Si827x Data Sheet
4 Amp ISOdriver with High Transient (dV/dt) Immunity
The Si827x isolators are ideal for driving power switches used in a wide variety of power
supply, inverter, and motor control applications. The Si827x isolated gate drivers utilize
Silicon Laboratories' proprietary silicon isolation technology, supporting up to 2.5
kVRMS withstand voltage per UL1577 and VDE0884. This technology enables industry
leading common-mode transient immunity (CMTI), tight timing specifications, reduced
variation with temperature and age, better part-to-part matching, and extremely high reli-
ability. It also offers unique features such as separate pull-up/down outputs, driver shut-
down on UVLO fault, and precise dead time programmability. The Si827x series offers
longer service life and dramatically higher reliability compared to opto-coupled gate driv-
ers.
The Si827x drivers utilize Silicon Labs' proprietary silicon isolation technology, which
provides up to 2.5 kVRMS withstand voltage per UL1577 and fast 60 ns propagation
times. Driver outputs can be grounded to the same or separate grounds or connected to
a positive or negative voltage. The TTL level compatible inputs with >400 mV hysteresis
are available in individual control input (Si8271/2/3/5) or PWM input (Si8274) configura-
tions. High integration, low propagation delay, small installed size, flexibility, and cost-
effectiveness make the Si827x family ideal for a wide range of isolated MOSFET/IGBT
and SiC or GaN FET gate drive applications.
Automotive Grade is available for certain part numbers. These products are built using
automotive-specific flows at all steps in the manufacturing process to ensure the robust-
ness and low defectivity required for automotive applications.
KEY FEATURES
• Single, dual, or high-side/low-side drivers
• Single PWM or dual digital inputs
•High dV/dt immunity:
• 200 kV/µs CMTI
• 400 kV/µs Latch-up
• Separate pull-up/down outputs for slew
rate control
• Wide supply range:
• Input supply: 2.5–5.5 V
• Driver supply: 4.2–30 V
• Very low jitter of 200 ps p-p
• 60 ns propagation delay (max)
• Dedicated enable pin
• Silicon Labs’ high performance isolation
technology:
• Industry leading noise immunity
• High speed, low latency and skew
• Best reliability available
• Compact packages:
• 8-pin SOIC
• 16-pin SOIC
• QFN-14 (pin to pin compatible with
LGA-14 packages)
• Wide temperature range:
• –40 to 125 °C
• AEC-Q100 Qualified
• Automotive-grade OPNs available
• AIAG compliant PPAP documentation
support
• IMDS and CAMDS listing support
Industrial Applications
• Switch-mode Power Supplies
•Solar Power Inverters
• Motor control and drives
• Uninterruptible Power Supplies
• High-Power Class D Amplifiers
Safety Regulatory Approvals
• UL 1577 recognized
• Up to 2500 Vrms for 1 minute
• CSA component notice 5A approval
• IEC 60950-1 (reinforced insulation)
• VDE certification conformity
• VDE 0884 Part 10
• CQC certification approval
• GB4943.1
Automotive Applications
•On-board chargers
•Battery management systems
• Charging stations
• Traction inverters
• Hybrid Electric Vehicles
• Battery Electric Vehicles
silabs.com | Building a more connected world. Rev. 1.01
1. Ordering Guide
Table 1.1. Si827x Ordering Guide
Ordering
Part Number
Inputs Driver
Configuration
Output
UVLO
Integrated
Deglitcher
Dead Time
Adjustable
Range
Low
Jitter
Package Isolation
Rating
Products Available Now
Si8271AB-IS VI Single 5 N N/A Y SOIC-8 NB 2.5 kVrms
Si8271BB-IS VI Single 8 N N/A Y SOIC-8 NB 2.5 kVrms
Si8271DB-IS VI Single 12 N N/A Y SOIC-8 NB 2.5 kVrms
Si8271GB-IS VI Single 3 N N/A Y SOIC-8 NB 2.5 kVrms
Si8273AB-IS1 VIA/VIB HS/LS 5 N N/A Y SOIC-16 NB 2.5 kVrms
Si8273ABD-IS1 VIA/VIB HS/LS 5 Y N/A N SOIC-16 NB 2.5 kVrms
Si8273AB-IM1 VIA/VIB HS/LS 5 N N/A Y QFN-14 2.5 kVrms
Si8273ABD-IM1 VIA/VIB HS/LS 5 Y N/A N QFN-14 2.5 kVrms
Si8273DB-IS1 VIA/VIB HS/LS 12 N N/A Y SOIC-16 NB 2.5 kVrms
Si8273DBD-IS1 VIA/VIB HS/LS 12 Y N/A N SOIC-16 NB 2.5 kVrms
