SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 D Operation From -40C to 125C D - 0.5% . . . B Grade - 1% . . . A Grade - 2% . . . Standard Grade Typical Temperature Drift (TL431B) - 6 mV (C Temp) - 14 mV (I Temp, Q Temp) TL431, TL431A, TL431B . . . D (SOIC) PACKAGE (TOP VIEW) CATHODE ANODE ANODE NC 1 8 2 7 3 6 4 5 REF ANODE ANODE NC D D D D Low Output Noise 0.2- Typical Output Impedance Sink-Current Capability . . . 1 mA to 100 mA Adjustable Output Voltage . . . Vref to 36 V TL431, TL431A, TL431B . . . P (PDIP), PS (SOP), OR PW (TSSOP) PACKAGE (TOP VIEW) CATHODE NC NC NC 1 8 2 7 3 6 4 5 REF NC ANODE NC NC - No internal connection NC - No internal connection TL431, TL431A, TL431B . . . PK (SOT-89) PACKAGE (TOP VIEW) TL431, TL431A, TL431B . . . LP (TO-92/TO-226) PACKAGE (TOP VIEW) CATHODE CATHODE ANODE ANODE REF REF TL431, TL431A, TL431B . . . DBV (SOT23-5) PACKAGE (TOP VIEW) NC 1 NU 2 CATHODE 3 5 ANODE 4 REF TL431, TL431A, TL431B . . . DBZ (SOT23-3) PACKAGE (TOP VIEW) 1 3 REF 1 ANODE 2 NC 3 5 REF 4 CATHODE TL432, TL432A, TL432B . . . DBZ (SOT23-3) PACKAGE (TOP VIEW) REF 1 CATHODE 2 ANODE 3 2 TL431 . . . KTP (PowerFLEXE/TO-252) PACKAGE (TOP VIEW) ANODE NC NC - No internal connection NC - No internal connection NU - Make no external connection CATHODE TL432, TL432A, TL432B . . . DBV (SOT23-5) PACKAGE (TOP VIEW) CATHODE ANODE REF ANODE TL431A, TL431B . . . DCK (SC-70) PACKAGE (TOP VIEW) CATHODE NC REF 1 6 2 5 3 4 ANODE NC NC NC - No internal connection Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerFLEX is a trademark of Texas Instruments. Copyright 2004, Texas Instruments Incorporated !"# $"%&! '#( '"! ! $#!! $# )# # #* "# '' +,( '"! $!#- '# #!#&, !&"'# #- && $##( POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 description/ordering information The TL431 and TL432 are three-terminal adjustable shunt regulators, with specified thermal stability over applicable automotive, commercial, and military temperature ranges. The output voltage can be set to any value between Vref (approximately 2.5 V) and 36 V, with two external resistors (see Figure 17). These devices have a typical output impedance of 0.2 . Active output circuitry provides a very sharp turn-on characteristic, making these devices excellent replacements for Zener diodes in many applications, such as onboard regulation, adjustable power supplies, and switching power supplies. The TL432 has exactly the same functionality and electrical specifications as the TL431, but has different pinouts for the DBV and DBZ packages. Both the TL431 and TL432 devices are offered in three grades, with initial tolerances (at 25C) of 0.5%, 1%, and 2%, for the B, A, and standard grade, respectively. In addition, low output drift vs temperature ensures good stability over the entire temperature range. The TL43xxC devices are characterized for operation from 0C to 70C, the TL43xxI devices are characterized for operation from -40C to 85C, and the TL43xxQ devices are characterized for operation from -40C to 125C. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 description/ordering information (continued) Vref TOLERANCE (25C) = 2% TL431, TL432 ORDERING INFORMATION ORDERABLE PART NUMBER PACKAGE TA PDIP (P) SOIC (D) SOP (PS) SOT-23-5 (DBV) 0C to 70C SOT-23-3 (DBZ) SOT-89 (PK) TO-226/TO-92 (LP) TSSOP (PW) PDIP (P) SOIC (D) SOT-23-5 (DBV) -40C to 85C SOT-23-3 (DBZ) SOT-89 (PK) TO-226/TO-92 (LP) Tube of 50 TL431CP Tube of 75 TL431CD Reel of 2500 TL431CDR Reel of 2000 TL431CPSR Reel of 3000 TL431CDBVR Reel of 250 TL431CDBVT Reel of 3000 TL432CDBVR Reel of 250 TL432CDBVT Reel of 3000 TL431CDBZR Reel of 250 TL431CDBZT Reel of 3000 TL432CDBZR Reel of 250 TL432CDBZT Reel of 1000 TL431CPK Bulk of 1000 TL431CLP Ammo of 2000 TL431CLPM Reel of 2000 TL431CLPR Tube of 150 TL431CPW Reel of 2000 TL431CPWR Tube of 50 TL431IP Tube of 75 TL431ID Reel of 2500 TL431IDR Reel of 3000 TL431IDBVR Reel of 250 TL431IDBVT Reel of 3000 TL432IDBVR Reel of 250 TL432IDBVT Reel of 3000 TL431IDBZR Reel of 250 TL431IDBZT Reel of 3000 TL432IDBZR Reel of 250 TL432IDBZT Reel of 1000 TL431IPK Bulk of 1000 TL431ILP Reel of 2000 TL431ILPR TOP-SIDE MARKING TL431CP TL431C T431 T3C_ TAB_ TAC_ TAB_ 43 TL431C T431 TL431IP TL431I T3I_ T4A_ TAI_ T4A_ 3I TL431I Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. DBV/DBZ: The actual top-side marking has one additional character that designates the assembly/test site. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 3 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 description/ordering information (continued) Vref TOLERANCE (25C) = 2% TL431, TL432 ORDERING INFORMATION ORDERABLE PART NUMBER PACKAGE TA SOT-23-5 (DBV) -40C to 125C SOT-23-3 (DBZ) Reel of 3000 TL431QDBVR Reel of 250 TL431QDBVT Reel of 3000 TL432QDBVR Reel of 250 TL432QDBVT Reel of 3000 TL431QDBZR Reel of 250 TL431QDBZT Reel of 3000 TL432QDBZR Reel of 250 TL432QDBZT TOP-SIDE MARKING TBD TBD TBD TBD Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. DBV/DBZ: The actual top-side marking has one additional character that designates the assembly/test site. Vref TOLERANCE (25C) = 1% TL431A, TL432A ORDERING INFORMATION ORDERABLE PART NUMBER PACKAGE TA PDIP (P) SC-70 (DCK) SOIC (D) SOP (PS) SOT-23-5 (DBV) 0C to 70C SOT-23-3 (DBZ) SOT-89 (PK) TO-226/TO-92 (LP) TSSOP (PW) TOP-SIDE MARKING Tube of 50 TL431ACP Reel of 3000 TL431ACDCKR TL431ACP Reel of 250 TL431ACDCKT Tube of 75 TL431ACD Reel of 2500 TL431ACDR Reel of 2000 TL431ACPSR Reel of 3000 TL431ACDBVR Reel of 250 TL431ACDBVT Reel of 3000 TL432ACDBVR Reel of 250 TL432ACDBVT Reel of 3000 TL431ACDBZR Reel of 250 TL431ACDBZT Reel of 3000 TL432ACDBZR Reel of 250 TL432ACDBZT Reel of 1000 TL431ACPK 4A Bulk of 1000 TL431ACLP TL431AC Ammo of 2000 TL431ACLPM Reel of 2000 TL431ACLPR Tube of 150 TL431ACPW Reel of 2000 TL431ACPWR TBD 431AC T431A TAC_ TAB_ TAC_ TAB_ TL431AC T431A Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. DBV/DBZ/DCK: The actual top-side marking has one additional character that designates the assembly/test site. 4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 description/ordering information (continued) Vref TOLERANCE (25C) = 1% TL431A, TL432A ORDERING INFORMATION ORDERABLE PART NUMBER PACKAGE TA PDIP (P) SC-70 (DCK) SOIC (D) SOT-23-5 (DBV) -40C -40 C to 85 85C C SOT-23-3 (DBZ) SOT-89 (PK) TO-226/TO-92 (LP) SOT-23-5 (DBV) -40C to 125C SOT-23-3 (DBZ) Tube of 50 TL431AIP Reel of 3000 TL431AIDCKR Reel of 250 TL431AIDCKT Tube of 75 TL431AID Reel of 2500 TL431AIDR Reel of 3000 TL431AIDBVR Reel of 250 TL431AIDBVT Reel of 3000 TL432AIDBVR Reel of 250 TL432AIDBVT Reel of 3000 TL431AIDBZR Reel of 250 TL431AIDBZT Reel of 3000 TL432AIDBZR Reel of 250 TL432AIDBZT Reel of 1000 TL431AIPK Bulk of 1000 TL431AILP Ammo of 2000 TL431AILPM Reel of 2000 TL431AILPR Reel of 3000 TL431AQDBVR Reel of 250 TL431AQDBVR Reel of 3000 TL432AQDBVR Reel of 250 TL432AQDBVT Reel of 3000 TL431AQDBZR Reel of 250 TL431AQDBZT Reel of 3000 TL432AQDBZR Reel of 250 TL432AQDBZT TOP-SIDE MARKING TL431AIP TBD 431AI TAI_ T4A_ TAI_ T4A_ 4B TL431AI TBD TBD TBD TBD Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. DBV/DBZ/DCK: The actual top-side marking has one additional character that designates the assembly/test site. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 5 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 description/ordering information (continued) Vref TOLERANCE (25C) = 0.5% TL431B, TL432B ORDERING INFORMATION ORDERABLE PART NUMBER PACKAGE TA PDIP (P) SC-70 (DCK) SOIC (D) SOP (PS) SOT-23-5 (DBV) 0C to 70C SOT-23-3 (DBZ) SOT-89 (PK) TO-226/TO-92 (LP) TSSOP (PW) PDIP (P) SC-70 (DCK) SOIC (D) SOT-23-5 (DBV) -40C to 85C SOT-23-3 (DBZ) SOT-89 (PK) TO-226/TO-92 (LP) Tube of 50 TL431BCP Reel of 3000 TL431BCDCKR Reel of 250 TL431BCDCKT Tube of 75 TL431BCD Reel of 2500 TL431BCDR Reel of 2000 TL431BCPSR Reel of 3000 TL431BCDBVR Reel of 250 TL431BCDBVT Reel of 3000 TL432BCDBVR Reel of 250 TL432BCDBVT Reel of 3000 TL431BCDBZR Reel of 250 TL431BCDBZT Reel of 3000 TL432BCDBZR Reel of 250 TL432BCDBZT Reel of 1000 TL431BCPK Bulk of 1000 TL431BCLP Ammo of 2000 TL431BCLPM Reel of 2000 TL431BCLPR Tube of 150 TL431BCPW Reel of 2000 TL431BCPWR Tube of 50 TL431BIP Reel of 3000 TL431BIDCKR Reel of 250 TL431BIDCKT Tube of 75 TL431BID Reel of 2500 TL431BIDR Reel of 3000 TL431BIDBVR Reel of 250 TL431BIDBVT Reel of 3000 TL432BIDBVR Reel of 250 TL432BIDBVT Reel of 3000 TL431BIDBZR Reel of 250 TL431BIDBZT Reel of 3000 TL432BIDBZR Reel of 250 TL432IBDBZT Reel of 1000 TL431BIPK Bulk of 1000 TL431BILP Reel of 2000 TL431BILPR TOP-SIDE MARKING TL431BCP TBD T431B TL431B T3G_ TBC_ T3G_ TBC_ 4C TL431B T431B TL431BIP TBD Z431B T3F_ T4F_ T3F_ T4F_ 4I Z431B Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. DBV/DBZ/DCK: The actual top-side marking has one additional