CN-14A-R-C1 - PANASONIC - Datasheet.Directory

Digital Pressure Sensor

For gas

DP-101(A) / 102(A) SERIES Ver. 2

panasonic.net/id/pidsx/global

2013.11

Pressure Sensor Evolutions

To Come

Certification

[DP-101(A)/102(A) only]

Conforming to

EMC Directive Recognition

Superior visibility

Improvements to the digital display deliver a wide viewing

angle along with increased clarity. The display pressure

range and set pressure range have also been increased.

Achieved further efficiency with

4 upgrades, keeping the same

operability

Improved visibility in Digital Display

Enhanced power circuitry

Addition of a reverse polarity protection circuit to the

transistor output circuit

Long-distance transmission of analog output

Users can now select either voltage output or current output as analog output according to their

application.

To prevent from breakage due to miswiring.

Addition of analog current output capability to multifunctional models

Reduced environmental impact

Thanks to a redesign of its circuitry, power consumption of

the low-power-consumption DP-100 series during normal

operation has been reduced by 14%. The display is shut

off entirely during ECO / FULL mode operation for power

savings of up to 50% compared to normal operation, and

display brightness is lowered during ECO / STD mode

operation for power savings of up to 30% compared to

normal operation.

14% lower power consumption

(during normal operation)

Old DP-100 series

840 mW (normal operation)

New DP-100 series

720 mW (normal operation)

Normal operation

720 mW

ECO / FULL operation

360 mW

14% lower

after update

Up to 50% lower

in ECO mode

Old DP-100 series New DP-100 series

Note: The upgrade will be implemented from production in October 2013, based on stock status.

Upgrade 1

Upgrade 2

Upgrade 3

Upgrade 4

SET: OrangeOFF: Green (or Red) ON: Red (or Green)

During normal operation During setting

A new global standard

Main display

Sub display

Decrement key

Increment key

Mode selection key

Comparative Output 1 operation indicator

Comparative Output 2 operation indicator

Work as analog voltage output operation

indicator in Multi-function type

Works like a dial

control type sensor

Works like a dial

control type sensor

Main

Display

Dual display allows direct

setting of threshold value

Equipped with a 30 mm 1.181 in square

compact-sized dual display. The current

value and the threshold value can be

checked at the same time, so the

threshold value can be set and checked

smoothly without switcing to another

screen mode. ON / OFF operations still

continue while the threshold values are

being set, so setting to the same

sensitivity as dial control-type sensors is

possible. Key lock function is equipped

as well.

DP-100 with dual display

Previous model with single display

Take a note on current value

Operate MODE key

Adjust threshold value Return to RUN operation

Threshold value setting method

“Current value” and “threshold value”

can be checked at the same time!

Dual Display

Direct setting

Current value

Threshold value

Simply press a button

during RUN operation Man-hours reduced by

Man-hours reduced by 3/4

3/4

3-color display (Red, Green, Orange)

The main display changes color in line with changes in the

status of output ON / OFF operation, and it also changes color

while setting is in progress. The sensor status can therefore be

understood easily, and operating errors can be reduced.

Readable digital display!

Alphanumeric indication in 12 segments is used. This improved

visual checking.

-91.8

Details copied

Details transmitted

Details received

Copy function reduces man-hours and human error

Sensors can be connected to a master sensor one by one, and a copy of the setting details for the master sensor can be transmitted as data

to other sensors. If making the same settings for multiple sensors, this prevents setting errors among other sensors and in addition, when

machinery design are changed, there would be less change in work orders.

Copy function helps operation to be accurate and quick

Setting details can be copied.

0 V

Comparative

output 1

Comparative

output 2

0 V

Comparative

output 1

Comparative

output 2

Power supply Slave sensorMaster sensor

Note: Settings cannot be copied from the new version (Ver. 2) to the old version.

However, settings can be copied from the old version to the new version (Ver. 2).

Copying via wiring

5 minutes

approx.

Sensor setting time:

5 minutes 20 seconds approx.

Sensor setting time:

20 seconds approx.

Setting man-hours are reduced and sensor setting time is shortened.

Advantage

5 minutes

approx.

5 minutes

approx.

5 minutes

approx.

5 minutes

approx.

Sensor setting time:

20 minutes approx.

1st equipment: Master

sensor

1st equipment:

2nd equipment:

3rd equipment:

4th equipment:

2nd equipment:

3rd equipment:

4th equipment:

Previously DP-100, 1st line DP-100, 2nd line

20 seconds

approx.

1st equipment:

2nd equipment:

3rd equipment:

4th equipment:

20 seconds

approx.

Number of pressure sensor: 1 unit per 1 equipment, 4 equipment per 1 line

Human operating error is reduced.

Advantage

The setting details for the master sensor are

retained, so continuous copying is possible.

For 2nd and subsequent lines, the data

transmission time only is required.

 Because all details are copied automatically, problems as a result of human error can be

prevented.

 Instruction manuals can be updated easily when changes are made to equipment design.

Reduction

of lead time

The clicking feeling is

transmitted even through gloves.

The buttons have a good clicking touch,

allowing smooth setting.

The sensor’s setting operation mode has a 3-level

configuration to suit the frequency of use.

The setting levels are clearly separated into “RUN mode” for operation

settings that are carried out daily, “MENU SETTING mode” for basic settings,

and “PRO mode” for special and detailed setting. These make setting

operations easy to understand and easy to carry out.

Displayed in orange while setting is in progress

The display appears in red and green during RUN operation, but it changes to orange while setting is in progress, so that the sensor status

can be viewed at a glance.

Default settings that can be used straight away

Easy-to-use default settings are provided for applications that are

used frequently by pressure sensors. The default settings for low

pressure types are ideal for suction confirmation applications, and

those for high pressure types are ideal for checking reference

pressure.

Setting is smooth and easy

Simple setting

Low pressure type High pressure type

Settings such as threshold value

adjustment and key lock operation

can be carried out while the

sensor is operating.

Basic settings such as output

mode setting and NO / NC

switching can be carried out.

RUN operation While setting

RUN mode

MENU SETTING mode

PRO mode

Comparative output 1

OFF

–100 kPa –

50 kPa

Hysterisys 3digits

0 kPa

Comparative output 1

0 MPa 0.5 MPa

Hysterisys 3digits

1 MPa

MENU SETTING mode

RUN mode

High-level function settings such

as hysteresis adjustment and the

copy function can be carried out.

PRO mode

The clicking feeling is

transmitted even through gloves.

Ideal for

checking

suction

Ideal for

checking

reference

pressure

Red or green when output is ON / OFF Orange while setting is in progress

Reset function

If a problem ever occurs with the sensor settings, they can be reset

to the default settings.

RUN mode

PRO mode

MENU SETTING mode

Special and

detailed setting

Special and

detailed setting

Buttons with good clicking touch

Full range of performance and functions in a compact body

Notes: 1) Hysteresis can be fixed to one of eight different levels.