Si8273GB-IS1 VIA/VIB HS/LS 3 N N/A Y SOIC-16 NB 2.5 kVrms
Si8273GBD-IS1 VIA/VIB HS/LS 3 Y N/A N SOIC-16 NB 2.5 kVrms
Si8273BB-IS1 VIA/VIB HS/LS 8 N N/A Y SOIC-16 NB 2.5 kVrms
Si8273BBD-IS1 VIA/VIB HS/LS 8 Y N/A N SOIC-16 NB 2.5 kVrms
Si8274AB1-IS1 PWM HS/LS 5 N 10-200 Y SOIC-16 NB 2.5 kVrms
Si8274AB4D-IS1 PWM HS/LS 5 Y 20-700 N SOIC-16 NB 2.5 kVrms
Si8274AB1-IM1 PWM HS/LS 5 N 10-200 Y QFN-14 2.5 kVrms
Si8274AB4D-IM1 PWM HS/LS 5 Y 20-700 N QFN-14 2.5 kVrms
Si8274BB1-IS1 PWM HS/LS 8 N 10-200 Y SOIC-16 NB 2.5 kVrms
Si8274DB1-IS1 PWM HS/LS 12 N 10-200 Y SOIC-16 NB 2.5 kVrms
Si8274GB1-IS1 PWM HS/LS 3 N 10-200 Y SOIC-16 NB 2.5 kVrms
Si8274GB4D-IS1 PWM HS/LS 3 Y 20-700 N SOIC-16 NB 2.5 kVrms
Si8274GB1-IM1 PWM HS/LS 3 N 10-200 Y QFN-14 2.5 kVrms
Si8274GB4D-IM1 PWM HS/LS 3 Y 20-700 N QFN-14 2.5 kVrms
Si8275GB-IS1 VIA/VIB Dual 3 N N/A Y SOIC-16 NB 2.5 kVrms
Si8275GBD-IS1 VIA/VIB Dual 3 Y N/A N SOIC-16 NB 2.5 kVrms
Si8275AB-IM1 VIA/VIB Dual 5 N N/A Y QFN-14 2.5 kVrms
Si8275ABD-IM1 VIA/VIB Dual 5 Y N/A N QFN-14 2.5 kVrms
Contact Silicon Labs Sales for These Options
Si8271ABD-IS VI Single 5 Y N/A N SOIC-8 NB 2.5 kVrms
Si8271BBD-IS VI Single 8 Y N/A N SOIC-8 NB 2.5 kVrms
Si827x Data Sheet
Ordering Guide
silabs.com | Building a more connected world. Rev. 1.01 | 2
Ordering
Part Number
Inputs Driver
Configuration
Output
UVLO
Integrated
Deglitcher
Dead Time
Adjustable
Range
Low
Jitter
Package Isolation
Rating
Si8271DBD-IS VI Single 12 Y N/A N SOIC-8 NB 2.5 kVrms
Si8271GBD-IS VI Single 3 Y N/A N SOIC-8 NB 2.5 kVrms
Si8273BB-IS1 VIA/VIB HS/LS 8 N N/A Y SOIC-16 NB 2.5 kVrms
Si8273BBD-IS1 VIA/VIB HS/LS 8 Y N/A N SOIC-16 NB 2.5 kVrms
Si8274BB4D-IS1 PWM HS/LS 8 Y 20-700 N SOIC-16 NB 2.5 kVrms
Si8274DB4D-IS1 PWM HS/LS 12 Y 20-700 N SOIC-16 NB 2.5 kVrms
Si8275AB-IS1 VIA/VIB Dual 5 N N/A Y SOIC-16 NB 2.5 kVrms
Si8275ABD-IS1 VIA/VIB Dual 5 Y N/A N SOIC-16 NB 2.5 kVrms
Si8275BB-IS1 VIA/VIB Dual 8 N N/A Y SOIC-16 NB 2.5 kVrms
Si8275BBD-IS1 VIA/VIB Dual 8 Y N/A N SOIC-16 NB 2.5 kVrms
Si8275DB-IS1 VIA/VIB Dual 12 N N/A Y SOIC-16 NB 2.5 kVrms
Si8275DBD-IS1 VIA/VIB Dual 12 Y N/A N SOIC-16 NB 2.5 kVrms
Si8275BB-IM1 VIA/VIB Dual 8 N N/A Y QFN-14 2.5 kVrms
Si8275BBD-IM1 VIA/VIB Dual 8 Y N/A N QFN-14 2.5 kVrms
Si8275DB-IM1 VIA/VIB Dual 12 N N/A Y QFN-14 2.5 kVrms
Si8275DBD-IM1 VIA/VIB Dual 12 Y N/A N QFN-14 2.5 kVrms
Si8275GB-IM1 VIA/VIB Dual 3 N N/A Y QFN-14 2.5 kVrms
Si8275GBD-IM1 VIA/VIB Dual 3 Y N/A N QFN-14 2.5 kVrms
Si8275DA-IM1 VIA/VIB Dual 12 N N/A Y QFN-14 1 kVrms
Si8275DAD-IM1 VIA/VIB Dual 12 Y N/A N QFN-14 1 kVrms
Si827x Data Sheet
Ordering Guide
silabs.com | Building a more connected world. Rev. 1.01 | 3
Automotive Grade OPNs
Automotive-grade devices are built using automotive-specific flows at all steps in the manufacturing process to ensure robustness and
low defectivity. These devices are supported with AIAG-compliant Production Part Approval Process (PPAP) documentation, and fea-
ture International Material Data System (IMDS) and China Automotive Material Data System (CAMDS) listing. Qualifications are compli-
ant with AEC-Q100, and a zero-defect methodology is maintained throughout definition, design, evaluation, qualification, and mass pro-
duction steps.
Table 1.2. Ordering Guide for Automotive Grade OPNs1, 2, 4, 5
Ordering Part
Numbers (OPNs)
Inputs Driver Configu-
ration
Output
UVLO
Integrated
Deglitcher
Dead Time
Adjustable
Range
Low
Jitter
Package Isolation
Rating
Si8271AB-AS VI Single 5 N N/A Y SOIC-8 NB 2.5 kVrms
Si8271BB-AS VI Single 8 N N/A Y SOIC-8 NB 2.5 kVrms
Si8271DB-AS VI Single 12 N N/A Y SOIC-8 NB 2.5 kVrms
Si8273DB-AS1 VIA/VIB HS/LS 12 N N/A Y SOIC-16 NB 2.5 kVrms
Si8274BB4D-AS1 PWM HS/LS 8 Y 20-700 N SOIC-16 NB 2.5 kVrms
Si8274DB1-AS1 PWM HS/LS 12 N 10-100 Y SOIC-16 NB 2.5 kVrms
Si8275DB-AS1 VIA/VIB Dual 12 N N/A Y SOIC-16 NB 2.5 kVrms
Note:
1. All packages are RoHS-compliant with peak reflow temperatures of 260 °C according to the JEDEC industry standard classifica-
tions.