character that designates the assembly/test site. 6 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 description/ordering information (continued) Vref TOLERANCE (25C) = 0.5% TL431B, TL432B ORDERING INFORMATION (CONTINUED) ORDERABLE PART NUMBER PACKAGE TA SOIC (D) SOT-23-5 (DBV) -40C to 125C SOT-23-3 (DBZ) SOT-89 (PK) TO-226/TO-92 (LP) Tube of 75 TL431BQD Reel of 2500 TL431BQDR Reel of 3000 TL431BQDBVR Reel of 250 TL431BQDBVT Reel of 3000 TL432BQDBVR Reel of 250 TL432BQDBVT Reel of 3000 TL431BQDBZR Reel of 250 TL431BQDBZT Reel of 3000 TL432BQDBZR Reel of 250 TL432BQDBZT Reel of 1000 TL431BQPK Bulk of 1000 TL431BQLP Ammo of 2000 TL431BQLPM Reel of 2000 TL431BQLPR TOP-SIDE MARKING T431BQ T3H_ T4H_ T3H_ T4H_ 3H T431BQ Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. DBV/DBZ: The actual top-side marking has one additional character that designates the assembly/test site. symbol REF ANODE CATHODE functional block diagram CATHODE + REF _ Vref ANODE POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 7 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 equivalent schematic CATHODE 800 800 20 pF REF 150 3.28 k 2.4 k 4 k 10 k 20 pF 7.2 k 1 k 800 ANODE All component values are nominal. absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Cathode voltage, VKA (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 V Continuous cathode current range, IKA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -100 mA to 150 mA Reference input current range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50 A to 10 mA Operating virtual junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: Voltage values are with respect to the ANODE terminal, unless otherwise noted. package thermal data (see Note 2) PDIP (P) High K, JESD 51-7 JC 57C/W JA 85C/W SOIC (D) High K, JESD 51-7 39C/W 97C/W SOP (PS) High K, JESD 51-7 46C/W 95C/W SOT-89 (PK) High K, JESD 51-7 9C/W 52C/W SOT-23-5 (DBV) High K, JESD 51-7 131C/W 206C/W SOT-23-3 (DBZ) High K, JESD 51-7 TBD TBD TO-92 (LP) High K, JESD 51-7 55C/W 140C/W TSSOP (PW) High K, JESD 51-7 65C/W 149C/W PACKAGE BOARD NOTE 2: Maximum power dissipation is a function of TJ(max), JA, and TA. The maximum allowable power dissipation at any allowable ambient temperature is PD = (TJ(max) - TA)/JA. Operating at the absolute maximum TJ of 150C can affect reliability. 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 recommended operating conditions VKA IKA Cathode voltage Cathode current TL43xxC TA Operating free-air temperature range POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MIN MAX Vref 1 36 V 100 mA 0 70 TL43xxI -40 85 TL43xxQ -40 125 UNIT C C 9 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 electrical characteristics over recommended operating conditions, TA = 25C (unless otherwise noted) TL431C, TL432C TEST CIRCUIT PARAMETER TEST CONDITIONS IKA = 10 mA SOT23-3 and TL432 devices UNIT MIN TYP MAX 2440 2495 2550 6 16 4 25 -1.4 -2.7 -1 -2 mV V Vref Reference voltage 2 VKA = Vref, VI(dev) Deviation of reference voltage over full temperature range (see Figure 1) 2 VKA = Vref, IKA = 10 mA, TA = 0C to 70C DV ref DV KA Ratio of change in reference voltage to the change in cathode voltage 3 IKA = 10 mA Iref Reference current 3 IKA = 10 mA, R1 = 10 k, R2 = 2 4 A II(dev) Deviation of reference current over full temperature range (see Figure 1) 3 IKA = 10 mA, R1 = 10 k, R2 = , TA = 0C to 70C 0.4 1.2 A Imin Minimum cathode current for regulation 2 VKA = Vref 0.4 1 mA Ioff Off-state cathode current 4 0.1 1 A |zKA| Dynamic impedance (see Figure 1) 1 VKA = 36 V, Vref = 0 IKA = 1 mA to 100 mA, VKA = Vref, f 1 kHz 0.2 0.5 All other devices VKA = 10 V - Vref VKA = 36 V - 10 V mV mV The deviation parameters Vref(dev) and Iref(dev) are defined as the differences between the maximum and minimum values obtained over the recommended temperature range. The average full-range temperature coefficient of the reference voltage, Vref, is defined as: a ppm + V ref V( I dev) V at 25C ref Maximum Vref 10 6 VI(dev) Minimum Vref DT A C TA where: TA is the recommended operating free-air temperature range of the device. a Vref can be positive or negative, depending on whether minimum Vref or maximum Vref, respectively, occurs at the lower temperature. Example: maximum Vref = 2496 mV at 30C, minimum Vref = 2492 mV at 0C, Vref = 2495 mV at 25C, TA = 70C for TL431C a + V ref 4 mV 2495 