“ ” or “ ” appears in the sub display for comparative

output 1, and “ ” or “ ” appears for comparative output 2.

Note: “ ” or “ ” appears in the sub display for comparative

output 1, and “ ” or “ ” appears for comparative output 2.

For low

pressure

For high

pressure

All lineup models are compound pressure

types

No sensor settings are required to switch between positive pressure

and negative pressure, so that the number of registered part

numbers can be decreased.

High performance accomplished

The low pressure type displays measurements in 0.1 kPa at a

resolution of 1/2,000 and has a response time of 2.5 ms (variable up

to 5,000 ms), ±0.5 % F.S. temperature characteristics and ±0.1 %

F.S. repeatability, achieving high detection performance.

Ideal for applications such

as suction. No mis-

operations due to vacuum

breakdown occur.

Equipped with independent dual output

Equipped with two independent comparative outputs, and separate

sensing modes can be selected for each of them. Since there are

two comparative outputs, one of the comparative outputs can even

be used for alarm output. In addition, output, which is not being

used, can be disabled. This mode is used for comparative output ON / OFF control.

EASY mode

H (Hysteresis)

H: Fixed

OFF

Comparative output

Pressure

OFF

Comparative output

H (Hysteresis)

Pressure

H: 1 digit or more

H (Hysteresis)

H: Fixed

H (Hysteresis)

Comparative output

OFF

Pressure

This mode is used for setting comparative output ON and OFF

at pressures within the setting range.

Window comparator mode

Notes: 1) Hysteresis can be fixed to one of eight different levels.

2) “ ” appears in the sub display for comparative output 1,

and “ ” appears for comparative output 2.

This mode is used for setting comparative output hysteresis to

the desired level and for carrying out ON / OFF control.

Hysteresis mode

Low pressure type

Standard type

DP-101Ƒ

DP-102Ƒ

–100 kPa 100 kPa

1 MPa

0 kPa

Ideal for applications such

as checking reference

pressure. Can also be used

for simple suction.

Resolution: 1/2,000

Response time: 2.5 ms

Temperature characteristics: ±0.5 % F.S.

Repeatability: ±0.1 % F.S.

Ɣ Vacuum breakdown can also be notified during

suction applications!

Ɣ Reference pressure alarm output is possible during

reference pressure checking!

Comparative output 1

EASY mode

Comparative output 2

EASY mode

OFF

–100 kPa

0 kPa

P-1 0 kPa P-2

Vacuum breakdown checking

Suction checking

Comparative output 1

Hysteresis

mode

Comparative output 2

EASY mode

OFF

Lo-1 Hi-1 P-2

Reference

pressure

checking

Alarm output

Displays measurements in 0.1 kPa

Three output modes are suitable for a wide

range of applications

Equipped with auto-reference / remote zero-adjustment functions,

More precise pressure management is achieved with a minimum of effort

If the reference pressure of the

device changes, two functions

are selectable. One is

auto-reference function, which

partially shift the comparative

output judgment level by the

amount that the reference

pressure shifts. The other is

remote zero-adjustment

function, which can reset the

display value to zero via

external input. These functions

are ideal for places where the

reference pressure fluctuates

wildly, or where fine settings are

required.

Multi-function type

With auto-reference function applied

–5

Comparative output: Window comparator mode

Hi-1

0, Lo-1

–5

Auto-reference input

Sets the absolute threshold level

The display remains at “30” and

only the threshold level is changed.

Threshold level before applying

auto-reference input

Trial 1

Time

Pressure

Auto-reference input value

Comparative output: Window comparator mode

Hi-1

0, Lo-1

–5

Sets the absolute threshold level

With remote zero-adjustment function applied

–5

Remote zero-adjustment input

Threshold level before applying

remote zero-adjustment input

Threshold level after applying

remote zero-adjustment input

Trial 1

Time

Pressure

Displayed when remote zero-

adjustment input is applied



–5

Without auto-reference and remote zero-adjustment functions

NG?

Comparative output: Window comparator mode

Hi-1

30, Lo-1

Fixed set value

Leak threshold level

Variation in the filling pressure

Trial 1

Trial 2

Trial 3

Time

Pressure

The display is forced to “0”, and only the

filling pressure drop range is displayed.

Threshold level after applying

auto-reference input

Because the threshold level is fixed for conventional pressure sensors,

changes in the reference pressure result in wrong decisions.

When remote zero-adjustment input is applied, the reference pressure is forced to “0”.

If the reference pressure changes to “20” or “40”, the remote zero-adjustment input

adjusts the reference pressure to “0” every time the reference pressure changes, so

any variation in the filling pressure can be ignored.

When auto-reference input is applied, the reference pressure “30” is

added to the threshold level. If the reference pressure changes to “20” or

“40”, the auto-reference input compensates for this every time by changing

the threshold level, so any variation in the filling pressure can be ignored.

Energy-saving design! Equipped with an ECO mode

This mode lowers the display luminance to cut power consumption

by approximately 30 %. The displays can also be turned off

completely to achieve a power saving of approximately 40 %.

Peak hold and Bottom hold functions

The peak values and bottom values for fluctuating pressures can be

displayed using the dual display.

Blinks alternately

Normal

Current consumption for

24 V power supply:

35 mA or less

ECO-STD

Current consumption for

24 V power supply:

25 mA or less

ECO-FULL

Current consumption for

24 V power supply:

20 mA or less

Approx.

30 % less

Approx.

40 % less

Power consumption

Other useful functions

Indicates desired values and letters

Setting details can be recognized at a glance

The DP-100 setting details appear in the digital display. Because

the settings are in numeric form that can be easily understood, it is

useful such as when receiving technical support by telephone.

1st digit: Setting status for

comparative output 1

5th digit: Response time

setting

6th digit: Display unit setting

7th digit: Display refresh rate setting

8th digit: ECO mode setting

2nd digit: Setting status for

comparative output 2

3rd digit: Threshold value setting

4th digit: Display color setting

The code on the main display is 3205.

The sub display shows 7011.

What are the check

codes for the setting?

Cable can be connected with one-touch

Connector attached cable (2m 6.562 ft), as an accessory, can be

connected easily with one-touch connection.

Types without connector attached

cable are also available

Commercially-available connectors can be used for cable

connections. Cables in required length can be used, so this

contributes to reduction in waste of unwanted cables.

Connection cable *

DP-10Ƒ-J

Environmentally

friendly

Sub display can be customized

The sub display can be set to indicate any other desired values or

letters apart from the threshold value. This eliminates the need for

tasks such as affixing a label to the device to indicate the normal

pressure value.

* Options: 1 m 3.281 ft / 3 m 9.843 ft / 5 m 16.404 ft

types are also available.

Commercially-available

parts can be used!

Commercially-available

parts can be used!

