1
SLiC
Aerial Closure with Spiral
End Seals and Bond Assembly
Instructions
November 1997
34-7039-8133-1-D
2
Contents:
1.0 General ........................................................................................................................................................ 3
2.0 Kit Contents...................................................................................................................................................4
3.0 Cable Preparation .........................................................................................................................................4
4.0 Closure Installation, Bonding and Splicing ................................................................................................... 5
5.0 End Seal Installation .....................................................................................................................................6
6.0 Closure Assembly .........................................................................................................................................8
7.0 Extending Closure.........................................................................................................................................8
8.0 Accessories...................................................................................................................................................8
Cut with scissors
3
Maximum
Splice
Opening
Maximum
Bundle
Diameter
Approx. Cable
Range Pair
Count
SLiC
3 x 33 BA
21"
(533 mm)
3.6"
(91.4 mm)
*400 pair
26 or 24 AWG
(0.4 or 0.5 mm)
SLiC
5 x 33 BA
21"
(533 mm)
5.6"
(142.2 mm)
*1200 pair
26 AWG
(0.4 mm)
SLiC
9 x 36 BA
25"
(635 mm)
9.6"
(244 mm)
*3600 pair
26 AWG
(0.4 mm)
21"
(533 mm)
7.6"
(193.0 mm)
*2400 pair
26 AWG
(0.4 mm)
SLiC
2 x 29 BA
17"
(432 mm)
2.6"
(66 mm)
**200 pair
26 or 24 AWG
(0.4 or 0.5 mm)
SLiC
2 x 19 BA
14"
(356 mm)
2.2"
(55.9 mm)
100 pair
26 or 24 AWG
(0.4 or 0.5 mm)
SLiC
7 x 33 BA
1.0 General
1.01 This instruction bulletin describes the assembly of the 3M™ SLiCTM Aerial Closure with Spiral End Seals and
Bond Assembly with external bonding hanger brackets. The closures are free breathing and suitable for
straight, butt, and branch splices of non-pressurized communication cables.
** BASED ON MORE THAN ONE CABLE
* BASED ON 2-BANK STRAIGHT SPLICE USING 4000-DWP MODULE
7" End Seal5" End Seal3" End Seal2" End Seal
1.02 End Seal Port Diameter Range:
End Seal SLiC 2x19* SLiC 3x33 SLiC 5x33 SLiC 7x33
Port Diameter Range SLiC 2x29* SLiC 9x36
Port #1 0.8 to 1.6" 0.8 to 2.6" 1.2 to 3.0" 1.5 to 3.8"
20 to 41 mm 20 to 66 mm 30 to 76 mm 38 to 97 mm
Port #2 0.5 to 1.0" 0.5 to 1.0" 0.8 to 1.4" 1.2 to 1.8"
13 to 25 mm 13 to 25 mm 20 to 36 mm 30 to 46 mm
Port #3 **0.5 to 1.0" 0.5 to 1.0" 1.4 to 2.0" 0.5 to 1.2"
13 to 25 mm 13 to 25 mm 36 to 51 mm 13 to 30 mm
Port #4 NA NA 0.5 to 1.2" 1.8" to 2.4"
13 to 30 mm 46 to 61 mm
Port #5 NA NA NA 0.5 to 1.2"
13 to 30 mm
Between Wraps 0.2 to 0.4" 0.2 to 0.4" 0.2 to 0.4" 0.2 to 0.4"
5.1 to 10.2 mm 5.1 to 10.2 mm 5.1 to 10.2 mm 5.1 to 10.2 mm
* Total of all cable diameters cannot exceed 1.6" (41 mm) for the 2" SLiCs.
** The third port on the 2" endseal is labeled Port 2.
4
1/2" (13 mm)
Core Wrap
1/2" (13 mm)
1/8"
(3 mm)
Inner Sheath
Core Wrap
3.02 Double sheath cable.
3.0 Cable Preparation
Note: For both single and double sheath cables, cut
shield flush with outer sheath.
