MPL115A2T1 - NXP SEMICONDUCTORS - Datasheet.Directory

MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Rev. 10 — 10 October 2017 Data sheet: technical data

1 General description

The MPL115A2 is an absolute pressure sensor with a digital I2C output targeting low

cost applications. A miniature 5 x 3 x 1.2 mm LGA package is ideally suited for the space

constrained requirements of portable electronic devices. Low current consumptions of

5 μA during Active mode and 1 μA during Shutdown (Sleep) mode are essential when

focusing on low-power applications. The wide operating temperature range spans from –

40 °C to +105 °C to fit demanding environmental conditions.

The MPL115A2 employs a MEMS pressure sensor with a conditioning IC to provide

accurate pressure measurements from 50 to 115 kPa. An integrated ADC converts

pressure and temperature sensor readings to digitized outputs via a I2C port. Factory

calibration data is stored internally in an on-board ROM. Utilizing the raw sensor output

and calibration data, the host microcontroller executes a compensation algorithm to

render Compensated Absolute Pressure with ±1 kPa accuracy.

The MPL115A2 pressure sensor’s small form factor, low power capability, precision, and

digital output optimize it for barometric measurement applications.

2 Features

•Digitized pressure and temperature information together with programmed calibration

coefficients for host micro use.

•Factory calibrated

•50 kPa to 115 kPa absolute pressure

•±1 kPa accuracy

•2.375 V to 5.5 V supply

•Integrated ADC

•I2C Interface (operates up to 400 kHz)

•7-bit I2C address = 60h

•Monotonic pressure and temperature data outputs

•Surface mount RoHS compliant package

3 Applications

•Barometry (portable and desktop)

•Altimeters

•Weather stations

•Hard-disk drives (HDD)

•Industrial equipment

•Health monitoring

•Air control systems

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

2 / 24

4 Ordering information

Table 1. Ordering information

PackageType number

Name Description Version

MPL115A2 TSON8 LGA 8 I/O, 3 X 5 X 1.25 PITCH, SENSOR 1.2MAX MM PKG SOT1769-1

4.1 Ordering options

Table 2. Ordering options

# of Ports Pressure TypeDevice Name Package Options

None Single Dual Gauge Differential Absolute

Digital

Interface

MPL115A2 Tray • • I2C

MPL115A2T1 Tape & Reel (1000) • • I2C

5 Block diagram

Figure 1. Block diagram of MPL115A2

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

3 / 24

6 Pinning information

6.1 Pinning

transparent top view

SDA

VDD

CAP

SHDN

GND

RST

SCL

MPL115A2

Figure 2. Pin configuration

6.2 Pin description

Table 3. Pin description

Pin Name Function

1 VDD Power Supply Connection: VDD range is 2.375 V to 5.5 V.

2 CAP 1 μF connected to ground.

3 GND Ground

4 SHDN

Shutdown: Connect to GND to disable the device. When in

shutdown, the part draws no more than 1 μA supply current and

all communications pins (RST, SCL, SDA) are high impedance.

Connect to VDD for normal operation.

5 RST Reset: Connect to ground to disable I2C communications.

6 NC No connection

7 SDA[1] Serial data I/O line

8 SCL[1] Serial clock input.

[1] Use 4.7 kΩ pullup resistors for I2C communication.

7 Handling and Board Mount Recommendations

The sensor die is sensitive to light exposure. Direct light exposure through the port hole

can lead to varied accuracy of pressure measurement. Avoid such exposure to the port

during normal operation.

7.1 Methods of Handling

Components can be picked from the carrier tape using either the vacuum assist or the

mechanical type pickup heads. A vacuum assist nozzle type is most common due to its

lower cost of maintenance and ease of operation. The recommended vacuum nozzle

configuration should be designed to make contact with the device directly on the metal

cover and avoid vacuum port location directly over the vent hole in the metal cover of the

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

4 / 24

device. Multiple vacuum ports within the nozzle may be required to effectively handle the

device and prevent shifting during movement to placement position.