2. “Si” and “SI” are used interchangeably.
3. An "R" at the end of the part number denotes tape and reel packaging option.
4. Automotive-Grade devices (with an "–A" suffix) are identical in construction materials, topside marking, and electrical parameters
to their Industrial-Grade (with a "–I" suffix) version counterparts. Automotive-Grade products are produced utilizing full automotive
process flows and additional statistical process controls throughout the manufacturing flow. The Automotive-Grade part number is
included on shipping labels.
5. Additional Ordering Part Numbers may be available in Automotive-Grade. Please contact your local Silicon Labs sales represen-
tative for further information.
6. Referring to Section 8 Top Marking, the Manufacturing Code represented by either “RTTTTT” or “TTTTTT” contains as its first
character a letter in the range N through Z to indicate Automotive-Grade.
Si827x Data Sheet
Ordering Guide
silabs.com | Building a more connected world. Rev. 1.01 | 4
Table of Contents
1. Ordering Guide ..............................
2
2. System Overview ..............................7
2.1 Typical Operating Characteristics........................10
2.2 Family Overview and Logic Operation During Startup .................11
2.2.1 Products ..............................11
2.2.2 Device Behavior ............................11
2.3 Power Supply Connections ..........................13
2.4 Power Dissipation Considerations .......................13
2.5 Layout Considerations ...........................14
2.6 Undervoltage Lockout Operation ........................15
2.6.1 Device Startup ............................15
2.6.2 Undervoltage Lockout ..........................15
2.6.3 Control Inputs .............................15
2.6.4 Enable Input .............................16
2.7 Programmable Dead Time and Overlap Protection ..................16
2.8 De-glitch Feature .............................17
3. Applications............................... 18
3.1 High-Side/Low-Side Driver ..........................18
3.2 Dual Driver ...............................19
4. Electrical Specifications ..........................20
4.1 Test Circuits ...............................23
4.2 Regulatory Information (Pending)........................24
5. Pin Descriptions .............................29
5.1 Si8271 Pin Descriptions ...........................29
5.2 Si8273/75 Pin Descriptions ..........................30
5.3 Si8274 Pin Descriptions ...........................31
6. Package Outlines .............................32
6.1 Package Outline: 16-Pin Narrow-Body SOIC ....................32
6.2 Package Outline: 8-Pin Narrow Body SOIC ....................34
6.3 Package Outline: 14 LD QFN .........................36
7. Land Patterns ..............................37
7.1 Land Pattern: 16-Pin Narrow Body SOIC .....................37
7.2 Land Pattern: 8-Pin Narrow Body SOIC .....................38
7.3 Land Pattern: 14 LD QFN ..........................39
8. Top Markings ..............................40
8.1 Si827x Top Marking (16-Pin Narrow Body SOIC) ..................40
silabs.com | Building a more connected world. Rev. 1.01 | 5
2. System Overview
Si8271
UVLO
VDD
VO+
GNDA
VDDI
VI
ISOLATION
UVLO
GNDI
VDDI
VDDI
EN
VO-
Figure 2.1. Si8271 Block Diagram
Si8273
UVLO
UVLO
GNDI
VIB
VDDI
VIA VDDA
VOA
GNDA
VOB
VDDI
VDDI
ISOLATION
VDDI
VDDB
GNDB
EN
ISOLATION
UVLO
OVERLAP
PROTECTION
Figure 2.2. Si8273 Block Diagram
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 7
Si8274
UVLO
UVLO
GNDI
VDDI
PWM VDDA
VOA
GNDA
VOB
VDDI
VDDI
ISOLATION
VDDI
VDDB
GNDB
EN
ISOLATION
UVLO
DT CONTROL
&
OVERLAP
PROTECTION
DT
LPWM
LPWM
Figure 2.3. Si8274 Block Diagram
Si8275
UVLO
VDDA
VOA
GNDA
VOB
VDDI
ISOLATION
VDDI
VDDB
GNDB
UVLO
VIA
ISOLATION
UVLO
GNDI
VIB
VDDI
VDDI
EN
Figure 2.4. Si8275 Block Diagram
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 8
The operation of an Si827x channel is analogous to that of an optocoupler and gate driver, except an RF carrier is modulated instead of
light. This simple architecture provides a robust isolated data path and requires no special considerations or initialization at start-up. A
simplified block diagram for a single Si827x channel is shown in the figure below.
RF
OSCILLATOR
MODULATOR DEMODULATOR
AB
Semiconductor-
Based Isolation
Barrier
Transmitter Receiver
Dead
time
control 4 A peak
Gnd
VDD
Driver
Figure 2.5. Simplified Channel Diagram
A channel consists of an RF Transmitter and RF Receiver separated by a semiconductor-based isolation barrier. Referring to the
Transmitter, input A modulates the carrier provided by an RF oscillator using on/off keying. The Receiver contains a demodulator that
decodes the input state according to its RF energy content and applies the result to output B via the output driver. This RF on/off keying
scheme is superior to pulse code schemes as it provides best-in-class noise immunity, low power consumption, and better immunity to
magnetic fields. See Figure 2.6 Modulation Scheme on page 9 for more details.
