AT27BV010 Features * * * * * * * * * * Fast Read Access Time - 70 ns Dual Voltage Range Operation Unregulated Battery Power Supply Range, 2.7V to 3.6V or Standard 5V 10% Supply Range Compatible with JEDEC Standard AT27C010 Low Power CMOS Operation 20 A max. (less than 1 A typical) Standby for VCC = 3.6V 29 mW max. Active at 5 MHz for VCC = 3.6V JEDEC Standard Packages 32-Lead PLCC 32-Lead TSOP High Reliability CMOS Technology 2,000V ESD Protection 200 mA Latchup Immunity Rapid Programming Algorithm - 100 s/byte (typical) CMOS and TTL Compatible Inputs and Outputs JEDEC Standard for LVTTL and LVBO Integrated Product Identification Code Commercial and Industrial Temperature Ranges 1 Megabit (128K x 8) Unregulated Battery-Voltage OTP CMOS EPROM Description The AT27BV010 is a high performance, low power, low voltage 1,048,576 bit onetime programmable read only memory (OTP EPROM) organized as 128K by 8 bits. It requires only one supply in the range of 2.7V to 3.6V in normal read mode operation, making it ideal for fast, portable systems using either regulated or unregulated battery power. Atmel's innovative design techniques provide fast speeds that rival 5V parts while keeping the low power consumption of a 3V supply. At VCC = 2.7V, any byte can be accessed in less than 70 ns. With a typical power draw of only 18 mW at 5 MHz and VCC = 3V, the AT27BV010 consumes less than one fifth the power of a standard 5V (continued) Pin Configurations Pin Name Function A0 - A16 Addresses O0 - O7 Outputs CE Chip Enable OE Output Enable PGM Program Strobe NC No Connect AT27BV010 TSOP Top View PLCC Top View Type 1 0344E 3-23 Description (Continued) System Considerations EPROM. Standby mode supply current is typically less than 1 A at 3V. The AT27BV010 simplifies system design and stretches battery lifetime even further by eliminating the need for power supply regulation. Switching between active and standby conditions via the Chip Enable pin may produce transient voltage excursions. Unless accommodated by the system design, these transients may exceed data sheet limits, resulting in device non-conformance. At a minimum, a 0.1 F high frequency, low inherent inductance, ceramic capacitor should be utilized for each device. This capacitor should be connected between the VCC and Ground terminals of the device, as close to the device as possible. Additionally, to stabilize the supply voltage level on printed circuit boards with large EPROM arrays, a 4.7 F bulk electrolytic capacitor should be utilized, again connected between the VCC and Ground terminals. This capacitor should be positioned as close as possible to the point where the power supply is connected to the array. The AT27BV010 is available in industry standard JEDECapproved one-time programmable (OTP) plastic PLCC and TSOP packages. All devices feature two-line control (CE, OE) to give designers the flexibility to prevent bus contention. The AT27BV010 operating with VCC at 3.0V produces TTL level outputs that are compatible with standard TTL logic devices operating at VCC = 5.0V. At VCC = 2.7V, the part is compatible with JEDEC approved low voltage battery operation (LVBO) interface specifications. The device is also capable of standard 5-volt operation making it ideally suited for dual supply range systems or card products that are pluggable in both 3-volt and 5-volt hosts. Atmel's AT27BV010 has additional features to ensure high quality and efficient production use. The Rapid Programming Algorithm reduces the time required to program the part and guarantees reliable programming. Programming time is typically only 100 s/byte. The Integrated Product Identification Code electronically identifies the device and manufacturer. This feature is used by industry standard programming equipment to select the proper programming algorithms and voltages. The AT27BV010 programs exactly the same way as a standard 5V AT27C010 and uses the same programming equipment. 