19-1156; Rev 2; 6/98 +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 ________________________________Features The MAX1242/MAX1243 are low-power, 10-bit analogto-digital converters (ADCs) available in 8-pin packages. They operate with a single +2.7V to +5.25V supply and feature a 7.5s successive-approximation ADC, a fast track/hold (1.5s), an on-chip clock, and a high-speed, 3-wire serial interface. Power consumption is only 3mW (VDD = 3V) at the 73ksps maximum sampling speed. A 2A shutdown mode reduces power at slower throughput rates. +2.7V to +5.25V Single-Supply Operation The MAX1242 has an internal 2.5V reference, while the MAX1243 requires an external reference. The MAX1243 accepts signals from 0V to VREF, and the reference input range includes the positive supply rail. An external clock accesses data from the 3-wire interface, which connects directly to standard microcontroller I/O ports. The interface is compatible with SPITM, QSPITM, and MicrowireTM. Excellent AC characteristics and very low power combined with ease of use and small package size make these converters ideal for remote-sensor and dataacquisition applications, or for other circuits with demanding power consumption and space requirements. The MAX1242/MAX1243 are available in 8-pin DIP and SO packages. Applications Portable Data Logging Process Control Monitoring Test Equipment Temperature Measurement 10-Bit Resolution Internal 2.5V Reference (MAX1242) Small Footprint: 8-Pin DIP and SO Packages Low Power: 3.7mW (73ksps, MAX1242) 3mW (73ksps, MAX1243) 66W (1ksps, MAX1243) 5W (power-down mode) Internal Track/Hold SPITM/QSPITM/MicrowireTM 3-Wire Serial Interface Pin-Compatible 12-Bit Upgrades: MAX1240/MAX1241 _________________Ordering Information PART TEMP. RANGE PINPACKAGE INL (LSB) MAX1242ACPA 0C to +70C 8 Plastic DIP 1/2 MAX1242BCPA 0C to +70C 8 Plastic DIP 1 MAX1242ACSA 0C to +70C 8 SO 1/2 MAX1242BCSA 0C to +70C 8 SO 1 MAX1242AEPA -40C to +85C 8 Plastic DIP 1/2 MAX1242BEPA -40C to +85C 8 Plastic DIP 1 Ordering Information continued at end of data sheet. Note: Order the MAX1242A in place of the MAX1242C. Order the MAX1242B in place of the MAX1242D. Isolated Data Acquisition ________________Functional Diagram Pin Configuration VDD 1 CS SCLK TOP VIEW SHDN VDD 1 AIN 2 SHDN 3 MAX1242 MAX1243 REF 4 DIP/SO 8 SCLK 7 CS 6 DOUT 5 GND AIN 7 8 3 2 INT CLOCK CONTROL LOGIC T/H 4 6 DOUT 10-BIT SAR 2.5V REFERENCE REF OUTPUT SHIFT REGISTER MAX1242 MAX1243 MAX1242 ONLY 5 GND SPI and QSPI are trademarks of Motorola, Inc. Microwire is a trademark of National Semiconductor Corp. ________________________________________________________________ Maxim Integrated Products 1 For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 408-737-7600 ext. 3468. MAX1242/MAX1243 __________________General Description MAX1242/MAX1243 +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 ABSOLUTE MAXIMUM RATINGS VDD to GND .............................................................-0.3V to +6V AIN to GND................................................-0.3V to (VDD + 0.3V) REF to GND ...............................................-0.3V to (VDD + 0.3V) Digital Inputs to GND...............................................-0.3V to +6V DOUT to GND............................................-0.3V to (VDD + 0.3V) DOUT Current ..................................................................25mA Continuous Power Dissipation (TA = +70C) Plastic DIP (derate 9.09mW/C above +70C) ...........727mW SO (derate 5.88mW/C above +70C)........................471mW CERDIP (derate 8.00mW/C above +70C)................640mW Operating Temperature Ranges MAX1242/MAX1243_C_A ..................................0C to +70C MAX1242/MAX1243_E_ A ..............................-40C to +85C MAX1242/MAX1243_MJA ............................-55C to +125C Storage Temperature Range............................-60C to +150C Lead Temperature (soldering, 10sec)............................