Vacuum pressure required to adequately support the component should be

approximately 25 inches Hg (85 kPa). This level is typical of in-house vacuum supply.

Pickup nozzles are available in various sizes and configurations to suit a variety of

component geometries. To select the nozzle best suited for the specific application, it

is recommended that the customer consult their pick and place equipment supplier to

determine the correct nozzle. In some cases it may be necessary to fabricate a special

nozzle depending on the equipment and speed of operation.

Tweezers or other mechanical forms of handling that have a sharp point are not

recommended since they can inadvertently be inserted into the vent hole of the device.

This can lead to a puncture of the MEMS element that will render the device inoperable.

7.2 Board Mount Recommendations

Components can be mounted using solder paste stencil, screen printed or dispensed

onto the PCB pads prior to placement of the component. The volume of solder paste

applied to the PCB is normally sufficient to secure the component during transport to the

subsequent reflow soldering process. Use of adhesives to secure the component is not

recommended, but where necessary can be applied to the underside of the device.

Solder pastes are available in variety of metal compositions, particle size and flux types.

The solder paste consists of metals and flux required for a reliable connection between

the component lead and the PCB pad. Flux aids the removal of oxides that may be

present on PCB pads and prevents further oxidation from occurring during the solder

process.

The use of a No-Clean (NC) flux is recommended for exposed cavity components.

Using pressure spray, wire brush, or other methods of cleaning is not recommended

since it can puncture the MEMS device and render it unusable. If cleaning of the pcb

is performed, Water Soluble (WS) flux can be used. However, it is recommended the

component cavity is protected by adhesive Kapton tape, vinyl cap or other means

prior to the cleaning process. This covering will prevent damage to the MEMS device,

contamination, and foreign materials from being introduced into device cavity as result of

cleaning processes.

Ultrasonic cleaning is not recommended as the frequencies can damage wire bond

interconnections and the MEMS device.

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

5 / 24

8 Functional description

Readin g

coefficient data

Data conversion

Initial

powerup

Compensated

pressure readin g

Shutdown

Figure 3. Sequence flow chart

The MPL115A interfaces to a host (or system) microcontroller in the user’s application.

All communications are via I2C. A typical usage sequence is as follows:

Initial power-up

All circuit elements are active. I2C port pins are high impedance and associated registers

are cleared. The device then enters standby mode.

Reading coefficient data

The user then typically accesses the part and reads the coefficient data. The main

circuits within the slave device are disabled during read activity. The coefficients are

usually stored in the host microcontoller local memory but can be re-read at any time.

It is not necessary to read the values stored in the host microcontroller multiple times

because the coefficients within a device are constant and do not change. However,

note that the coefficients will be different from device to device, and cannot be used for

another part.

Data conversion

This is the first step that is performed each time a new pressure reading is required which

is initiated by the host sending the CONVERT command. The main system circuits are

activated (wake) in response to the command and after the conversion completes, the

result is placed into the Pressure and Temperature ADC output registers.

The conversion completes within the maximum conversion time, tc (see row 7, in

Table 10). The device then enters standby mode.

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

6 / 24

Compensated pressure reading

After the conversion has been given sufficient time to complete, the host microcontroller

reads the result from the ADC output registers and calculates the Compensated

Pressure, a barometric/atmospheric pressure value which is compensated for changes

in temperature and pressure sensor linearity. This is done using the coefficient data

from the MPL115A and the raw sampled pressure and temperature ADC output values,

in a compensation equation (detailed later). Note that this is an absolute pressure

measurement with a vacuum as a reference.

From this step the host controller may either wait and then return to the Data Conversion

step to obtain the next pressure reading or it may go to the Shutdown step.

Shutdown

For longer periods of inactivity the user may assert the SHDN input by driving this pin

low to reduce system power consumption. This removes power from all internal circuits,

including any registers. In the shutdown state, the Pressure and Temperature registers

will be reset, losing any previous ADC output values.

