MC74LCX16373 Low-Voltage CMOS 16-Bit Transparent Latch With 5 V-Tolerant Inputs and Outputs (3-State, Non-Inverting) The MC74LCX16373 is a high performance, non-inverting 16-bit transparent latch operating from a 2.3 V to 3.6 V supply. The device is byte controlled. Each byte has separate Output Enable and Latch Enable inputs. These control pins can be tied together for full 16-bit operation. High impedance TTL compatible inputs significantly reduce current loading to input drivers while TTL compatible outputs offer improved switching noise performance. A VI specification of 5.5 V allows MC74LCX16373 inputs to be safely driven from 5.0 V devices. The MC74LCX16373 contains 16 D-type latches with 3-state 5.0 V-tolerant outputs. When the Latch Enable (LEn) inputs are HIGH, data on the Dn inputs enters the latches. In this condition, the latches are transparent, i.e., a latch output will change state each time its D input changes. When LE is LOW, the latches store the information that was present on the D inputs a setup time preceding the HIGH-to-LOW transition of LE. The 3-state outputs are controlled by the Output Enable (OEn) inputs. When OE is LOW, the outputs are enabled. When OE is HIGH, the standard outputs are in the high impedance state, but this does not interfere with new data entering into the latches. Features * * * * * * * * * * * * Designed for 2.3 to 3.6 V VCC Operation 5.4 ns Maximum tpd 5.0 V Tolerant - Interface Capability With 5.0 V TTL Logic Supports Live Insertion and Withdrawal IOFF Specification Guarantees High Impedance When VCC = 0 V LVTTL Compatible LVCMOS Compatible 24 mA Balanced Output Sink and Source Capability Near Zero Static Supply Current in All Three Logic States (20 mA) Substantially Reduces System Power Requirements Latchup Performance Exceeds 500 mA ESD Performance: Human Body Model >2000 V Machine Model >200 V These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant (c) Semiconductor Components Industries, LLC, 2012 July, 2012 - Rev. 10 1 http://onsemi.com 48 1 TSSOP-48 DT SUFFIX CASE 1201 MARKING DIAGRAM 48 LCX16373G AWLYYWW 1 A WL YY WW G = Assembly Location = Wafer Lot = Year = Work Week = Pb-Free Package ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 3 of this data sheet. Publication Order Number: MC74LCX16373/D MC74LCX16373 1 OE1 1 48 LE1 O0 2 47 D0 O1 3 46 D1 GND 4 44 D2 O3 6 43 D3 VCC 7 42 VCC O4 8 41 D4 O5 9 40 D5 48 O6 11 38 D6 O7 12 37 D7 O8 13 36 D8 O9 14 35 D9 GND 15 47 33 D10 O11 17 32 D11 VCC 18 31 VCC O12 19 30 D12 2 D1 D2 D5 29 D13 28 GND O14 22 27 D14 O15 23 26 D15 OE2 24 25 LE2 O5 Q D6 O7 Q D7 26 D15 D 22 O14 Q D 12 nLE 37 O13 Q 27 D14 D 20 nLE nLE O6 Q O12 D 11 nLE 38 29 D13 D 19 Q D 9 nLE 40 O11 Q 30 D12 D 17 nLE nLE O4 Q O10 Q D 8 nLE 41 32 D11 D D4 O13 20 O3 Q 16 nLE D 6 nLE D3 33 D10 D 43 GND 21 O2 Q O9 Q D 5 nLE 44 35 D9 D 14 nLE O1 Q O8 Q D 3 nLE 46 36 D8 D 13 nLE O0 Q D0 34 GND O10 16 25 LE2 nLE 39 GND GND 10 OE2 LE1 45 GND O2 5 24 OE1 23 nLE O15 Q D Figure 2. Logic Diagram Figure 1. Pinout: 48-Lead (Top View) Table 1. PIN NAMES Pins Function OEn Output Enable Inputs LEn Latch Enable Inputs D0-D15 Inputs O0-O15 Outputs Outputs Inputs TRUTH TABLE Inputs Outputs LE1 OE1 D0:7 O0:7 LE2 OE2 D8:15 O8:15 X H X Z X H X Z H L L L H L L L H L H H H L H H L L X O0 L L X O0 H = High Voltage Level L = Low Voltage Level Z = High Impedance State X = High or Low Voltage