M8 plug-in connector types are also available (Only for Europe)

M8 connector

G 1/8 male thread

M5 female thread

Mating cable

CN-24A-C2 (cable length 2 m 6.562 ft)

CN-24A-C5 (cable length 5 m 16.404 ft)

DP-11Ƒ-E-P-J

Installation is also easy!

Tight installation to panels is possible

An exclusive mounting bracket that is suitable for 1 to 6 mm 0.039

to 0.236 in panel thickness is available.

Short pressure port type is lightweight and takes up little space

Space saving!

Compact size with a depth of only 30 mm 1.181 in, so that it can

easily fit into narrow spaces.

Light weight of 30 g! *

10 g lighter than standard types. This reduces the loads on movable

parts such as robot arms.

Ideal for clean environments!

Stainless steel (SUS303) which does not rust or generate gas is

used as the port material.

Space savings can also be achieved even when an L-shaped mounting bracket is used.

Front protection

cover available

MS-DP1-3

Ceiling mounting Floor mounting Rear mounting

Neat and

space

saving

Positioning bosses for easier

mounting bracket installation

* Excluding cables with connector attached

A single mounting hole!

Tight installation is possible

An exclusive mounting bracket that supports tight installation is available

Standard type

Short pressure port type

Shortened to

12.5 mm 0.492 in !

Light weight

30g approx.

Shortened to

12.5 mm 0.492 in !

Light weight

30g approx.

Elbow joint

Short pressure

port type DP-10Ƒ-M

30 mm

1.181 in

* The illustration shows connection using an elbow joint. The elbow joint is sold separately.

M5 female thread+R1 8 male thread

M5 female thread [Material: Stainless steel (SUS)]

 MS-DP1-1  MS-DP1-5

DP-100

ORDER GUIDE

Accessory

CN-14A-C2

(Connector attached cable 2 m 6.562 ft)

Type without connector attached cable

Type without connector attached cable CN-14A-C2 is available. When ordering this type, suffix “-J” to the end of Model No.

(e.g.) Type without connector attached cable of DP-101-N is “DP-101-N-J”

Standard pressure port type Short pressure port type

Asia

Europe

Asia North America

Standard

Multi-function

Standard

Multi-function

For low pressure

For high pressure

For low pressure

For high pressure

For low pressure

For high pressure

For low pressure

For high pressure

Standard

Multi-function

For low pressure

For high pressure

For low pressure

For high pressure

Rated pressure range Model No. Pressure portType

NPN open-collector transistor

PNP open-collector transistor

NPN open-collector transistor

PNP open-collector transistor

NPN open-collector transistor

PNP open-collector transistor

NPN open-collector transistor

PNP open-collector transistor

NPN open-collector transistor

PNP open-collector transistor

NPN open-collector transistor

PNP open-collector transistor

NPN open-collector transistor

PNP open-collector transistor

NPN open-collector transistor

PNP open-collector transistor

NPN open-collector transistor

PNP open-collector transistor

M5 female thread

R 1/8

male thread

M5 female thread

G 1/8

male thread

M5 female thread

G 1/8

male thread

í100.0 to +100.0 NPa

í0.100 to +1.000 MPa

í100.0 to +100.0 NPa

í0.100 to +1.000 MPa

í100.0 to +100.0 NPa

í0.100 to +1.000 MPa

í100.0 to +100.0 NPa

í0.100 to +1.000 MPa

í100.0 to +100.0 NPa

í0.100 to +1.000 MPa

í100.0 to +100.0 NPa

í0.100 to +1.000 MPa

Comparative output

DP-101

DP-102

DP-101A

DP-102A

DP-101-E-P

DP-102-E-P

DP-101A-E-P

DP-102A-E-P

DP-111-E-P-J

DP-112-E-P-J

DP-111A-E-P-J

DP-112A-E-P-J

DP-101-N

DP-101-N-P

DP-102-N

DP-102-N-P

DP-101A-N

DP-101A-N-P

DP-102A-N

DP-102A-N-P

DP-101-M

DP-101-M-P

DP-102-M

DP-102-M-P

DP-101A-M

DP-101A-M-P

DP-102A-M

DP-102A-M-P

Appearance

* CN-14A-C2

(

Connector attached

cable 2 m 6.562 ft

)

is attached.

(

Excluding M8 plug-in

connector type

)

Standard

Multi-function

For low pressure

For high pressure

For low pressure

For high pressure

M8 plug-in connector type

Standard

Multi-function

For low pressure

For high pressure

For low pressure

For high pressure

í100.0 to +100.0 NPa

í0.100 to +1.000 MPa

í100.0 to +100.0 NPa

í0.100 to +1.000 MPa

í100.0 to +100.0 NPa

í0.100 to +1.000 MPa

í100.0 to +100.0 NPa

í0.100 to +1.000 MPa

M5 female thread

NPT 1/8

male thread

Flat installation on the wall by shifting the direction

of the pressure port

By mounting the flat attachment

to DP-10

-M(-P), pressure port

and cable can now be pulled out

in downward, left or right

directions. Flat mounting on

surfaces such as the wall is

made possible.

For short pressure port type For short pressure port type

Rc1/8 conversion bushing is available. Compatible

with previous model

By equipping the push-in converter with DP-10

-M(-P), pressure

port can be converted from M5 female thread to Rc1/8

female thread.

Bore diameter conversion to the DP2 / DP3 series is possible.

MS-DP1-7

M5 female thread Rc1/8

female thread

Conversion bushing

Flat attachment

3 possible directions to mount

06'3)Ƒ

20 mm

0.787 in pitch

Previous model

Model No. Pressure port

MS-DP1-FM

MS-DP1-FR

MS-DP1-FN

MS-DP1-FE

M5 female thread

Rc1/8 female thread

NPT1/8 female thread

G1/8 female thread

Previous model DP2 / DP3

series can be switched over to

DP-100 series.

20 mm

0.787 in pitch

DP-100

Connector attached cable

&1$&Ƒ

&1$5&Ƒ

Panel mounting bracket, Front protection cover

MS-DP1-2

MS-DP1-3

Flat attachment

MS-DP1-FM MS-DP1-FR

MS-DP1-FN

MS-DP1-FE

MS-DP1-4

Recommended connector

Contact: SPHD-001T-P0.5, Housing: PAP-04V-S

(Manufactured by J.S.T. Mfg. Co., Ltd.)

Note: Contact the manufacturer for details of the recommended products.

Recommended crimping tool

Model No.: YC-610R

(Manufactured by J.S.T. Mfg. Co., Ltd.)

Note: Contact the manufacturer for details of the recommended products.

OPTIONS

M8 connector attached cable

&1$&Ƒ

MS-DP1-5

ø9

ø0.354 (Unit: mm in)

31.4

1.236 ø4

ø0.157

Note: The connector attached cable CN-14A-C2 is supplied with the DP-100 series.

(Excluding M8 plug-in connector type).