Input Signal
Output Signal
Modulation Signal
Figure 2.6. Modulation Scheme
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 9
2.1 Typical Operating Characteristics
The typical performance characteristics depicted in the figures below are for information purposes only. Refer to Table 4.1 Electrical
Characteristics on page 20 for actual specification limits.
Figure 2.7. Rise/Fall Time vs. Supply Voltage Figure 2.8. Propagation Delay vs. Supply Voltage
Figure 2.9. Supply Current vs. Supply Voltage Figure 2.10. Supply Current vs. Supply Voltage
Figure 2.11. Supply Current vs. Temperature Figure 2.12. Rise/Fall Time vs. Load
Figure 2.13. Propagation Delay vs. Load Figure 2.14. Propagation Delay vs. Temperature
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 10
Figure 2.15. Output Sink Current vs. Temperature Figure 2.16. Output Source Current vs. Temperature
2.2 Family Overview and Logic Operation During Startup
The Si827x family of isolated drivers consists of single, high-side/low-side, and dual driver configurations.
2.2.1 Products
The table below shows the configuration and functional overview for each product in this family.
Table 2.1. Si827x Family Overview
Part Number Configuration Overlap
Protection
Programmable
Dead Time
Inputs Peak Output
Current (A)
Si8271 Single Driver — — VI 4.0
Si8273 High-Side/Low-Side Y — VIA, VIB 4.0
Si8274 PWM Y Y PWM 4.0
Si8275 Dual Driver — — VIA, VIB 4.0
2.2.2 Device Behavior
The following table consists of truth tables for the Si8273, Si8274, and Si8275 families.
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 11
Table 2.2. Si827x Family Truth Table1
Si8271 (Single Driver) Truth Table
Inputs VDDI State Enable Output Notes
VI VO+ VO–
L Powered H Hi–Z L
H Powered H H Hi–Z
X2Unpowered X Hi–Z L
X Powered L Hi–Z L
Si8273 (High-Side/Low-Side) Truth Table
Inputs VDDI State Enable Output Notes
VIA VIB VOA VOB
L L Powered H L L
L H Powered H L H
H L Powered H H L
H H Powered H L L Invalid state.
X2X2Unpowered X L L Output returns to input state within 7 µs of VDDI power restoration.
X X Powered L L L Device is disabled.
Si8274 (PWM Input High-Side/Low-Side) Truth Table
PWM Input VDDI State Enable Output Notes
VOA VOB
H Powered H H L
L Powered H L H
X2Unpowered X L L Output returns to input state within 7 µs of VDDI power restoration.
X Powered L L L Device is disabled.
Si8275 (Dual Driver) Truth Table
Inputs VDDI State Enable Output Notes
VIA VIB VOA VOB
L L Powered H L L
L H Powered H L H
H L Powered H H L
H H Powered H H H
X2X2Unpowered X L L Output returns to input state within 7 µs of VDDI power restoration.
X X Powered L L L Device is disabled.
1. This truth table assumes VDDA and VDDB are powered. If VDDA and VDDB are below UVLO, see 2.6.2 Undervoltage Lockout
for more information.
2. An input can power the input die through an internal diode if its source has adequate current.
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 12
2.3 Power Supply Connections
Isolation requirements mandate individual supplies for VDDI, VDDA, and VDDB. The decoupling caps for these supplies must be
placed as close to the VDD and GND pins of the Si827x as possible. The optimum values for these capacitors depend on load current
and the distance between the chip and the regulator that powers it. Low effective series resistance (ESR) capacitors, such as Tantalum,
are recommended.
2.4 Power Dissipation Considerations
Proper system design must assure that the Si827x operates within safe thermal limits across the entire load range.The Si827x total
power dissipation is the sum of the power dissipated by bias supply current, internal parasitic switching losses, and power dissipated by
the series gate resistor and load. The equation below shows total Si827x power dissipation.
PD=
(
VDDI
)(
IDDI
)
+ 2
(
IDD2
)(
VDD2
)
+ ( f)
(
QG
)
(
VDD2
)
Rp
Rp+Rg
+
(
f
)(
QG
)(
VDD2
)
Rn
Rn+Rg
+ 2 fCintVDD22
where:
PD is the total Si827x device power dissipation (W)
IDDI is the input-side maximum bias current (10 mA)
IDD2 is the driver die maximum bias current (4 mA)
Cint is the internal parasitic capacitance (370 pF)
VDDI is the input-side VDD supply voltage (2.5 to 5.5 V)
VDD2 is the driver-side supply voltage (4.2 to 30 V)
f is the switching frequency (Hz)
QG is the gate charge of external FET
RG is the external gate resistor
RP is the RDS(ON) of the driver pull-up switch: 2.7 Ω
Rn is the RDS(ON) of the driver pull-down switch: 1 Ω
Equation 1
Power dissipation example for driver using Equation 1 with the following givens:
VDDI = 5.0 V
VDD2 = 12 V
f = 350 kHz
RG = 22 Ω
QG = 25 nC
Pd = 199 mW
From which the driver junction temperature is calculated using Equation 2, where:
Pd is the total Si827x device power dissipation (W)
θja is the thermal resistance from junction to air (105 °C/W in this example)
TA is the ambient temperature
Tj=Pd×θja +TA= (0.199)(105) + 20 = 41.0 ° C
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 13
The maximum power dissipation allowable for the Si827x is a function of the package thermal resistance, ambient temperature, and
maximum allowable junction temperature, as shown in Equation 2:
PDmax ≤
Tjmax −TA
θja
where:
PDmax = Maximum Si827x power dissipation (W)
Tjmax = Si827x maximum junction temperature (150 °C)
TA = Ambient temperature (20 °C)
θja = Si827x junction-to-air thermal resistance (105 °C/W)
Equation 2
Substituting values for PDmax Tjmax, TA, and θja into Equation 2 results in a maximum allowable total power dissipation of 1.23 W. Maxi-
mum allowable load is found by substituting this limit and the appropriate data sheet values from Table 4.1 Electrical Characteristics on
page 20 into Equation 1 and simplifying. The result is Equation 3, which assumes VDDI = 5 V and VDDA = VDDB = 12 V.
