Data Sheet April 2008 MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Features n n n The MH005-Series Power Modules use advanced, surfacemount technology and deliver high-quality, compact, dc-dc conversion at an economical price. Applications n Distributed power architectures n Communication equipment n Computer equipment Small size: 50.8 mm x 27.9 mm x 11.7 mm (2.00 in. x 1.10 in. x 0.46 in.) Wide 3:1 input range Operating ambient temperature range: -10 C to +70 C, no derating n High reliability n High efficiency: 73% typical n Input-to-output isolation n No external filtering required n No heat sink required n Overcurrent protection n Output overvoltage protection n PC board mountable n n UL* 1950 Recognized, CSA C22.2 No. 950-95 Certified, VDE 0805 (EN60950, IEC950) Licensed Meets FCC Class A requirements * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. Options n Long pins: 5.8 mm 0.5 mm (0.230 in. 0.020 in.) n Metal case with case ground pin Description The MH005-Series Power Modules are dc-dc converters that operate over an input voltage range of 4.5 Vdc to 14 Vdc and provide precisely regulated dc outputs. The outputs are isolated from the inputs, allowing versatile polarity configurations and grounding connections. The modules have maximum power ratings of 5 W with a typical full-load efficiency of 73%. The modules are PC board mountable and encapsulated in nonconductive cases. The modules are rated to full load at 100 C case temperature with no external filtering or heat sinking. MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Symbol Min Max Unit Input Voltage (continuous) VI -- 15 Vdc Operating Case Temperature (See Thermal Considerations section.) TC -10 100 C Storage Temperature Tstg -40 110 C I/O Isolation Voltage (1 minute) -- -- 500 Vdc Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Table 1. Input Specifications Parameter Symbol Min Typ Max Unit VI 4.5 5 14 Vdc II, max -- -- 2.5 A Inrush Transient i2t -- -- 0.2 A2s Input Reflected-ripple Current, Peak-to-peak (5 Hz to 20 MHz, 500 nH source impedance, TA = 25 C; see Figure 15 and Design Considerations section.) II -- 45 -- mAp-p Input Ripple Rejection (120 Hz) -- -- 50 -- dB Operating Input Voltage Maximum Input Current (VI = 0 V to 14 V; IO = IO, max; see Figure 1.) Fusing Considerations CAUTION: This power module is not internally fused. An input line fuse must always be used. This encapsulated power module can be used in a wide variety of applications, ranging from simple stand-alone operation to an integrated part of a sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a normal-blow fuse with a maximum rating of 5 A in series with the input (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer's data for further information. 2 Lineage Power MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Electrical Specifications (continued) Table 2. Output Specifications Parameter Output Voltage Set Point (VI = 5 V; IO = IO, max; TA = 25 C) Device Symbol Min Typ Max Unit MH005A MH005B MH005C MH005BK VO, set VO, set VO, set VO1, set VO2, set VO1, set VO2, set 4.85 11.64 14.55 11.40 -11.40 14.25 -14.25 5.0 12.0 15.00 12.00 -12.00 15.00 -15.00 5.15 12.36 15.45 12.60 -12.60 15.75 -15.75 Vdc Vdc Vdc Vdc Vdc Vdc Vdc VO VO VO VO1 VO2 VO1 VO2 4.75 11.40 14.25 10.80 -10.80 13.50 -13.50 -- -- -- -- -- -- -- 5.25 12.60 