Sensor mounting bracket

MS-DP1-1

Conversion bushing

MS-DP1-7

Sensor mounting

bracNet

MS-DP1-1

M3 (length 6 mm 0.236 in)

screws with washers

Accessory for

MS-DP1-1

()

Front protection cover

MS-DP1-3

Panel mounting bracNet

MS-DP1-2

DP-100

Panel mounting bracNet MS-DP1-4

DP2-20

ñ101.3kPa

OUT2OUT1

MODE

0-ADJ

DP2 / DP3

Insert

Remove

Mounting holes

for DP2 / DP3 series

can be used as is.

Front protection cover

DPX-04 (optional)

can be installed on

MS-DP1-4.

Sensor mounting

bracNet

MS-DP1-5

M3 (length 6 mm 0.236 in)

screws with washers

Accessory for

MS-DP1-5

()

MS-DP1-FM 15g approx.

MS-DP1-FR/FN/FE 25g approx.

Net weight:

Two M3 (length 8 mm 0.315 in) screws,

two M4 (length 20 mm 0.787 in) screws are attached.

Conversion bushing

MS-DP1-7

M5 female

thread

Rc1/8

female

thread

Connector

attached cable

Connector

attached cable

(Flexible cable)

M8 connector

attached cable

Connector

Panel mounting

bracNet

Front protection

cover

Conversion

bushing

Flat

attachment

Sensor

mounting

bracNet

Length: 1 m 3.281 ft

Length: 2 m 6.562 ft

Length: 3 m 9.843 ft

Length: 5 m 16.404 ft

Length: 1 m 3.281 ft

Length: 2 m 6.562 ft

Length: 3 m 9.843 ft

Length: 5 m 16.404 ft

Length: 2 m 6.562 ft

Length: 5 m 16.404 ft

Set of 10 housings and 40 contacts

Model No.Designation Description

CN-14A-C1

CN-14A-C2

(Note)

CN-14A-C3

CN-14A-C5

CN-14A-R-C1

CN-14A-R-C2

CN-14A-R-C3

CN-14A-R-C5

CN-24A-C2

CN-24A-C5

CN-14A

MS-DP1-1

MS-DP1-5

MS-DP1-2

MS-DP1-4

MS-DP1-3

MS-DP1-7

MS-DP1-FM

MS-DP1-FR

MS-DP1-FN

MS-DP1-FE

0.2 mm

4-core cabtyre cable with

connector on one end

Cable outer diameter:

3.7 mm

0.146 in

0.2 mm

4-core flexible cabtyre cable

with connector on one end

Cable outer diameter:

3.7 mm

0.146 in

For M8 plug-in connector type

The connector on one end

Cable outer diameter: ø4 mm ø0.157 in

Allows sensors to be installed on the flooring or ceiling.

Multiple sensors can also be mounted closely.

Allows sensors to be installed on the wall. Multiple sensors

can also be mounted closely.

Allows installation to panels with thicNness of 1 to 6 mm 0.039

to 0.236 in. Multiple sensors can also be mounted closely.

Allows replacement from DP2 / DP3 series to DP-100 series. For newly designed

set-up, please use panel mounting bracNet MS-DP1-2 for panel mounting.

Protects the adjustment surfaces of sensors.

(Can be attached when using the panel mounting bracNet)

Pressure port and cable can now be

pulled out in downward, left or right

directions. Flat mounting on surfaces

such as the wall is made possible.

By equipping with DP-10

-M(-P), pressure port can be converted to

Rc1/8 female thread. Replacement from DP2 / DP3 series is possible.

M5 female thread

/8 female thread

NPT1/8 female thread

G1/8 female thread

DP-100

SPECIFICATIONS

Asia (NPN output), North America (NPN output)

ON voltage: 0.4 V DC or less

OFF voltage: 5 to 30 V DC, or open

,nput impeGance: 0 Nȍ appro[.

Input time: 1 ms or more

Asia (PNP output), Europe, North America (PNP output)

ON voltage: 5 V to

V DC

OFF voltage: 0.6 V DC or less, or open

Input impeGance: 10 Nȍ appro[.

Input time: 1 ms or more

Output voltage: 1 to 5 V DC

Zero point: within 3 V

5 % F.S.

Span: within 4 V ±5 % F.S.

Linearity: within ±1 % F.S.

Output impeGance: 1 Nȍ appro[.

Output voltage: 0.6 to 5 V

Zero point: within 1 V

5 % F.S.

Span: within 4.4 V ±5 % F.S.

Linearity: within ±1 % F.S.

Output impeGance: 1 Nȍ appro[.

Output current: 4 to 20 mA

Zero point: 12 mA ±5 % F.S.

Span: 16 mA ±5 % F.S.

Linearity: within ±1 % F.S.

LoaG resistance: 250 ȍ (ma[.)

Output current: 2.4 to 20 mA

Zero point: 4 mA ±5 % F.S.

Span: 17.6 mA ±5 % F.S.

Linearity: within ±1 % F.S.

LoaG resistance: 250 ȍ (ma[.)

(

Comparative output 1 operation indicator, comparative output 2 operation indicator:

Lights up when each comparative output is ON

)

Orange LED Orange LED

(

Comparative output 1 operation indicator: Lights up when comparative output is ON,

Analog voltage output operation indicator: Lights up when setting

)

Environmental resistance

í1.030 to +1.030 kgf/cm2

í1.010 to +1.010 bar

í14.64 to +14.64 psi

í757 to +757 mmHg

í29.8 to 29.8 inHg

Standard

For low pressure For high pressure

Multi-function

For low pressure For high pressure

í100.0 to +100.0 kPa

í101.0 to +101.0 kPa

í0.100 to +1.000 MPa í100.0 to +100.0 kPa í0.100 to +1.000 MPa

500 kPa 1.5 MPa 500 kPa 1.5 MPa

DP-101(-M)(-P)DP-102(-M)(-P)DP-101A(-M)(-P)DP-102A(-M)(-P)

DP-101-E-P DP-102-E-P DP-101A-E-P DP-102A-E-P

DP-111-E-P-J DP-112-E-P-J DP-111A-E-P-J DP-112A-E-P-J

DP-101-N(-P)DP-102-N(-P)DP-101A-N(-P)

Gauge pressure Type of pressure

Rated pressure range

Set pressure range

Pressure withstandability

Applicable fluid

Selectable unit

Supply voltage

Power consumption

Comparative output

Output operation / Output modes

Hysteresis

Repeatability

Response time

Short-circuit protection

E[ternal input (Note 3)

Auto-reference function /

Remote zero-adjustment

function

Analog voltage output (Note 3)

Analog current output (Note 3)

Display

Displayable pressure range

Indicator

Protection

Ambient temperature

Ambient humidity

Voltage withstandability

Insulation resistance

Vibration resistance

Shock resistance

Temperature characteristics

Pressure port

Material

Connecting method / Cable length

Weight

Accessories

Non-corrosive gas

For low pressure: kPa, kgf/cm2, bar, psi, mmHg, inHg, For high pressure: MPa, kPa, kgf/cm2, bar, psi