Qg(max ) =0.596
f− 5.81 × 10−8
Equation 3
0
2
4
6
8
10
12
50 150 250 350 450 550 650 750
Max Charge Load (uC)
Switching Frequency (kHz)
Max Load vs. Switching Frequency
Figure 2.17. Max Load vs. Switching Frequency
2.5 Layout Considerations
It is most important to minimize ringing in the drive path and noise on the Si827x VDD lines. Care must be taken to minimize parasitic
inductance in these paths by locating the Si827x as close to the device it is driving as possible. In addition, the VDD supply and ground
trace paths must be kept short. For this reason, the use of power and ground planes is highly recommended. A split ground plane sys-
tem having separate ground and VDD planes for power devices and small signal components provides the best overall noise perform-
ance.
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 14
2.6 Undervoltage Lockout Operation
Device behavior during start-up, normal operation and shutdown is shown in the figure below, where UVLO+ and UVLO- are the posi-
tive-going and negative-going thresholds respectively.
Note: Outputs VOA and VOB default low when input side power supply (VDDI) is not present.
2.6.1 Device Startup
Outputs VOA and VOB are held low during power-up until VDD is above the UVLO threshold for time period tSTART. Following this,
the outputs follow the states of inputs VIA and VIB.
2.6.2 Undervoltage Lockout
Undervoltage Lockout (UVLO) is provided to prevent erroneous operation during device startup and shutdown or when VDD is below its
specified operating circuits range. The input (control) side, Driver A and Driver B, each have their own undervoltage lockout monitors.
The Si827x input side enters UVLO when VDDI < VDDIUV–, and exits UVLO when VDDI > VDDIUV+. The driver outputs, VOA and VOB,
remain low when the input side of the Si827x is in UVLO and their respective VDD supply (VDDA, VDDB) is within tolerance. Each
driver output can enter or exit UVLO independently. For example, VOA unconditionally enters UVLO when VDDA falls below VDDAUV–
and exits UVLO when VDDA rises above VDDAUV+.
The UVLO circuit unconditionally drives VO low when VDD is below the lockout threshold. Upon power up, the Si827x is maintained in
UVLO until VDD rises above VDDUV+. During power down, the Si827x enters UVLO when VDD falls below the UVLO threshold plus
hysteresis (i.e., VDD < VDDUV+ – VDDHYS). Please refer to spec tables for UVLO values.
VIA
VOA
ENABLE
VDDI
UVLO-
VDDA
tSTART tSTART tSTART tSD tRESTART tPHL tPLH
UVLO+
UVLO-
UVLO+
tSD
VDDHYS
VDDHYS
Figure 2.18. Device Behavior during Normal Operation and Shutdown
2.6.3 Control Inputs
VIA, VIB, and PWM inputs are high-true, TTL level-compatible logic inputs. A logic high signal on VIA or VIB causes the corresponding
output to go high. For PWM input versions (Si8274), VOA is high and VOB is low when the PWM input is high, and VOA is low and
VOB is high when the PWM input is low.
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 15
2.6.4 Enable Input
When brought low, the ENABLE input unconditionally drives VOA and VOB low regardless of the states of VIA and VIB. Device opera-
tion terminates within tSD after ENABLE = VIL and resumes within tRESTART after ENABLE = VIH. The ENABLE input has no effect if
VDDI is below its UVLO level (i.e., VOA, VOB remain low).
2.7 Programmable Dead Time and Overlap Protection
All PWM drivers (Si8274x) include programmable dead time, which adds a user-programmable delay between transitions of VOA and
VOB. When enabled, dead time is present on all transitions. The amount of dead time delay (DT) is programmed by a single resistor
(RDT) connected from the DT input to ground per the equation below.
DT= 2.02 × RDT + 7.77 (for 10-200 ns range)
DT = 6.06 × RDT + 3.84 (for 20-700 ns range)
where:
DT = dead time (ns)
and
RDT = dead time programming resistor (kΩ)
Equation 4
Input/output timing waveforms for the Si8273 two-input drivers are shown in the figure below, and dead time waveforms for the Si8274
are shown in Figure 2.20 Dead Time Waveforms for Si8274 Drivers on page 17.
VIA
VIB
VOA
VOB
A B C D E F G H I
Figure 2.19. Input / Output Waveforms for Si8273 Drivers
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 16
Table 2.3. Input / Output Waveforms for High-Side / Low-Side Two-Input Drivers
Ref Description
ANormal operation: VIA high, VIB low.
BNormal operation: VIB high, VIA low.
CContention: VIA = VIB = high.
DRecovery from contention: VIA transitions low.
ENormal operation: VIA = VIB = low.
FNormal operation: VIA high, VIB low.
GContention: VIA = VIB = high.
HRecovery from contention: VIB transitions low.
INormal operation: VIB transitions high.