mV 10 6 70C [ 23 ppm C Because minimum Vref occurs at the lower temperature, the coefficient is positive. Calculating Dynamic Impedance The dynamic impedance is defined as: |z KA| + DV KA DI KA When the device is operating with two external resistors (see Figure 3), the total dynamic impedance of the circuit is given by: |z| + DV [ |z KA| 1 ) R1 DI R2 Figure 1. Calculating Deviation Parameters and Dynamic Impedance 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 electrical characteristics over recommended operating conditions, TA = 25C (unless otherwise noted) PARAMETER Vref Reference voltage TL431I, TL432I TEST CIRCUIT TEST CONDITIONS IKA = 10 mA SOT23-3 and TL432 devices UNIT MIN TYP MAX 2440 2495 2550 14 34 5 50 -1.4 -2.7 -1 -2 mV V 2 VKA = Vref, Deviation of reference voltage VI(dev) over full temperature range (see Figure 1) 2 VKA = Vref, IKA = 10 mA, TA = -40C to 85C All other devices DV ref DV KA Ratio of change in reference voltage to the change in cathode voltage 3 IKA = 10 mA Iref Reference current 3 IKA = 10 mA, R1 = 10 k, R2 = 2 4 A II(dev) Deviation of reference current over full temperature range (see Figure 1) 3 IKA = 10 mA, R1 = 10 k, R2 = , TA = -40C to 85C 0.8 2.5 A Imin Minimum cathode current for regulation 2 VKA = Vref 0.4 1 mA Ioff Off-state cathode current 4 0.1 1 A |zKA| Dynamic impedance (see Figure 1) 2 VKA = 36 V, Vref = 0 IKA = 1 mA to 100 mA, VKA = Vref, f 1 kHz 0.2 0.5 VKA = 10 V - Vref VKA = 36 V - 10 V mV mV electrical characteristics over recommended operating conditions, TA = 25C (unless otherwise noted) PARAMETER TL431Q, TL432Q TEST CIRCUIT TEST CONDITIONS TYP MAX 2440 2495 2550 mV 14 34 mV -1.4 -2.7 -1 -2 mV V Vref Reference voltage 2 VKA = Vref, VI(dev) Deviation of reference voltage over full temperature range (see Figure 1) 2 VKA = Vref, IKA = 10 mA, TA = -40C to 125C DV ref DV KA Ratio of change in reference voltage to the change in cathode voltage 3 IKA = 10 mA Iref Reference current 3 IKA = 10 mA, R1 = 10 k, R2 = 2 4 A II(dev) Deviation of reference current over full temperature range (see Figure 1) 3 IKA = 10 mA, R1 = 10 k, R2 = , TA = -40C to 125C 0.8 2.5 A Imin Minimum cathode current for regulation 2 VKA = Vref 0.4 1 mA Ioff Off-state cathode current 4 0.1 1 A |zKA| Dynamic impedance (see Figure 1) 2 VKA = 36 V, Vref = 0 IKA = 1 mA to 100 mA, VKA = Vref, f 1 kHz 0.2 0.5 POST OFFICE BOX 655303 IKA = 10 mA UNIT MIN VKA = 10 V - Vref VKA = 36 V - 10 V * DALLAS, TEXAS 75265 11 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 electrical characteristics over recommended operating conditions, TA = 25C (unless otherwise noted) TL431AC, TL432AC TEST CIRCUIT PARAMETER TEST CONDITIONS IKA = 10 mA SOT23-3, SC-70, and TL432 devices UNIT MIN TYP MAX 2470 2495 2520 6 16 4 25 -1.4 -2.7 -1 -2 mV V Vref Reference voltage 2 VKA = Vref, VI(dev) Deviation of reference voltage over full temperature range (see Figure 1) 2 VKA = Vref, IKA = 10 mA, TA = 0C to 70C DV ref DV KA Ratio of change in reference voltage to the change in cathode voltage 3 IKA = 10 mA Iref Reference current 3 IKA = 10 mA, R1 = 10 k, R2 = 2 4 A II(dev) Deviation of reference current over full temperature range (see Figure 1) 3 IKA = 10 mA, R1 = 10 k, R2 = , TA = 0C to 70C 0.8 1.2 A Imin Minimum cathode current for regulation 2 VKA = Vref 0.4 0.6 mA Ioff Off-state cathode current 4 0.1 0.5 A |zKA| Dynamic impedance (see Figure 1) 1 VKA = 36 V, Vref = 0 IKA = 1 mA to 100 mA, VKA = Vref, f 1 kHz 0.2 0.5 All other devices VKA = 10 V - Vref VKA = 36 V - 10 V mV mV electrical characteristics over recommended operating conditions, TA = 25C (unless otherwise noted) TL431AI, TL432AI TEST CIRCUIT PARAMETER TEST CONDITIONS TYP MAX 2470 2495 2520 14 34 5 50 -1.4 -2.7 -1 -2 mV V Vref Reference voltage 2 VKA = Vref, VI(dev) Deviation of reference voltage over full temperature range (see Figure 1) 2 VKA = Vref, IKA = 10 mA, TA = -40C to 85C All other packages DV ref DV KA Ratio of change in reference voltage to the change in cathode voltage 3 IKA = 10 mA Iref Reference current 3 IKA = 10 mA, R1 = 10 k, R2 = 2 4 A II(dev) Deviation of reference current over full temperature range (see Figure 1) 3 IKA = 10 mA, R1 = 10 k, R2 = , TA = -40C to 85C 0.8 2.5 A Imin Minimum cathode current for regulation 2 VKA = Vref 0.4 0.7 mA Ioff Off-state cathode current 4 0.1 0.5 A |zKA| Dynamic impedance (see Figure 1) 2 VKA = 36 V, Vref = 0 IKA = 1 mA to 100 mA, VKA = Vref, f 1 kHz 0.2 0.5 12 POST OFFICE BOX 655303 IKA = 10 mA SOT23-3, SC-70, and TL432 devices UNIT MIN VKA = 10 V - Vref VKA = 36 V - 10 V * DALLAS, TEXAS 75265 mV mV SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 electrical characteristics over recommended operating conditions, TA = 25C (unless otherwise noted) PARAMETER TL431AQ, TL432AQ TEST CIRCUIT TEST CONDITIONS IKA = 10 mA UNIT MIN TYP MAX 2470 2495 2520 mV 14 34 mV -1.4 -2.7 -1 -2 mV V Vref Reference voltage 2 VKA = Vref, VI(dev) Deviation of reference voltage over full temperature range (see Figure 1) 2 VKA = Vref, IKA = 10 mA, TA = -40C to 125C DV ref DV KA Ratio of change in reference voltage to the change in cathode voltage 3 IKA = 10 mA Iref Reference current 3 IKA = 10 mA, R1 = 10 k, R2 = 2 4 A II(dev) Deviation of reference current over full temperature range (see Figure 1) 3 IKA = 10 mA, R1 = 10 k, R2 = , TA = -40C to 125C 0.8 2.5 A Imin Minimum cathode current for regulation 2 VKA = Vref 0.4 0.7 mA Ioff Off-state cathode current 4 0.1 0.5 A |zKA| Dynamic impedance (see Figure 1) 2 VKA = 36 V, Vref = 0 IKA = 1 mA to 100 mA, VKA = Vref, f 1 kHz 0.2 0.5 VKA = 10 V - Vref VKA = 36 V - 10 V electrical characteristics over recommended operating conditions, TA = 25C (unless otherwise noted) PARAMETER TL431BC, TL432BC TEST CIRCUIT TEST CONDITIONS TYP MAX 2483 2495 2507 mV 6 16 mV -1.4 -2.7 -1 -2 mV V Vref Reference voltage 2 VKA = Vref, VI(dev) Deviation of reference voltage over full temperature range (see Figure 1) 2 VKA = Vref, IKA = 10 mA, TA = 0C to 70C DV ref DV KA Ratio of change in reference voltage to the change in cathode voltage 3 IKA = 10 mA Iref Reference current 3 IKA = 10 mA, R1 = 10 k, R2 = 2 4 A II(dev) Deviation of reference current over full temperature range (see Figure 1) 3 IKA = 10 mA, R1 = 10 k, R2 = , TA = 0C to 70C 0.8 1.2 A Imin Minimum cathode current for regulation 2 VKA = Vref 0.4 0.6 mA Ioff Off-state cathode current 4 0.1 0.5 A |zKA| Dynamic impedance (see Figure 1) 1 VKA = 36 V, Vref = 0 IKA = 1 mA to 100 mA, VKA = Vref, f 1 kHz 0.2 0.5 POST OFFICE BOX 655303 IKA = 10 mA UNIT MIN VKA = 10 V - Vref VKA = 36 V - 10 V * DALLAS, TEXAS 75265 13 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 electrical characteristics over recommended operating conditions, TA = 25C (unless otherwise noted) TL431BI, TL432BI TEST CIRCUIT PARAMETER TEST CONDITIONS IKA = 10 mA UNIT MIN TYP MAX 2483 2495 2507 mV 14 34 mV -1.4 -2.7 -1 -2 mV V Vref Reference voltage 2 VKA = Vref, VI(dev) Deviation of reference voltage over full temperature range (see Figure 1) 2 VKA = Vref, IKA = 10 mA, TA = -40C to 85C DV ref DV KA Ratio of change in reference voltage to the change in cathode voltage 3 IKA = 10 mA Iref Reference current 3 IKA = 10 mA, R1 = 10 k, R2 = 2 4 A II(dev) Deviation of reference current over full temperature range (see Figure 1) 3 IKA = 10 mA, R1 = 10 k, R2 = , TA = -40C to 85C 0.8 2.5 A Imin Minimum cathode current for regulation 2 VKA = Vref 0.4 0.7 mA Ioff Off-state cathode current 4 0.1 0.5 A |zKA| Dynamic impedance (see Figure 1) 2 VKA = 36 V, Vref = 0 IKA = 1 mA to 100 mA, VKA = Vref, f 1 kHz 0.2 0.5 VKA = 10 V - Vref VKA = 36 V - 10 V electrical characteristics over recommended operating conditions, TA = 25C (unless otherwise noted) TL431BQ, TL432BQ TEST CIRCUIT PARAMETER TEST CONDITIONS TYP MAX 2483 2495 2507 mV 14 34 mV -1.4 -2.7 -1 -2 mV V Vref Reference voltage 2 VKA = Vref, VI(dev) Deviation of reference voltage over full temperature range (see Figure 1) 2 VKA = Vref, IKA = 10 mA, TA = -40C to 125C DV ref DV KA Ratio of change in reference voltage to the change in cathode voltage 3 IKA = 10 mA Iref Reference current 3 IKA = 10 mA, R1 = 10 k, R2 = 2 4 A II(dev) Deviation of reference current over full temperature range (see Figure 1) 3 IKA = 10 mA, R1 = 10 k, R2 = , TA = -40C to 125C 0.8 2.5 A Imin Minimum cathode current for regulation 2 VKA = Vref 0.4 0.7 mA Ioff Off-state cathode current 4 0.1 0.5 A |zKA| Dynamic impedance (see Figure 1) 1 VKA = 36 V, Vref = 0 IKA = 1 mA to 100 mA, VKA = Vref, f 1 kHz 0.2 0.5 14 POST OFFICE BOX 655303 IKA = 10 mA UNIT MIN VKA = 10 V - Vref VKA = 36 V - 10 V * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 PARAMETER MEASUREMENT INFORMATION Input VKA IKA Vref Figure 2. Test Circuit for VKA = Vref VKA Input IKA R1 Iref R2 Vref V KA + V