15.75 13.20 -13.20 16.50 -16.50 Vdc Vdc Vdc Vdc Vdc Vdc Vdc MH005A, B, C MH005A, B, C MH005A, B, C -- -- -- -- -- -- 0.02 0.05 0.6 0.1 0.2 1.5 %VO %VO %VO MH005A, B, C MH005BK, CL MH005A, B, C MH005BK MH005CL -- -- -- -- -- -- -- -- -- -- 3 15 -- -- -- 15 50 50 200 250 mVrms mVrms mVp-p mVp-p mVp-p MH005A MH005B MH005C MH005BK IO IO IO IO1 IO2 IO1 IO2 0.05* 0.02* 0.02* 0.01* 0.01* 0.01* 0.01* -- -- -- -- -- -- -- 1.0 0.42 0.33 0.21 0.21 0.17 0.17 A A A A A A A MH005CL Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life; see Figures 17 and 18.) MH005A MH005B MH005C MH005BK MH005CL Output Regulation: Line (VI = 4.5 Vdc to 14 Vdc) Load (IO = IO, min to IO, max) Temperature (TC = -10 C to +100 C) Output Ripple and Noise Voltage (See Figure 16.): RMS Peak-to-peak (5 Hz to 20 MHz) Output Current MH005CL * At less than the minimum current, units will continue to operate; however, the single-output modules (MH005A, B, C) may exceed their output ripple specification. The dual-output modules (MH005BK, CL) may exceed their output voltage regulation limits if the output currents are severely imbalanced with one output sourcing less than the minimum current. Lineage Power 3 MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Electrical Specifications (continued) Table 2. Output Specifications (continued) Parameter Device Symbol Min Typ Max Unit Output Current-limit Inception (See Figures 4--9.): VO = 4.5 V (~0.9 VO, set) VO = 10.8 V (~0.9 VO, set) VO = 13.5 V (~0.9 VO, set) VO1 or VO2 = 10.2 V VO1 or VO2 = 12.75 V MH005A MH005B MH005C MH005BK MH005CL IO IO IO IO IO -- -- -- -- -- 1.5 0.7 0.6 0.7 0.6 2.5 1.0 0.9 1.2 1.1 A A A A A Output Current Limit (VI = 5 V, TA = 25 C; See Figures 4--9.): VO = 1.0 V (~0.2 VO, set) VO = 1.0 V (~0.08 VO, set) VO = 1.0 V (~0.07 VO, set) VO1 or VO2 = 1.0 V VO1 or VO2 = 1.0 V MH005A MH005B MH005C MH005BK MH005CL -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 3.5 2.5 2.5 2.5 2.5 A A A A A Output Short-circuit Current (VO = 250 mV; see Figures 4--9.) MH005A MH005B MH005C MH005BK MH005CL -- -- -- -- -- -- -- -- -- -- 3.0 1.4 1.4 1.3 1.3 -- -- -- -- -- A A A A A Efficiency (VI = 5 V; IO = IO, max; TA = 25 C; see Figures 10, 11, 17, and 18.) MH005A MH005B MH005C MH005BK MH005CL 70 70 70 70 70 72 73 73 73 73 -- -- -- -- -- % % % % % All -- -- 400 -- kHz All All -- -- -- -- 60 4 -- -- mV ms All All -- -- -- -- 60 4 -- -- mV ms Switching Frequency Dynamic Response (yIO/yt = 1 A/10 s, VI = 5 V, TA = 25 C; see Figures 12 and 13.): Load Change from IO = 50% to 75% of IO, max: Peak Deviation Settling Time (VO < 10% peak deviation) Load Change from IO = 50% to 25% of IO, max: Peak Deviation Settling Time (VO < 10% of peak deviation) * At less than the minimum current, units will continue to operate; however, the single-output modules (MH005A, B, C) may exceed their output ripple specification. The dual-output modules (MH005BK, CL) may exceed their output voltage regulation limits if the output currents are severely imbalanced with one output sourcing less than the minimum current. Output not in current limit is held at minimum load to give the worst-case (highest current level) inception point. 