PWM
LPWM
(internal)
VOA
VOB
DT
DT
10%
10%
90%
90%
50%
VOB
Typical Dead Time Operation
Figure 2.20. Dead Time Waveforms for Si8274 Drivers
2.8 De-glitch Feature
A de-glitch feature is provided on some options, as defined in the 1. Ordering Guide. The internal de-glitch circuit provides an internal
time delay of 15 ns typical, during which any noise is ignored and will not pass through the IC. For these product options, the propaga-
tion delay will be extended by 15 ns, as specified in the spec table.
Si827x Data Sheet
System Overview
silabs.com | Building a more connected world. Rev. 1.01 | 17
3. Applications
The following examples illustrate typical circuit configurations using the Si827x.
3.1 High-Side/Low-Side Driver
In the figure below, side A shows the Si8273 controlled using the VIA and VIB input signals, and side B shows the Si8274 controlled by
a single PWM signal.
Si8273
CB
1500 V max
VIA
VDDA
VOA
GNDA
VOB
ENABLE
VDD2
CONTROLLER
VIB
OUT1
OUT2
I/O
Q1
Q2
D1
C3
1 µF
Si8274
CB
PWM
VDDA
VOA
GNDA
VOB
VDDB
GNDB
ENABLE
DT
RDT
CONTROLLER
PWMOUT
I/O
Q1
Q2
D1
A B
VDD2
C3
1 µF
1500 V max
GNDI
VDDI
VDDI
C2
0.1 µF
C1
1 µF
VDD2
C4
0.1 µF C5
10 µF
VDDB
GNDB
GNDI
VDDI
VDDI
C2
0.1 µF
C1
1 µF
VDD2
C4
0.1 µF C5
10 µF
Figure 3.1. Si827x in Half-Bridge Application
For both cases, D1 and CB form a conventional bootstrap circuit that allows VOA to operate as a high-side driver for Q1, which has a
maximum drain voltage of 1500 V. VOB is connected as a conventional low-side driver. Note that the input side of the Si827x requires
VDD in the range of 2.5 to 5.5 V, while the VDDA and VDDB output side supplies must be between 4.2 and 30 V with respect to their
respective grounds. The boot-strap start up time will depend on the CB cap chosen. VDD2 is usually the same as VDDB. Also note that
the bypass capacitors on the Si827x should be located as close to the chip as possible. Moreover, it is recommended that bypass ca-
pacitors be used (as shown in the figures above for input and driver side) to reduce high frequency noise and maximize performance.
The outputs VOA and VOB can be used interchangeably as high side or low side drivers.
Si827x Data Sheet
Applications
silabs.com | Building a more connected world. Rev. 1.01 | 18
3.2 Dual Driver
The figure below shows the Si827x configured as a dual driver. Note that the drain voltages of Q1 and Q2 can be referenced to a com-
mon ground or to different grounds with as much as 1500 V dc between them.
Si8275
GNDI
VDDI
VIA VDDA
VOA
GNDA
VOB
VDDI
VDDB
GNDB
ENABLE
CONTROLLER
VIB
OUT1
OUT2
I/O
Q2
VDDA
VDDB
C2
0.1 µF
C1
1 µF
C3
0.1 µF C4
10 µF
C5
0.1 µF C6
10 µF
Q1
Figure 3.2. Si827x in a Dual Driver Application
Because each output driver resides on its own die, the relative voltage polarities of VOA and VOB can reverse without damaging the
driver. That is, the voltage at VOA can be higher or lower than that of VOB by VDD without damaging the driver. Therefore, a dual
driver in a high-side/low-side drive application can use either VOA or VOB as the high side driver. Similarly, a dual driver can operate
as a dual low-side or dual high-side driver and is unaffected by static or dynamic voltage polarity changes.
Si827x Data Sheet
Applications
silabs.com | Building a more connected world. Rev. 1.01 | 19
4. Electrical Specifications
Table 4.1. Electrical Characteristics
VDDI = 5 V, GNDI = 0 V, VDDA/B-GNDA/B = 30 V, TA = –40 to +125 °C; typical specs at 25 °C
Parameter Symbol Test Condition Min Typ Max Units
DC Parameters
Input Supply Voltage VDDI 2.5 — 5.5 V
Driver Supply Voltage (VDDA/B – GNDA/B) 4.2 — 30 V
Input Supply Quiescent Current IDDI(Q) — 7.9 10.0 mA
Input Supply Active Current IDDI f = 500 kHz — 8.0 10.0 mA
Output Supply Quiescent Current IDDx(Q) — 2.5 4.0 mA
Output Supply Active Current IDDx f = 500 kHz (no load) — 10.0 11.0 mA
Gate Driver
High Output Transistor RDS (ON) ROH — 2.7 — Ω
Low Output Transistor RDS (ΟΝ) ROL — 1.0 — Ω
High Level Peak Output Current IOH VDDA/B = 15 V,
See Figure 4.2 IOH
Source Current Test
Circuit on page 23
for Si827xG,
VDD = 4.2 V,
T < 250 ns
— 1.8 — A
Low Level Peak Output Current IOL VDDA/B = 15 V,
See Figure 4.1 IOL
Sink Current Test Cir-
cuit on page 23
for Si827xG,
VDD = 4.2 V,
TPW_IOL < 250 ns
