is heavy. Additionally, bypassing the output with a 0.01 F to 0.1 F ceramic capacitor improves the immunity of the device to short-circuit transients. POWER DISSIPATION AND JUNCTION TEMPERATURE The low on-resistance of the N-channel MOSFETs allows the small surface-mount packages to pass large currents. It is good design practice to check power dissipation to ensure that the junction temperature of the device is within the recommended operating conditions. The below analysis gives an approximation for calculating junction temperature based on the power dissipation in the package. However, it is important to note that thermal analysis is strongly dependent on additional system level factors. Such factors include air flow, board layout, copper thickness and surface area, and proximity to other devices dissipating power. Good thermal design practice must include all system level factors in addition to individual component analysis. The following procedure shows how to approximate the junction temperature rise due to power dissipation in a single channel. The TPS2062A/66A devices contain two channels, so the total device power must sum the power in each power switch. Begin by determining the rDS(on) of the N-channel MOSFET relative to the input voltage and operating temperature. Use the highest operating ambient temperature of interest and read rDS(on) from the typical characteristics graph as an initial estimate. Power dissipation is calculated by: PD = rDS(on)x IOUT2 PT = 2 x PD Where: PD = Power dissipation/channel (W) PT = Total power dissipation for both channels (W) rDS(on) = Power switch on-resistance () IOUT = Maximum current-limit threshold (A) Finally, calculate the junction temperature: TJ = PT x RJA + TA Where: TA= Ambient temperature C RJA = Thermal resistance (C/W) PT = Total power dissipation (W) Compare the calculated junction temperature with the initial estimate. If they are not within a few degrees, repeat the calculation using the "refined" rDS(on) from the previous calculation as the new estimate. Two or three iterations are generally sufficient to achieve the desired result. The final junction temperature is highly dependent on thermal resistance RJA, and thermal resistance is highly dependent on the individual package and board layout. The "Dissipation Rating Table" at the begginng of this document provides example thermal resistances for specific packages and board layouts. 12 Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A TPS2062A TPS2066A www.ti.com ........................................................................................................................................... SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 UNIVERSAL SERIAL BUS (USB) APPLICATIONS One application for this device is for current-limiting in universal serial bus (USB) applications. The original USB interface was a 12-Mb/s or 1.5-Mb/s, multiplexed serial bus designed for low-to-medium bandwidth PC peripherals (e.g., keyboards, printers, scanners, and mice). As the demand for more bandwidth increased, the USB 2.0 standard was introduced increasing the maximum data rate to 480-Mb/s. The four-wire USB interface is conceived for dynamic attach-detach (hot plug-unplug) of peripherals. Two lines are provided for differential data, and two lines are provided for 5-V power distribution. USB data is a 3.3-V level signal, but power is distributed at 5 V to allow for voltage drops in cases where power is distributed through more than one hub across long cables. Each function must provide its own regulated 3.3 V from the 5-V input or its own internal power supply. The USB specification classifies two different classes of devices depending on its maximum current draw. A device classified as low-power can draw up to 100 mA as defined by the standard. A device classified as high-power can draw up to 500 mA. It is important that the minimum current limit threshold of the current-limiting power switch exceed the maximum current limit draw of the intended application. The latest USB standard should always be referenced when considering the current-limit threshold. The USB specification defines two types of devices as hubs and functions. A USB hub is a device that contains multiple ports for different USB devices to connect and can be self-powered (SPH) or bus-powered (BPH). A function is a USB device that is able to transmit or receive data or control information over the bus. A USB function can be embedded in a USB hub. A USB function can be one of three types included in the list below. * Low-power, bus-powered function * High-power, bus-powered function * Self-powered function SPHs and BPHs distribute data and power to downstream functions. The TPS206x6A has higher current capability than required for a single USB port allowing it to power multiple downstream ports. SELF-POWERED AND BUS-POWERED HUBS A SPH has a local power supply that powers embedded functions and downstream ports. This power supply must provide between 4.75 V to 5.25 V to downstream facing devices under full-load and no-load conditions. SPHs are required to have current-limit protection and must report overcurrent conditions to the USB controller. Typical SPHs are desktop PCs, monitors, printers, and stand-alone hubs. A BPH obtains all power from an