This step is exited by taking the SHDN pin high. Wait for the maximum wakeup time,

tw (see row 8, in Table 10), after which another pressure reading can be taken by

transitioning to the data Conversion step.

Table 4. Device memory map

Address Name Description

00h Padc_MSB 10-bit Pressure ADC output value MSB

01h Padc_LSB 10-bit Pressure ADC output value LSB

02h Tadc_MSB 10-bit Temperature ADC output value MSB

03h Tacd_LSB 10-bit Temperature ADC output value LSB

04h a0_MSB a0 coefficient MSB

05h a0_LSB a0 coefficient LSB

06h b1_MSB b1 coefficient MSB

07h b1_LSB b1 coefficient LSB

08h b2_MSB b2 coefficient MSB

09h b2_LSB b2 coefficient LSB

0Ah c12_MSB c12 coefficient MSB

0Bh c12_LSB c12 coefficient LSB

0Ch reserved[1] —

0Dh reserved[1] —

0Eh reserved[1] —

0Fh reserved[1] —

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

7 / 24

Address Name Description

10h reserved —

11h reserved —

12h CONVERT Start Pressure and Temperature Conversion

[1] This register is set to 00h. It is reserved, and was previously utilized as Coefficient values, c11 and c22, which were

always 00h.

For values with less than 16 bits, the lower LSBs are zero. For example, c12 is 14 bits

and is stored into 2 bytes as follows:

c12 MS byte = c12[13:6] = [c12b13 , c12b12 , c12b11 , c12b10 , c12b9 , c12b8 , c12b7 , c12b6]

c12 LS byte = c12[5:0] & "00" = [c12b5 , c12b4 , c12b3 , c12b2 , c12b1 , c12b0 , 0 , 0]

8.1 Pressure, temperature and coefficient bit-width specifications

The table below specifies the initial coefficient bit-width specifications for the

compensation algorithm and the specifications for Pressure and Temperature ADC

values.

Table 5. Pressure, temperature and compensation coefficient specifications

a0 b1 b2 c12 Padc Tadc

Total Bits 16 16 16 14 10 10

Sign Bits 111100

Integer Bits 12 2 1 0 10 10

Fractional Bits 3 13 14 13 0 0

dec pt zero pad 000900

Example Binary Format Definitions:

a0 Signed, Integer Bits = 12, Fractional Bits = 3 : Coeff a0 = S I11 I10 I9 I8 I7 I6 I5 I4 I3 I2 I1 I0 . F2 F1 F0

b1 Signed, Integer Bits = 2, Fractional Bits = 13 : Coeff b1 = S I1 I0 . F12 F11 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 F0

b2 Signed, Integer Bits = 1, Fractional Bits = 14 : Coeff b2 = S I0 . F13 F12 F11 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 F0

c12 Signed, Integer Bits = 0, Fractional Bits = 13, dec pt zero pad = 9 : Coeff c12 = S 0 . 000 000 000 F12 F11 F10 F9 F8 F7 F6 F5 F4 F3 F2 F1 F0

Padc Unsigned, Integer Bits = 10 : Padc U = I9 I8 I7 I6 I5 I4 I3 I2 I1 I0

Tadc Unsigned, Integer Bits =10 : Tadc U = I9 I8 I7 I6 I5 I4 I3 I2 I1 I0

Note: Negative coefficients are coded in 2’s complement notation.

8.2 Compensation

The 10-bit compensated pressure output, Pcomp, is calculated as follows:

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

8 / 24

(1)

Where:

Padc is the 10-bit pressure ADC output of the MPL115A

Tadc is the 10-bit temperature ADC output of the MPL115A

a0 is the pressure offset coefficient

b1 is the pressure sensitivity coefficient

b2 is the temperature coefficient of offset (TCO)

c12 is the temperature coefficient of sensitivity (TCS)

Pcomp will produce a value of 0 with an input pressure of 50 kPa and will produce a full-

scale value of 1023 with an input pressure of 115 kPa.

