VSI, HER601 THRU HER608 Voltage Range Features @ Low forward voltage drop @ High current capability @ High reliability e High surge current capability Mechanical Data Cases:Molded plastic e Epoxy:UL 94V-0 rate flame retardant e Lead:Axial leads,solderable per MIL- STD-202,Method 208 guaranteed @ Polarity:Color band denotes cathode end e High temperature soldering guaranteed: 250C/10 seconds/.375",(9.5mm) lead lengths at 5 Ibs.,(2.3kg) tension @ Weight:1.65 grams 6.0 AMPS. HIGH EFFICIENT 50 to 1000 Volts RECTIFIERS Current 6.0 Amperes R-6 36(9.1) 1.0(25.4) 34(8.6) MIN. DIA. Ly le | .360(9.1) 340(8.6) 1.0(25.4) MIN. .052(1.3) o4a(1.2) || DIA. l Dimensions in inches and (millimeters) For capacitive load, derate current by 20% MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25C ambient temperature unless otherwise specified. Single phase, half wave, 60HZz, resistive or inductive load. Type Number HER601| HER602| HER603/ HER604| HER605| HER606] HER607| HER608) UNITS Maximum Repetitive Peak Reverse Voltage Vrrm| 50 100 200 300 400 600 800 1000 | vy Maximum RMS Voltage VRMs} 35 70 140 210 280 420 560 700 Vi Maximum DC Blocking Voltage Voc] 50 100 200 300 400 600 800 1000 Vv Maximum Average Forward Rectified Current .375"(9.5mm) Lead Length @TA = 55C IF(av) 6.0 A Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load | |rsm 200 A (JEDEC method) Goon Instantaneous Forward Voltage Ve 1.0 | 13 | 17 V Maximun DC Reverse Current @ TA= 25 Ir 10.0 uA at Rated DC Blocking Volage @ TA=100C 200 uA Maximum Reverse Recovery Time (Note 1) TRR 50 75 ns Typical Junction Capacitance (Note 2) Cy 100 65 pF Operating Temperature Range Ts -55 to+150 c Storage Temperature Range TsTG -55 to+150 c NOTES: 1. Reverse Recovery Test Conditions: IF=0.5A,IR=1.0A,IRR=0.25A 2.Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C.RATING AND CHARACTERISTIC CURVES HER601 THRU HER608 TS, 50Q 102 NONINDUCTIVE NONINDUCTIVE +0.5A ) but (+) PULSE 0 = 50Vde GENERATOR) (approx) (NOTE 2) -0.25A ) \ OSCILLOSCOPE 210 (NOTE1) (+) NON INDUCTIVE NOTES:1. Rise Time=7ns max. Input Impedance= > -1.0A 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms FIG.3-TYPICAL REVERSE CHARACTERISTICS 1000 o Tj=100C INSTANTANEOUS REVERSE CURRENT. (#A) b 3 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE.(%) FIG.4-MAXIMUM NON-REPETITIVE SURGE CURRENT PEAK FORWARD SURGE CYRRENT.(A) 1000 1 10 100 NUMBER OF CYCLES AT 60Hz | tomb sey TIME BASE FOR INSTANTANEOUS FORWARD CURRENT.(A) FIG.2-MAXIMUM AVERAGE FORWARD CURRENT DERATING FIG.1- REVERSE RECOVER TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM oe wo 4 Single Phase \ Half Wave 60Hz \ 2 | Resistive or Inductive Load \ L 0.375" (9.5mm) Lead Length 1s 25 50 75 100 125 150 175 AMBIENT TEMPERATU: RE.(C) AVERAGE FORWARD CURRENT. (A) 5/ 10ns/ cm FIG.5-TYPICAL FORWARD CHARACTERISTICS S o o .01 2 4 6 8 1.0 1.2 1.4 FORWARD VOLTAGE.(V) FIG.6-TYPICAL JUNCTION CHARACTERISTICS JUNCTION CAPACITANCE.(pF) a3 388 2 8 eo FF 6 aA SG a N a A 5 1 2 5 100 200 500 800 10 20 50 REVERSE VOLTAGE.(V)