3-24 AT27BV010 AT27BV010 Absolute Maximum Ratings* Block Diagram Temperature Under Bias .................. -40C to +85C Storage Temperature...................... -65C to +125C Voltage on Any Pin with Respect to Ground......................... -2.0V to +7.0V (1) Voltage on A9 with Respect to Ground ...................... -2.0V to +14.0V (1) VPP Supply Voltage with Respect to Ground....................... -2.0V to +14.0V (1) *NOTICE: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Note: 1. Minimum voltage is -0.6V dc which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC + 0.75V dc which may be exceeded if certain precautions are observed (consult application notes) and which may overshoot to +7.0V for pulses of less than 20 ns. Operating Modes CE Mode \ Pin Read (2) VIL Output Disable Standby (2) PGM Verify X VIH Rapid Program PGM (2) (3) (3) Inhibit (3) VIL VIL VIH OE PGM VIL X VIH X X X VIH VIL (1) VIL VIH X X Ai VPP Ai X X X X X Ai VPP Ai VPP X VPP VCC Outputs VCC (2) DOUT VCC (2) High Z VCC (2) High Z VCC (3) DIN VCC (3) DOUT VCC (3) High Z (4) Product Identification (3, 5) VIL VIL Notes: 1. X can be VIL or VIH. 2. Read, output disable, and standby modes require, 2.7V VCC 3.6V, or 4.5V VCC 5.5V. 3. Refer to Programming Characteristics. Programming modes require VCC = 6.5V. X A9 = VH A0 = VIH or VIL A1 - A16 = VIL X VCC (3) Identification Code 4. VH = 12.0 0.5V. 5. Two identifier bytes may be selected. All Ai inputs are held low (VIL), except A9 which is set to VH and A0 which is toggled low (VIL) to select the Manufacturer's Identification byte and high (VIH) to select the Device Code byte. 3-25 DC and AC Operating Conditions for Read Operation AT27BV010 -70 Operating Temperature (Case) Com. Ind. VCC Power Supply -90 -12 -15 0C - 70C 0C - 70C 0C - 70C 0C - 70C -40C - 85C -40C - 85C -40C - 85C -40C - 85C 2.7V to 3.6V 2.7V to 3.6V 2.7V to 3.6V 2.7V to 3.6V 5V 10% 5V 10% 5V 10% 5V 10% = Preliminary Information DC and Operating Characteristics for Read Operation Symbol Parameter Condition Min Max Units VCC = 2.7V to 3.6V ILI ILO IPP1 (2) Input Load Current VIN = 0V to VCC 1 A Output Leakage Current VOUT = 0V to VCC 5 A VPP = VCC 10 A ISB1 (CMOS), CE = VCC 0.3V 20 A ISB2 (TTL), CE = 2.0 to VCC + 0.5V 100 A 8 mA VPP (1) Read/Standby Current VCC (1) Standby Current ISB ICC VCC Active Current VIL Input Low Voltage VIH Input High Voltage VOL Output Low Voltage VOH Output High Voltage f = 5 MHz, IOUT = 0 mA, CE = VIL, VCC = 3.6V VCC = 3.0 to 3.6V -0.6 0.8 V VCC = 2.7 to 3.6V -0.6 0.2 x VCC V VCC = 3.0 to 3.6V 2.0 VCC + 0.5 V 0.7 x VCC VCC + 0.5 V VCC = 2.7 to 3.6V IOL = 2.0 mA 0.4 V IOL = 100 A 0.2 V IOL = 20 A 0.1 V IOH = -2.0 mA 2.4 V IOH = -100 A VCC - 0.2 V IOH = -20 A VCC - 0.1 V VCC = 4.5V to 5.5V ILI ILO IPP1 (2) Input Load Current VIN = 0V to VCC 1 A Output Leakage Current VOUT = 0V to VCC 5 A VPP = VCC 10 A ISB1 (CMOS), CE = VCC 0.3V 100 A ISB2 (TTL), CE = 2.0 to VCC + 0.5V 1 mA f = 5 MHz, IOUT = 0 mA, CE = VIL 25 mA VPP (1) Read/Standby Current ISB VCC (1) Standby Current ICC VCC Active Current VIL Input Low Voltage -0.6 0.8 V VIH Input High Voltage 2.0 VCC + 0.5 V VOL Output Low Voltage IOL = 2.1 mA 0.4 V VOH Output High Voltage IOH = -400 A Notes: 1. VCC must be applied simultaneously with or before VPP, and removed simultaneously with or after VPP. 3-26 AT27BV010 2.4 V 2. VPP may be connected directly to VCC, except during pro gramming. The supply current would then be the sum of ICC and IPP. AT27BV010 AC Characteristics for Read Operation (VCC = 2.7V to 3.6V and 4.5V to 5.5V) AT27BV010 -70 Symbol tACC (3) Parameter Condition Min Max -90 Min Max -12 Min -15 Max Min Max Units Address to Output Delay CE = OE = VIL 70 90 120 150 ns tCE (2) CE to Output Delay OE = VIL 70 90 120 150 ns tOE (2, 3) OE to Output Delay CE = VIL 50 50 50 60 ns tDF (4, 5) OE or CE High to Output Float, whichever occurred first 40 40 40 50 ns tOH Notes: Output Hold from Address, CE or OE, whichever occurred first 0 2, 3, 4, 5. - see AC Waveforms for Read Operation. AC Waveforms for Read Operation 0 0 0 ns = Preliminary Information (1) Notes: 1. Timing measurement references are 0.8V and 2.0V. Input AC drive levels are 0.45V and 2.4V, unless otherwise specified. 2. OE may be delayed up to tCE - tOE after the falling edge of CE without impact on tCE . 3. OE may be delayed up to tACC - tOE after the address is valid without impact on tACC . 