(2)

8.3 Evaluation sequence, arithmetic circuits

The following is an example of the calculation for Pcomp, the compensated pressure

output. Input values are in bold.

c12x2 = c12 * Tadc

a1 = b1 + c12x2

a1x1 = a1 * Padc

y1 = a0 + a1x1

a2x2 = b2 * Tadc

Pcomp = y1 + a2x2

This can be calculated as a succession of Multiply Accumulates (MACs) operations of the

form y = a + b * x:

The polynomial can be evaluated (Equation 1) as a sequence of 3 MACs:

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

9 / 24

c12

Tadc

Padc

PComp

Please refer to NXP application note AN3785 for more detailed notes on implementation.

8.4 I2C device read/write operations

All device read/write operations are memory mapped. Device actions, for example, Start

Conversions, are controlled by writing to the appropriate memory address location.

•For I2C the 7-bit device address (from Table 2) has a read/write toggle bit, where the

least significant bit is ‘1’ for read operations or ‘0’ for write operations. The Device

Address is C0h for a Write and the Device Address is C1h for a Read.

•The most significant bit in the Command tables below is not used and is don't care (X).

In examples given it’s set to ‘0’.

Refer to Sensor I2C Setup and FAQ Application Note AN4481 for more information on

I2C communication between the sensor and host controller.

Table 6. I2C write commands

Legend: X - don't care

Command Binary HEX[1]

Devices Address + Write bit 1100 0000 C0h

Start Conversions X001 0010 12h

[1] The command byte needs to be paired with a 00h as part of the I2C exchange to complete the passing of Start

Conversions.

The actions taken by the part in response to each command are as follows:

Table 7. I2C write command description

Command Action Taken

Start Conversions Wake main circuits. Start clock. Allow supply stabilization time. Select

pressure sensor input. Apply positive sensor excitation and perform A

to D conversion. Select temperature input. Perform A to D conversion.

Load the Pressure and Temperature registers with the result. Shut down

main circuits and clock.

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

10 / 24

Table 8. I2C read command description

Legend: X - don't care

Command Binary HEX

Device Address + Read bit 1100 0001 C1h

Read Pressure MSB X000 0000 00h

Read Pressure LSB X000 0001 01h

Read Temperature MSB X000 0010 02h

Read Temperature LSB X000 0011 03h

Read Coefficient data byte 1 X000 0100 04h

These are MPL115A2 I2C commands to read coefficients, execute pressure and

temperature conversions, and to read pressure and temperature data. The sequence of

the commands for the interaction is given as an example to operate the MPL115A2.

Utilizing this gathered data, an example of the calculating the compensated pressure

reading is given in floating point notation.

I2C commands (simplified for communication)

Device Address + write bit "To Write" = C0h

Device Address + read bit "To Read" = C1h

Command to Write "Convert Pressure and Temperature" = 12h

Command to Read "Pressure ADC High byte" = 00h

Command to Read "Pressure ADC Low byte" = 01h

Command to Read "Temperature ADC High byte" = 02h

Command to Read "Temperature ADC Low byte" = 03h

Command to Read "Coefficient data byte 1 High byte" = 04h

Read coefficients

[C0h], [04h], [C1h], [3Eh], [CEh], [B3h], [F9h], [C5h], [17h], [33h], [C8h]

