IDT74CBTLV3244 LOW-VOLTAGE OCTAL BUS SWITCH INDUSTRIAL TEMPERATURE RANGE LOW-VOLTAGE OCTAL BUS SWITCH IDT74CBTLV3244 FEATURES: DESCRIPTION: * * * * * * * The octal bus switch has standard 244 pinouts. The CBTLV3244 is designed for asynchronous communication between data buses. Sets of four switches are controlled by one output Enable (OE). When OE is low, the set of four bus switches is on and port A is connected to port B. When OE is high, the set of four bus switches is off and a high impedance exists between port A and port B. To ensure the high-impedance state during power up or power down, both OEs should be tied to VCC through a pullup resistor. Pin-out compatible with standard '244 Logic products A/B bi-directional switch 5 Isolation under power-off conditions Over-voltage tolerant Latch-up performance exceeds 100mA VCC = 2.3V - 3.6V, Normal Range ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) * Available in QSOP and TSSOP packages APPLICATIONS: * 3.3V High Speed Bus Switching and Bus Isolation FUNCTIONAL BLOCK DIAGRAM 2 SW 1A1 1A4 8 SW 18 12 SIMPLIFIED SCHEMATIC, EACH SWITCH 1B1 1B4 B A 1 1OE OE 2A1 2A4 11 17 SW SW 9 3 2B1 2B4 19 2OE The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE JUNE 2006 1 (c) 2006 Integrated Device Technology, Inc. DSC-5393/5 IDT74CBTLV3244 LOW-VOLTAGE OCTAL BUS SWITCH INDUSTRIAL TEMPERATURE RANGE ABSOLUTE MAXIMUM RATINGS(1) PIN CONFIGURATION Symbol 1OE 20 1 VCC 1A1 2 19 2OE 2B4 3 18 1B1 1A2 4 17 2A4 2B3 5 16 1B2 1A3 6 15 2A3 2B2 7 14 1B3 1A4 8 13 2A2 2B1 9 12 1B4 10 11 2A1 GND Max Unit VCC SupplyVoltage Range Description -0.5 to +4.6 V VI Input Voltage Range -0.5 to +4.6 V 128 mA -50 mA -65 to +150 C Continuous Channel Current IIK Input Clamp Current, VI/O < 0 TSTG Storage Temperature NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. PIN DESCRIPTION Pin Names Description xOE Ax Bx QSOP/ TSSOP TOP VIEW Output Enable (Active LOW) Port A Inputs or Outputs Port B Inputs or Outputs FUNCTION TABLE(1) Input 1OE H L H L 2OE H H L L 1A, 1B I/Os 2A, 2B I/Os Disconnect Disconnect 1A Port = 1B Port Disconnect Disconnect 2A Port = 2B Port 1A Port = 1B Port 2A Port = 2B Port NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level OPERATING CHARACTERISTICS, TA = 25C(1) Symbol Parameter VCC Supply Voltage VIH High-Level Control Input Voltage VIL TA Low-Level Control Input Voltage Test Conditions Min. Max. Unit 2.3 3.6 V VCC = 2.3V to 2.7V 1.7 -- V VCC = 2.7V to 3.6V 2 -- VCC = 2.3V to 2.7V -- 0.7 VCC = 2.7V to 3.6V -- 0.8 -40 85 Operating Free-Air Temperature NOTE: 1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. 2 V C IDT74CBTLV3244 LOW-VOLTAGE OCTAL BUS SWITCH INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Operating Conditions: TA = -40C to +85C Symbol VIK II IOZ Parameter Min. Typ. Max. Unit VCC = 3V, II = -18mA -- -- -1.2 V Control Inputs VCC = 3.6V, VI = VCC or GND -- -- 1 A Data I/O VCC = 3.6V, VO = 0 or 3.6V, switch disabled -- -- 5 A VCC = 0, VI or VO = 0 to 3.6V -- -- 50 A Control Inputs, Data Inputs IOFF ICC ICC(1) Control Inputs CI Control Inputs CIO(OFF) VCC = 2.3V Typ. at VCC = 2.5V RON(2) Test Conditions VCC = 3.6V, IO = 0, VI = VCC or GND -- -- 10 A VCC = 3.6V, one input at 3V, other inputs at VCC or GND -- -- 300 A VI = 3V or 0 -- 4 -- pF VO = 3V or 0, OE = VCC VI = 0 -- -- -- -- -- -- -- 6 5 5 27 5 5 10 -- 8 8 40 7 7 15 pF IO = 64mA IO = 24mA IO = 15mA IO = 64mA IO = 24mA IO = 15mA VI = 1.7V VI = 0 VCC = 3V VI = 2.4V NOTES: 1. The increase in supply current is attributable to each current that is at the specified voltage level rather than VCC or GND. 2. This is measured by the voltage drop between the A and B terminals at the indicated current through the switch. SWITCHING CHARACTERISTICS VCC = 2.5V 0.2V Symbol tPD(1) Parameter Propagation Delay VCC = 3.3V 0.3V Min. Max. Min. Max. Unit - 0.15 - 0.25 ns 1 4.5 1 4 ns 1 4.5 1 5 ns A to B or B to A tEN Output Enable Time OE to A or B tDIS Output Disable Time OE to A or B NOTE: 1. The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance driven by an ideal voltage source (zero output impedance). 3 IDT74CBTLV3244 LOW-VOLTAGE OCTAL BUS SWITCH INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS SAME PHASE INPUT TRANSITION TEST CONDITIONS Symbol VCC(1)= 3.3V0.3V VCC(2)= 2.5V0.2V Unit VLOAD 6 2 x Vcc V VIH 3 Vcc V VT 1.5 Vcc / 2 V VLZ 300 150 mV VHZ 300 150 mV CL 50 30 pF VIN Pulse(1, 2) Generator tPHL VIH VT 0V DISABLE ENABLE CONTROL INPUT GND tPZL VOUT D.U.T. RT tPLH Propagation Delay Open 500 tPHL OPPOSITE PHASE INPUT TRANSITION VLOAD VCC tPLH OUTPUT OUTPUT SWITCH NORMALLY CLOSED LOW tPZH OUTPUT SWITCH NORMALLY OPEN HIGH 500 CL tPLZ VLOAD/2 VT tPHZ VT 0V Test Circuits for All Outputs Enable and Disable Times DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. NOTES: 1. Pulse Generator for All Pulses: Rate 10MHz; tF 2.5ns; tR 2.5ns. 2. Pulse Generator for All Pulses: Rate 10MHz; tF 2ns; tR 2.5ns. SWITCH POSITION Test Switch tPLZ/tPZL VLOAD tPHZ/tPZH GND tPD Open VIH VT 0V VOH VT VOL 4 VIH VT 0V VLOAD/2 VOL + VLZ VOL VOH VOH -VHZ 0V IDT74CBTLV3244 LOW-VOLTAGE OCTAL BUS SWITCH INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION XXX XX CBTLV IDT XX Device Type Package Temp. Range CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 Q QG PG PGG Quarter-size Small Outline Package QSOP - Green Thin Shrink Small Outline Package TSSOP - Green 3244 Low-Voltage Octal Bus Switch 74 -40C to +85C for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 5 for Tech Support: logichelp@idt.com