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VDD = +2.7V to +5.25V; 73ksps; fSCLK = 2.1MHz (50% duty cycle); MAX1242--4.7F capacitor at REF pin, MAX1243--external reference; VREF = 2.5V applied to REF pin; TA = TMIN to TMAX; unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS DC ACCURACY (Note1) (Note 1) Resolution 10 Relative Accuracy (Note 2) Differential Nonlinearity DNL Offset Error Gain Error (Note 3) Bits MAX124_A 0.5 MAX124_B 1.0 No missing codes over temperature 1 MAX124_A 1 MAX124_B 2 MAX124_A 1 MAX124_B 2 Gain Temperature Coefficient LSB LSB LSB LSB 0.25 ppm/C 66 dB -70 dB DYNAMIC SPECIFICATIONS (10kHz sine-wave input, 0V to 2.5p-p, 2.5Vp-p,73ksps, 73ksps,fSCLK fSCLK=2.1MHz) = 2.1MHz) Signal-to-Noise Plus Distortion Ratio SINAD Total Harmonic Distortion THD Spurious-Free Dynamic Range SFDR Small-Signal Bandwidth Up to the 5th harmonic -3dB rolloff Full-Power Bandwidth 70 dB 2.25 MHz 1.0 MHz CONVERSION RATE Conversion Time tCONV Track/Hold Acquisition Time tACQ Throughput Rate Aperture Delay 5.5 7.5 fSCLK = 2.1MHz tAP Figure 9 Aperture Jitter s 1.5 s 73 ksps 30 ns <50 ps ANALOG INPUT Input Voltage Range Input Capacitance 2 0 VREF 16 _______________________________________________________________________________________ V pF +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 ELECTRICAL CHARACTERISTICS (continued) (VDD = +2.7V to +5.25V; 73ksps; fSCLK = 2.1MHz (50% duty cycle); MAX1242--4.7F capacitor at REF pin, MAX1243--external reference; VREF = 2.5V applied to REF pin; TA = TMIN to TMAX; unless otherwise noted.) PARAMETER SYMBOL INTERNAL REFERENCE (MAX1242 only) REF Output Voltage REF Short-Circuit Current REF Temperature Coefficient Load Regulation (Note 5) CONDITIONS TA = +25C (Note 4) MIN TYP MAX UNITS 2.470 2.500 2.530 30 V mA ppm/C mV MAX1242 0mA to 0.2mA output load 30 0.35 Capacitive Bypass at REF 4.7 F EXTERNAL REFERENCE (VREF = 2.5V) 1.00 Input Voltage Range Input Current Input Resistance REF Input Current in Shutdown Capacitive Bypass at REF 18 SHDN = 0V 100 25 0.01 VDD + 50mV 150 10 0.1 V A k A F DIGITAL INPUTS: SCLK, CS, SHDN SCLK, CS Input High Voltage SCLK, CS Input Low Voltage SCLK, CS Input Hysteresis VIH VDD 3.6V VDD > 3.6V 2.0 3.0 V VIL VHYST SCLK, CS Input Leakage IIN VIN = 0V or VDD SCLK, CS Input Capacitance CIN (Note 6) SHDN Input High Voltage VSH SHDN Input Low Voltage VSL SHDN Input Current 0.01 VSM SHDN Voltage, Floating VFLT SHDN Max Allowed Leakage, Mid Input V 1 A 15 pF V VDD - 0.4 V SHDN = 0V or VDD SHDN Input Mid Voltage 0.8 0.2 1.1 SHDN = float 0.4 V 4.0 A VDD - 1.1 VDD / 2 SHDN = float V V 100 nA 0.4 0.8 V DIGITAL OUTPUT: DOUT Output Voltage Low VOL Output Voltage High Three-State Leakage Current VOH IL Three-State Output Capacitance COUT ISINK = 5MA ISINK = 16mA ISOURCE = 0.5mA VDD - 0.5 CS = VDD 0.01 CS = VDD (Note 6) 10 V A 15 pF 5.25 V POWER REQUIREMENTS Supply Voltage VDD 2.7 Operating mode (MAX1242) Operating mode (MAX1242) Supply Current IDD Power-Supply Rejection (Note 7) PSR VDD = 3.6V VDD = 5.25V VDD = 3.6V Operating mode (MAX1243) VDD = 5.25V VDD = 3.6V Power-down VDD = 5.25V VDD = VDD(min) to VDD(max), full-scale input 1.4 1.8 0.9 1.6 1.9 3.5 0.3 2.0 3.0 1.5 2.5 10 15 mA A mV _______________________________________________________________________________________ 3 MAX1242/MAX1243 +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 TIMING CHARACTERISTICS (VDD = +2.7V to +5.25V, circuit of Figure 9, TA = TMIN to TMAX, unless otherwise noted.) PARAMETER SYMBOL CS = VDD (Note 8) SCLK Fall to Output Data Valid tDO Figure 1, CLOAD = 50pF CS Fall to Output Enable tDV Figure 1, CLOAD = 50pF tTR Figure 2, CLOAD = 50pF CS Rise to Output Disable MIN CONDITIONS tACQ Acquisition Time TYP MAX 1.5 UNITS s MAX124_ _C/E 20 200 MAX124_ _M 20 240 240 ns ns 240 ns 2.1 MHz SCLK Clock Frequency fSCLK 0 SCLK Pulse Width High tCH 200 ns SCLK Pulse Width Low tCL 200 ns SCLK Low to CS Fall Setup Time tCS0 50 ns DOUT Rise to SCLK Rise (Note 6) tSTR 0 ns CS Pulse Width tCS 240 ns Note 1: Tested at VDD = +2.7V. Note 2: Relative accuracy is the deviation of the analog value at any code from its theoretical value after the full-scale range and offset have been calibrated. Note 3: Offset nulled. Note 4: Sample tested to 0.1% AQL. Note 5: External load should not change during conversion for specified accuracy. Note 6: Guaranteed by design. Not subject to production testing. Note 7: Measured as [VFS (VDD(min)) - VFS (VDD(max))]. Note 8: To guarantee acquisition time, tACQ is the maximum time the device takes to acquire the signal, and is also the minimum time needed for the signal to be acquired. +2.7V 6k DOUT DOUT 6k CLOAD = 50pF CLOAD = 50pF DGND DGND a) High-Z to VOH and VOL to VOH b) High-Z to VOL and VOH to VOL Figure 1. Load Circuits for DOUT Enable Time +2.7V 6k DOUT DOUT 6k CLOAD = 50pF CLOAD = 50pF DGND DGND a) VOH to High-Z b) VOLto High-Z Figure 2. Load Circuits for DOUT Disable Time 4 _______________________________________________________________________________________ +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 SHUTDOWN SUPPLY CURRENT vs. SUPPLY VOLTAGE 1.50 CLOAD = 50pF MAX1242 1.25 CLOAD = 50pF MAX1243 1.00 CLOAD = 20pF 0.75 RL = CODE = 1010101000 0.50 2.25 2.75 3.25 3.75 4.25 4.75 2.0 1.5 1.0 0 2.25 5.25 2.75 3.25 3.75 4.25 4.75 2.5005 2.5000 2.4995 2.4990 2.4985 2.25 5.25 MAX1242/43-03 MAX1242/43-02 2.5 0.5 2.75 3.25 3.75 SUPPLY VOLTAGE (V) SUPPLY CURRENT vs. TEMPERATURE SHUTDOWN CURRENT vs. TEMPERATURE INTERNAL REFERENCE VOLTAGE vs. TEMPERATURE 2.75 1.0 MAX1243 0.9 2.50 2.25 2.00 1.75 1.50 1.25 RLOAD = CODE = 1010101000 2.501 MAX1242 INTERNAL REFERENCE VOLTAGE (V) 1.1 MAX1242/43-05 MAX1242/43-04 MAX1242 3.00 SHUTDOWN CURRENT (A) 1.00 -20 20 60 100 140 2.500 VDD = 3.6V VDD = 5V 2.499 VDD = 2.7V 2.498 2.497 2.496 2.495 2.494 -60 -20 20 60 100 -60 -40 -20 0 140 20 40 60 80 100 120 140 TEMPERATURE (C) TEMPERATURE (C) TEMPERATURE (C) INTEGRAL NONLINEARITY vs. SUPPLY VOLTAGE INTEGRAL NONLINEARITY vs. TEMPERATURE INTEGRAL NONLINEARITY vs. CODE 0.30 MAX1242/43-07 0.30 0.25 VDD = 2.7V 0.15 0.25 0.10 0.20 INL (LSB) 0.20 0.15 0.05 0.15 0.10 MAX1242 0.10 MAX1242/43-09 -60 INL (LSB) SUPPLY CURRENT (mA) 3.0 MAX1242 2.5010 SUPPLY VOLTAGE (V) 1.2 INL (LSB) MAX1242/MAX1243 SUPPLY VOLTAGE (V) 1.3 0.8 3.5 MAX1242/43-06 CLOAD = 20pF 2.5015 MAX1242/43-08 SUPPLY CURRENT (mA) 1.75 4.0 SHUTDOWN SUPPLY CURRENT (A) MAX1242/43-01 2.00 INTERNAL REFERENCE VOLTAGE vs. SUPPLY VOLTAGE INTERNAL REFERENCE VOLTAGE (V) SUPPLY CURRENT vs. SUPPLY VOLTAGE 0 -0.05 MAX1242 0.05 0.05 -0.10 MAX1243 MAX1243 0 0 2.25 2.75 3.25 3.75 4.25 SUPPLY VOLTAGE (V) 4.75 5.25 -0.15 -60 -40 -20 0 20 40 60 80 100 120 140 TEMPERATURE (C) 0 256 512 CODE 768 1024 _______________________________________________________________________________________ 5 MAX1242/MAX1243 __________________________________________Typical Operating Characteristics (VDD = +3.0V, VREF = 2.5V, fSCLK = 2.1MHz, CLOAD = 20pF, TA = +25C, unless otherwise noted.) MAX1242/MAX1243 +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 ______________________________________________________________Pin Description PIN NAME 1 VDD Positive Supply Voltage: +2.7V to +5.25V FUNCTION 2 AIN Sampling Analog Input, 0V to VREF range Three-Level Shutdown Input. Pulling SHDN low shuts the MAX1242/MAX1243 down to 15A (max) supply current. Both MAX1242 and MAX1243 are fully operational with either SHDN high or floating. For the MAX1242, pulling SHDN high enables the internal reference, and letting SHDN float disables the internal reference and allows for the use of an external reference. 3 SHDN 4 REF Reference Voltage for Analog-to-Digital Conversion. Internal 2.5V reference output for MAX1242; bypass with a 4.7F capacitor. External reference voltage input for MAX1243, or for MAX1242 with the internal reference disabled. Bypass REF with a minimum of 0.1F when using an external reference. 5 GND Analog and Digital Ground 6 DOUT Serial-Data Output. Data changes state at SCLK's falling edge. High impedance when CS is high. 7 CS Active-Low Chip Select. Initiates conversions on the falling edge. When CS is high, DOUT is high impedance. 8 SCLK Serial-Clock Input. SCLK clocks data out at rates up to 2.1MHz. _______________Detailed Description Converter Operation The MAX1242/MAX1243 use an input track/hold (T/H) and successive-approximation register (SAR) circuitry to convert an analog input signal to a digital 10-bit output. Figure 3 shows the MAX1242/MAX1243 in their simplest configuration. The MAX1242/MAX1243 convert input signals in the 0V to VREF range in 9s, including T/H acquisition time. The MAX1242's internal reference is trimmed to 2.5V, while the MAX1243 requires an external reference. Both devices accept external reference voltages from 1.0V to VDD. The serial interface requires only three digital lines (SCLK, CS, and DOUT) and provides an easy interface to microprocessors (Ps). The MAX1242/MAX1243 have two modes: normal and shutdown. Pulling SHDN low shuts the device down and reduces supply current below 10A (VDD 3.6V), while pulling SHDN high or leaving it open puts the devices into operational mode. A conversion is initiated by pulling CS low. The conversion result is available at DOUT in unipolar serial format. The serial-data stream consists of a high bit, signaling the end of conversion (EOC), followed by the data bits (MSB first). Analog Input Figure 4 illustrates the sampling architecture of the