4 Lineage Power MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Electrical Specifications (continued) Table 3. Isolation Specifications Parameter Min Typ Max Unit Isolation Capacitance -- 1200 -- pF Isolation Resistance 10 -- -- M3/4 Min Typ Max Unit 113 (4.0) g (oz.) General Specifications Parameter Calculated MTBF (IO = 80% of IO, max; TC = 40 C) Weight 5,000,000 -- -- hours Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions and Design Considerations for further information. Parameter Output Overvoltage Protection (clamp) Device Symbol Min Typ Max Unit MH005A MH005B MH005C MH005BK VO, clamp VO, clamp VO, clamp VO1, clamp VO2, clamp VO1, clamp VO2, clamp -- -- -- -- -- -- -- -- -- -- -- -- -- -- 7.0 17 19 17 -17 19 -19 V V V V V V V MH005CL Lineage Power 5 MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 OUTPUT VOLTAGE, V O1 (V) Characteristic Curves INPUT CURRENT, I (A) 2.5 2.0 1.5 1.05 O, V set IO2 = 0.21 A V O, set 0.95 O, V set IO2 = 0.1 A IO2 = 0.01 A 1.0 0.01 0.04 0.08 0.12 0.16 0.20 OUTPUT CURRENT, IO1 (A) 0.5 8-871(C).a 0 0 2 4 6 8 10 12 14 16 Figure 3. MH005BK, CL Typical VO vs. IO Regulation with VI = 5 V and TA = 25 C INPUT VOLTAGE, VI(V) NORMALIZED OUTPUT VOLTAGE, V O /VO ,set 8-927(C) Figure 1. MH005-Series Typical Input Characteristics with IO = IO, max and TA = 25 C 1.05 1.04 1.03 V O /VO ,set,nom 1.02 V O = 1.02O ,Vnom 1.01 1.00 0.99 1.00 0.80 MH005A MH005B 0.60 MH005C 0.40 0.20 0.00 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 VO = V O ,nom 0.98 OUTPUT CURRENT, IO (A) 8-929(C) 0.97 V O = 0.98O ,Vnom 0.96 0.95 -10 0 10 20 30 40 50 60 70 80 90 100 CASE TEMPERATURE, T C (C) Figure 4. MH005A, B, C Typical Output Characteristics with VI = 5 V and TA = 25 C 8-928(C) Figure 2. MH005-Series Typical Output Voltage Variation over Operating Case Temperature 6 Lineage Power Data Sheet April 2008 MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W 12 OUTPUT VOLTAGE, V O (V) NORMALIZED OUTPUT VOLTAGE, V O /VO ,set Characteristic Curves (continued) 1.00 0.80 MH005A 0.60 MH005B MH005C 0.40 IO 2 = 0.05 A IO 2 = 0.10 A 8 IO 2 = 0.21 A 6 4 2 0 0.20 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 OUTPUT CURRENT, IO (A) 0.00 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 8-932(C) 4.0 OUTPUT CURRENT, IO (A) 8-930(C) Figure 7. MH005BK Typical Output Characteristics with VI = 12 V and TA = 25 C Figure 5. MH005A, B, C Typical Output Characteristics with VI = 12 V and TA = 25 C 10 IO 2 = 0.05 A 8 IO 2 = 0.10 A IO 2 = 0.21 A 6 OUTPUT VOLTAGE, V O1 (V) 15 12 OUTPUT VOLTAGE, V O1 (V) 10 12 IO2 = 0.17 A 9 6 3 0 0.0 4 2 IO2 = 0.08 A IO2 = 0.05 A 0.2 0.4 0.6 0.8 1.0 1.2 OUTPUT CURRENT, IO1 (A) 8-957(C) 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 OUTPUT CURRENT, IO1 (A) Figure 8. MH005CL Typical Output Characteristics with VI = 5 V and TA = 25 C 8-931(C) Figure 6. MH005BK Typical Output Characteristics with VI = 5 V and TA = 25 C Lineage Power 7 MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Characteristic Curves (continued) 75 EFFICIENCY, (%) OUTPUT VOLTAGE, V O1 (V) 15 12 IO2 = 0.17 A 9 IO2 = 0.08 A IO2 = 0.05 A 6 3 0 0.0 VI = 5 V V I = 12 V 65 60 55 0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.80 0.901.00 O ,max (A) NORMALIZED OUTPUT CURRENT, I O /I 0.2 0.4 0.6 0.8 1.0 1.2 8-958(C) 75 70 OUTPUT CURRENT, O MAX IO /I (A) VI = 5 V V I = 12 V 60 55 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 Figure 11. MH005B, C, BK, CL Typical Converter Efficiency as a Function of Output Current; TA = 25 C OUTPUT VOLTAGE, V