ref 1 ) R1 ) I ref R2 R1 Figure 3. Test Circuit for VKA > Vref Input VKA Ioff Figure 4. Test Circuit for Ioff POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 15 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 TYPICAL CHARACTERISTICS Table 1. Graphs FIGURE Reference voltage vs Free-air temperature 5 Reference current vs Free-air temperature 6 Cathode current vs Cathode voltage 7, 8 OFF-state cathode current vs Free-air temperature 9 Ratio of delta reference voltage to delta cathode voltage vs Free-air temperature 10 Equivalent input noise voltage vs Frequency 11 Equivalent input noise voltage over a 10-s period 12 Small-signal voltage amplification vs Frequency 13 Reference impedance vs Frequency 14 Pulse response 15 Stability boundary conditions 16 Table 2. Application Circuits FIGURE 16 Shunt regulator 17 Single-supply comparator with temperature-compensated threshold 18 Precision high-current series regulator 19 Output control of a three-terminal fixed regulator 20 High-current shunt regulator 21 Crowbar circuit 22 Precision 5-V 1.5-A regulator 23 Efficient 5-V precision regulator 24 PWM converter with reference 25 Voltage monitor 26 Delay timer 27 Precision current limiter 28 Precision constant-current sink 29 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 TYPICAL CHARACTERISTICS REFERENCE CURRENT vs FREE-AIR TEMPERATURE REFERENCE VOLTAGE vs FREE-AIR TEMPERATURE 2600 R1 = 10 k R2 = IKA = 10 mA Vref = 2550 mV 2560 I ref - Reference Current - A V ref - Reference Voltage - mV 2580 5 VKA = Vref IKA = 10 mA 2540 2520 Vref = 2495 mV 2500 2480 2460 Vref = 2440 mV 2440 4 3 2 1 2420 2400 -75 -50 -25 0 25 50 100 75 0 -75 125 -50 -25 Figure 5 50 75 100 125 Figure 6 CATHODE CURRENT vs CATHODE VOLTAGE CATHODE CURRENT vs CATHODE VOLTAGE 150 800 VKA = Vref TA = 25C VKA = Vref TA = 25C 100 600 I KA - Cathode Current - A I KA - Cathode Current - mA 25 TA - Free-Air Temperature - C TA - Free-Air Temperature - C Data is for devices having the indicated value of Vref at IKA = 10 mA, TA = 25C. 125 0 75 50 25 0 -25 -50 Imin 400 200 0 -75 -100 -2 -1 0 2 1 3 -200 -1 VKA - Cathode Voltage - V 0 1 2 3 VKA - Cathode Voltage - V Figure 7 Figure 8 Data at high and low temperatures is applicable only within the recommended operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 17 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 TYPICAL CHARACTERISTICS RATIO OF DELTA REFERENCE VOLTAGE TO DELTA CATHODE VOLTAGE vs FREE-AIR TEMPERATURE OFF-STATE CATHODE CURRENT vs FREE-AIR TEMPERATURE - 0.85 2.5 VKA = 3 V to 36 V - 0.95 2 V ref / V KA - mV/V I off - Off-State Cathode Current - A VKA = 36 V Vref = 0 1.5 1 0.5 0 -75 -1.05 -1.15 -1.25 -1.35 -50 -25 0 25 50 75 100 -1.45 -75 125 -50 TA - Free-Air Temperature - C -25 0 25 50 75 100 125 TA - Free-Air Temperature - C Figure 10 Figure 9 EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY Vn - Equivalent Input Noise Voltage - nV/ Hz 260 IO = 10 mA TA = 25C 240 220 200 180 160 140 120 100 10 100 1k 10 k 100 k f - Frequency - Hz Figure 11 Data at high and low temperatures is applicable only within the recommended operating free-air temperature ranges of the various devices. 18 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 TYPICAL CHARACTERISTICS EQUIVALENT INPUT NOISE VOLTAGE OVER A 10-S PERIOD V n - Equivalent Input Noise Voltage - V 6 5 4 3 2 1 0 -1 -2 -3 f = 0.1 to 10 Hz IKA = 10 mA TA = 25C -4 -5 -6 0 1 2 3 4 5 6 7 8 9 10 t - Time - s 19.1 V 1 k 500 F 910 2000 F VCC TL431 (DUT) 820 + VCC 1 F TLE2027 AV = 10 V/mV + - 16 160 k 16 k 16 k 1 F TLE2027 - 22 F To Oscilloscope 33 k AV = 2 V/V 0.1 F 33 k VEE VEE Figure 12. Test Circuit for Equivalent Input Noise Voltage POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 19 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 TYPICAL CHARACTERISTICS SMALL-SIGNAL VOLTAGE AMPLIFICATION vs FREQUENCY IKA = 10 mA TA = 25C A V - Small-Signal Voltage Amplification - dB 60 IKA = 10 mA TA = 25C 50 Output 15 k IKA 232 40 9 F + 30 - 8.25 k 20 GND TEST CIRCUIT FOR VOLTAGE AMPLIFICATION 10 0 1k 10 k 100 k 1M 10 M f - Frequency - Hz Figure 13 REFERENCE IMPEDANCE vs FREQUENCY |z KA| - Reference Impedance - 100 IKA = 10 mA TA = 25C 1 k 10 IKA 50 - + GND 1 TEST CIRCUIT FOR REFERENCE IMPEDANCE 0.1 1k 10 k 100 k 1M 10 M f - Frequency - Hz Figure 14 20 Output POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 PULSE