analog-to-digital converter's (ADC's) comparator. The fullscale input voltage is set by the voltage at REF. 6 Track/Hold In track mode, the analog signal is acquired and stored in the internal hold capacitor. In hold mode, the T/H switch opens and maintains a constant input to the ADC's SAR section. During acquisition, the analog input AIN charges capacitor CHOLD. Bringing CS low ends the acquisition interval. At this instant, the T/H switches the input side of CHOLD to GND. The retained charge on CHOLD represents a sample of the input, unbalancing node ZERO at the comparator's input. In hold mode, the capacitive digital-to-analog converter (DAC) adjusts during the remainder of the conversion cycle to restore node ZERO to 0V within the limits of 10bit resolution. This action is equivalent to transferring a charge from CHOLD to the binary-weighted capacitive DAC, which in turn forms a digital representation of the analog input signal. At the conversion's end, the input side of C HOLD switches back to AIN, and C HOLD charges to the input signal again. The time required for the T/H to acquire an input signal is a function of how quickly its input capacitance is charged. If the input signal's source impedance is high, the acquisition time lengthens, and more time must be allowed between conversions. The acquisition time, tACQ, is the maximum time the device takes to acquire the signal and the minimum time needed for the signal to be acquired. Acquisition time is calculated by: tACQ = 7(RS + RIN) x 16pF _______________________________________________________________________________________ +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 MAX1242/MAX1243 +2.7V to +5.25V CAPACITIVE DAC 4.7F 0.1F REF 1 2 ANALOG INPUT 0V TO VREF SHUTDOWN INPUT 3 REFERENCE INPUT 4 VDD AIN SCLK CS MAX1242 MAX1243 SHDN DOUT REF GND 8 7 AIN SERIAL INTERFACE HOLD ZERO - + 16pF CSWITCH 6 COMPARATOR TRACK INPUT CHOLD 9k RIN HOLD TRACK 5 C* MAX1243 AT THE SAMPLING INSTANT, THE INPUT SWITCHES FROM AIN TO GND. GND *4.7F, MAX1242 0.1F, MAX1243 Figure 3. Operational Diagram where RIN = 9k, RS = the input signal's source impedance, and tACQ is never less than 1.5s. Source impedances below 4k do not significantly affect the ADC's AC performance. Higher source impedances can be used if a 0.01F capacitor is connected to the analog input. Note that the input capacitor forms an RC filter with the input source impedance, limiting the ADC's input signal bandwidth. Input Bandwidth The ADC's input tracking circuitry has a 2.25MHz small-signal bandwidth, so it is possible to digitize high-speed transient events and measure periodic signals with bandwidths exceeding the ADC's sampling rate by using undersampling techniques. To avoid aliasing of unwanted high-frequency signals into the frequency band of interest, anti-alias filtering is recommended. Analog Input Protection Internal protection diodes, which clamp the analog input to VDD and GND, allow the input to swing from GND - 0.3V to VDD + 0.3V without damage. However, for accurate conversions near full scale, the input must not exceed VDD by more than 50mV, or be lower than GND by 50mV. If the analog input exceeds 50mV beyond the supplies, limit the input current to 2mA. Figure 4. Equivalent Input Circuit Internal Reference (MAX1242) The MAX1242 has an on-chip voltage reference trimmed to 2.5V. The internal reference output is connected to REF and also drives the internal capacitive DAC. The output can be used as a reference voltage source for other components and can source up to 400A. Bypass REF with a 4.7F capacitor. Larger capacitors increase wake-up time when exiting shutdown (see Using SHDN to Reduce Supply Current ). The internal reference is enabled by pulling the SHDN pin high. Letting SHDN float disables the internal reference, which allows the use of an external reference, as described in the External Reference section. External Reference The MAX1242/MAX1243 operate with an external reference at the REF pin. To use the MAX1242 with an external reference, disable the internal reference by letting SHDN float. Stay within the voltage range 1.0V to VDD to achieve specified accuracy. The minimum input impedance is 18k for DC currents. During conversion, the external reference must be able to deliver up to 250A of DC load current and have an output impedance of 10 or less. The recommended minimum value for the bypass capacitor is 0.1F. If the reference has higher output impedance