12 to 24 V DC ±10 % Ripple P-P 10 % or less

Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)

ECO mode: 480 mW or less at STD (Current consumption 20 mA or less at 24 V supply voltage)

360 mW or less at FULL (Current consumption 15 mA or less at 24 V supply voltage)

NPN open-collector transistor

 Ma[imum sink current: 100 mA



Applied voltage: 30 V DC or less (between comparative output and 0 V)

 Residual voltage: 2 V or less (at 100 mA sink current)

PNP open-collector transistor

 Ma[imum source current: 100 mA



Applied voltage: 30 V DC or less (between comparative output and +V)

 Residual voltage: 2 V or less (at 100 mA source current)

NO / NC (selectable by key operation) / EASY mode / Hysteresis mode / Window comparator mode

Minimum 1 digit (variable) (however, 2 digits when using psi unit)

±0.2 % F.S. (within ±2 digits) ±0.1 % F.S. (within ±2 digits) ±0.2 % F.S. (within ±2 digits)±0.1 % F.S. (within ±2 digits)

2.5 ms, 5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms, 500 ms, 1,000 ms, 5,000 ms, selectable by key operation

Incorporated

4 digits + 4 digits 3-color LCD display (Display refresh rate: 250 ms, 500 ms, 1,000 ms, selectable by key operation)

IP40 (IEC)

í10 to +50 °C +14 to +122 °F, Storage: í10 to +60 °C +14 to +140 °F

35 to 85 % RH (No dew condensation or icing allowed), Storage: 35 to 85 % RH

1,000 V AC for one min. between all supply terminals connected together and enclosure

50Mȍ or more with 500 V DC megger between all supply terminals connected together and enclosure

10 to 500 Hz frequency, 3 mm 0.118 in amplitude, in X, Y and Z directions for two hours each (when panel is mounted: 10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude, in X, Y and Z directions for two hours each)

100 m/s2 acceleration (10 G appro[.) in X, Y and Z directions for three times each

Within ±1 % F.S. (at +20 °C +68 °F)

Within ±0.5 % F.S. (at +20

C +68

Within ±1 % F.S. (at +20 °C +68 °F)

Within ±0.5 % F.S. (at +20

C +68

Asia: M5 female thread + R (PT) 1/8 male thread >e[cluding DP-Ƒ-M(-P)], Europe: M5 female thread + G 1/8 male thread, North America: M5 female thread + NPT 1/8 male thread

Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Stainless steel (SUS303) , Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber

Connector / Total length up to 100 m 328.084 ft (less than 30 m 98.425 ft when conforming to CE marking) is possible with 0.3 mm

, or more, cable

Net weight: 40 g appro[. (DP-10Ƒ-M(-P): 30 g appro[.), Gross weight: 135 g appro[. (DP-10Ƒ-M(-P):125 g appro[.)

CN-14A-C2 (Connector attached cable 2 m 6.562 ft): 1pc. (e[cluding M8 plug-in connector type)

DP-102A-N(-P)

Model No.

í101 to +1,010 kPa

í1.03 to +10.30 kgf/cm2

í1.01 to +10.10 bar

í14.6 to +146.4 psi

í0.101 to +1.010 MPa

í101 to +1,010 kPa

í1.03 to +10.30 kgf/cm2

í1.01 to +10.10 bar

í14.6 to +146.4 psi

í0.101 to +1.010 MPa

í1.030 to +1.030 kgf/cm2

í1.010 to +1.010 bar

í14.64 to +14.64 psi

í757 to +757 mmHg

í29.8 to 29.8 inHg

í101.0 to +101.0 kPa

í1.030 to +1.030 kgf/cm2

í1.010 to +1.010 bar

í14.64 to +14.64 psi

í757 to +757 mmHg

í29.8 to 29.8 inHg

í101.0 to +101.0 kPa

í101 to +1,010 kPa

í1.03 to +10.30 kgf/cm2

í1.01 to +10.10 bar

í14.6 to +146.4 psi

í0.101 to +1.010 MPa

í101 to +1,010 kPa

í1.03 to +10.30 kgf/cm2

í1.01 to +10.10 bar

í14.6 to +146.4 psi

í0.101 to +1.010 MPa

í1.030 to +1.030 kgf/cm2

í1.010 to +1.010 bar

í14.64 to +14.64 psi

í757 to +757 mmHg

í29.8 to 29.8 inHg

í101.0 to +101.0 kPa

Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of +20 °C +68 °F.

Model Nos. of Asia type having “-M´ are short pressure port type. Model Nos. of Asia and North America types having the suffi[ “-P” are PNP output type.

3) Cannot be used at the same time.

Type

Asia (Note 2)

Europe

M8 plug-in connector type

North America (Note 2)

Item

DP-100

I/O CIRCUIT AND WIRING DIAGRAMS

I/O circuit diagram

Symbols  D : Reverse supply polarity protection diode

D1, ZD2 : Surge absorption zener diode

r1, Tr2 : NPN output transistor

Symbols  D : Reverse supply polarity protection diode

D1, ZD2 : Surge absorption zener diode

r1, Tr2 : PNP output transistor

12 to 24 V DC

10 %

(Black) Comparative output 1

Load

(White) Comparative output 2

Tr1

ZD2

ZD1

Tr2

100 mA ma[.

(Blue) 0 V

Terminal Designation

Comparative output 1

Standard type: Comparative output 2

Multi-function type: Analog output or E[ternal input

0 V

Terminal arrangement diagram

Terminal Designation

Comparative output 1

Standard type: Comparative output 2

Multi-function type: Analog output or E[ternal input

0 V

Terminal arrangement diagram

Standard type

2 3 4

Users’ circuitInternal circuit

Sensor circuit

Terminal No.

Color code of connector attached cable

(Brown) +V

Symbols  D1, D2 : Reverse supply polarity protection diode

D1 : Surge absorption zener diode

r1 : PNP input transistor

r2 : NPN output transistor

Multi-function type

Symbols  D1, D2 : Reverse supply polarity protection diode

D1: Surge absorption zener diode

r1 : PNP output transistor

r2 : NPN input transistor

Multi-function type

NPN output type

DP-10Ƒ

PNP output type

DP-10Ƒ-P

Users’ circuitInternal circuit

12 to 24 V DC

10 %

Load

Tr1

ZD2

ZD1

Tr2

100 mA ma[.

(Blue) 0 V

Sensor circuit

Terminal No.

Color code of connector attached cable

(Black)

Comparative output 1

(White) Comparative output 2

(Brown) +V

1kȍ

Users’ circuitInternal circuit

12 to 24 V DC

10 %

(White) Analog output

or E[ternal input Load

(Black)

Comparative output 1

(Brown) +V

Tr1

ZD1

Tr2

100 mA ma[.

