STD01NY - Sanken Electric Co., Ltd.

STD01N and STD01P

Description

The STD01N and STD01P are enhanced Darlington transistors

with built-in drivers and temperature compensation diode.

Manufactured using the unique Sanken thin-wafer production

technology, these devices achieve higher power levels through

decreased thermal resistance, and can withstand higher voltages

than similar devices on the market.

The temperature compensation diode is integrated on the same

chip as the power transistors. By this design, the STD01N and

STD01P eliminate delays that would otherwise be induced

between thermal sensing at the heat source, and the operation of

the compensation circuitry. Thus, these transistors are ideal for

applications where enhanced thermal stability is required.

This device is provided in a 5-pin TO-3P plastic package with

pin 4 removed. Contact Sanken™ for application support and

additional information on device performance.

Applications include:

▪ General amplifier applications

▪ Professional audio amplifiers

▪ Car audio amplifiers

Features and Benefits

▪ Built-in temperature compensation diodes

▪ High power (100 W) handling in a small package

(TO-3P), for minimized heat sink requirements

▪ Built-in drivers and temperature compensation diodes,

reducing external component count and simplifying

circuit design

▪ NPN and PNP versions

▪ Emitter terminals placed symmetrically, pin 5 on NPN

and pin 1 on PNP models, allowing adjacent placement on

PCB to minimize trace length and output skew when used

in pairs

▪ Approved by major manufacturers

Darlington Transistors for Audio Amplifiers

Equivalent Circuits

Package: 5 pin TO-3P (MT-100)

Not to scale

Datasheet 28104.011

STD01N 3

STD01P

STD01N

12345

STD01P

12345

Emitter pins symmetrical

Darlington Transistors for Audio Amplifiers

STD01N and

STD01P

Sanken Electric Co., Ltd.

3-6-3 Kitano, Niiza-shi, Saitama-ken

352-8666, Japan

Phone:+81-48-472-1111

http://www.sanken-ele.co.jp

All performance characteristics given are typical values for circuit or

system baseline design only and are at the nominal operating voltage and

an ambient temperature of +25°C, unless oth er wise stated.

ABSOLUTE MAXIMUM RATINGS at TA = 25°C

Characteristic Symbol Rating Unit

Collector-Base Voltage1VCBO 150 V

Collector-Emitter Voltage1VCEO 150 V

Emitter-Base Voltage1VEBO 5V

Collector Current1IC10 A

Base Current1IB1A

Collector Power Dissipation2PC100 W

Diode Forward Current IF10 mA

Junction Temperature TJ150 °C

Storage Temperature Tstg –55 to150 °C

1For PNP type (STD01P), voltage and current values are negative.

2TC = 25°C.

SELECTION GUIDE

Part Number Type hFE Rating Packing

STD01N* NPN Range O: 5000 to 12000

Bulk, 100 pieces

Range Y: 8000 to 20000

STD01P* PNP Range O: 5000 to 12000

Range Y: 8000 to 20000

*Specify hFE range when ordering. If no hFE range is specified, order will be fulfilled with either or both range O and range Y,

depending upon availability.

ELECTRICAL CHARACTERISTICS at TA = 25°C

Characteristic Symbol Test Conditions Min. Typ. Max. Unit

Collector-Cutoff Current1ICBO VCB = 150 V – – 100 μA

Emitter Cutoff Current1IEBO VEB = 5 V – – 100 μA

Collector-Emitter Voltage1VCEO IC = 30 mA 150 – – V

DC Current Transfer Ratio2,3 hFE VCE = 4 V, IC = 6 A 5000 – 20000 –

Collector-Emitter Saturation Voltage1VCE(sat) IC = 6 A, IB = 6 mA – – –2.0 V

Base-Emitter Saturation Voltage1VBE(sat) IC = 6 A, IB = 6 mA – – –2.5 V

Base-Emitter Voltage VBE

STD01N VCE = 20 V, IC = 40 mA – 1220 – mV

STD01P VCE = –20 V, IC = –40 mA – 1230 – mV

Diode Forward Voltage VF

STD01N IF = 2.5 mA – 705 – mV

STD01P IF = 2.5 mA – 1580 – mV

1For PNP type (STD01P), voltage and current values are negative.

2hFE rating: 5000 to 12000(O brand on package), 8000 to 20000 (Y).

3When the transistor is used in pairs, the following conditions must be satisﬁ ed: Total VF ≤ Total VBE of the transistors (the above measurement

conditions shall be applied), and ∆V = 0 to 500 mV.