O (V)(20 mV/div) Figure 9. MH005CL Typical Output Characteristics with VI = 12 V and TA = 25 C 65 8-934(C) 1.4 1.6 OUTPUT CURRENT, IO1 (A) EFFICIENCY, (%) 70 20 mV V O, 1 ms set 0.75 0.5 0.8 0.9 1.0 OUTPUT CURRENT, IO (A) 8-933(C) TIME, t (1 ms/div) 8-877(C) Figure 10. MH005A Typical Converter Efficiency as a Function of Output Current; TA = 25 C 8 Figure 12. Typical Output Voltage for a Step Load Change from 50% to 75% Lineage Power Data Sheet April 2008 MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Characteristic Curves (continued) Test Configurations TO OSCILLOSCOPE OUTPUT VOLTAGE, V O (V)(20 mV/div) 20 mV CURRENT PROBE LTEST V I(+) 500 H C S 220 F IMPEDANCE < 0.1 @ 20 C, 100 kHz BATTERY V O, OUTPUT CURRENT, O max (A) IO /I 1 ms set V I(-) 8-667(C).b Note: Input reflected-ripple current is measured with a simulated source impedance of 500 nH. Capacitor CS offsets possible battery impedance. Current is measured at the input of the module. 0.5 0.25 TIME, t (1 ms/div) Figure 15. Input Reflected-Ripple Test Setup 8-878(C) Figure 13. Typical Output Voltage for a Step Load Change from 50% to 25% COPPER STRIP V O (+) 1.0 F SCOPE NORMALIZED OUTPUT VOLTAGE, V O /VO ,set(V) 1 ms RESISTIVE LOAD V O (-) 8-513(C) 1 Note: Use a 0.1 F ceramic capacitor. Scope measurement should be made using a BNC socket. Position the load between 50 mm and 75 mm (2 in. and 3 in.) from the module. INPUT VOLTAGE, VI (V) (2 V/div) 0 Figure 16. Peak-to-Peak and RMS Output Noise Measurement Test Setup 5 CONTACT AND DISTRIBUTION LOSSES V I (+) 0 V O (+) IO II LOAD SUPPLY TIME, t (1 ms/div) 8-935(C) V I (-) V O (-) CONTACT RESISTANCE 8-204(C) Figure 14. Typical Output Voltage Start-Up when Input Voltage Applied; IO = 80% of IO, max Note: All measurements are taken at the module terminals. When socketing, place Kelvin connections at module terminals to avoid measurement errors due to socket contact resistance. [ V O (+) - V O (-) ] I O = ----------------------------------------------------- x 100 [ V I (+) - V I (-) ] II % Figure 17. Single-Output Voltage and Efficiency Measurement Test Setup Lineage Power 9 MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Test Configurations (continued) Safety Considerations CONTACT AND DISTRIBUTION LOSSES V I(+) V O1 LOAD IO II COM SUPPLY LOAD V I(-) V O2 CONTACT RESISTANCE 8-753(C) Note: All measurements are taken at the module terminals. When socketing, place Kelvin connections at module terminals to avoid measurement errors due to socket contact resistance. 2 j=1 [ V I (+) - V I (-) ] II For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. The input to these units is to be provided with a maximum 5 A normal-blow fuse in the ungrounded lead. [ V Oj (+) - V COM ] I Oj = ------------------------------------------------------------------------- x 100 For safety-agency approval of the system in which the power module is used, the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standard, i.e., UL 1950, CSA C22.2 No. 950-95, and VDE 0805 (EN60950, IEC950). % Figure 18. Dual-Output Voltage and Efficiency Measurement Test Setup Input Source Impedance The power module should be connected to a low acimpedance input source. Source impedances greater than 4 H can affect the stability of the power module. A 33 F electrolytic capacitor (ESR < 0.7 3/4 at 100 kHz) mounted close to the