Level and Transitions Are Acceptable; for ICC reasons, DO NOT FLOAT Inputs http://onsemi.com 2 MC74LCX16373 ORDERING INFORMATION Package Shipping MC74LCX16373DTG TSSOP-48 (Pb-Free) 39 Units / Rail M74LCX16373DTR2G TSSOP-48 (Pb-Free) 2500 / Tape & Reel Device For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. MAXIMUM RATINGS Symbol VCC Parameter Value DC Supply Voltage VI DC Input Voltage VO DC Output Voltage Condition Units -0.5 to +7.0 V -0.5 VI +7.0 V -0.5 VO +7.0 Output in 3-State V -0.5 VO VCC + 0.5 Output in HIGH or LOW State. (Note 1) V IIK DC Input Diode Current -50 VI < GND mA IOK DC Output Diode Current -50 VO < GND mA +50 VO > VCC mA IO DC Output Source/Sink Current 50 mA ICC DC Supply Current Per Supply Pin 100 mA IGND DC Ground Current Per Ground Pin 100 mA TSTG Storage Temperature Range -65 to +150 C MSL Moisture Sensitivity Level 1 Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. IO absolute maximum rating must be observed. RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage Operating Data Retention Only Min Typ Max 2.0 1.5 2.5, 3.3 2.5, 3.3 3.6 3.6 VI Input Voltage 0 5.5 VO Output Voltage (HIGH or LOW State) (3-State) 0 0 VCC 5.5 IOH HIGH Level Output Current VCC = 3.0 V - 3.6 V VCC = 2.7 V - 3.0 V VCC = 2.3 V - 2.7 V -24 -12 -8 IOL LOW Level Output Current VCC = 3.0 V - 3.6 V VCC = 2.7 V - 3.0 V VCC = 2.3 V - 2.7 V +24 +12 +8 TA Operating Free-Air Temperature Dt/DV Input Transition Rise or Fall Rate, VIN from 0.8 V to 2.0 V, VCC = 3.0 V http://onsemi.com 3 Units V V V mA mA -55 +125 C 0 10 ns/V MC74LCX16373 DC ELECTRICAL CHARACTERISTICS TA = -55C to +125C Symbol VIH VIL VOH VOL Condition Min 2.3 V VCC 2.7 V 1.7 2.7 V VCC 3.6 V 2.0 Characteristic HIGH Level Input Voltage (Note 2) LOW Level Input Voltage (Note 2) HIGH Level Output Voltage LOW Level Output Voltage Max V 2.3 V VCC 2.7 V 0.7 2.7 V VCC 3.6 V 0.8 2.3 V VCC 3.6 V; IOL = 100 mA VCC - 0.2 VCC = 2.3 V; IOH = -8 mA 1.8 VCC = 2.7 V; IOH = -12 mA 2.2 VCC = 3.0 V; IOH = -18 mA 2.4 VCC = 3.0 V; IOH = -24 mA 2.2 Units V V 2.3 V VCC 3.6 V; IOL = 100 mA 0.2 V VCC = 2.3 V; IOL = 8 mA 0.6 VCC = 2.7 V; IOL = 12 mA 0.4 VCC = 3.0 V; IOL = 16 mA 0.4 VCC = 3.0 V; IOL = 24 mA 0.55 VCC = 3.6 V, VIN = VIH or VIL, VOUT = 0 to 3.6 V 5 mA IOZ 3-State Output Current IOFF Power Off Leakage Current VCC = 0, VIN = 3.6 V or VOUT = 3.6 V 10 mA IIN Input Leakage Current VCC = 0 to 3.6 V, VIN = 3.6 V or GND 5 mA ICC Quiescent Supply Current VCC = 3.6 V, VIN = 3.6 V or VOUT = 3.6 V 20 mA 2.3 VCC 3.6 V; VIH = VCC - 0.6 V 500 mA DICC Increase in ICC per Input 2. These values of VI are used to test DC electrical characteristics only. AC CHARACTERISTICS (tR = tF = 2.5 ns; CL = 50 pF; RL = 500 W) TA = -55C to +125C VCC = 3.3 V 0.3 V CL = 50 pF Symbol Parameter VCC = 2.7 V CL = 50 pF VCC = 2.5 V 0.2 V CL = 30 pF Waveform Min Max Min Max Min Max Units tPLH tPHL Propagation Delay Dn to On 1 1.5 1.5 5.4 5.4 1.5 1.5 5.9 5.9 1.5 1.5 6.5 6.5 ns tPLH tPHL Propagation Delay LE to On 3 1.5 1.5 5.5 5.5 1.5 1.5 6.4 6.4 1.5 1.5 6.6 6.6 ns tPZH tPZL Output Enable Time to High and Low Level 2 1.5 1.5 6.1 6.1 1.5 1.5 6.5 6.5 1.5 1.5 7.9 7.9 ns tPHZ tPLZ Output Disable Time From High and Low Level 2 1.5 1.5 6.0 6.0 1.5 1.5 6.3 6.3 1.5 1.5 7.2 7.2 ns ts Setup Time, HIGH or LOW Dn to LE 3 2.5 2.5 3.0 ns th Hold Time, HIGH or LOW Dn to LE 3 1.5 1.5 2.0 ns tw LE Pulse Width, HIGH 3 3.0 3.0 3.5 ns tOSHL tOSLH Output-to-Output Skew (Note 3) 1.0 1.0 ns 3. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH-to-LOW (tOSHL) or LOW-to-HIGH (tOSLH); parameter guaranteed by design. http://onsemi.com 4 MC74LCX16373 DYNAMIC SWITCHING CHARACTERISTICS TA = +25C Symbol Characteristic Min Condition Typ Max Units VOLP Dynamic LOW Peak Voltage (Note 4) VCC = 3.3 V, CL = 50 pF, VIH = 3.3 V, VIL = 0 V VCC = 2.5 V, CL = 30 pF, VIH = 2.5 V, VIL = 0 V 0.8 0.6 V VOLV Dynamic LOW Valley Voltage (Note 4) VCC = 3.3 V, CL = 50 pF, VIH = 3.3 V, VIL = 0 V VCC = 2.5 V, CL = 30 pF, VIH = 2.5 V, VIL = 0 V -0.8 -0.6 V 4. Number of outputs defined as "n". Measured with "n-1" outputs switching from HIGH-to-LOW or LOW-to-HIGH. The remaining output is measured in the LOW state. CAPACITIVE CHARACTERISTICS Symbol Condition Typical Units Input Capacitance VCC = 3.3 V, VI = 0 V or VCC 7 pF COUT Output Capacitance VCC = 3.3 V, VI = 0 V or VCC 8 pF CPD Power Dissipation Capacitance 10 MHz, VCC = 3.3 V, VI = 0 V or VCC 20 pF CIN Parameter VCC Vmi Vmi Dn tPHL tPLH 0V VOH Vmo On Vmo VOL WAVEFORM 1 - PROPAGATION DELAYS tR = tF = 2.5 ns, 10% to 90%; f = 1 MHz; tW = 500 ns VCC OEn VCC Dn Vmi Vmi tPZH tPHZ ts th VCC LEn Vmo tw Vmo 0V tPZL On VOH VHZ Vmo On 0V 0V tPLH, tPHL tPLZ VOH Vmo VLZ VOL WAVEFORM 2 - OUTPUT ENABLE AND DISABLE TIMES tR = tF = 2.5 ns, 10% to 90%; f = 1 MHz; tW = 500 ns On Vmo VOL WAVEFORM 3 - LE to On PROPAGATION DELAYS, LE MINIMUM PULSE WIDTH, Dn to LE SETUP AND HOLD TIMES tR = tF = 2.5 ns, 10% to 90%; f = 1 MHz; tW = 500 ns except when noted Figure 3. AC Waveforms Table 2. AC WAVEFORMS VCC Symbol 3.3 V 0.3 V 2.7 V 2.5 V 0.2 V Vmi 1.5 V 1.5 V VCC / 2 Vmo 1.5 V 1.5 V VCC / 2 VHZ VOL + 0.3 V VOL + 0.3 V VOL + 0.15 V VLZ VOH - 0.3 V VOH - 0.3 V VOH - 015 V http://onsemi.com 5 MC74LCX16373 VCC PULSE GENERATOR R1 DUT RT CL RL Figure 4. Test Circuit Table 3. TEST CIRCUIT Test Switch tPLH, tPHL Open tPZL, tPLZ 6 V at VCC = 3.3 0.3 V 6 V at VCC = 2.5 0.2 V Open Collector/Drain tPLH and tPHL 6V tPZH, tPHZ GND CL = CL = RL = RT = 50 pF at VCC = 3.3 0.3 V or equivalent (includes jig and probe capacitance) 30 pF at VCC = 2.5 0.2 V or equivalent (includes jig and probe capacitance) R1 = 500 W or equivalent ZOUT of pulse generator (typically 50 W) http://onsemi.com 6 6 V or VCC x 2 OPEN GND MC74LCX16373 PACKAGE DIMENSIONS 48X TSSOP-48 DT SUFFIX CASE 1201-01 ISSUE B K REF 0.12 (0.005) T U S V K K1 T U J J1 25 0.254 (0.010) M 48 SECTION N-N B -U- L 1 N 24 A -V- PIN 1 IDENT. DETAIL E D 0.076 (0.003) -T- SEATING DIM A B C D F G H J J1 K K1 L M N F PLANE NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4. DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 5. TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 6. DIMENSIONS A AND B ARE TO BE DETERMINED AT DATUM PLANE -W-. EEE CCC CCC EEE S S M C M 0.25 (0.010) -W- DETAIL E H G MILLIMETERS MIN MAX 12.40 12.60 6.00 6.20 --- 1.10 0.05 0.15 0.50 0.75 0.50 BSC 0.37 --- 0.09 0.20 0.09 0.16 0.17 0.27 0.17 0.23 7.95 8.25 0_ 8_ INCHES MIN MAX 0.488 0.496 0.236 0.244 --- 0.043 0.002 0.006 0.020 0.030 0.0197 BSC 0.015 --- 0.004 0.008 0.004 0.006 0.007 0.011 0.007 0.009 0.313 0.325 0_ 8_ RECOMMENDED SOLDERING FOOTPRINT 48X 48X 0.32 1.00 8.45 1 0.50 PITCH DIMENSIONS: MILLIMETERS ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 http://onsemi.com 7 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC74LCX16373/D