(Blue) 0 V

Sensor circuit

Terminal No.

Color code of connector attached cable

1kȍ

Users’ circuitInternal circuit

ZD1

12 to 24 V DC

10 %

(White) Analog output

or E[ternal input Load

(Black)

Comparative output 1

(Brown) +V

Tr1

Tr2

(Blue) 0 V

Sensor circuit

100 mA ma[.

Terminal No.

Color code of connector attached cable

DP-100

I/O CIRCUIT AND WIRING DIAGRAMS

PRECAUTIONS FOR PROPER USE

Never use this product as a sensing device for

personnel protection.

In case of using sensing devices for personnel

protection, use products which meet laws and standards,

such as OSHA, ANSI or IEC etc., for personnel

protection applicable in each region or country.

The DP-100 series is designed for use with non-corrosive

gas. It cannot be used with liquid or corrosive gas.



Wiring

Make sure that the power supply is off while wiring.

Verify that the supply voltage variation is within the rating.

If power is supplied from a commercial switching regulator, ensure

that the frame ground (F.G.) terminal of the power supply is

connected to an actual ground.

In case noise generating equipment (switching regulator, inverter

motor, etc.) is used in the vicinity of this sensor, connect the frame

ground (F.G.) terminal of the equipment to an actual ground.

Do not run the wires together with high-voltage lines or power lines or put

them in the same raceway. This can cause malfunction due to induction.

Incorrect wiring will cause problems with operation.



Connection

Do not apply stress directly to the

connection cable leader or to the

connector.



Connector

attached cable

[CN-14A(-R)-CƑ]

Conditions in use for CE conformity

The DP-100 series is a CE conformity product complying with

EMC Directive. The harmonized standard with regard to immunity

that applies to this product is EN 61000-6-2 and the following

condition must be met to conform to that standard.



The MS-DP1-2 panel mounting bracket (optional) and the MS-DP1-3

front protection cover (optional) are also available.



Condition

Mounting

The line to connect with this sensor should be less than

30 m 98.425 ft.



MS-DP1-1 / MS-DP1-5 sensor mounting brackets are available

separately, and it should be used for mounting. When tightening

the sensor to the sensor mounting bracket, use a tightening torque

of 0.5 N·m or less.



Sensor mounting bracket

MS-DP1-1 (Optional)

M3 (length 6 mm 0.236 in)

screws with washers

Accessory for MS-DP1-1

and MS-DP1-5

PNP output type

'3Ƒ(3-

Terminal Designation

0 V

Standard type: Comparative output 2

Multi-function type: Analog output or External input

Comparative output 1

Terminal arrangement diagram

I/O circuit diagram

12 to 24 V DC

10 %

(Black) Comparative output 1

Load

(White) Comparative output 2

Tr1ZD2

ZD1

Tr2100 mA max.

100 mA max.

(Blue) 0 V

Standard type

Users’ circuitInternal circuit

Sensor circuit

Terminal No.

Color code of connection cable

(Brown) +V

1 k

ZD1

(White) Analog voltage output

or External input

Load

(Black)

Comparative output 1

Tr1

Tr2

100 mA max.

Multi-function type

Users’ circuitInternal circuit

12 to 24 V DC

10 %

(Brown) +V

(Blue) 0 V

Sensor circuit

Terminal No.

Color code of connection cable

Symbols D : Reverse supply polarity protection diode

D1, ZD2 : Surge absorption zener diode

r1, Tr2 : PNP output transistor

Symbols D1, D2 : Reverse supply polarity protection diode

D1: Surge absorption zener diode

r1 : PNP output transistor

r2 : NPN input transistor

Front protection cover

MS-DP1-3

(optional)

Panel mounting bracket

MS-DP1-2

(optional)

( )

DP-100

14 mm 0.551 in

spanner

PRECAUTIONS FOR PROPER USE

①Decide the direction of this product to mount with the sensor.

②Mount this product with the M3 female threads of the sensor by

using the attached M3 (length 8 mm 0.315 in) screws. The

tightening torque should be 0.5 N·m or less.

③Mount this product with the mounting surface by using the

attached M4 (length 20 mm 0.787 in) screws. The tightening

torque should be 1.2 N·m or less.

Note: It is not possible to mount this product such

that the pressure port faces upward.

Note: Take care that if the cable with connector is sticking out of the side

groove of this product when mounting, the cable may disconnected.

Note: Do not tighten the pressure port by holding the product with the

spanner. It may cause the product breakage.

PipingMounting

If connecting a commercially-available

coupling to the pressure port, attach a

12 mm 0.472 in spanner (14 mm 0.551 in

spanner for DP-100-E type) to the hexagonal

section of the pressure port to secure it, and

tighten at a torque of 9.8 N·m or less. If it is

tightened using excessive torque, it may

damage the coupling or the pressure port.

In addition, wrap sealing tape around the

coupling when connecting it to prevent leaks.

The MS-DP1-4 panel mounting bracket is available when

switching from the DP2 / DP3 series.



An conversion bushing is available for when using the DP-10Ƒ-M short

pressure port type. It can be used to switch between this model and the

DP2 / DP3 series. When connecting to the pressure port, use a tightening

torque of 1.0 N·m or less.



The MS-DP1-FƑ flat attachment is available.

If using the MS-DP1-FƑ flat attachment (optional), install by

following the procedures given below.



12 mm 0.472 in

spanner

Flat attachment

Make sure to mount MS-DP1-FƑ with the sensor properly. If it is

not mounted properly, air leakage may occur.

Take care that the excessive mounting and dismounting of this

product may cause deterioration of the O-ring.

If you touch the O-ring of MS-DP1-FƑ, or any scratch or dust, etc.

is attached to it, air leakage may occur and the sensing

performance may deteriorate.

Take sufficient care when using and storing MS-DP1-FƑ.

The tightening torque should be 1 N·m or less when connecting a

coupling to the pressure port of MS-DP1-FM.

If connecting a commercially-available joint to the pressure port of

the DP-10Ƒ-M, hold the main unit in your hand to steady it, and

tighten to a torque of 1.0 N·m or less. If it is tightened to an

excessive torque, the joint or the main unit may become

damaged.

If connecting a commercially-available joint to the pressure port of

the MS-DP1-7, tighten to a torque of 9.8 N·m or less.

When connecting the coupling to the pressure port of

MS-DP1-FR/FE/FN, hold the pressure port with a 14 mm 0.551 in

spanner and make sure that the tightening torque is 9.8 N·m or

less.

In addition, in order to prevent any leakage, wind a sealing tape

on the coupling when connecting.

Pressure port

faces downward Pressure port

faces leftward Pressure port

faces rightward

Pressure port

faces upward

M3 (length 8 mm 0.315 in)

screw (Accessory)

M3 female thread

Connector attached cable

Groove

M4 (length 20 mm 0.787 in)

screw (Accessory)

Coupling (Purchase separately.)