or is noisy, bypass it close to the REF pin with a 4.7F capacitor. _______________________________________________________________________________________ 7 Using SHDN to Reduce Supply Current Serial Interface Initialization after Power-Up and Starting a Conversion When power is first applied, and if SHDN is not pulled low, it takes the fully discharged 4.7F reference bypass capacitor up to 20ms to provide adequate charge for specified accuracy. With an external reference, the internal reset time is 10s after the power supplies have stabilized. No conversions should be performed during these times. To start a conversion, pull CS low. At CS's falling edge, the T/H enters its hold mode and a conversion is initiated. After an internally timed conversion period, the end of conversion is signaled by DOUT pulling high. Data can then be shifted out serially with the external clock. Power consumption can be reduced significantly by shutting down the MAX1242/MAX1243 between conversions. Figure 6 shows a plot of average supply current vs. conversion rate. Because the MAX1243 uses an external reference voltage (assumed to be present continuously), it "wakes up" from shutdown more quickly, providing lower average supply currents. The wakeup time, tWAKE, is the time from SHDN deasserted to the time when a conversion may be initiated (Figure 5). For the MAX1242, this time depends on the time in shutdown (Figure 7) because the external 4.7F reference bypass capacitor loses charge slowly during shutdown. The MAX1243's wake-up time is largely dependent on the external reference's power-up time. If the external reference is not shut down, the wake-up time is approximately 4s. COMPLETE CONVERSION SEQUENCE CS tWAKE SHDN DOUT CONVERSION 0 CONVERSION 1 POWERED UP POWERED DOWN POWERED UP Figure 5. Shutdown Sequence POWER-UP DELAY (ms) 0.8 CODE = 0101010100 MAX1242 VDD = 5V 100 MAX1242 VDD = 3V 10 MAX1242/43-07 VDD = VREF RLOAD = , CLOAD = 50pF 1000 1.0 MAX1243-fig06 10,000 SUPPLY CURRENT (A) MAX1242/MAX1243 +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 0.6 0.4 0.2 MAX1243 VDD = 3V 1 0.1 1 10 100 1k 10k 100k CONVERSIONS/SEC Figure 6. Average Supply Current vs. Conversion Rate 8 0.0 0.001 0.01 0.1 1 10 TIME IN SHUTDOWN (sec) Figure 7. Typical Reference-Buffer Power-Up Delay vs. Time in Shutdown _______________________________________________________________________________________ +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 MAX1242/MAX1243 CS 1 4 8 12 16 SCLK DOUT B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 S1 S0 EOC INTERFACE IDLE CONVERSION IN PROGRESS TRACK/HOLD TRACK STATE HOLD SUB BITS CLOCK OUT SERIAL DATA EOC TRAILING ZEROS IDLE TRACK 7.5s (tCONV) HOLD 12.5 x 0.476s = 5.95s 0s CYCLE TIME 0.24s 0s (tCS) TOTAL = 13.7s Figure 8a. Interface Timing Sequence CS 1 4 8 SCLK DOUT B9 B8 B7 B6 B5 B4 B3 B2 B1 B0 EOC INTERFACE IDLE CONVERSION IN PROGRESS TRACK/HOLD TRACK STATE HOLD 7.5s (tCONV) CLOCK OUT SERIAL DATA EOC IDLE TRACK HOLD 0.24s 10.5 x 0.476s = 5s 0s CYCLE TIME (tCS) TOTAL = 12.74s Figure 8b. Interface Timing Sequence--Minimum Cycle Time tCS CS ... tCS0 tCH ... SCLK tDO tDV tCONV ... DOUT tAP INTERNAL T/H (TRACK/ACQUIRE) tCL B0 tTR S1 S0 tSTR (HOLD) ... (TRACK/ACQUIRE) Figure 9. Detailed Serial-Interface Timing _______________________________________________________________________________________ 9 MAX1242/MAX1243 +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 External Clock The actual conversion does not require the external clock. This allows the conversion result to be read back at the P's convenience at any clock rate up to 2.1MHz. The clock duty cycle is unrestricted if each clock phase is at least 200ns. Do not run the clock while a conversion is in progress. OUTPUT CODE FULL-SCALE TRANSITION 11...111 11...110 11...101 Timing and Control Conversion-start and data-read operations are controlled by the CS and SCLK digital inputs. The timing diagrams of Figures 8 and 9 outline serial-interface operation. A CS falling edge initiates a conversion sequence: the T/H stage holds the input voltage, the ADC begins to convert, and DOUT changes from high impedance to logic low. SCLK must be kept low during the conversion. An internal register stores the data when the conversion is in progress. EOC is signaled by DOUT going high. DOUT's rising edge can be used as a framing signal. SCLK shifts the data out of this register any time after the conversion is complete. DOUT