RESPONSE 6 TA = 25C Input Input and Output Voltage - V 5 220 Output 4 Pulse Generator f = 100 kHz 3 Output GND 2 TEST CIRCUIT FOR PULSE RESPONSE 1 0 -1 50 0 1 2 3 4 5 6 7 t - Time - s Figure 15 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 21 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 TYPICAL CHARACTERISTICS STABILITY BOUNDARY CONDITIONS FOR ALL TL431 AND TL431A DEVICES (EXCEPT FOR SOT23-3, SC-70, AND Q-TEMP DEVICES) 100 90 I KA - Cathode Current - mA 80 A VKA = Vref B VKA = 5 V C VKA = 10 V D VKA = 15 Vf 150 IKA + TA = 25C VBATT CL - B 70 Stable 60 C Stable TEST CIRCUIT FOR CURVE A 50 A 40 IKA 150 R1 = 10 k 30 D 20 CL + 10 R2 0 0.001 VBATT - 0.01 0.1 10 1 CL - Load Capacitance - F TEST CIRCUIT FOR CURVES B, C, AND D STABILITY BOUNDARY CONDITIONS FOR ALL TL431B, TL432, SOT-23, SC-70, AND Q-TEMP DEVICES 100 90 I KA - Cathode Current - mA 80 150 A VKA = Vref B VKA = 5 V C VKA = 10 V D VKA = 15 Vf IKA + B 70 VBATT CL Stable - TA = 25C 60 C Stable 50 A TEST CIRCUIT FOR CURVE A 40 A 30 D IKA 20 150 R1 = 10 k B 10 0 0.001 CL + 0.01 0.1 1 10 R2 CL - Load Capacitance - F - The areas under the curves represent conditions that may cause the device to oscillate. For curves B, C, and D, R2 and V+ were adjusted to establish the initial VKA and IKA conditions with CL = 0. VBATT and CL then were adjusted to determine the ranges of stability. TEST CIRCUIT FOR CURVES B, C, AND D Figure 16 22 POST OFFICE BOX 655303 VBATT * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 APPLICATION INFORMATION R (see Note A) VI(BATT) VO R1 0.1% Vref TL431 V O + 1 ) R1 V ref R2 R2 0.1% RETURN NOTE A: R should provide cathode current 1 mA to the TL431 at minimum VI(BATT). Figure 17. Shunt Regulator VI(BATT) VO TL431 Von 2 V Voff VI(BATT) Input VIT 2.5 V GND Figure 18. Single-Supply Comparator With Temperature-Compensated Threshold VI(BATT) R (see Note A) 2N222 2N222 30 V 0.01 F 4.7 k TL431 O + 1 ) R1 V ref R2 VO R2 0.1% R1 0.1% NOTE A: R should provide cathode current 1 mA to the TL431 at minimum VI(BATT). Figure 19. Precision High-Current Series Regulator POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 23 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 APPLICATION INFORMATION VI(BATT) IN OUT uA7805 Common VO R1 TL431 V O + 1 ) R1 V ref R2 Minimum V O + V ref ) 5 V R2 Figure 20. Output Control of a Three-Terminal Fixed Regulator VI(BATT) VO R1 V O + 1 ) R1 V ref R2 TL431 R2 Figure 21. High-Current Shunt Regulator VI(BATT) VO R1 TL431 R2 C (see Note A) NOTE A: Refer to the stability boundary conditions in Figure 16 to determine allowable values for C. Figure 22. Crowbar Circuit 24 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 APPLICATION INFORMATION IN VI(BATT) LM317 8.2 k OUT Adjust VO 5 V, 1.5 A 243 0.1% TL431 243 0.1% Figure 23. Precision 5-V 1.5-A Regulator VO 5 V VI(BATT) Rb (see Note A) 27.4 k 0.1% TL431 27.4 k 0.1% NOTE A: Rb should provide cathode current 1 mA to the TL431. Figure 24. Efficient 5-V Precision Regulator 12 V VCC 6.8 k 5V 10 k 10 k 0.1% TL431 10 k 0.1% - + X Not Used TL598 Feedback Figure 25. PWM Converter With Reference POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 25 SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 APPLICATION INFORMATION R3 (see Note A) VI(BATT) R4 (see Note A) R1B R1A TL431 R2A Low Limit + 1 ) R1B V ref R2B High Limit + 1 ) R1A V ref R2A LED on When Low Limit < VI(BATT) < High Limit R2B NOTE A: R3 and R4 are selected to provide the desired LED intensity and cathode current 1 mA to the TL431 at the available VI(BATT). Figure 26. Voltage Monitor 650 12 V 2 k R TL431 Off Delay + R C In 12 V 12 V * V ref C On Figure 27. Delay Timer RCL 0.1% VI(BATT) IO I out + R1 TL431 R1 + Figure 28. Precision Current Limiter 26 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 V ref ) I KA R CL V I(BATT) I O h FE ) I KA SLVS543A - AUGUST 2004 - REVISED AUGUST 2004 APPLICATION INFORMATION VI(BATT) IO I TL431 O + V ref RS RS 0.1% Figure 29. Precision Constant-Current Sink POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 27 MECHANICAL DATA MCER001A - JANUARY 1995 - REVISED JANUARY 1997 JG (R-GDIP-T8) CERAMIC DUAL-IN-LINE 0.400 (10,16) 0.355 (9,00) 8 5 0.280 (7,11) 0.245 (6,22) 1 0.063 (1,60) 0.015 (0,38) 4 0.065 (1,65) 0.045 (1,14) 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0.023 (0,58) 0.015 (0,38) 0-15 0.100 (2,54) 0.014 (0,36) 0.008 (0,20) 