Pressure port

14 mm 0.551 in

spanner

DP2-20

ñ101.3kPa

OUT2

OUT1

MODE

$'-

Front protective cover

DPX-04 (Optional)

can be installed on

MS-DP1-4.

DP2 / DP3

DP-100

Insert

Remove

Panel mounting bracket MS-DP1-4

Conversion bushing MS-DP1-7

M5 female thread Rc 1 8 female thread

Mounting holes

for DP2 / DP3 series

can be used as is.

DP-100

PRECAUTIONS FOR PROPER USE

PRO mode

Setting item Description

Reset setting

ECO mode setting

Linked display color

switching

(standard type only)

Display refresh rate

switching

Hysteresis fix value

switching

Setting check code

Setting copy mode

Table of codes

—

————

—

—ADJ.

NO OFF

OFF

P-1, Lo-1

NC NO Hi-1

NO NC

P-2, Lo-2

NC NO Hi-2

NO NC

NC NO

EASY

Analog voltage output /

External input

NO / NC

switching

Comparative output 2

output mode

Comparative output 1

output mode

NO / NC

switching

Display color for

main display

Threshold

value display

Display

color linking

Code

2.5 ms MPa 250 ms OFF

5 ms kPa 500 ms STD

10 ms kgf/cm21,000 ms FULL

25 ms bar

50 ms psi

100 ms mmHg

250 ms inchHg

500 ms

1,000 ms

5,000 ms

Code

If the mode selection key is pressed and held for 5 seconds in

RUN mode, the mode will switch to PRO mode.

If the mode selection key is pressed while a setting is being made,

the mode will switch to RUN mode. In this case, the settings that

have been changed will be entered.





Sub display switching Changes the information in the sub display

during RUN mode operation to the desired

alphanumeric display.

Changes the display refresh rate for the

pressure value displayed in the main display.

Sets the hysteresis for EASY mode and window

comparator mode. (8 steps)

Allows the display color for the main display to

be switched in line with the output operation for

comparative output 1 or comparative output 2.

Allows power consumption to be reduced by

dimming the display or turning it off.

Allows the setting details to be checked via

codes.

Allows the setting details for the master sensor

to be copied to slave sensors.

Resets the settings to the factory settings.

1st digit 2nd digit 3rd digit 4th digit

Standard

type only

Multi-function

type

Standard type

Hysteresis

Red

when ON

Comparative

output 1

Comparative

output 2

Comparative

output 1

Comparative

output 2

Comparative

output 1

Comparative

output 2

Comparative

output 1

Comparative

output 2

Green

when ON

Always

red

Always

green

Analog voltage

output

Auto-

reference

Remote

zero-adjustment

Analog current

output

Window

comparator

Window

comparator

5th digit 6th digit 7th digit 8th digit

Response time Unit switching

Display refresh rate

ECO mode

If the mode selection key is pressed and held for 2 seconds in

RUN mode, the mode will switch to MENU SETTING mode.

If the mode selection key is pressed while a setting is being made,

the mode will switch to RUN mode. In this case, the settings that

have been changed will be entered.



Others

RUN mode

MENU SETTING mode

This product has been developed / produced for industrial use.

Use within the rated pressure range.

Do not apply pressure exceeding the pressure withstandability

value. The diaphragm will get damaged and correct operation shall

not be maintained.

Do not use during the initial transient time (0.5 sec. approx.) after

the power supply is switched on.

Avoid dust, dirt, and steam.

Take care that the sensor does not come in direct contact with

water, oil, grease, or organic solvents, such as, thinner, etc.

Do not insert wires, etc., into the pressure port. The diaphragm will

get damaged and correct operation shall not be maintained.

Do not operate the keys with pointed or sharp objects.



7KLVLVWKHQRUPDORSHUDWLQJPRGH

Comparative output 1

output mode setting

Setting item Description

Sets the output mode for comparative output 1.

Unit switching Pressure unit can be changed.

NO / NC switching

Response time setting

Comparative output 2 output mode

setting (standard type only)

Sets the output mode for comparative output 2.

Display color switching

for main display

Analog output / external

input switching

(multi-function type only)

Allows the color for the main display to be changed.

The colors can be set to ‘red / green’ or ‘green / red’

to correspond to ON / OFF output, or it can be fixed

at ‘red’ or ‘green’ all the time.

Sets the response time.

The response time can be selected from 2.5 ms,

5 ms, 10 ms, 25 ms, 50 ms, 100 ms, 250 ms,

500 ms, 1,000 ms and 5,000 ms.

Sets normally open (NO) or normally closed (NC).

Allows switching between analog voltage output /

analog current output, and auto-reference input /

remote zero-adjust-ment input.

Setting item Description

Threshold value

setting

Zero-adjustment

function

Key lock function

Peak hold /

bottom hold function

Stops key operations from being accepted.

The threshold values for ON / OFF operation can be changed directly

by pressing the increment key (UP) and the decrement key (DOWN).

This forces the pressure value display to be reset to zero when

the pressure port is open on the atmospheric pressure side.

Displays the peak value and bottom value for fluctuating

pressure. The peak value appears in the main display,

and the bottom value appears in the sub display.

—

DP-100

Sensor

DP-10

Sensor

DP-10Ƒ-M(-P)

0.787

M3 female thread, 4 0.157 deep

M5 female thread

0.472

Connector

1.5

0.059

1.181

1.181 9.5

0.374

42.5

1.673 7.5

0.295

R (PT) 1/8

male thread

(North America: NPT 1/8)

25.5

1.004

DIMENSIONS (Unit: mm in)The CAD data in the dimensions can be downloaded from the website.

Europe

G 1/8

male thread

0.394 7

0.276

0.551

Europe

1.181 ø8.3

ø0.327

1.5

0.059

4.5

0.177

1.181

25.5

1.004

1.181

0.787

M3 female thread,

4 0.157 deep

connector

M5 female thread,

4 0.157 deep

Sensor

DP-11Ƒ-E-P--

1.181

47.5

1.870 7

0.276

25.5

1.004

0.591 7

0.276

1.5

0.059

G 1/8 male thread

9.5

0.374

4.5

0.177

M3 female thread,

4 0.157 deep

M5 female thread

M8 connector

0.787

0.551

DP-100

The CAD data in the dimensions can be downloaded from the website.

Assembly dimensions

Mounting drawing with '3Ƒ

Panel mounting bracket (Optional), Front protection cover (Optional)

MS-DP1-2

MS-DP1-3

Panel cut-out dimensions

34.5

1.358 20

0.787

34.5

1.358

39.3

1.547

Note: The panel thickness should be

1 to 6 mm 0.039 to 0.236 in.

When “n” units are installed horizontally in series When “n” units are installed vertically in series

Note: The panel thickness should be

1 to 6 mm 0.039 to 0.236 in.

