8 7 6 3 4 5 ZONE REV ALL OPEN L-SERIES BACKPLANE MODULE ASSEMBLY PART NUMBER ASSIGNMENT 327 - X 0 X X - 0 X X 6 D LOAD 5 = STANDARD LOAD 7 = CUSTOM LOAD, LEADED 8 = CUSTOM LOAD, LEAD FREE L = CUSTOM LOAD, LEADED, ADVANCED PLATING N = CUSTOM LOAD, LEAD FREE, ADVANCED PLATING MINIMUM PIN WIPE 3 = 1.00 4 = 2.00 5 = 3.00 ASSEMBLY PART NUMBER K (L) P 327-X010-00X 4 9 (7.40) 9.10 327-X005-00X ASSEMBLY PART NUMBER C (16.65) TABLE 2 SIGNAL CONTACT 327-50XX-0X3 170-0003- 6 327-50XX-0X5 170-0005- 6 327-50XX-0X4 18.35 A CSAS-743R3H.VER01 DESCRIPTION B CSAS-83MHBL.VER01 ADDED NEW PART NUMBERS FOR NEW PLATING CODES IN ASSEMBLY PART NUMBER ASSIGNMENT TREE MODIFIED NOTE 4 AND 6. C DSMH-96LQUR.VER03 NOTE 7 ADDED DCOY-A85NWY.VER01 BY NEW RELEASE 1 REV DATE D APPROVED M.DEROSA 06/12/2007 HCL-MH 03/03/2010 C.SAMMIS HCL-NS 05/20/2013 D.SMITH UPDATED PART MARKING REQUIREMENTS HCL-SD D.SMITH D.COVEY 04/20/2016 D ISOMETRIC BOTTOM VIEW SCALE 2/1 ISOMETRIC VIEW SCALE 2/1 K X 1.85 = (L) SEE TABLE 1 TOTAL NUMBER OF SIGNAL CONTACTS 55 110 10X 1.85 = (18.50) (24.76) MINIMUM WIPE LENGTH INITIAL ENGAGEMENT 3.00mm 170-0004- 6 C-327-5000-500 SCR NUMBER D SH 2 LENGTH, SEE DETAIL U mm WIPE mm WIPE mm WIPE 4 PLATING CODE 0 = 735 4=804 1 = 732 5=803 2 = 769 6=806 3 = 768 7=805 NUMBER OF COLUMNS 05 = 5 COLUMN MODULE 10 = 10 COLUMN MODULE TABLE 1 SHT1, A8 DRW NO. 4.00mm DAUGHTERCARD 5.00mm (DAUGHTERCARD PCB REFERENCE) DAUGHTERCARD WAFER P 3 (DAUGHTERCARD WAFER REFERENCE) SEE DWG C-314-5000-500 TOP VIEW BACKPLANE SHOWN ONLY SCALE 2/1 -XX3 = (3.55) -XX4 = (4.55) -XX5 = (5.55) C (BACKPLANE INSULATOR TOP REFERENCE) ROW A (BACKPLANE TOP SURFACE REFERENCE) NON NOTCH SIDE B SCALE 4/1 2.04 FROM TOP OF DC PCB TO 0.00 OFFSET FROM DC COLUMN TO BP COLUMN DETAIL U SCALE 6/1 18.0 WHEN FULLY MATED B 7 NOTES: SEE DETAIL 1. REFER TO TB-2085 FOR GbX PRODUCT SPECIFICATIONS. U BACKPLANE BLADE BACKPLANE 2. NOTCH DESIGNATES "ROW A" SIDE OF SHROUD. NOTCH FEATURE ON OPPOSITE SIDE FROM PART MARKING. 3. SEE TB-2325 FOR PART MARKING REQUIREMENTS. 16.2 K X 1.85 = (L) 735 - Ni SULFAMATE, STANDARD GOLD, LEADED C-327-5000-500 4. 9th DIGIT OF PART NUMBER IDENTIFIES PLATING. (1.00) MIN BOARD 24.76 MEASURED AT THE BOTTOM DRW NO. (0.85) 2.64 (2.28) TAIL LENGTH 732 - Ni SULFAMATE, HIGH GOLD, LEADED 769 - Ni SULFAMATE, STANDARD GOLD, LEAD-FREE 768 - Ni SULFAMATE, HIGH GOLD, LEAD-FREE 804 - NANO Ni, STANDARD GOLD, LEADED 803 - NANO Ni, HIGH GOLD, LEADED 806 - NANO Ni, STANDARD GOLD, LEAD-FREE 805 - NANO Ni. HIGH GOLD, LEAD-FREE 5. FOR REPAIR PROCEDURE FOR BLADE, SEE TB-2099. 