8
8
DD
C
B
A
B
C
1
23
4
5
67
76543
Amphenol TCS
A Division of Amphenol Corporation
200 Innovative Way, Nashua, NH 03062 603.879.3000
( )
TAIL LENGTH
2.28
( )0.85
K X 1.85 = (L)
N/A
OPEN L-SERIES BACKPLANE MODULE
ASSEMBLY PART NUMBER ASSIGNMENT
327 - X 0 X X - 0 X X
LOAD
5 = STANDARD LOAD
7 = CUSTOM LOAD, LEADED
8 = CUSTOM LOAD, LEAD FREE
L = CUSTOM LOAD, LEADED, ADVANCED PLATING
N = CUSTOM LOAD, LEAD FREE, ADVANCED PLATING
NUMBER OF COLUMNS
05 = 5 COLUMN MODULE
10 = 10 COLUMN MODULE
MINIMUM
PIN WIPE LENGTH, SEE DETAIL U
3 = 1.00 mm WIPE
4 = 2.00 mm WIPE
5 = 3.00 mm WIPE
PLATING CODE
0 = 735 4=804
1 = 732 5=803
2 = 769 6=806
3 = 768 7=805
4
TABLE 1
ASSEMBLY
PART NUMBER K (L) P TOTAL NUMBER OF
SIGNAL CONTACTS
327-X005-00X 4 (7.40) 9.10 55
327-X010-00X 9 (16.65) 18.35 110
TABLE 2
ASSEMBLY
PART NUMBER
SIGNAL
CONTACT
MINIMUM
WIPE LENGTH
327-50XX-0X3 170-0003- 3.00mm
327-50XX-0X4 170-0004- 4.00mm
327-50XX-0X5 170-0005- 5.00mm
APPROVEDDATEBYDESCRIPTIONSCR NUMBERREVZONE
D.SMITH06/12/2007M.DEROSANEW RELEASECSAS-743R3H.VER01AALL
C.SAMMIS03/03/2010HCL-MH
ADDED NEW PART NUMBERS FOR NEW PLATING CODES
IN ASSEMBLY PART NUMBER ASSIGNMENT TREE
MODIFIED NOTE 4 AND 6.
CSAS-83MHBL.VER01B
D.SMITH05/20/2013HCL-NSNOTE 7 ADDEDDSMH-96LQUR.VER03CSHT1, A8
D.COVEY
04/20/2016HCL-SDUPDATED PART MARKING REQUIREMENTSDCOY-A85NWY.VER01D
DESIGN 07/14/03
M.DEROSA
DRAWN 07/14/03
M.DEROSA
CHK 02/11/04
T.DO
APVD 02/11/04
T.DO
DRW NO. SH REV
C-327-5000-500 1 D
DRW NO. SH REV
C-327-5000-500 1 D
UNLESS OTHERWISE SPECIFIED DIMENSIONS
ARE IN MM, DECIMAL MARKER IS A PERIOD
INTERPRET PER ASME Y14.5M
CUSTOMER USE
DRAWING
CODE IDENT 31413
TOLERANCES
0.0
0.00
0.000
ANGLES
TITLE
OPEN BACKPLANE MODULE
4 PAIR GbX L-SERIES
PART NO. REV
SEE TABLE 1
DRAWING NO. REV
C-327-5000-500 D
ASSEM P1045-CU-BP-SHRD-OPEN
DRAWING C-327-5000-500
1.8
C.1
SIZE D SCALE 2/1 SHEET 1 OF 2
NOTES:
1. REFER TO TB-2085 FOR GbX PRODUCT SPECIFICATIONS.
2. NOTCH DESIGNATES "ROW A" SIDE OF SHROUD. NOTCH FEATURE ON OPPOSITE SIDE FROM PART MARKING.
3. SEE TB-2325 FOR PART MARKING REQUIREMENTS.
4. 9th DIGIT OF PART NUMBER IDENTIFIES PLATING.
735 - Ni SULFAMATE, STANDARD GOLD, LEADED
732 - Ni SULFAMATE, HIGH GOLD, LEADED
769 - Ni SULFAMATE, STANDARD GOLD, LEAD-FREE
768 - Ni SULFAMATE, HIGH GOLD, LEAD-FREE
804 - NANO Ni, STANDARD GOLD, LEADED
803 - NANO Ni, HIGH GOLD, LEADED
806 - NANO Ni, STANDARD GOLD, LEAD-FREE
805 - NANO Ni. HIGH GOLD, LEAD-FREE
5. FOR REPAIR PROCEDURE FOR BLADE, SEE TB-2099.
6. IF 4TH DIGIT OF THE PART NUMBER IS 7 OR 8 OR L OR N (CUSTOM PART). DIGIT 5 THROUGH 10 DO NOT FOLLOW THE PARADIGM IN TABLE.
7. 0.25MM TOE-IN IS ACCEPTABLE WHEN MEASURE AT THE TOP OF EACH SIDE WALL.
INITIAL ENGAGEMENT
(DAUGHTERCARD PCB
REFERENCE)
(DAUGHTERCARD
WAFER REFERENCE)
SEE DWG C-314-5000-500
ROW A
ISOMETRIC BOTTOM VIEW
SCALE 2/1
ISOMETRIC VIEW
SCALE 2/1
TOP VIEW
BACKPLANE SHOWN ONLY
SCALE 2/1
SCALE 4/1
NON NOTCH SIDE
SEE DETAIL
U
DETAIL U
SCALE 6/1
(BACKPLANE INSULATOR
TOP REFERENCE)
(BACKPLANE TOP
SURFACE REFERENCE)
BACKPLANE BLADE
BACKPLANE
DAUGHTERCARD
DAUGHTERCARD
WAFER
6
6
6
6
2
3
FROM TOP OF DC PCB TO
2.04
16.2
2.64
18.0 WHEN
FULLY MATED
( ) MIN
BOARD
1.00
-XX3 = (3.55)
-XX4 = (4.55)
-XX5 = ( )5.55
P
10X 1.85 = ( )18.50
( )24.76
K X 1.85 = (L)
SEE TABLE 1
0.00 OFFSET FROM DC
COLUMN TO BP COLUMN
MEASURED AT THE
BOTTOM
24.76
7
8
8
DD
C
B
A
B
C
1
23
4
5
67
76543
Amphenol TCS
A Division of Amphenol Corporation
200 Innovative Way, Nashua, NH 03062 603.879.3000
( )24.76
( )9.10
3.13
4 X 1.85
= ( )7.40
9 X 1.85 = ( )16.65
( )1.85 ( )1.85
( )3.70
( )1.85
( )1.85
( )3.70
N/A
NOTES:
8. STATED PAD SIZE MAY REQUIRE FILLETING. FOR DETAILED ROUTING GUIDELINES, SEE TB-2090.
9. SEE DOCUMENT 190-0002-000 FOR TOOLING KEEPOUT ZONES.
5 POSITION GBX-L SERIES BACKPLANE HOLE PATTERN
COMPONENT SIDE SHOWN
SCALE 6/1
COLUMN 1
COLUMN 2
COLUMN 3
COLUMN 4
COLUMN 5
A1
0
9
9
DESIGN 07/14/03
M.DEROSA
DRAWN 07/14/03
M.DEROSA
CHK 02/11/04
T.DO
APVD 02/11/04
T.DO
DRW NO. SH REV
C-327-5000-500 2 D
DRW NO. SH REV
C-327-5000-500 2 D
UNLESS OTHERWISE SPECIFIED DIMENSIONS
ARE IN MM, DECIMAL MARKER IS A PERIOD
INTERPRET PER ASME Y14.5M
CUSTOMER USE
DRAWING
CODE IDENT 31413
TOLERANCES
0.0
0.00
0.000
ANGLES
TITLE
OPEN BACKPLANE MODULE
4 PAIR GbX L-SERIES
PART NO. REV
SEE TABLE 1
DRAWING NO. REV
C-327-5000-500 D
ASSEM P1045-CU-BP-SHRD-OPEN
DRAWING C-327-5000-500
1.8
C.1
SIZE D SCALE 3/1 SHEET 2 OF 2
APPROVEDDATEBYDESCRIPTIONSCR NUMBERREVZONE
SEE SHEET 1
10 POSITION GBX-L SERIES BACKPLANE HOLE PATTERN
COMPONENT SIDE SHOWN
SCALE 6/1
COLUMN 1
COLUMN 2
COLUMN 3
COLUMN 4
COLUMN 5
COLUMN 6
COLUMN 7
COLUMN 8
COLUMN 9
COLUMN 10
A1
0
9
9
8
83.13
( )24.76
0.85
( )18.35
0.85
0
18.50
0
1.85
3.70
5.55
7.40
9.25
11.10
12.95
14.80
16.65
[0.018] TYP
X Y
0.51
0.41
[0.018] TYP
X Y
0.51
0.41
0
18.50
0
1.85
3.70
5.55
7.40
9.25
11.10
12.95
14.80
16.65
X
Y
X
Y