When 1 unit is installed

31 1.220 Xn + 3.5 0.138 X (n-1)

55 2.165

or more

31 1.220 Xn + 3.5 0.138 X (n-1)

55 2.165

or more

31 0

í

31 0

í

31 0

í

31 0

í

1.220

í0.016

1.220 0

í0.016

1.220 0

í0.016

1.220 0

í0.016

DIMENSIONS (Unit: mm in)

Material: POM (Panel mounting bracket)

Polycarbonate (Front protection cover)

Material: Cold rolled carbon steel (SPCC)

(Uni-chrome plated)

Two M3 (length 6 mm 0.236 in) screws with washers are attached.

Sensor mounting bracket (Optional)

MS-DP1-1

Sensor mounting bracket (Optional)

MS-DP1-5

Assembly dimensions

Mounting drawing with DP-1Ƒ

4.2

0.165

9.5

0.374

2-R2.1 R0.083

0.866

14.5

0.571

25.5

1.004

4.2

0.165

9.5

0.374

14.5

0.571

2-R2.1 R0.083

ø2.3

ø0.091

0.039

0.866

t 2

t 0.079 20

0.787

5.5

0.217

1.732

R13

R0.512

0.512

0.787

1.181

0.787

2-ø3.5 ø0.138

5.3

0.209

( )

0.591

1.181

1.181 45

1.772

7.5

0.295

1.5

0.059

9.5

0.374

t 2

t 0.079

1.181

42.5

1.673

0.472

( )

8.7

0.343

7.2

0.283

0.433

9.5

0.374

7.5

0.295

Panel thickness dimension

1 to 6 mm 0.039 to 0.236 in

18.3

0.720

33.4

1.315

1.969

33.4

1.315

M3 female thread,

4 0.157 deep

Connector

Front

protection

cover

M5 female thread,

4 0.157 deep

(52 2.047 max)

0.472

R(PT) 1/8

male thread

0.787

4.5

0.177

28.5

1.122

49.5

1.949

ø4.5

ø0.177

49.5

1.949

1.181

29.5

1.161

53.5

2.106

1.5

0.059

4.5

0.177

1.181

R6.75

R0.266

0.630

ø8.3

ø0.327

t 1.5

t0.059

1.102

0.787

Material: Cold rolled carbon steel (SPCC)

(Uni-chrome plated)

Two M3 (length 6 mm 0.236 in) screws with washers are attached.

Assembly dimensions

Mounting drawing with DP-1Ƒ-M

22.75

0.896

0.787

29.5

1.161

0.787

13.5

0.531

4.5

0.177

44.5

1.752

1.181

1.102

t 1.5

t 0.059

8.5

0.335

ø4.5

ø0.177

2-ø3.5 ø0.138

0.787

View A

DP-100

The CAD data in the dimensions can be downloaded from the website.

DIMENSIONS (Unit: mm in)

Assembly dimensions

Mounting drawing with DP-10Ƒ

Panel mounting bracket (Optional)

MS-DP1-4

Assembly dimensions

Mounting drawing with DP-10Ƒ-M

Flat attachment (Optional)

MS-DP1-FM

Material: Panel mounting bracket body  Nylon 6

Panel mounting bracket  Stainless steel (SUS304)

Spacer  Cold rolled carbon steel (SPCC)(Uni-chrome plated)

Panel cut-out dimensions

Spacer

Connector

M5 female

thread

0.472

1.181

1.575

42.7

1.681

( )

0.118

1.417

6.5

0.256

26.5

1.043

9.7

0.382

( )

42.7

1.681

Panel thickness dimension 1 to 3.2 mm

0.039 to 0.126 in

0.315

Front protection cover (DPX-04)

Panel mounting

bracket body

Panel mounting

bracket

R 1/8

male thread

2.205

3.150

1.417

+0.5

0.020

1.417

+0.5

0.020

1.575

Material: EnclosurePolybutylene

terephthalate (PBT)

(Glass fiber reinforced)

Pressure portStainless steel

(SUS303)

O-ringHydrogenated Nitrile

Butadiene Rubber

(H-NBR)

Weight: 15 g approx. (flat attachment only)

Two M3 (length 8 mm 0.315 in) screws,

two M4

(length 20 mm 0.787 in) screws are

attached.

M5 female thread

8.5 0.335

Conversion bushing (Optional)

MS-DP1-7

Material: Brass (Nickel plated)

Weight: 10 g approx.

3.5

0.138 7.8

0.307

0.315

11 0.433 10 0.394

0.551

M5 male thread

Gasket

1/8

female thread

0.5

0.020

( )

15.8

0.622

Assembly dimensions

Mounting drawing with DP-10Ƒ-M

Flat attachment (Optional)

MS-DP1-FR/FN/FE

5.5 0.217

6.5 0.256

0.787

5.5 0.217

6.5 0.256

44.5

1.752

0.945

44.5

1.752

2-ø4.3 ø0.169

11.5

0.453

1.457

17.5

0.689

0.433

1.181

0.945

1.181

( )

Note: The panel tickness should be 1 to 32 mm 0.039 to 1.260 in.

Material: Enclosure

Polybutylene terephthalate (PBT)

(Glass fiber reinforced)

Pressure port

Stainless steel (SUS303)

O-ringHydrogenated Nitrile

Butadiene Rubber (H-NBR)

Weight: 25 g approx. (flat attachment only)

Two M3 (length 8 mm 0.315 in) screws, two M4

(length 20 mm 0.787 in) screws are attached.

1.457

0.433

8.5

0.335

17.5

0.689

11.5

0.453

Note: MS-DP1-FR has a

Rc1/8 female thread.

MS-DP1-FN has a

NPT1/8 female thread.

Pressure port

female thread (Note)

0.787

0.551

13.5

0.531

Product distinguishing mark

MS-DP1-FR: 0 line

MS-DP1-FN: 1 line

MS-DP1-FE: 2 line

52.5

2.067

( )

0.945

( )

1.181 24

0.945

2-ø4.3

ø0.169

52.5

2.067

1.181

0.945

Model No. Cable length L (mm in)

1,000 39.370

2,000 78.740

3,000 118.110

5,000 196.850

CN-14A(-R)-C1

CN-14A(-R)-C2

CN-14A(-R)-C3

CN-14A(-R)-C5

Connector attached cable (Optional, CN-14A-C2 is attached to the sensor)

CN-14A(-R)-CƑ

1.378

0.315

1.969

ø3.7 ø0.146 cable

( )

0.315

( )

DIMENSIONS (Unit: mm in)The CAD data in the dimensions can be downloaded from the website.

Please contact ..........

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan

Global Sales Department

■Telephone: +81-568-33-7861 ■Facsimile: +81-568-33-8591

panasonic.net/id/pidsx/global

Specifications are subject to change without notice. Printed in JapanNo. CE-DP100V2-5 November, 2013