upstream port and often contains an embedded function. It must power up with less than 100 mA. The BPH usually has one embedded function, and power is always available to the controller of the hub. If the embedded function and hub require more than 100 mA on power up, the power to the embedded function may need to be kept off until enumeration is completed. This is accomplished by removing power or by shutting off the clock to the embedded function. Power switching the embedded function is not necessary if the aggregate power draw for the function and controller is less than 100 mA. The total current drawn by the bus-powered device is the sum of the current to the controller, the embedded function, and the downstream ports, and it is limited to 500 mA from an upstream port. LOW-POWER BUS-POWERED AND HIGH-POWER BUS-POWERED FUNCTIONS Both low-power and high-power bus-powered functions obtain all power from upstream ports. Low-power functions always draw less than 100 mA; high-power functions must draw less than 100 mA at power up and can draw up to 500 mA after enumeration. If the load of the function is more than the parallel combination of 44 and 10 F at power up, the device must implement inrush current limiting. Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A 13 TPS2062A TPS2066A SLVS798F - JANUARY 2008 - REVISED NOVEMBER 2008 ........................................................................................................................................... www.ti.com USB POWER-DISTRIBUTION REQUIREMENTS USB can be implemented in several ways regardless of the type of USB device being developed. Several power-distribution features must be implemented. * SPHs must: - Current-limit downstream ports - Report overcurrent conditions * BPHs must: - Enable/disable power to downstream ports - Power up at <100 mA - Limit inrush current (<44 and 10 F) * Functions must: - Limit inrush currents - Power up at <100 mA The feature set of the TPS2062A/66A meets each of these requirements. The integrated current-limiting and overcurrent reporting is required by self-powered hubs. The logic-level enable and controlled rise times meet the need of both input and output ports on bus-powered hubs and the input ports for bus-powered functions. 14 Submit Documentation Feedback Copyright (c) 2008, Texas Instruments Incorporated Product Folder Link(s): TPS2062A TPS2066A PACKAGE OPTION ADDENDUM www.ti.com 11-Jul-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TPS2062AD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2062ADG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2062ADR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2062ADRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2062ADRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2062ADRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2062ADRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2062ADRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2066AD ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2066ADG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2066ADR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2066ADRBR ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2066ADRBRG4 ACTIVE SON DRB 8 3000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2066ADRBT ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2066ADRBTG4 ACTIVE SON DRB 8 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TPS2066ADRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 11-Jul-2008 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 10-Jul-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPS2062ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS2062ADRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TPS2062ADRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TPS2066ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS2066ADRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TPS2066ADRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 10-Jul-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS2062ADR TPS2062ADRBR SOIC D 8 2500 340.5 338.1 20.6 SON DRB 8 3000 370.0 355.0 55.0 TPS2062ADRBT SON DRB 8 250 195.0 200.0 45.0 TPS2066ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2066ADRBR SON DRB 8 3000 370.0 355.0 55.0 TPS2066ADRBT SON DRB 8 250 195.0 200.0 45.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2011 TAPE AND REEL INFORMATION *All dimensions are nominal Device TPS2062ADR Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS2062ADRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TPS2066ADR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 TPS2066ADRBR SON DRB 8 3000 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 TPS2066ADRBT SON DRB 8 250 180.0 12.4 3.3 3.3 1.0 8.0 12.0 Q2 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 16-Aug-2011 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPS2062ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2062ADRBR SON DRB 8 3000 346.0 346.0 35.0 TPS2066ADR SOIC D 8 2500 340.5 338.1 20.6 TPS2066ADRBR SON DRB 8 3000 346.0 346.0 35.0 TPS2066ADRBT SON DRB 8 250 203.0 203.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com Wireless www.ti.com/wireless-apps RF/IF and ZigBee(R) Solutions www.ti.com/lprf TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated