DIMENSION UNITS
SCALE
MM
3:1
GENERAL TOLERANCES
(UNLESS SPECIFIED)
ANGULAR TOL
±
0.5 °
4 PLACES
±
3 PLACES
±
2 PLACES
±
0.13
1 PLACE
±
0.25
0 PLACES
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
CURRENT REV DESC: MIGRATED TO NX
EC NO: 173912
DRWN:
DVARVARA
2018/03/28
CHK'D:
TELO
2018/04/02
APPR:
TELO
2018/04/02
INITIAL REVISION:
DRWN:
JBINGHAM
2013/04/03
APPR:
JLAURX
2013/04/05
THIRD ANGLE PROJECTION
DRAWING SERIES
C-SIZE
170390
IMPACT 4-PAIR 85-OHM
UNGUIDED MEZZANINE SALES DRAWING
PRODUCT CUSTOMER DRAWING
DOCUMENT NUMBER
DOC TYPE
DOC PART
REVISION
SD-170390-0001
PSD
001
A5
MATERIAL NUMBER CUSTOMER SHEET NUMBER
SEE CHART GENERAL MARKET 1 OF 2
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
FORMAT: master-tb-prod-C
REVISION: H
DATE: 2018/01/18
SYMBOLS
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
DOCUMENT STATUS P1 RELEASE DATE 2018/04/02 13:39:33
C
"D"
"A"
"C"
NOTES:
1. MATERIALS: HOUSING - LIQUID CRYSTAL POLYMER (LCP), GLASS-FILLED, UL94V-0
TERMINALS - HIGH PERFORMANCE COPPER ALLOY
2. FINISH: 30 µINCH MIN SELECTIVE GOLD IN CONTACT AREA, SELECTIVE MATTE TIN
ON PCB TAILS. NICKEL OVERALL.
3. REFER TO MOLEX PRODUCT SPEC PS-170540-999 FOR PERFORMANCE SPECIFICATIONS
AND ADDITIONAL PCB INFORMATION.
4. EACH SIGNAL WAFER CONTAINS 2 COLUMNS OF TERMINALS.
5. SEE CHARTS FOR PACKAGING SPECIFICATIONS.
6. THIS PART CONFORMS TO CLASS B REQUIREMENTS OF COSMETIC
SPECIFICATION PS-45499-002.
7. REFER TO MOLEX SALES DRAWING SD-170335-0001 FOR
THE MATING HEADERS.
8. REFER TO MOLEX PCB ROUTING GUIDE AS-76060-990 FOR
ANTIPAD AND ROUTING RECOMMENDATIONS.
9. MARKING: LOCATED APPROXIMATELY AS SHOWN
PART NUMBER & DATE CODE
10. GROUND PATHS ARE NOT DISCRETE CIRCUITS WITHIN CONNECTOR
DUE TO PRESENCE OF PLUS CLIP.
11. PART NUMBER 170390-1030 SHOWN ON DRAWING. KEYING FEATURES
WILL CHANGE WITH COLUMN SIZE.
12. THESE DIMENSIONS REPRESENT THE AREA NEEDED TO ACCOMODATE
CONNECTOR INSERTION AND REPAIR ON THE PCB. THIS IS REFERRED
TO AS THE "CONNECTOR KEEP OUT ZONE" AND DOES NOT REPRESENT
THE ACTUAL PERIMETER OF THE CONNECTOR.
20.15 14.85
2.65
11X
1.35
B
1.90
ROW M
ROW L
ROW K
ROW J
ROW H
ROW G
ROW F
ROW E
ROW D
ROW C
ROW B
ROW A
GROUND HOLE
REF
SIGNAL HOLES
REF
PIN A1
"KEEP-OUT ZONE"
SEE NOTE 12
VERTICAL RECEPTACLE HOLE PATTERN
(CONNECTOR SIDE)
PIN A1
SEE NOTE 9
H
STACK HEIGHT
0.80
MIN
1.25
MIN
0.39
⌖
⌀
0.10
(12 HOLES
PER COLUMN)
±
0.05
⌀
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
A A
B B
C C
D D
E E
F F
G G
H H
THIS DRAWING CONTAINS INFORMATION THAT IS PROPRIETARY TO MOLEX ELECTRONIC TECHNOLOGIES, LLC AND SHOULD NOT BE USED WITHOUT WRITTEN PERMISSION
CURRENT REV DESC: MIGRATED TO NX
EC NO: 173912
DRWN:
DVARVARA
2018/03/28
CHK'D:
TELO
2018/04/02
APPR:
TELO
2018/04/02
INITIAL REVISION:
DRWN:
JBINGHAM
2013/04/03
APPR:
JLAURX
2013/04/05
THIRD ANGLE PROJECTION
DRAWING SERIES
C-SIZE
170390
IMPACT 4-PAIR 85-OHM
UNGUIDED MEZZANINE SALES DRAWING
PRODUCT CUSTOMER DRAWING
DOCUMENT NUMBER
DOC TYPE
DOC PART
REVISION
SD-170390-0001
PSD
001
A5
MATERIAL NUMBER CUSTOMER SHEET NUMBER
SEE CHART GENERAL MARKET 2 OF 2
DIMENSION UNITS
SCALE
MM
3:1
GENERAL TOLERANCES
(UNLESS SPECIFIED)
ANGULAR TOL
±
0.5 °
4 PLACES
±
3 PLACES
±
2 PLACES
±
0.13
1 PLACE
±
0.25
0 PLACES
±
DRAFT WHERE APPLICABLE
MUST REMAIN
WITHIN DIMENSIONS
FORMAT: master-tb-prod-C
REVISION: H
DATE: 2018/01/18
SYMBOLS
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
=
0
DOCUMENT STATUS P1 RELEASE DATE 2018/04/02 13:39:33
C
MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIRS DIM "A"
MAX DIM "B" DIM "C" DIM "D" PACKAGING SPEC
18mm STACK
HEIGHT (DIM H)
170390-1008 8 32 15.1 13.3
15.36 19.41 PK-70873-4001
170390-1000 10 40 18.9 17.1
170390-1002 12 48 22.7 20.9
170390-1007 14 56 26.5 24.7
170390-1006 16 64 30.3 28.5
170390-1009 18 72 34.1 32.3
MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIRS DIM "A"
MAX DIM "B" DIM "C" DIM "D" PACKAGING SPEC
25mm STACK
HEIGHT (DIM H)
170390-1028 8 32 15.1 13.3
22.36 19.41 PK-70873-4002
170390-1020 10 40 18.9 17.1
170390-1022 12 48 22.7 20.9
170390-1027 14 56 26.5 24.7
170390-1026 16 64 30.3 28.5
170390-1029 18 72 34.1 32.3
MATERIAL NUMBER # OF COLUMNS # OF DIFF PAIRS DIM "A"
MAX DIM "B" DIM "C" DIM "D" PACKAGING SPEC
37mm STACK
HEIGHT (DIM H)
170390-1038 8 32 15.1 13.3
34.36 20.65 PK-70873-0044
170390-1030 10 40 18.9 17.1
170390-1032 12 48 22.7 20.9
170390-1037 14 56 26.5 24.7
170390-1036 16 64 30.3 28.5
170390-1039 18 72 34.1 32.3
PART NUMBER CHART
0.35
OFFSET BETWEEN MALE
AND FEMALE HOLE PATTERNS
PART NUMBER LOGIC
170390-103*
MODULE AND TAIL PLATING TYPE
1 = UNGUIDED, MATTE TIN
KEY ORIENTATION
0 = UNGUIDED
STACK HEIGHT (H)
0 = 18mm
2 = 25mm
3 = 37mm
# OF COLUMNS
0 = 10 COL
2 = 12 COL
6 = 16 COL
7 = 14 COL
8 = 8 COL
9 = 18 COL
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
A A
B B
C C
D D
E E
F F
G G
H H