— 4.0 — A
UVLO
VDDI UVLO Threshold + VDDIUV+ 1.85 2.2 2.45 V
VDDI UVLO Threshold – VDDIUV– 1.75 2.1 2.35 V
VDDI Hysteresis VDDIHYS — 100 — mV
UVLO Threshold + (Driver Side)
3 V Threshold VDDXUV+ 2.7 3.5 4.0 V
5 V Threshold 4.9 5.5 6.3 V
8 V Threshold 7.2 8.3 9.5 V
12 V Threshold 11 12.2 13.5 V
UVLO Threshold - (Driver Side)
Si827x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 1.01 | 20
Parameter Symbol Test Condition Min Typ Max Units
3 V Threshold VDDXUV- 2.5 3.0 3.8 V
5 V Threshold 4.6 5.2 5.9 V
8 V Threshold 6.7 7.8 8.9 V
12 V Threshold 9.6 10.8 12.1 V
UVLO Lockout Hysteresis
3 V Threshold VDDHYS — 500 — mV
5 V Threshold — 300 — mV
8 V Threshold — 500 — mV
12 V Threshold — 1400 — mV
Digital
Logic High Input Threshold VIH 2.0 — — V
Logic Low Input Threshold VIL — — 0.8 V
Input Hysteresis VIHYST 350 400 — mV
Logic High Output Voltage VOH IO = –1 mA VDDA/B –
0.04
— — V
Logic Low Output Voltage VOL IO = 1 mA — — 0.04 V
AC Switching Parameters
Propagation Delay
Si8271/3/5 with low jitter
tPLH, tPHL CL = 200 pF 20 30 60 ns
Propagation Delay
Si8271/3/5 with de-glitch option
tPLH, tPHL CL = 200 pF 30 45 75 ns
Propagation Delay
Si8274 with low jitter
tPHL CL = 200 pF 20 30 60 ns
Propagation Delay
Si8274 with de-glitch option
tPHL CL = 200 pF 30 45 75 ns
Propagation Delay
Si8274 with low jitter
tPLH CL = 200 pF 30 45 75 ns
Propagation Delay
Si8274 with de-glitch option
tPLH CL = 200 pF 65 85 105 ns
Pulse Width Distortion
Si8271/3/5 all options
PWD |tPLH – tPHL| — 3.6 8 ns
Pulse Width Distortion
Si8274 with low jitter
PWD |tPLH – tPHL| — 14 19 ns
Pulse Width Distortion
Si8274 with de-glitch option
PWD |tPLH – tPHL| — 38 47 ns
Peak to Peak Jitter
Si827x with low jitter
— 200 — ps
Si827x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 1.01 | 21
Parameter Symbol Test Condition Min Typ Max Units
Programmed dead-time (DT) for
products with 10–200 ns DT range
DT RDT = 6 kΩ 10 20 30 ns
RDT = 15 kΩ 26 38 50
RDT = 100 kΩ 150 210 260
Programmed dead-time (DT) for
products with 20–700 ns DT range
DT RDT = 6 kΩ 23 40 57 ns
RDT = 15 kΩ 60 95 130
RDT = 100 kΩ 450 610 770
Rise time tRCL = 200 pF 4 10.5 16 ns
Fall time tFCL = 200 pF 5.5 13.3 18 ns
Shutdown Time from
Enable False
tSD — — 60 ns
Restart Time from
Enable True
tRESTART — — 60 ns
Device Startup Time tSTART — 16 30 µs
Common Mode Transient
Immunity
Si827x with de-glitch option
See Figure 4.3 Com-
mon Mode Transient
Immunity Test Circuit
on page 24.
VCM = 1500 V
200 350 400 kV/µs
Common Mode Transient
Immunity
Si827x with low jitter option
See Figure 4.3 Com-
mon Mode Transient
Immunity Test Circuit
on page 24.
VCM = 1500 V
150 300 400 kV/µs
Si827x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 1.01 | 22
4.1 Test Circuits
The figures below depict sink current, source current, and common-mode transient immunity test circuits.
INPUT
1 µF 100 µF
10
RSNS
0.1
Si827x
1 µF
CER
10 µF
EL
VDDA = VDDB = 15 V
IN OUT
GND
VDD
SCHOTTKY
50 ns
200 ns
Measure
INPUT WAVEFORM
GND
VDDI
VDDI
8 V +
_
Figure 4.1. IOL Sink Current Test Circuit
INPUT
1 µF 100 µF
10
RSNS
0.1
Si827x
1 µF
CER
10 µF
EL
VDDA = VDDB = 15 V
IN OUT
GND
VDD
50 ns
200 ns
Measure
INPUT WAVEFORM
GND
VDDI
SCHOTTKY
VDDI
5.5 V +
_
Figure 4.2. IOH Source Current Test Circuit
Si827x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 1.01 | 23
Oscilloscope
5V
Isolated
Supply
VDDA
VOA
GNDA
12 V
Supply
High Voltage
Surge Generator
Vcm Surge
Output
100k
High Voltage
Differential
Probe
VDDB
VOB
GNDB
DT
GNDI
VDDI
INPUT
EN
Input Signal
Switch
Input
Output
Isolated
Ground
Si827x
Figure 4.3. Common Mode Transient Immunity Test Circuit
4.2 Regulatory Information (Pending)
Table 4.2. Regulatory Information1,2
CSA
The Si827x is certified under CSA Component Acceptance Notice 5A. For more details, see Master Contract Number 232873.
60950-1: Up to 125 VRMS reinforced insulation working voltage; up to 600 VRMS basic insulation working voltage.
VDE
The Si827x is certified according to VDE 0884-10. For more details, see Certificate 40018443.
VDE 0884-10: Up to 630 Vpeak for basic insulation working voltage.
UL
The Si827x is certified under UL1577 component recognition program. For more details, see File E257455.
Rated up to 2500 VRMS isolation voltage for basic protection.
