Data sheet acquired from Cypress Semiconductor Corporation. Data sheet modified to remove devices not offered. CY74FCT163500 18-Bit Registered Transceiver SCCS066 - June 1997 - Revised March 2000 Features Functional Description * Low power, pin-compatible replacement for LCX and LPT families * 5V tolerant inputs and outputs * 24 mA balanced drive outputs * Power-off disable outputs permits live insertion * Edge-rate control circuitry for reduced noise * FCT-C speed at 4.6 ns * Latch-up performance exceeds JEDEC standard no. 17 * ESD > 2000V per MIL-STD-883D, Method 3015 * Typical output skew < 250ps * Industrial temperature range of -40C to +85C * TSSOP (19.6-mil pitch) or SSOP (25-mil pitch) * Typical Volp (ground bounce) performance exceeds Mil Std 883D * VCC = 2.7V to 3.6V The CY74FCT163500 is an 18-bit universal bus transceiver that can be operated in transparent, latched, or clock modes by combining D-type latches and D-type flip-flops. Data flow in each direction is controlled by output-enable (OEAB and OEBA), latch enable (LEAB and LEBA), and clock inputs (CLKAB and CLKBA) inputs. For A-to-B data flow, the device operates in transparent mode when LEAB is HIGH. When LEAB is LOW, the A data is latched if CLKAB is held at a HIGH or LOW logic level. If LEAB is LOW, the A bus data is stored in the latch/flip-flop on the HIGH-to-LOW transition of CLKAB. OEAB performs the output enable function on the B port. Data flow from B-to-A is similar to that of A-to-B and is controlled by OEBA, LEBA, and CLKBA. The CY74FCT163500 has 24-mA balanced output drivers with current limiting resistors in the outputs. This reduces the need for external terminating resistors and provides for minimal undershoot and reduced ground bounce.The inputs and outputs are capable of being driven by 5.0V busses, allowing them to be used in mixed voltage systems as translators. The outputs are also designed with a power off disable feature enabling them to be used in applications requiring live insertion. Logic Block Diagram Pin Configuration SSOP/TSSOP Top View OEAB LEAB 1 56 2 55 GND CLKAB A1 3 54 B1 GND 4 53 GND A2 5 52 B2 A3 6 51 B3 VCC 7 50 VCC A4 49 B4 OEBA 8 A5 9 48 B5 CLKAB A6 10 47 B6 GND 11 46 GND A7 12 13 45 B7 44 B8 A9 A 10 14 43 B9 15 42 B10 A 11 16 41 B11 A 12 17 40 B12 GND 18 39 38 GND B13 OEAB CLKBA LEBA LEAB A8 C C B1 A1 D D C C A 13 19 D D A 14 20 37 B14 A 15 21 36 B15 VCC 22 35 VCC A 16 A 17 23 34 B16 24 25 33 B17 32 GND 26 31 B18 27 30 CLKBA 28 29 GND TO 17 OTHER CHANNELS GND A 18 OEBA LEBA Copyright (c) 2000, Texas Instruments Incorporated CY74FCT163500 Maximum Ratings[5, 6] Pin Summary Name Description (Above which the useful life may be impaired. For user guidelines, not tested.) OEAB A-to-B Output Enable Input OEBA B-to-A Output Enable Input (Active LOW) Storage Temperature ................................ -55C to +125C LEAB A-to-B Latch Enable Input Ambient Temperature with Power Applied ................................................. -55C to +125C LEBA B-to-A Latch Enable Input Supply Voltage Range ..................................... 0.5V to +4.6V CLKAB A-to-B Clock Input (Active LOW) DC Input Voltage .................................................-0.5V to +7.0V CLKBA B-to-A Clock Input (Active LOW) DC Output Voltage ..............................................