Darlington Transistors for Audio Amplifiers

STD01N and

STD01P

Sanken Electric Co., Ltd.

3-6-3 Kitano, Niiza-shi, Saitama-ken

352-8666, Japan

Phone:+81-48-472-1111

http://www.sanken-ele.co.jp

02 4 6

(V)

(A)

0.0001 0.001 0.01 0.1 1

CE(sat)

(V)

6 A

8 A

=4 A

0 0.5 1.0 1.5 2.0 2.5

0.1 1 10 100

0 0.5 1.0 1.5 2.0

1 10 100 1000

0.01

0.10

1.00

10.00

110100

1000

vs. T

100

0 25 50 75 100 125 150

(°C)

(W)

Without Heatsink

With InfiniteHeatsink

3.5

vs. V

CE(sat)

vs. I

vs. V

θJA

vs. t

vs. V

For Diode

Safe Operating

Area

θJA

(°C/W)

10 mA

2.0mA

1.5 mA

1.0 mA

0.8 mA

0.5 mA

0.3 mA

125°C

25°C

–30°C

125°C

10 ms

100 ms

25°C

–30°C

= 0.2 mA

(A)

= 4 V Continuous V

= 4 V Continuous

Single pulse

No heatsink

Natural cooling

=25°

(V)

(mA)

VF(V)

t(ms)

(A)

IC(A)

hFE

102

103

104

105

106

0.01

0.1

1.0

10.0

100.0

(V)

IC(A)

STD01N Performance Characteristics at TA = 25°C

Darlington Transistors for Audio Amplifiers

STD01N and

STD01P

Sanken Electric Co., Ltd.

3-6-3 Kitano, Niiza-shi, Saitama-ken

352-8666, Japan

Phone:+81-48-472-1111

http://www.sanken-ele.co.jp

02 4 6

–V

(V)

–I

(A)

0.0001 0.001 0.01 0.1 1

–V

CE(sat)

(V)

6 A

8 A

–I

=4 A

0 0.5 1.0 1.5 2.0 2.5

0.1 1 10 100

0 0.5 1.0 1.5 2.52.0

1 10 100 1000

0.01

0.10

1.00

10.00

110100

1000

vs. T

100

0 25 50 75 100 125 150

(°C)

(W)

Without Heatsink

With Infinite Heatsink

3.5

vs. V

CE(sat)

vs. I

vs. V

θJA

vs. t

vs. V

For Diode

Safe Operating

Area

θJA

(°C/W)

10 mA

2.0mA

1.5 mA

1.0 mA

0.8 mA

0.5 mA

0.3 mA

125°C

25°C

–30°C

125°C

10 ms

100 ms

25°C

–30°C

–I

= 0.2 mA

–I

(A)

–V

= 4 V Continuous –V

= 4 V Continuous

Single pulse

No heatsink

Natural cooling

=25°

–V

(V)

(mA)

VF(V)

t(ms)

–I

(A)

–IC(A)

hFE

102

103

104

105

106

0.01

0.1

1.0

10.0

100.0

–V

(V)

IC(A)

STD01P Performance Characteristics at TA = 25°C

Darlington Transistors for Audio Amplifiers

STD01N and

STD01P

Sanken Electric Co., Ltd.

3-6-3 Kitano, Niiza-shi, Saitama-ken

352-8666, Japan

Phone:+81-48-472-1111

http://www.sanken-ele.co.jp

STD01N

Terminal

Configuration

STD01P

Terminal

Configuration

15.6 ±0.3

15.8 ±0.2

4.8 ±0.2

1.7 ±0.1

Terminal dimensions at case surface

Terminal dimension

at case surface

Terminal dimension at lead tips

1.74+0.2

–0.1 1.34+0.2

–0.1

1.05+0.2

–0.1

0.65+0.2

–0.1

20.5+1

–0.5

2+0.2

–0.1

3.2 +0.1

–0.2

19.9 ±0.3

14.9 ±0.2 2 ±0.2

3 MAX

(35.4)

Gate Burr

Branding

XXXXXXXX

Gate burr: 0.3 mm (max.), mold flash may appear at opposite side

Terminal core material: Cu

Terminal treatment: Ni plating and solder dip

Heat sink material: Cu

Heat sink treatment: Ni plating

Leadform: 2804

Weight (approximate): 6.0 g

Dimensions in millimeters

Branding codes (exact appearance at manufacturer discretion):

1st line, type: STD01X

Where: X is the transistor type (N or P)

2nd line, lot: YMDD H

Where: Y is the last digit of the year of manufacture

M is the month (1 to 9, O, N, D)

DD is the 2-digit date

H is the hFE rating (O or Y; for values see

footnote, Electrical Characteristics table)

12345

4×P2.54 ±0.6 = 10.16 ±0.8

4×P2.54 ±0.1 = (10.16)

12345

PACKAGE OUTLINE DRAWING, TO-3P

Leadframe plating Pb-free. Device composition

includes high-temperature solder (Pb >85%),

which is exempted from the RoHS directive.