transitions on SCLK's falling edge. The next falling clock edge produces the MSB of the conversion at DOUT, followed by the remaining bits. Since there are 10 data bits, two sub-bits, and one leading high bit, at least 13 falling clock edges are needed to shift out these bits. Extra clock pulses occurring after the conversion result has been clocked out, and prior to a rising edge of CS, produce trailing zeros at DOUT and have no effect on converter operation. FS = VREF - 1LSB V 1LSB = REF 1024 00...011 00...010 00...001 00...000 0 1 FS FS - 3/2LSB Figure 10. Unipolar Transfer Function, Full Scale (FS) = VREF - 1LSB, Zero Scale (ZS) = GND I/O CS SCK SCLK MISO DOUT +3V MAX1242 MAX1243 SS a) SPI For minimum cycle time, use DOUT's rising edge as the EOC signal and then clock out the data with 10.5 clock cycles at full speed (Figure 8b). Pull CS high after reading the conversion's LSB. After the specified minimum time, tCS, pull CS low again to initiate the next conversion. CS CS SCK SCLK MISO DOUT +3V Output Coding and Transfer Function The data output from the MAX1242/MAX1243 is binary. Figure 10 depicts the nominal transfer function. Code transitions occur halfway between successive-integer LSB values. If VREF = 2.5V, then 1LSB = 2.44mV or 2.5V / 1024. 2 3 INPUT VOLTAGE (LSB) MAX1242 MAX1243 SS b) QSPI __________Applications Information I/O CS SK SCLK SI DOUT Connection to Standard Interfaces The MAX1242/MAX1243 serial interface is fully compatible with SPI, QSPI, and Microwire standard serial interfaces (Figure 11). MAX1242 MAX1243 c) MICROWIRE Figure 11. Common Serial-Interface Connections to the MAX1242/MAX1243 10 ______________________________________________________________________________________ +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 2ND BYTE READ SCLK CS tCONV HIGH-Z D9 DOUT D8 D7 D6 D5 D4 D3 D2 D1 MSB D0 S1 S0 S1 S0 LSB EOC Figure 12. SPI/Microwire Serial-Interface Timing (CPOL = CPHA = 0) SCLK CS tCONV HIGH-Z DOUT D9 D8 D7 D6 MSB D5 D4 D3 D2 D1 D0 LSB EOC Figure 13. QSPI Serial-Interface Timing (CPOL = CPHA = 0) If a serial interface is available, set the CPU's serial interface in master mode so the CPU generates the serial clock. Choose a clock frequency up to 2.1MHz. 1) Use a general-purpose I/O line on the CPU to pull CS low. Keep SCLK low. 2) Wait the maximum conversion time specified before activating SCLK. Alternatively, look for a DOUT rising edge to determine the end of conversion. 3) Activate SCLK for a minimum of 11 clock cycles. The first falling clock edge produces the MSB of the DOUT conversion. DOUT output data transitions on SCLK's falling edge and is available in MSB-first format. Observe the SCLK-to-DOUT valid timing characteristic. Data can be clocked into the P on SCLK's rising edge. 4) Pull CS high at or after the 11th falling clock edge. If CS remains low, the two sub-bits and trailing zeros are clocked out after the LSB. 5) With CS = high, wait the minimum specified time, tCS, before initiating a new conversion by pulling CS low. If a conversion is aborted by pulling CS high before the conversion's end, wait the minimum acquisition time, tACQ, before starting a new conversion. Data can be output in two bytes or continuously, as shown in Figures 8a and 8b. The bytes contain the result of the conversion padded with one leading 1, two sub-bits, and trailing 0s if SCLK is still active with CS kept low. SPI and Microwire When using SPI or QSPI, set CPOL = 0 and CPHA = 0. Conversion begins with a CS falling edge. DOUT goes low, indicating a conversion is in progress. Wait until DOUT goes high or until the maximum specified 7.5s conversion time elapses. Two consecutive 1-byte reads are required to get the full 10+2 bits from the ADC. DOUT output data transitions on SCLK's falling edge and is clocked into the P on SCLK's rising edge. The first byte contains a leading 1, and seven bits of conversion result. The second byte contains the remaining three bits, two sub-bits, and three trailing zeros. See Figure 11 for connections and Figure 12 for timing. QSPI Set CPOL = CPHA = 0. Unlike SPI, which requires two 1-byte reads to acquire the 10 bits of data from the ADC, QSPI allows the minimum number of clock cycles necessary to clock in the data. The MAX1242/MAX1243 require 11 clock cycles from the P to clock out the 10 bits of data. Additional clock cycles clock out the two sub-bits followed by trailing zeros (Figure 13). The maximum clock frequency to ensure