power module helps ensure stability of the unit. Feature Descriptions Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting for an unlimited duration. At the point of current-limit inception, the unit shifts from voltage control to current control. If the output voltage is pulled very low during a severe fault, the current-limit circuit can exhibit either foldback or tailout characteristics (output current decrease or increase). The unit operates normally once the output current is brought back into its specified range. Output Overvoltage Protection The output overvoltage clamp consists of control circuitry, which is independent of the primary regulation loop, that monitors the voltage on the output terminals. The control loop of the clamp has a higher voltage set point than the primary loop (see Feature Specifications table). This provides a redundant voltage-control that reduces the risk of output overvoltage. 10 Lineage Power MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Thermal Considerations The MH005-Series Power Modules are designed to operate in a variety of thermal environments. As with any electronic component, sufficient cooling must be provided to help ensure reliable operation. Heat-dissipating components inside the module are thermally coupled to the case to enable heat removal by conduction, convection, and radiation to the surrounding environment. The thermal data presented is based on measurements taken in a wind tunnel. The test setup shown in Figures 19 and 20 was used to collect data for Figures 21 and 22. The graphs in Figures 21 and 22 provide general guidelines for use. Actual performance can vary depending on the particular application environment. The maximum case temperature of 100 C must not be exceeded. 11.68 (0. CONNECTORS TO LOADS, POWER SUPPLIES, AND DATALOGGER, (6.35) 0.25 TALL 203.20 (8.00 AIRFLOW 63.50 (2.50) AIRFLOW MEASUREMENT 12.70 (0.50) T AMBIENT MEASUREMENT 12.70 (0.50) 203.20 (8.00) 9.65 (0.3 19.05 (0.75) 8-899(C) Note: Measurements are in millimeters and (inches). Figure 19. Thermal Test Setup 25.40 (1.00) MEASURE CASE TEMPERATURE HERE 8.89 (0.35) -12 V IN + MH005BK DC-DC Power Module IN:DC 5V, 1.37A OUT: DC 12V,0.21A OUT: DC -12V, 0.21A MADE IN USA COM 27.9 (1. MAX +12 V 50.8 (2.00) MAX 8-2240(C) Note: Pin locations are for reference only. Measurements are in millimeters and (inches). Figure 20. Case Temperature Measurement Location Lineage Power 11 MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Thermal Considerations (continued) Case-to-Ambient Thermal Impedance Basic Thermal Performance Figure 22 shows the case-to-ambient thermal impedance, ca (C/W) for the MH005 modules. This information is used to predict the case temperature for a given operating point and airflow by using the equation: The MH005-Series Power Modules are designed to operate at full load in natural convection at 70 C without the use of an external heat sink (see Figure 21). Higher ambient temperatures can be sustained by increasing the airflow. As stated, this data is based on a maximum case temperature of 100 C and measured in the test configuration of Figure 19. The location for the temperature measurement is shown in Figure 20. 1- T C = P O ------------ ca + T A where Tc is the case temperature (C), PO is the output power (W), is the efficiency for the desired voltage and load (see Characteristics Curves section), and TA is the ambient inlet temperature (C). CASE-TO-AMBIENT THERMAL RESISTANCE, CA (C/W) 6 OUTPUT POWER (W) 5 NATURAL CONVECTION 4 -1 (100 ft./min.) 0.5 ms -1 (200 ft./min.) 1.0 ms 3 2 17 16 15 14 13 12 11 10 9 8 7 6 5 0 0.25 0.5 0.75 1.0 1.25 1.5 1.75 2.0 (50) (100) (150) (200) (250) (300) (350) (400 -1 (ft./min.) AIR VELOCITY, ms 8-900(C).a 1 Figure 22. MH005A, B, C Case-to-Ambient Thermal Impedance 0 0 10 20 30 40 50 60 70 80 90 AMBIENT TEMPERATURE (C) 8-898(C) Figure 21. MH005A, B, C Derating Curve 12 Lineage Power MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Outline Diagrams Dimensions are in millimeters and (inches). Tolerances: x.x 0.5 mm (0.02 in.), x.xx 0.25 mm (0.010 in.). Single-Output Module Top View IN MH005A DC-DC Power Module + MADE IN USA IN:DC 5V, 1.41A OUT: DC 5V, 1A OUT 27.9 (1. MAX + 50.8 (2.00) MAX Side View 11.7 (0.4 MAX 0.51 (0.020) 0.79 (0.031) DIA ROUND PIN (TYP) 2.8 (0.1 Bottom View 5.08 (0.200) 12.70 (0.500 11.4 (0.45 7.62 (0.300) 15.2 (0.60) 20.32 (0.800) 8-317(C).d Lineage Power 13 MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Outline Diagrams (continued) Dimensions are in millimeters and (inches). Tolerances: x.x 0.5 mm (0.02 in.), x.xx 0.25 mm (0.010 in.). Dual-Output Module Top View -12 V IN + MH005BK DC-DC Power Module IN:DC 5V, 1.37A OUT: DC 12V,0.21A OUT: DC -12V,0.21A MADE IN USA COM 27.9 (1. MAX +12 V 50.8 (2.00) MAX Side View 11.7 (0.46) MAX 0.51 (0.020) 0.79 (0.031) DIA ROUND PIN (TYP) 2.8 (0.11) Bottom View 5.08 (0.200) 2.54 (0.100) 12.70 (0.500 11.4 (0.45 7.62 (0.300) 15.2 (0.60) 20.32 (0.800) 8-317(C).e 14 Lineage Power MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Recommended Hole Patterns Component-side footprint. Dimensions are in millimeters and (inches). Single-Output Module MODULE OUTLINE 7.62 (0.300) 11.4 (0.45) 5.08 (0.200) 12.70 (0.500) 15.2 (0.60) 20.32 (0.800) 8-317(C).d Dual-Output Module 7.62 (0.300) MODULE OUTLINE 11.4 (0.45) 5.08 (0.200) 12.70 (0.500) 2.54 (0.100) 15.2 (0.60) 20.32 (0.800) 8-317(C).e Lineage Power 15 MH005-Series Power Modules: 4.5 Vdc to 14 Vdc Input; 5 W Data Sheet April 2008 Ordering Information For assistance in ordering, please contact your Lineage Power Account Manager or Application Engineer. Table 4. Device Codes Input Voltage 5V 5V 5V 5V 5V Output Voltage 5V 12 V 15 V +12 V, -12 V +15 V, -15 V Output Power 5W 5W 5W 5W 5W Device Code MH005A MH005B MH005C MH005BK MH005CL Comcode 106604440 106617806 106617830 106604457 106617855 A sia-Pacific Head qu art ers T el: +65 6 41 6 4283 World W ide Headq u arters Lin eag e Po wer Co rp oratio n 30 00 Sk yline D riv e, Mes quite, T X 75149, U SA +1-800-526-7819 (Outs id e U .S.A .: +1- 97 2-2 84 -2626) www.line ag ep ower.co m e-m ail: tech sup port1@ lin ea gep ower.co m Eu ro pe, M id dle-East an d Afric a He ad qu arters T el: +49 8 9 6089 286 Ind ia Head qu arters T el: +91 8 0 28411633 Lineage Power reserves the right to make changes to the produc t(s) or information contained herein without notice. No liability is ass umed as a res ult of their use or applic ation. No rights under any patent acc ompany the sale of any s uc h pr oduct(s ) or information. (c) 2008 Lineage Power Corpor ation, (Mesquite, Texas ) All International Rights Res er ved. April 2008 DS98-223EPS (Replaces DS98-222EPS)