-0.5V to +7.0V A A-to-B Data Inputs or B-to-A Three-State Outputs B B-to-A Data Inputs or A-to-B Three-State Outputs DC Output Current (Maximum Sink Current/Pin) ...........................-60 to +120 mA Power Dissipation .......................................................... 1.0W Function Table[1, 2] Inputs Static Discharge Voltage............................................>2001V (per MIL-STD-883, Method 3015) Outputs OEAB LEAB CLKAB A B L X X X Z H H X L L H H X H H H L L L H L H H H L H X B[3] H L L X B[4] Operating Range Range Industrial Ambient Temperature VCC -40C to +85C 2.7V to 3.6V Notes: 1. H = HIGH Voltage Level. L = LOW Voltage Level. X = Don't Care. Z = HIGH Impedance. = HIGH-to-LOW Transition. 2. A-to-B data flow is shown, B-to-A data flow is similar but uses OEBA, LEBA, and CLKBA. 3. Output level before the indicated steady-state input conditions were established. 4. Output level before the indicated steady-state input conditions were established, provided that CLKAB was LOW before LEAB went LOW. 5. Operation beyond the limits set forth may impair the useful life of the device. Unless noted, these limits are over the operating free-air temperature range. 6. Unused inputs must always be connected to an appropriate logic voltage level, preferably either VCC or ground. 2 CY74FCT163500 Electrical Characteristics Over the Operating Range VCC=2.7V to 3.6V Parameter Description VIH Input HIGH Voltage VIL Input LOW Voltage Test Conditions All Inputs Min. Typ.[7] 2.0 [8] VH Input Hysteresis VIK Input Clamp Diode Voltage VCC=Min., IIN=-18 mA IIH Input HIGH Current IIL Input LOW Current IOZH Max. Unit 5.5 V 0.8 V 100 -1.2 V VCC=Max., VI=5.5V 1 A VCC=Max., VI=GND. 1 A High Impedance Output Current (Three-State Output pins) VCC=Max., VOUT=5.5V 1 A IOZL High Impedance Output Current (Three-State Output pins) VCC=Max., VOUT=GND 1 A IODL Output LOW Current[9] VCC=3.3V, VIN=VIH or VIL, VOUT=1.5V 45 180 mA IODH Output HIGH Current[9] VCC=3.3V, VIN=VIH or VIL, VOUT=1.5V -45 -180 mA VOH Output HIGH Voltage VCC=Min., IOH= -0.1 mA VOL Output LOW Voltage -0.7 mV VCC-0.2 VCC=3.0V, IOH= -8 mA 2.4 3.0 VCC=3.0V, IOH= -24 mA 2.0 3.0 VCC=Min., IOL= 0.1mA IOS Short Circuit IOFF Power-Off Disable VCC=Max., VOUT=GND V V 0.2 VCC=Min., IOL= 24 mA Current[9] V -60 V 0.3 0.5 -135 -240 mA 100 A Typ.[7] Max. Unit VCC=0V, VOUT4.5V Capacitance[8] (TA = +25C, f = 1.0 MHz) Parameter Description Test Conditions CIN Input Capacitance VIN = 0V 4.5 6.0 pF COUT Output Capacitance VOUT = 0V 5.5 8.0 pF Notes: 7. Typical values are at VCC=3.3V, TA = +25C ambient. 8. This parameter is specified but not tested. 9. Not more than one output should be shorted at a time. Duration of short should not exceed one second. The use of high-speed test apparatus and/or sample and hold techniques are preferable in order to minimize internal chip heating and more accurately reflect operational values. Otherwise prolonged shorting of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parametric tests. In any sequence of parameter tests, IOS tests should be performed last. 3 CY74FCT163500 Power Supply Characteristics Parameter Description Test Conditions Typ.