Toll Free: (888) SEI-SEIS www.seielect.com email: marketing@seielect.com
1
(888) 734-7347
RPC Series — Resistor Pulse Chip
Features
• Excellent pulse withstanding performance • Stability class: 5%
• Improved working voltage • Broad resistance range
• Higher anti-surge performance compared
with RMC series
• RoHS compliant/ lead-free available
Electrical Specifications
Type
Power Rating
(Watts)
@ 70°C
Maximum
Working
Voltage
Isolation
Voltage
Resistance Temperature
Coefficient
Ohmic Range and Tolerance
5% 10%
RPC 0805 0.100 150V 500V ±200 ppm/°C 0.27Ω – 22M 0.27Ω – 22M
RPC 1206 0.125 200V 500V ±200 ppm/°C 0.27Ω – 22M 0.27Ω – 22M
RPC 1210 0.250 200V 500V ±200 ppm/°C 0.27Ω – 22M 0.27Ω – 22M
RPC 2010 0.500 200V 500V ±200 ppm/°C 0.27Ω – 22M 0.27Ω – 22M
RPC 2512 1.000 200V 500V ±200 ppm/°C 0.27Ω – 22M 0.27Ω – 22M
How to Order
RPC 0805 10M 5% A
SEI Type Code Nominal Resistance Tolerance Packaging
Code Tolerance Values Code Description SEI Types Pkg Qty
0805 5% E24 R Bulk All 1,000
1206 10% E24 G Paper RPC 0805, RPC 1206 5,000
1210 20% E24 AEmboss
RPC 1210, RPC 2010,
RPC 2512 4,000
2010
2512
Toll Free: (888) SEI-SEIS www.seielect.com email: marketing@seielect.com
RPC Series — Resistor Pulse Chip
2
(888) 734-7347
Mechanical Specifications
Type L
Body Length
W
Body Width
H
Body Height
a
Top Termination
b
Bottom Termination Units
RPC 0805 0.079 ± 0.004
2.00 ± 0.10
0.049 ± 0.004
1.25 ± 0.10
0.021 ± 0.004
0.55 ± 0.10
0.012 ± 0.008
0.30 ± 0.20
0.016 ± 0.008
0.40 ± 0.20
inches
mm
RPC 1206 0.126 ± 0.006
3.20 ± 0.15
0.063 ± 0.006
1.60 ± 0.15
0.021 ± 0.004
0.55 ± 0.10
0.012 ± 0.008
0.30 ± 0.20
0.020 ± 0.010
0.50 ± 0.25
inches
mm
RPC 1210 0.126 ± 0.006
3.20 ± 0.15
0.098 ± 0.006
2.50 ± 0.15
0.021 ± 0.006
0.55 ± 0.15
0.012 ± 0.008
0.30 ± 0.20
0.020 ± 0.010
0.50 ± 0.25
inches
mm
RPC 2010 0.197 ± 0.006
5.00 ± 0.15
0.098 ± 0.006
2.50 ± 0.15
0.021 ± 0.006
0.55 ± 0.15
0.012 ± 0.008
0.30 ± 0.20
0.024 ± 0.008
0.60 ± 0.20
inches
mm
RPC 2512 0.248 ± 0.006
6.30 ± 0.15
0.126 ± 0.006
3.20 ± 0.15
0.021 ± 0.006
0.55 ± 0.15
0.012 ± 0.008
0.30 ± 0.20
0.024 ± 0.008
0.60 ± 0.20
inches
mm
Climatic Category
RPC 2010 & RPC 2512 RPC 0805, RPC 1206, & RPC 1210
Lower Category Temperature -55°C -55°C
Upper Category Temperature +125°C +155°C
Duration of the Damp heat, Steady-State Test 56 days 56 days
Performance Characteristics
Test Test Results Test Methods (JIS C 520-1:1198)
Voltage Proof No breakdown or flashover R ≥ 1G
ohm Clause 4.7 500Va.c.,60s
Variation of Resistance
with Temperature See ratings table Clause 4.8 +20°C/ -55°C/ +20°C/ +125°C/ +20°C : RPC 2010 RPC 2512
+20°C/ -55°C/ +20°C/ +155°C/ +20°C : RPC 0805 RPC 1206 RPC 1210
Overload ∆R ≤ ± 1% + 0.05Ω
No visible damage, legible markings
Clause 4.13 The applied voltage shall be 2.5 times of the rated voltage or twice of the limiting
element voltage, whichever is the less severe, 2s.
Solderability In accordance with Clause 4.17.4.5 Clause 4.17 235°C, 2s.
Resistance to Soldering
Heat ∆R ≤ ± 1% + 0.05ΩClause 4.18 After immersion into the flux, the immersion into solder shall be carried out in
Solder bath at 260°C for 5s.
Rapid Change of
Temperature
∆R ≤ ± 1% + 0.05Ω
No visible damage
Clause 4.19 Cycle: -55°C/ + 125°C 5 times: RPC 2010 RPC 2512
Cycle: -55°C/ +155°C 5 times: RPC 0805 RPC 1206 RPC 1210
Climatic Sequence ∆R ≤ ± 5% + 0.10Ω
No visible damage
Clause 4.23 Dry/Damp heat (12+12h cycle), first cycle./
Cold/Damp heat (12+12h cycle), remaining cycle./ D.C. Load
Damp Test, Steady
State
∆R ≤ ± 5% + 0.10Ω
No visible damage, legible markings Clause 4.24 40°C, 95% R.H., 56 days, test a) and b) of Clause 4.24.2.1
Endurance @ 70°C ∆R ≤ ± 5% + 0.10Ω
No visible damage Clause 4.25.1 Rated voltage, 1.5h "ON", 05.h "OFF", 70°C, 1,000h
Endurance at the Upper
Category Temperature
∆R ≤ ± 5% + 0.10Ω
No visible damage
Clause 4.25.3 125°C, no load, 1,000h: RPC 2010 RPC 2512
155°C, no load, 1,000h: RPC 0805 RPC 1206 RPC 1210
Adhesion No visible damage Clause 4.32 5N, 10s
Bend of Strength of the
Face Plating ∆R ≤ ± 1% + 0.05ΩClause 4.33 Amount of bend: 3mm RPC 0805 RPC 1206 RPC 1210
Amount of bend: 1mm RPC 2010 RPC 2512