3.01 Single sheath cable.
1.03 Dimensions: A
B
C
A
Size B C
2 x 19 19" (483 mm ) 5.3" (135 mm) 3.2" (80 mm)
2 x 29 29" (737 mm) 5.9" (150 mm) 3.2" (80 mm)
3 x 33 33" (838 mm) 7.1" (180 mm) 4.7" (119 mm)
5 x 33 33" (838 mm) 9.2" (234 mm) 6.8" (173 mm)
7 x 33 33" (838 mm) 11.5" (292 mm) 8.9" (227 mm)
9 x 36 36" (914 mm) 13.5" (343 mm) 10.9" (276 mm)
2.0 Kit Contents
2.01 Kit Contents are as follows:
Closure Body with:
Bond Bar
Braid Assembly
Spiral End Seals
2.02 Additional Materials Required:
Shield Connectors
Cable Ties
Cable Spacers
Moisture Resistant Splicing Connectors
Vinyl tape Closure BodyEnd Seal (2) Bond Assembly (2)
Bond Bar
5
Note: On cables less than 3/4" (19 mm) in diameter,
cut a 1 1/2" (38 mm) slit in the sheath opposite
connector location. Then complete procedure.
1 1/2"
(38 mm) Slit
1" (25 mm)
Slit
3.03 Make a 1" (25 mm) slit in the outer sheath and shield.
Lift corners for base insertion.
4.0 Closure Installation, Bonding and Splicing
4.01 Attach closure to strand using the proper position at the
bottom of the external bond hanger bracket.
Note: Always use bottom notch with small groove. For 10M
strand and larger, rotate hanger cap and use large
groove. Secure the hanger brackets to strand using
50 in•lbs (565 cm•N) torque. For self-supporting cable,
tighten to 75 in•lbs (850 cm•N) torque.
Lashed cable support and spacer (use appropriate size
of cable spacer to keep cable at the same level or
slightly lower that the end seal openings)
** X See table in Section 1.0
Trim Core Wrap to extend approximately 1"
(25mm) past the outer sheath. If core wrap is
damaged, wrap with vinyl tape.
Slit web approximately 91" (2.3 m) on self-supporting cable
48"
(1219mm)
6
5.0 End Seal Installation
5.01 Remove plugs for the desired number of cables to be
installed.
Note: Use appropriate port as needed for cable size
to be installed (Check cable range shown on
end seal.)
4.02 Remove connector base from bond assembly and insert it
between shield and core wrap; inner sheath for double sheath
cable, until stops meet outer sheath.
4.03 Place terminal wrench over stud and push down to bend
corners and pull slit together.
4.04 Attach bond assembly over stud and tighten firmly with
securing nut.
Note: Tail of base must contact connector top.
5.02 Install end seal on cable and put one wrap of vinyl
tape around center of end seal.
7
5.03 Cut on dotted line, if necessary, according to the following
chart: 2x19 3x33 5x33 7x33
SLiC 2x29 9x36
If end seal diameter is 2.5" 3.8" 5.8" 7.4"
greater than: 64 mm 99 mm 147 mm 188 mm
Note: Cut method and location indicated by dotted line
on each End Seal.
Note: Dotted line configuration on largest end seal is
different than others due end seal thickness.
5.04 End seal cutting is optional, but makes closing of closure
easier with larger diameter cable. If end seal is not cut, then
compress SLiC end by using a knife to slit through thin
plastic membrane.
Then place a heavy duty cable tie, hose clamps or metal
banding through the slit on each end and tighten to secure
and compress seal.
5.05 For sheath repair of cables larger than maximum diameter
as indicated on end seal, cut tail until end seal diameter is
approximately 0.3" to 0.5" (8 mm to 13 mm) greater than
diameter of SLiC; i.e., the SLiC 3x33 should have a
maximum end seal diameter in the range of 3.3" to 3.5"
(84 mm to 89 mm).
Note: Location of end seal in SLiC is not flush with end.
Distance required between end seals shown below.