0.00 ANGLES INTERPRET PER ASME Y14.5M CODE IDENT 31413 7 M.DEROSA CHK 02/11/04 APVD 02/11/04 T.DO T.DO UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MM, DECIMAL MARKER IS A PERIOD 7. 0.25MM TOE-IN IS ACCEPTABLE WHEN MEASURE AT THE TOP OF EACH SIDE WALL. 8 07/14/03 6 5 4 3 CUSTOMER USE DRAWING 2 A Division of Amphenol Corporation 200 Innovative Way, Nashua, NH 03062 603.879.3000 TITLE OPEN BACKPLANE MODULE REV 6. IF 4TH DIGIT OF THE PART NUMBER IS 7 OR 8 OR L OR N (CUSTOM PART). DIGIT 5 THROUGH 10 DO NOT FOLLOW THE PARADIGM IN TABLE. DRAWN Amphenol TCS M.DEROSA D 0.000 07/14/03 SH 0.0 DESIGN 1 A TOLERANCES 4 PAIR GbX L-SERIES PART NO. REV SEE TABLE 1 N/A DRAWING NO. C-327-5000-500 ASSEM SIZE D REV P1045-CU-BP-SHRD-OPEN C-327-5000-500 DRAWING SCALE 2/1 D 1.8 C.1 SHEET 1 OF 2 1 8 7 6 3 4 5 DRW NO. ZONE REV SH C-327-5000-500 SCR NUMBER DESCRIPTION BY SEE SHEET 1 2 REV DATE D APPROVED D D 0.51 [0.018] TYP 8 0.41 X Y 0 (24.76) 9 18.50 16.65 11.10 9.25 Y 7.40 1.85 0 (24.76) 5.55 3.13 14.80 9 3.70 0.51 [0.018] TYP8 0.41 X Y 12.95 Y COLUMN 10 18.50 16.65 14.80 12.95 11.10 9.25 7.40 5.55 1.85 3.70 3.13 C 9 (18.35) COLUMN 5 9 (9.10) COLUMN 4 4 X 1.85 = (7.40) X 0 0.85 COLUMN 8 COLUMN 7 9 X 1.85 COLUMN 3 COLUMN 5 COLUMN 2 COLUMN 4 COLUMN 1 COLUMN 3 COLUMN 2 X COLUMN 1 0 (3.70) A1 B COLUMN 6 = (16.65) (1.85) (1.85) C COLUMN 9 0.85 A1 5 POSITION GBX-L SERIES BACKPLANE HOLE PATTERN COMPONENT SIDE SHOWN SCALE (1.85) (1.85) (3.70) B 10 POSITION GBX-L SERIES BACKPLANE HOLE PATTERN COMPONENT SIDE SHOWN 6/1 SCALE 6/1 DRW NO. C-327-5000-500 TOLERANCES 0.00 ANGLES 9. SEE DOCUMENT 190-0002-000 FOR TOOLING KEEPOUT ZONES. INTERPRET PER ASME Y14.5M CODE IDENT 31413 7 CHK 02/11/04 APVD 02/11/04 T.DO T.DO UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MM, DECIMAL MARKER IS A PERIOD 8. STATED PAD SIZE MAY REQUIRE FILLETING. FOR DETAILED ROUTING GUIDELINES, SEETB-2090. 8 M.DEROSA 6 5 4 3 CUSTOMER USE DRAWING 2 A Division of Amphenol Corporation 200 Innovative Way, Nashua, NH 03062 603.879.3000 TITLE OPEN BACKPLANE MODULE REV NOTES: 07/14/03 D 0.000 DRAWN Amphenol TCS M.DEROSA SH A 07/14/03 2 0.0 DESIGN 4 PAIR GbX L-SERIES PART NO. REV SEE TABLE 1 N/A DRAWING NO. C-327-5000-500 ASSEM SIZE D REV P1045-CU-BP-SHRD-OPEN C-327-5000-500 DRAWING SCALE 3/1 D 1.8 C.1 SHEET 2 OF 2 1