Figure 4. I2C read coefficient datagram

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

11 / 24

a0 coefficient MSB = 3Eh

a0 coefficient LSB = CEh a0 coefficient = 3ECEh = 2009.75

b1 coefficient MSB = B3h

b1 coefficient LSB = F9h b1 coefficient = B3F9h = -2.37585

b2 coefficient MSB = C5h

b2 coefficient LSB = 17h b2 coefficient = C517h = -0.92047

c12 coefficient MSB = 33h

c12 coefficient LSB = C8h c12 coefficient = 33C8h = 0.000790

Command to I2C start conversion, 12h

Figure 5. I2C Start conversion datagram

Figure 6. I2C read results datagram

Pressure MSB = 66h

Pressure LSB = 80h Pressure = 6680h = 0110 0110 1100

0000

= 410 ADC counts

Temperature MSB = 7Eh

Temperature LSB = C0h Temperature = 7EC0h = 0111 1110 1100

0000

= 507 ADC counts

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

12 / 24

8.5 Example of pressure compensated calculation in floating-point

notation

a0 coefficient = 2009.75

b1 coefficient = -2.37585

b2 coefficient = -0.92047

c12 coefficient = 0.000790

Pressure = 410 ADC counts

Temperature = 507 ADC counts

Pressure compensation

Using the evaluation sequence

The evaluation sequence is located in Section 8.3.

c12x2 = c12 * Tadc = 0.000790 * 507 = 0.40053

a1 = b1 + c12x2 = -2.37585 + 0.40053 = -1.97532

a1x1 = a1 * Padc = -1.97532 * 410 = -809.8812

y1 = a0 + a1x1 = 2009.75 + (-809.8812) = 1199.8688

a2x2 = b2 * Tadc = -0.92047 * 507 = -466.67829

PComp = y1 + a2x2 = 1199.8688 + (-466.67829) = 733.19051

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

13 / 24

9 Maximum ratings

Table 9. Maximum ratings

Voltage (with respect to GND unless otherwise noted)

Symbol Value Units

VDD –0.3 to +5.5 V

SHDN, RST, SDA, SCL –0.3 to VDD + 0.3 V

Operating Temperature Range –40 to +105 °C

Storage Temperature Range –40 to +125 °C

Overpressure 1000 kPa

10 Mechanical and electrical characteristics

Table 10. Mechanical and electrical characteristics

VDD = 2.375 V to 5.5 V, TA = –40 °C to +105 °C, unless otherwise noted. Typical values are at VDD = 3.3 V, TA = +25 °C.

Ref Parameters Symbol Conditions Min Typ Max Units

1 Operating Supply Voltage VDD 2.375 3.3 5.5 V

Shutdown (SHDN = GND) — — 1 μA

Standby — 3.5 10 μA

2 Supply Current IDD

Average – at one measurement per

second

— 5 6 μA

Pressure Sensor

3 Range 50 — 115 kPa

4 Resolution — 0.15 — kPa

5 Accuracy –20 ºC to 85 ºC — — ±1 kPa

Typical operating circuit at DC 0.1 — kPa/V6 Power Supply Rejection

100 mV p-p 217 Hz square wave plus

100 mV pseudo random noise with 10

MHz bandwidth

0.1 — kPa

7 Conversion Time

(Start Pressure and

Temperature Conversion)

tc Time between start convert command

and data available in the Pressure and

Temperature registers

— 1.6 3 ms

8 Wakeup Time tw Time between leaving Shutdown

mode (SHDN goes high) and

communicating with the device to

issue a command or read data.

— 3 5 ms

I2C I/O Stages: SCL, SDA

9 SCL Clock Frequency fSCL — — 400 kHz

10 Low Level Input Voltage VIL — — 0.3VDD V

11 High Level Input Voltage VIH 0.7VDD — — V

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

14 / 24

Ref Parameters Symbol Conditions Min Typ Max Units

I2C Outputs: SDA

12 Data Setup Time tSU Setup time from command receipt to

ready to transmit

0 — 0.4 s

I2C Addressing

MPL115A2 uses 7-bit addressing, does not acknowledge the general call address 0000000. Slave address has been set to

60h or 1100000.