Darlington Transistors for Audio Amplifiers

STD01N and

STD01P

Sanken Electric Co., Ltd.

3-6-3 Kitano, Niiza-shi, Saitama-ken

352-8666, Japan

Phone:+81-48-472-1111

http://www.sanken-ele.co.jp

WARNING — These devices are designed to be operated at lethal voltages and energy levels. Circuit designs

that embody these components must conform with applicable safety requirements. Pre cau tions must be

taken to prevent accidental contact with power-line potentials. Do not connect ground ed test equipment.

The use of an isolation transformer is recommended during circuit development and breadboarding.

Because reliability can be affected adversely by improper storage environments and handling methods, please

observe the following cautions.

Cautions for Storage

• Ensure that storage conditions comply with the standard temperature (5°C to 35°C) and the standard relative

humidity (around 40 to 75%); avoid storage locations that experience extreme changes in temperature or

humidity.

• Avoid locations where dust or harmful gases are present and avoid direct sunlight.

• Reinspect for rust in leads and solderability of products that have been stored for a long time.

Cautions for Testing and Handling

When tests are carried out during inspection testing and other standard test periods, protect the products from

power surges from the testing device, shorts between adjacent products, and shorts to the heatsink.

Remarks About Using Silicone Grease with a Heatsink

• When silicone grease is used in mounting this product on a heatsink, it shall be applied evenly and thinly. If more

silicone grease than required is applied, it may produce stress.

• Volatile-type silicone greases may produce cracks after long periods of time, resulting in reduced heat radiation

effect. Silicone grease with low consistency (hard grease) may cause cracks in the mold resin when screwing the

product to a heatsink.

• Our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the

product life, are indicated below:

Type Suppliers

G746 Shin-Etsu Chemical Co., Ltd.

YG6260 Toshiba Silicone Co., Ltd.

SC102 Dow Corning Toray Silicone Co., Ltd.

Heatsink Mounting Method

• Torque When Tightening Mounting Screws. Thermal resistance increases when tightening torque is low, and radiation

effects are decreased. When the torque is too high, the screw can strip, the heatsink can be deformed, and distortion

can arise in the product frame. To avoid these problems, observe the recommended tightening torques for this product

package type, TO-3P (MT-100): 0.686 to 0.882 N•m (7 to 9 kgf•cm).

• Diameter of Heatsink Hole: < 4 mm. The deﬂ ection of the press mold when making the hole may cause the case material

to crack at the joint with the heatsink. Please pay special attention for this effect.

Soldering

• When soldering the products, please be sure to minimize the working time, within the following limits:

260±5°C 10 s

350±5°C 3 s

• Soldering iron should be at a distance of at least 1.5 mm from the body of the products

Electrostatic Discharge

• When handling the products, operator must be grounded. Grounded wrist straps worn should have at least 1 MΩ

of resistance to ground to prevent shock hazard.

• Workbenches where the products are handled should be grounded and be provided with conductive table and

floor mats.

• When using measuring equipment such as a curve tracer, the equipment should be grounded.

• When soldering the products, the head of soldering irons or the solder bath must be grounded in other to prevent

leak voltages generated by them from being applied to the products.

• The products should always be stored and transported in our shipping containers or conductive containers, or be

wrapped in aluminum foil.

Darlington Transistors for Audio Amplifiers

STD01N and

STD01P

Sanken Electric Co., Ltd.

3-6-3 Kitano, Niiza-shi, Saitama-ken

352-8666, Japan

Phone:+81-48-472-1111

http://www.sanken-ele.co.jp

The products described herein are manufactured in Ja pan by Sanken Electric Co., Ltd.

Sanken reserves the right to make, from time to time, such de par tures from the detail spec i fi ca tions as may be re quired to per mit im prove ments in

the per for mance, reliability, or manufacturability of its prod ucts. Therefore, the user is cau tioned to verify that the in for ma tion in this publication is

current before placing any order.