Distance Between End
SLiC Seal Centers
2x19 16" (406 mm)
2x29 25" (635 mm)
3x33 29" (737 mm)
5x33 29" (737 mm)
7x33 29" (737 mm)
9x36 32" (813 mm)
8
Telecom Systems Division
6801 River Place Blvd.
Austin, TX 78726-9000
800/426-8688
Litho in USA
© 3M 1997 34-7039-8133-1-D
Important Notice
All statements, technical information and recommendations related to the Seller's products are based on information believed to be reliable,
but the accuracy or completeness thereof is not guaranteed. Before utilizing the product, the user should determine the suitability of the
product for its intended use. The user assumes all risks and liability whatsoever in connection with such use.
Any statements or recommendations of the Seller which are not contained in the Seller's current publications shall have no force or effect
unless contained in an agreement signed by an authorized officer of the Seller. The statements contained herein are made in lieu of all
warranties, express or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose which
warranties are hereby expressly disclaimed.
SELLER SHALL NOT BE LIABLE TO THE USER OR ANY OTHER PERSON UNDER ANY LEGAL THEORY, INCLUDING BUT NOT
LIMITED TO NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR ANY DIRECT OR CONSEQUENTIAL DAMAGES
SUSTAINED OR INCURRED BY REASON OF THE USE OF ANY OF THE SELLER'S PRODUCTS THAT WERE DEFECTIVE.
Note: White cable ties used for clarity only.
6.0 Closure Assembly
6.01 Tie splice bundle and cable ends to bond bar.
6.02 Close latches to seal assembly.
Printed on 50% recycled paper
with 10% post consumer
7.0 Extending Closure
7.01 Remove bond bar with tubing from a second closure
and cut off 6" (152 mm).
7.02 Cut second closure in half using center mark as a guide.
Note: Each half section will only fit over similar end of
main closure body.
7.03 Install 6" (152 mm) bond bar with cover tubing on
closure half.
Note: Use piece of braid from half section and attach to
braid from main closure body or cut new braid to
reach full length of extended closure.
7.04 Install half section over end of main body.
7.05 Tie cable to 6" (152 mm) bond bar.
7.06 Reposition end seal in extended body, close latches to seal.
Note: 2 x 19 and 9 x 36 BA Closures cannot be extended.
8.0 Accessories
8.01 • AC-HB1 Aerial Closure Offset Hanger Brackets
• AC-HB2 Extended Hanger Brackets
Designed to support and bond the SLiC Closures
to the messenger strand when more than one
cable is supported by the messenger.
Cap and Bolt
AC-HB1
AC-HB2
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
3M:
SLIC-5-BSW SLIC-2.2X19 SLIC-2.2X19-4460S SLIC-2.2X19-BA SLIC-2.2X19-BA/SES SLIC-2.2X19-SES SLIC-
2.2X19-SR/SES SLIC-2.6X29 SLIC-2.6X29-4460S SLIC-2.6X29-BA SLIC-2.6X29-BA/SES SLIC-2.6X29-SES SLIC-
2.6X29-SR/SES SLIC-2-SES SLIC-3.6X19-BA/SES SLIC-3.6X19-FB SLIC-3.6X19-SES SLIC-3.6X33 SLIC-3.6X33-
4460S SLIC-3.6X33-BA SLIC-3.6X33-BA/SES SLIC-3.6X33-SR/RES SLIC-3.6X33-SR/SES SLIC-3-SES SLIC-
5.6X33 SLIC-5.6X33-4460S SLIC-5.6X33-BA SLIC-5.6X33-BA/SES SLIC-5.6X33-SR/RES SLIC-5.6X33-SR/SES
SLIC-5-SES SLIC-7.6X33 SLIC-7.6X33-4460S SLIC-7.6X33-BA SLIC-7.6X33-BA/SES SLIC-7.6X33-SES SLIC-
7.6X33-SR/SES SLIC-7-SES SLIC-9.6X36 SLIC-9.6X36-BA SLIC-9.6X36-BA/SES SLIC-9.6X36-SES SLIC-9.6X36-
SR/SES SLIC-3.6X33-SES SLIC-5.6X33-SES SLIC3900-A