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

15 / 24

11 Package outline

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

16 / 24

Figure 7. Package outline SOT1769-1 (TSON8)

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

17 / 24

12 Packing information

Figure 8. LGA (3 x 5) embossed carrier tape dimensions

Figure 9. Device orientation in chip carrier

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

18 / 24

13 Soldering

1. Use SAC solder alloy, i.e., Sn-Ag-Cu, with a melting point of about 217 °C. It is

recommended to use SAC305, i.e., Sn-3.0 wt.% Ag-0.5 wt.% Cu.

2. Reflow

•Ramp up rate: 2 to 3 °C/s.

•Preheat flat (soak): 110 to 130 s.

•Reflow peak temperature: 250 °C to 260 °C (depends on exact SAC alloy

composition).

•Time above 217°C: 40 to 90s (depends on board type, thermal mass of the board/

quantities in the reflow).

•Ramp down: 5 to 6 °C/s.

•Using an inert reflow environment (with O2 level about 5 to 15 ppm).

Note: The stress level and signal offset of the device also depends on the board type,

board core material, board thickness and metal finishing of the board.

Please refer to NXP application note AN3150, Soldering Recommendations for Pressure

Sensor Devices for any additional information.

14 Soldering/landing pad information

The LGA package is compliant with the RoHS standard. It is recommended to use a no-

clean solder paste to reduce cleaning exposure to high pressure and chemical agents

that can damage or reduce life span of the Pressure sensing element.

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

19 / 24

Figure 10. Recommended PCB landing pattern

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

20 / 24

15 Revision history

Table 11. Revision history

Document ID Release date Data sheet status Change notice Supersedes

MPL115A2 v.10 20171010 Technical data — MPL115A2 v.9

Modifications: •The format of this data sheet has been redesigned to comply with the new identity guidelines

of NXP Semiconductors.

•Legal texts have been adapted to the new company name where appropriate.

•Removed the first paragraph of Section 7.

•Added Section 7.1 and Section 7.2 in Section 7 "Handling and Board Mount

Recommendations"

•Updated Figure 7. No technical changes.

MPL115A2 v.9 10/2012 Technical data — MPL115A2 v.8

MPL115A2 v.8 06/2012 Technical data — —

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

21 / 24

16 Legal information

16.1 Data sheet status

Document status[1][2] Product status[3] Definition

[short] Data sheet: product preview Development This document contains certain information on a product under development.

NXP reserves the right to change or discontinue this product without notice.

[short] Data sheet: advance information Qualification This document contains information on a new product. Specifications and

information herein are subject to change without notice.

[short] Data sheet: technical data Production This document contains the product specification. NXP Semiconductors

reserves the right to change the detail specifications as may be required to

permit improvements in the design of its products.

[1] Please consult the most recently issued document before initiating or completing a design.

[2] The term 'short data sheet' is explained in section "Definitions".

[3] The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple

devices. The latest product status information is available on the Internet at URL http://www.nxp.com.

16.2 Definitions

Draft — The document is a draft version only. The content is still under

internal review and subject to formal approval, which may result in

modifications or additions. NXP Semiconductors does not give any

representations or warranties as to the accuracy or completeness of

information included herein and shall have no liability for the consequences

of use of such information.

Short data sheet — A short data sheet is an extract from a full data sheet

with the same product type number(s) and title. A short data sheet is

intended for quick reference only and should not be relied upon to contain

detailed and full information. For detailed and full information see the

relevant full data sheet, which is available on request via the local NXP

Semiconductors sales office. In case of any inconsistency or conflict with the

short data sheet, the full data sheet shall prevail.

Product specification — The information and data provided in a

technical data data sheet shall define the specification of the product as

agreed between NXP Semiconductors and its customer, unless NXP

Semiconductors and customer have explicitly agreed otherwise in writing.

In no event however, shall an agreement be valid in which the NXP

Semiconductors product is deemed to offer functions and qualities beyond

those described in the technical data data sheet.