When using the products described herein, the ap pli ca bil i ty and suit abil i ty of such products for the intended purpose shall be reviewed at the users

responsibility.

Although Sanken undertakes to enhance the quality and reliability of its prod ucts, the occurrence of failure and defect of semi con duc tor products

at a certain rate is in ev i ta ble.

Users of Sanken products are requested to take, at their own risk, preventative measures including safety design of the equipment or systems

against any possible injury, death, fires or damages to society due to device failure or malfunction.

Sanken products listed in this publication are designed and intended for use as components in general-purpose electronic equip ment or apparatus

(home ap pli anc es, office equipment, tele com mu ni ca tion equipment, measuring equipment, etc.). Their use in any application requiring radiation

hardness assurance (e.g., aero space equipment) is not supported.

When considering the use of Sanken products in ap pli ca tions where higher reliability is re quired (transportation equipment and its control systems

or equip ment, fire- or burglar-alarm systems, various safety devices, etc.), contact a company sales representative to discuss and obtain written

confirmation of your spec i fi ca tions.

The use of Sanken products without the written consent of Sanken in applications where ex treme ly high reliability is required (aerospace equip-

ment, nuclear power-control stations, life-support systems, etc.) is strictly prohibited.

The information in clud ed herein is believed to be accurate and reliable. Ap pli ca tion and operation examples described in this pub li ca tion are

given for reference only and Sanken assumes no re spon si bil i ty for any in fringe ment of in dus tri al property rights, intellectual property rights, or any

other rights of Sanken or any third party that may result from its use.

Darlington Transistors for Audio Amplifiers

STD01N and STD01P August, 2007

Sanken Electric Co., Ltd.

T02-012EA-070820

Asia Pacific

China

Sanken Electric Hong Kong Co., Ltd.

Suite 1026 Ocean Centre, Canton Road, Tsimshatsui, Kowloon, Hong Kong

Te l: 852-2735-5262

Fax: 852-2735-5494

Sanken Elect ric (Shanghai) Co., Ltd.

Room3202, Maxdo Centre, Xingyi Road 8, Changning district, Shanghai, China

Tel: 86-21-5208-1177

Fax: 86-21-5208-1757

India

Saket Devices Pvt. Ltd.

Office No.13, First Floor, Bandal - Dhankude Plaza, Near PMT Depot, Paud Road, Kot hrud, Pune - 411 038, India

Tel: 91-20-5621-2340

91-20-2528-5449

Fax: 91-20-2528-5459

Japan

Sanken Electric Co., Ltd. Overseas Sales Headquaters

Metropolitan Plaza Bldg. 1-11-1 Nishi-Ikebukuro, Toshima-ku, Tokyo 171-0021, Japan

Te l: 81-3-3986-6164

Fax: 81-3-39 8 6- 8 637

Korea

Sanken Electric Korea Co., Ltd.

Mirae Asset Life Bldg. 6F, 168 Kongduk-dong, Mapo-ku, Seoul, 121-705, Korea

Te l: 82-2-714-3700

Fax: 82-2-32 7 2- 2 145

Singapore

Sanken Electric Singapore Pte. Ltd.

150 Beach Road, #14-03 The Gateway West, Singapore 1897 20

Te l: 65-6291-4755

Fax: 65-6297-1744

Taiwan

Taiwan Sanken Electric Co., Ltd.

Room 1801, 18th Floor, 88 Jung Shiau East Road , Sec. 2, Taipei 100, Taiwan R.O.C.

Tel: 886-2-2356-8161

Fax: 886-2-2356-8261

Darlington Transistors for Audio Amplifiers

STD01N and STD01P August, 2007

Sanken Electric Co., Ltd.

T02-012EA-070820

Europe

United Kingdom

Sanken Power Systems (UK) Limited

Pencoed Technology Par k Pencoed, Bridgend CF35 5HY. UK

Te l: 44-1656-869-100

Fax: 44-1656-869-162

North America

United States

Allegro MicroSystems, Inc.

115 Northeast Cutoff, Worcester, Massachusetts 01606, U.S.A.

Tel: 1-508-853-5000

Fax: 1-508-8 5 3- 3 353

Allegro MicroSystems, Inc. (Southern California)

14 Hughes Street, Suite B105, Irvine, CA 92618

Tel: 1-949-460-2003

Fax: 1-949-4 6 0- 7 837