4040107/C 08/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification. Falls within MIL STD 1835 GDIP1-T8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MLCC006B - OCTOBER 1996 FK (S-CQCC-N**) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS ** 12 19 11 20 10 A B MIN MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.739 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 25 5 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / D 10/96 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MPDI001A - JANUARY 1995 - REVISED JUNE 1999 P (R-PDIP-T8) PLASTIC DUAL-IN-LINE 0.400 (10,60) 0.355 (9,02) 8 5 0.260 (6,60) 0.240 (6,10) 1 4 0.070 (1,78) MAX 0.325 (8,26) 0.300 (7,62) 0.020 (0,51) MIN 0.015 (0,38) Gage Plane 0.200 (5,08) MAX Seating Plane 0.010 (0,25) NOM 0.125 (3,18) MIN 0.100 (2,54) 0.021 (0,53) 0.015 (0,38) 0.430 (10,92) MAX 0.010 (0,25) M 4040082/D 05/98 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 For the latest package information, go to http://www.ti.com/sc/docs/package/pkg_info.htm POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MPDS108 - AUGUST 2001 DBZ (R-PDSO-G3) PLASTIC SMALL-OUTLINE 3,04 2,80 2,05 1,78 0,60 0,45 1,03 0,89 1,40 1,20 2,64 2,10 0,51 0,37 1,12 0,89 0,100 0,013 0,55 REF 0,180 0,085 4203227/A 08/01 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Dimensions are inclusive of plating. Dimensions are exclusive of mold flash and metal burr. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MPSF001F - JANUARY 1996 - REVISED JANUARY 2002 KTP (R-PSFM-G2) PowerFLEX PLASTIC FLANGE-MOUNT PACKAGE 0.080 (2,03) 0.070 (1,78) 0.243 (6,17) 0.233 (5,91) 0.228 (5,79) 0.218 (5,54) 0.050 (1,27) 0.040 (1,02) 0.010 (0,25) NOM 0.130 (3,30) NOM 0.215 (5,46) NOM 0.247 (6,27) 0.237 (6,02) Thermal Tab (See Note C) 0.287 (7,29) 0.277 (7,03) 0.381 (9,68) 0.371 (9,42) 0.100 (2,54) 0.090 (2,29) 0.032 (0,81) MAX Seating Plane 0.090 (2,29) 0.180 (4,57) 0.004 (0,10) 0.005 (0,13) 0.001 (0,02) 0.031 (0,79) 0.025 (0,63) 0.010 (0,25) M 0.010 (0,25) NOM Gage Plane 0.047 (1,19) 0.037 (0,94) 0.010 (0,25) 2-6 4073388/M 01/02 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. The center lead is in electrical contact with the thermal tab. Dimensions do not include mold protrusions, not to exceed 0.006 (0,15). Falls within JEDEC TO-252 variation AC. PowerFLEX is a trademark of Texas Instruments. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 MECHANICAL DATA MSOT002A - OCTOBER 1994 - REVISED NOVEMBER 2001 LP (O-PBCY-W3) PLASTIC CYLINDRICAL PACKAGE 0.205 (5,21) 0.175 (4,44) 0.165 (4,19) 0.125 (3,17) DIA 0.210 (5,34) 0.170 (4,32) Seating Plane 0.157 (4,00) MAX 0.050 (1,27) C 0.500 (12,70) MIN 0.104 (2,65) FORMED LEAD OPTION 0.022 (0,56) 0.016 (0,41) 0.016 (0,41) 0.014 (0,35) STRAIGHT LEAD OPTION D 0.135 (3,43) MIN 0.105 (2,67) 0.095 (2,41) 0.055 (1,40) 0.045 (1,14) 1 2 3 0.105 (2,67) 0.080 (2,03) 0.105 (2,67) 0.080 (2,03) 4040001-2 /C 10/01 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Lead dimensions are not controlled within this area D. FAlls within JEDEC TO -226 Variation AA (TO-226 replaces TO-92) E. Shipping Method: Straight lead option available in bulk pack only. Formed lead option available in tape & reel or ammo pack. POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 MECHANICAL DATA MSOT002A - OCTOBER 1994 - REVISED NOVEMBER 2001 LP (O-PBCY-W3) PLASTIC CYLINDRICAL PACKAGE 0.539 (13,70) 0.460 (11,70) 1.260 (32,00) 0.905 (23,00) 0.650 (16,50) 0.610 (15,50) 0.020 (0,50) MIN 0.098 (2,50) 0.384 (9,75) 0.335 (8,50) 0.748 (19,00) 0.217 (5,50) 0.433 (11,00) 0.335 (8,50) 0.748 (19,00) 0.689 (17,50) 0.114 (2,90) 0.094 (2,40) 0.114 (2,90) 0.094 (2,40) 0.169 (4,30) 0.146 (3,70) DIA 0.266 (6,75) 0.234 (5,95) 0.512 (13,00) 0.488 (12,40) TAPE & REEL 4040001-3 /C 10/01 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Tape and Reel information for the Format Lead Option package. 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MECHANICAL DATA MTSS001C - JANUARY 1995 - REVISED FEBRUARY 1999 PW (R-PDSO-G**) PLASTIC SMALL-OUTLINE PACKAGE 14 PINS SHOWN 0,30 0,19 0,65 14 0,10 M 8 0,15 NOM 4,50 4,30 6,60 6,20 Gage Plane 0,25 1 7 0- 8 A 0,75 0,50 Seating Plane 0,15 0,05 1,20 MAX PINS ** 0,10 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064/F 01/97 NOTES: A. B. C. D. All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2004, Texas Instruments Incorporated