16.3 Disclaimers

Limited warranty and liability — Information in this document is believed

to be accurate and reliable. However, NXP Semiconductors does not

give any representations or warranties, expressed or implied, as to the

accuracy or completeness of such information and shall have no liability

for the consequences of use of such information. NXP Semiconductors

takes no responsibility for the content in this document if provided by an

information source outside of NXP Semiconductors. In no event shall NXP

Semiconductors be liable for any indirect, incidental, punitive, special or

consequential damages (including - without limitation - lost profits, lost

savings, business interruption, costs related to the removal or replacement

of any products or rework charges) whether or not such damages are based

on tort (including negligence), warranty, breach of contract or any other

legal theory. Notwithstanding any damages that customer might incur for

any reason whatsoever, NXP Semiconductors’ aggregate and cumulative

liability towards customer for the products described herein shall be limited

in accordance with the Terms and conditions of commercial sale of NXP

Semiconductors.

Right to make changes — NXP Semiconductors reserves the right to

make changes to information published in this document, including without

limitation specifications and product descriptions, at any time and without

notice. This document supersedes and replaces all information supplied prior

to the publication hereof.

Suitability for use — NXP Semiconductors products are not designed,

authorized or warranted to be suitable for use in life support, life-critical or

safety-critical systems or equipment, nor in applications where failure or

malfunction of an NXP Semiconductors product can reasonably be expected

to result in personal injury, death or severe property or environmental

damage. NXP Semiconductors and its suppliers accept no liability for

inclusion and/or use of NXP Semiconductors products in such equipment or

applications and therefore such inclusion and/or use is at the customer’s own

risk.

Applications — Applications that are described herein for any of these

products are for illustrative purposes only. NXP Semiconductors makes

no representation or warranty that such applications will be suitable

for the specified use without further testing or modification. Customers

are responsible for the design and operation of their applications and

products using NXP Semiconductors products, and NXP Semiconductors

accepts no liability for any assistance with applications or customer product

design. It is customer’s sole responsibility to determine whether the NXP

Semiconductors product is suitable and fit for the customer’s applications

and products planned, as well as for the planned application and use of

customer’s third party customer(s). Customers should provide appropriate

design and operating safeguards to minimize the risks associated with

their applications and products. NXP Semiconductors does not accept any

liability related to any default, damage, costs or problem which is based

on any weakness or default in the customer’s applications or products, or

the application or use by customer’s third party customer(s). Customer is

responsible for doing all necessary testing for the customer’s applications

and products using NXP Semiconductors products in order to avoid a

default of the applications and the products or of the application or use by

customer’s third party customer(s). NXP does not accept any liability in this

respect.

Limiting values — Stress above one or more limiting values (as defined in

the Absolute Maximum Ratings System of IEC 60134) will cause permanent

damage to the device. Limiting values are stress ratings only and (proper)

operation of the device at these or any other conditions above those

given in the Recommended operating conditions section (if present) or the

Characteristics sections of this document is not warranted. Constant or

repeated exposure to limiting values will permanently and irreversibly affect

the quality and reliability of the device.

Terms and conditions of commercial sale — NXP Semiconductors

products are sold subject to the general terms and conditions of commercial

sale, as published at http://www.nxp.com/profile/terms, unless otherwise

agreed in a valid written individual agreement. In case an individual

agreement is concluded only the terms and conditions of the respective

agreement shall apply. NXP Semiconductors hereby expressly objects to

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

22 / 24

applying the customer’s general terms and conditions with regard to the

purchase of NXP Semiconductors products by customer.

No offer to sell or license — Nothing in this document may be interpreted

or construed as an offer to sell products that is open for acceptance or

the grant, conveyance or implication of any license under any copyrights,

patents or other industrial or intellectual property rights.

Export control — This document as well as the item(s) described herein

may be subject to export control regulations. Export might require a prior

authorization from competent authorities.

Non-automotive qualified products — Unless this data sheet expressly

states that this specific NXP Semiconductors product is automotive qualified,

the product is not suitable for automotive use. It is neither qualified nor

tested in accordance with automotive testing or application requirements.