compatibility with QSPI is 2.097MHz. Layout and Grounding For best performance, use printed circuit boards. Wirewrap boards are not recommended. Board layout should ensure that digital and analog signal lines are separated from each other. Do not run analog and digital (especially clock) lines parallel to one another, or digital lines underneath the ADC package. ______________________________________________________________________________________ 11 MAX1242/MAX1243 1ST BYTE READ Ordering Information (continued) PINPACKAGE INL (LSB) PART TEMP. RANGE MAX1242AESA -40C to +85C 8 SO 1/2 8 SO 1 MAX1242BESA -40C to +85C MAX1242AMJA -55C to +125C 8 CERDIP* 1/2 MAX1242BMJA -55C to +125C 8 CERDIP* 1 MAX1243ACPA 0C to +70C 8 Plastic DIP 1/2 MAX1243BCPA 0C to +70C 8 Plastic DIP 1 MAX1243ACSA 0C to +70C 8 SO 1/2 MAX1243BCSA 0C to +70C 8 SO 1 MAX1243AEPA -40C to +85C 8 Plastic DIP 1/2 MAX1243BEPA -40C to +85C 8 Plastic DIP 1 MAX1243AESA -40C to +85C 8 SO 1/2 MAX1243BESA -40C to +85C 8 SO 1 MAX1243AMJA -55C to +125C 8 CERDIP* 1/2 MAX1243BMJA -55C to +125C 8 CERDIP* 1 ___________________Chip Information TRANSISTOR COUNT: 2559 SUBSTRATE CONNECTED TO GND *Contact factory for availability and processing to MIL-STD-883. Note: Order the MAX1242A in place of the MAX1242C. Order the MAX1242B in place of the MAX1242D. SOICN.EPS ________________________________________________________Package Information PDIPN.EPS MAX1242/MAX1243 +2.7V to +5.25V, Low-Power, 10-Bit Serial ADCs in SO-8 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 (c) 1998 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products. ENGLISH * ???? * ??? * ??? WHAT'S NEW PRODUCTS SOLUTIONS DESIGN APPNOTES SUPPORT BUY COMPANY MEMBERS M axim > P roduc ts > A nalog-to-Digital C onverters MAX1242, MAX1243 +2.7V to +5.25V, Low-Power, 10-Bit Serial ADC s in SO-8 QuickView Technical Documents Ordering Info More Information All Ordering Information Notes: 1. Other options and links for purchasing parts are listed at: http://www.maxim-ic.com/sales. 2. Didn't Find What You Need? Ask our applications engineers. Expert assistance in finding parts, usually within one business day. 3. Part number suffixes: T or T&R = tape and reel; + = RoHS/lead-free; # = RoHS/lead-exempt. More: SeeFull Data Sheet or Part Naming C onventions. 4. * Some packages have variations, listed on the drawing. "PkgC ode/Variation" tells which variation the product uses. Devices: 1-53 of 53 M AX1242 Fre e Sam ple Buy Pack age : TYPE PINS FOOTPRINT Tem p DRAWING CODE/VAR * RoHS/Le ad-Free ? M aterials Analys is MAX1242AMJA C eramic DIP;8 pin;81 mm Dwg: 21-0045A (PDF) Use pkgcode/variation: J8-2* -55C to +125C RoHS/Lead-Free: See data sheet Materials Analysis MAX1242BMJA C eramic DIP;8 pin;81 mm Dwg: 21-0045A (PDF) Use pkgcode/variation: J8-2* -55C to +125C RoHS/Lead-Free: See data sheet Materials Analysis MAX1242AC PA+ PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8+2* 0C to +70C RoHS/Lead-Free: Lead Free Materials Analysis MAX1242BC PA+ PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8+2* 0C to +70C RoHS/Lead-Free: Lead Free Materials Analysis MAX1242AC PA PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8-2* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1242BC PA PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8-2* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1242BEPA+ PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8+2* -40C to +85C RoHS/Lead-Free: Lead Free Materials Analysis MAX1242BEPA PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8-2* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX1242AEPA+ PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8+2* -40C to +85C RoHS/Lead-Free: Lead Free Materials Analysis MAX1242AEPA PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8-2* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX1242BC SA+ SOIC ;8 pin;31 mm 0C to +70C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1242AC SA+T SOIC ;8 pin;31 mm 0C to +70C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1242BC SA+T SOIC ;8 pin;31 mm 0C to +70C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1242AC SA-T SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1242AC SA SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1242BC SA SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1242BC SA-T SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1242AC SA+ SOIC ;8 pin;31 mm 0C to +70C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1242BESA-T SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX1242BESA SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX1242BESA+ SOIC ;8 pin;31 mm -40C to +85C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1242BESA+T SOIC ;8 pin;31 mm -40C to +85C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1242AESA-T SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* RoHS/Lead-Free: No Materials Analysis MAX1242AESA+T SOIC ;8 pin;31 mm -40C to +85C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1242AESA+ SOIC ;8 pin;31 mm -40C to +85C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1242AESA SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* RoHS/Lead-Free: No Materials Analysis M AX1243 Fre e Sam ple Buy Pack age : TYPE PINS FOOTPRINT -40C to +85C -40C to +85C Tem p DRAWING CODE/VAR * MAX1243AEPA+ -40C to +85C RoHS/Le ad-Free ? M aterials Analys is RoHS/Lead-Free: See data sheet MAX1243BMJA C eramic DIP;8 pin;81 mm Dwg: 21-0045A (PDF) Use pkgcode/variation: J8-2* -55C to +125C RoHS/Lead-Free: No Materials Analysis MAX1243AMJA C eramic DIP;8 pin;81 mm Dwg: 21-0045A (PDF) Use pkgcode/variation: J8-2* -55C to +125C RoHS/Lead-Free: No Materials Analysis MAX1243BC /D RoHS/Lead-Free: See data sheet MAX1243BC PA+ PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8+2* 0C to +70C RoHS/Lead-Free: Lead Free Materials Analysis MAX1243AC PA+ PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8+2* 0C to +70C RoHS/Lead-Free: Lead Free Materials Analysis MAX1243BC PA PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8-2* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1243AC PA PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8-2* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1243BEPA+ PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8+2* -40C to +85C RoHS/Lead-Free: Lead Free Materials Analysis MAX1243BEPA PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8-2* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX1243AEPA PDIP;8 pin;82 mm Dwg: 21-0043D (PDF) Use pkgcode/variation: P8-2* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX1243AC SA+ SOIC ;8 pin;31 mm 0C to +70C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1243AC SA+T SOIC ;8 pin;31 mm 0C to +70C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1243BC SA+ SOIC ;8 pin;31 mm 0C to +70C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1243AC SA-T SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* RoHS/Lead-Free: No Materials Analysis MAX1243BC SA+T SOIC ;8 pin;31 mm 0C to +70C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1243BC SA SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1243BC SA-T SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1243AC SA SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* 0C to +70C RoHS/Lead-Free: No Materials Analysis MAX1243BESA+ SOIC ;8 pin;31 mm -40C to +85C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1243AESA+T SOIC ;8 pin;31 mm -40C to +85C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1243AESA+ SOIC ;8 pin;31 mm -40C to +85C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* RoHS/Lead-Free: Lead Free Materials Analysis MAX1243BESA-T SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX1243AESA SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX1243AESA-T SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX1243BESA SOIC ;8 pin;31 mm Dwg: 21-0041B (PDF) Use pkgcode/variation: S8-5* -40C to +85C RoHS/Lead-Free: No Materials Analysis MAX1243BESA+T SOIC ;8 pin;31 mm -40C to +85C Dwg: 21-0041B (PDF) Use pkgcode/variation: S8+5* 0C to +70C RoHS/Lead-Free: Lead Free Materials Analysis Didn't Find What You Need? Next Day Product Selection Assistance from Applications Engineers Parametric Search Applications Help QuickView Technical Documents Ordering Info More Information Des c ription Key Features A pplic ations /U s es Key Spec ific ations Diagram Data Sheet A pplic ation N otes Des ign Guides E ngineering Journals Reliability Reports Software/M odels E valuation Kits P ric e and A vailability Samples Buy O nline P ac kage I nformation Lead-Free I nformation Related P roduc ts N otes and C omments E valuation Kits Doc ument Ref.: 1 9 -1 1 5 6 ; Rev 2 ; 1 9 9 8 -0 6 -0 1 T his page las t modified: 2 0 0 7 -0 7 -1 9 C ONTAC T US: SEND US AN EMAIL C opyright 2 0 0 7 by M axim I ntegrated P roduc ts , Dallas Semic onduc tor * Legal N otic es * P rivac y P olic y