4. This parameter is only sampled and is not 100% tested. 5. Output float is defined as the point when data is no longer driven. 3-27 Output Test Load Input Test Waveform and Measurement Level tR, tF < 20 ns (10% to 90%) Note: CL = 100 pF including jig capacitance. Pin Capacitance (f = 1 MHz, T = 25C) (1) Typ Max Units CIN 4 8 pF VIN = 0V COUT 8 12 pF VOUT = 0V Note: 3-28 Conditions 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27BV010 AT27BV010 Programming Waveforms (1) Notes: 1. The Input Timing Reference is 0.8V for VIL and 2.0V for VIH. 2. tOE and tDFP are characteristics of the device but must be accommodated by the programmer. 3. When programming the AT27BV010, a 0.1 F capacitor is required across VPP and ground to suppress spurious voltage transients. DC Programming Characteristics TA = 25 5C, VCC = 6.5 0.25V, VPP = 13.0 0.25V Symbol Parameter Test Conditions ILI Input Load Current VIN = VIL, VIH VIL Input Low Level VIH Input High Level VOL Output Low Voltage IOL = 2.1 mA VOH Output High Voltage IOH = -400 A ICC2 IPP2 VCC Supply Current (Program and Verify) VPP Supply Current VID A9 Product Identification Voltage Limits Min Max Units 10 A -0.6 0.8 V 2.0 VCC + 1 V 0.4 V 2.4 CE = PGM = VIL 11.5 V 40 mA 20 mA 12.5 V 3-29 AC Programming Characteristics Rapid Programming Algorithm TA = 25 5C, VCC = 6.5 0.25V, VPP = 13.0 0.2V A 100 s PGM pulse width is used to program. The address is set to the first location. VCC is raised to 6.5V and VPP is raised to 13.0V. Each address is first programmed with one 100 s PGM pulse without verification. Then a verification / reprogramming loop is executed for each address. In the event a byte fails to pass verification, up to 10 successive 100 s pulses are applied with a verification after each pulse. If the byte fails to verify after 10 pulses have been applied, the part is considered failed. After the byte verifies properly, the next address is selected until all have been checked. VPP is then lowered to 5.0V and VCC to 5.0V. All bytes are read again and compared with the original data to determine if the device passes or fails. Test Conditions* (1) Symbol Parameter Limits Min Max Units tAS Address Setup Time 2 s tCES CE Setup Time 2 s tOES 2 s tDS OE Setup Time Data Setup Time 2 s tAH Address Hold Time 0 s tDH 2 s 2 s tVCS Data Hold Time OE High to Output Float Delay (2) VPP Setup Time VCC Setup Time 2 s tPW PGM Program Pulse Width (3) 95 tOE Data Valid from OE tPRT VPP Pulse Rise Time During Programming tDFP tVPS 0 130 ns 105 s 150 ns 50 ns *AC Conditions of Test: Input Rise and Fall Times (10% to 90%)...............20 ns Input Pulse Levels....................................0.45V to 2.4V Input Timing Reference Level....................0.8V to 2.0V Output Timing Reference Level.................0.8V to 2.0V Notes: 1. VCC must be applied simultaneously or before VPP and removed simultaneously or after VPP. 2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven --see timing diagram. 3. Program Pulse width tolerance is 100 sec 5%. Atmel's 27BV010 Integrated (1) Product Identification Code Pins Codes Manufacturer Device Type Note: 3-30 A0 O7 O6 O5 O4 O3 O2 O1 O0 0 1 0 0 0 0 0 0 1 0 1 0 1 1 1 0 0 1 Hex Data 1E 05 1. The AT27BV010 has the same Product Identification Code as the AT27C010. Both are programming compatible. AT27BV010 AT27BV010 Ordering Information tACC (ns) 70 90 120 150 ICC (mA) VCC = 3.6V Ordering Code Package 0.02 AT27BV010-70JC AT27BV010-70TC 32J 32T Commercial (0C to 70C) 8 0.02 AT27BV010-70JI AT27BV010-70TI 32J 32T Industrial (-40C to 85C) 8 0.02 AT27BV010-90JC AT27BV010-90TC 32J 32T Commercial (0C to 70C) 8 0.02 AT27BV010-90JI AT27BV010-90TI 32J 32T Industrial (-40C to 85C) 8 0.02 AT27BV010-12JC AT27BV010-12TC 32J 32T Commercial (0C to 70C) 8 0.02 AT27BV010-12JI AT27BV010-12TI 32J 32T Industrial (-40C to 85C) 8 0.02 AT27BV010-15JC AT27BV010-15TC 32J 32T Commercial (0C to 70C) 8 0.02 AT27BV010-15JI AT27BV010-15TI 32J 32T Industrial (-40C to 85C) Active Standby 8 Operation Range = Preliminary Information Package Type 32J 32 Lead, Plastic J-Leaded Chip Carrier (PLCC) 32T 32 Lead, Plastic Thin Small Outline Package (TSOP) 3-31