NXP Semiconductors accepts no liability for inclusion and/or use of non-

automotive qualified products in automotive equipment or applications. In

the event that customer uses the product for design-in and use in automotive

applications to automotive specifications and standards, customer (a) shall

use the product without NXP Semiconductors’ warranty of the product for

such automotive applications, use and specifications, and (b) whenever

customer uses the product for automotive applications beyond NXP

Semiconductors’ specifications such use shall be solely at customer’s own

risk, and (c) customer fully indemnifies NXP Semiconductors for any liability,

damages or failed product claims resulting from customer design and use

of the product for automotive applications beyond NXP Semiconductors’

standard warranty and NXP Semiconductors’ product specifications.

Translations — A non-English (translated) version of a document is for

reference only. The English version shall prevail in case of any discrepancy

between the translated and English versions.

16.4 Trademarks

Notice: All referenced brands, product names, service names and

trademarks are the property of their respective owners.

NXP — is a trademark of NXP B.V.

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Data sheet: technical data Rev. 10 — 10 October 2017

23 / 24

Tables

Tab. 1. Ordering information ..........................................2

Tab. 2. Ordering options ................................................2

Tab. 3. Pin description ...................................................3

Tab. 4. Device memory map ......................................... 6

Tab. 5. Pressure, temperature and compensation

coefficient specifications ....................................7

Tab. 6. I2C write commands ......................................... 9

Tab. 7. I2C write command description .........................9

Tab. 8. I2C read command description ....................... 10

Tab. 9. Maximum ratings .............................................13

Tab. 10. Mechanical and electrical characteristics ........ 13

Tab. 11. Revision history ...............................................20

Figures

Fig. 1. Block diagram of MPL115A2 .............................2

Fig. 2. Pin configuration ............................................... 3

Fig. 3. Sequence flow chart ......................................... 5

Fig. 4. I2C read coefficient datagram ......................... 10

Fig. 5. I2C Start conversion datagram ....................... 11

Fig. 6. I2C read results datagram .............................. 11

Fig. 7. Package outline SOT1769-1 (TSON8) ............ 15

Fig. 8. LGA (3 x 5) embossed carrier tape

dimensions ...................................................... 17

Fig. 9. Device orientation in chip carrier .....................17

Fig. 10. Recommended PCB landing pattern ............... 19

NXP Semiconductors MPL115A2

Miniature I2C digital barometer, 50 to 115 kPa

Please be aware that important notices concerning this document and the product(s)

described herein, have been included in section 'Legal information'.

For more information, please visit: http://www.nxp.com

For sales office addresses, please send an email to: salesaddresses@nxp.com

Date of release: 10 October 2017

Document identifier: MPL115A2

Contents

1 General description ............................................ 1

2 Features ............................................................... 1

3 Applications .........................................................1

4 Ordering information .......................................... 2

4.1 Ordering options ................................................ 2

5 Block diagram ..................................................... 2

6 Pinning information ............................................ 3

6.1 Pinning ...............................................................3

6.2 Pin description ................................................... 3

7 Handling and Board Mount

Recommendations .............................................. 3

7.1 Methods of Handling ......................................... 3

7.2 Board Mount Recommendations ....................... 4

8 Functional description ........................................5

8.1 Pressure, temperature and coefficient bit-

width specifications ............................................7

8.2 Compensation ....................................................7

8.3 Evaluation sequence, arithmetic circuits ............8

8.4 I2C device read/write operations ....................... 9

8.5 Example of pressure compensated

calculation in floating-point notation .................12

9 Maximum ratings ...............................................13

10 Mechanical and electrical characteristics .......13

11 Package outline .................................................15

12 Packing information ..........................................17

13 Soldering ............................................................18

14 Soldering/landing pad information ..................18

15 Revision history ................................................ 20

16 Legal information ..............................................21