[7] Max. Unit ICC Quiescent Power Supply Current VCC=Max. VIN0.2V, VINVCC-0.2V 0.1 10 A ICC Quiescent Power Supply Current (TTL inputs HIGH) VCC=Max. VIN=VCC-0.6V[10] 2.0 30 A ICCD Dynamic Power Supply Current[11] VCC=Max., One Input Toggling, VIN=VCC or 50%DutyCycle,OutputsOpen, VIN=GND OEAB=OEBA=VCC or GND 50 75 A/MHz IC Total Power Supply Current[12] VCC=Max., f0=10 MHz (CLKAB), f1=5 MHz, 50% Duty Cycle, Outputs Open, One Bit Toggling, OEAB=OEBA=VCC LEAB=GND VIN=VCC or VIN=GND 0.5 0.8 mA VIN=VCC-0.6V or VIN=GND 0.5 0.8 mA VIN=VCC or VIN=GND 2.5 3.8[13] mA VIN=VCC-0.6V or VIN=GND 2.6 4.1[13] mA VCC=Max., f0=10 MHz, f1=2.5 MHz, 50% Duty Cycle, Outputs Open, Eighteen Bits Toggling, OEAB=OEBA=VCC LEAB=GND Notes: 10. Per TTL driven input; all other inputs at VCC or GND. 11. This parameter is not directly testable, but is derived for use in Total Power Supply calculations. 12. IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC+ICCDHNT+ICCD(f0NC /2 + f1N1) ICC = Quiescent Current with CMOS input levels ICC = Power Supply Current for a TTL HIGH input (VIN=3.4V) = Duty Cycle for TTL inputs HIGH DH = Number of TTL inputs at DH NT ICCD = Dynamic Current caused by an input transition pair (HLH or LHL) = Clock frequency for registered devices, otherwise zero f0 = Number of clock inputs changing at f1 NC f1 = Input signal frequency = Number of inputs changing at f1 N1 All currents are in milliamps and all frequencies are in megahertz. 13. Values for these conditions are examples of the ICC formula. These limits are specified but not tested. 4 CY74FCT163500 Switching Characteristics Over the Operating Range VCC = 3.0V to 3.6V[,14, 15] CY74FCT163500A Parameter Description Min. Max. CY74FCT163500C Min. 150 Max. Unit 150 MHz Fig. No.[16] fMAX CLKAB or CLKBA frequency tPLH tPHL Propagation Delay A to B or B to A 1.5 5.1 1.5 4.6 ns 1, 3 tPLH tPHL Propagation Delay LEBA to A, LEAB to B 1.5 5.6 1.5 5.3 ns 1, 5 tPLH tPHL Propagation Delay CLKBA to A, CLKAB to B 1.5 5.6 1.5 5.3 ns 1, 5 tPZH tPZL Output Enable Time OEBA to A, OEAB to B 1.5 6.0 1.5 5.4 ns 1, 7, 8 tPHZ tPLZ Output Disable Time OEBA to A, OEAB to B 1.5 5.6 1.5 5.2 ns 1, 7, 8 tSU Set-Up Time, HIGH or LOW A to CLKAB, B to CLKBA 3.0 3.0 ns 9 tH Hold Time, HIGH or LOW A to CLKAB, B to CLKBA 0 0 ns 9 tSU Set-Up Time, HIGH or LOW A to LEAB, B to LEBA Clock HIGH 3.0 3.0 ns 4 Clock LOW 1.5 1.5 ns 4 tH Hold Time, HIGH or LOW A to LEAB, B to LEBA 1.5 1.5 ns 4 tW LEAB or LEBA Pulse Width HIGH 3.0 2.5 ns 5 tW CLKAB or CLKBA Pulse Width HIGH or LOW 3.0 3.0 ns 5 tSK(O) Output Skew[17] 0.5 0.5 ns Ordering Information CY74FCT163500 Speed (ns) 4.6 5.1 Ordering Code Package Name Package Type CY74FCT163500CPACT Z56 56-Lead (240-Mil) TSSOP CY74FCT163500CPVC/PVCT O56 56-Lead (300-Mil) SSOP CY74FCT163500APVC/PVCT O56 56-Lead (300-Mil) SSOP Notes: 14. Minimum limits are specified but not tested on Propagation Delays. 15. For VCC =2.7, propagation delay, output enable and output disable times should be degraded by 20%. 16. See "Parameter Measurement Information" in the General Information section. 17. Skew between any two outputs of the same package switching in the same direction. This parameter is ensured by design. 5 Operating Range Industrial Industrial CY74FCT163500 Package Diagrams 56-Lead Shrunk Small Outline Package O56 56-Lead Thin Shrunk Small Outline Package Z56 6 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI's publication of information regarding any third party's products or services does not constitute TI's approval, warranty or endorsement thereof. Copyright 2000, Texas Instruments Incorporated