CQC
The Si827x is certified under GB4943.1-2011. For more details, see Certificates CQC 16001160284 and CQC 17001177887.
Rated up to 125 VRMS reinforced insulation working voltage; up to 600 VRMS basic insulation working voltage.
1. Regulatory Certifications apply to 2.5 kVRMS rated devices which are production tested to 3.0 kVRMS for 1 sec.
2. For more information, see 1. Ordering Guide.
Si827x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 1.01 | 24
Table 4.3. Insulation and Safety-Related Specifications
Parameter Symbol Test Condition Value Unit
SOIC-8 NB SOIC-16 14 LD QFN
Nominal External Air Gap
(Clearance)
CLR 4.7 4.7 3.5 mm
Nominal External Tracking
(Creepage)
CPG 3.9 3.9 3.5 mm
Minimum Internal Gap
(Internal Clearance)
DTI 0.008 0.008 0.008 mm
Tracking Resistance PTI or CTI IEC60112 600 600 600 V
Erosion Depth ED 0.019 0.019 0.021 mm
Resistance
(Input-Output)1
RIO 1012 1012 1012 Ω
Capacitance
(Input-Output)1
CIO f = 1 MHz 0.5 0.5 0.5 pF
Input Capacitance2CI3.0 3.0 3.0 pF
Notes:
1. To determine resistance and capacitance, the Si827x is converted into a 2-terminal device. All pins on side 1 are shorted to cre-
ate terminal 1, and all pins on side 2 are shorted to create terminal 2. The parameters are then measured between these two
terminals.
2. Measured from input pin to ground.
Table 4.4. IEC 60664-1 Ratings
Parameter Test Condition Specification
SOIC-8 NB SOIC-16 14 LD QFN
Basic Isolation Group Material Group I I I
Installation Classification Rated Mains Voltages < 150 VRMS I-IV I-IV I-IV
Rated Mains Voltages < 300 VRMS I-III I-III I-III
Rated Mains Voltages < 400 VRMS I-II I-II I-II
Rated Mains Voltages < 600 VRMS I-II I-II I-II
Si827x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 1.01 | 25
Table 4.5. VDE 0884 Insulation Characteristics1
Parameter Symbol Test Condition Characteristic Unit
Maximum Working Insulation Voltage VIORM 630 V peak
Input to Output Test Voltage VPR Method b1
(VIORM x 1.875 = VPR, 100%
Production Test, tm = 1 sec,
Partial Discharge < 5 pC)
1181 V peak
Transient Overvoltage VIOTM t = 60 sec 4000 V peak
Surge Voltage VIOSM Tested per IEC 60065 with surge
voltage of 1.2 µs/50 µs
Tested with 4000 V
3077 Vpeak
Pollution Degree
(DIN VDE 0110, Table 1)
2
Insulation Resistance at
TS, VIO = 500 V
RS>109Ω
Note:
1. Maintenance of the safety data is ensured by protective circuits. The Si827x provides a climate classification of 40/125/21.
Table 4.6. IEC Safety Limiting Values1
Parameter Symbol Test Condition SOIC-8 NB SOIC-16 14 LD QFN Unit
Safety
Temperature
TS150 150 150 °C
Safety Input Current ΙSθJA = 110 °C/W
(SOIC-8),
105 °C/W
(NB SOIC-16, 14 LD QFN),
VDDI = 5.5 V,
VDDA = VDDB = 30 V,
TJ = 150 °C,
TA = 25 °C
35 40 40 mA
Device Power Dissipation PD1.1 1.2 1.2 W
Note:
1. Maximum value allowed in the event of a failure. Refer to the thermal derating curve in the two figures below.
Si827x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 1.01 | 26
Table 4.7. Thermal Characteristics
Parameter Symbol SOIC-8 NB
SOIC-16
14 LD QFN Unit
IC Junction-to-Air
Thermal Resistance
θJA 110 105 105 °C/W
0 20015010050
60
40
20
0
Temperature (ºC)
Safety-Limiting Current (mA)
VDDI = 5.5 V
VDDA, VDDB = 30 V
10
30
50
Figure 4.4. NB SOIC-16, QFN-14 Thermal Derating Curve, Dependence of Safety Limiting Values Limiting Values per VDE
0 20014010060
60
40
20
0
Temperature (ºC)
Safety-Limiting Current (mA)
10
30
50
VDDI = 5.5 V
VDDA, VDDB = 30 V
Figure 4.5. NB SOIC-8 Thermal Derating Curve, Dependence of Safety Limiting Values
Limiting Values per VDE
Si827x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 1.01 | 27
Table 4.8. Absolute Maximum Ratings1
Parameter Symbol Min Max Units
Storage Temperature TSTG –65 +150 °C
Operating Temperature TA–40 +125 °C
Junction Temperature TJ— +150 °C
Input-side supply voltage VDDI –0.6 6.0 V
Driver-side supply voltage VDDA, VDDB –0.6 36 V
Voltage on any pin with respect to ground2VIO –0.5 VDD + 0.5 V
Peak Output Current (tPW = 10 µs, duty cycle = 0.2%) IOPK — 4.0 A
Lead Solder Temperature (10 s) — 260 °C
HBM Rating ESD — 3.5 kV
CDM — 2000 V
Maximum Isolation Voltage (Input to Output) (1 sec)
NB SOIC-16 and SOIC-8
— 3000 VRMS
Maximum Isolation Voltage (Input to Output) (1 sec)
QFN-14
— 3000 VRMS
Maximum Isolation Voltage (Output to Output) (1 sec)
NB SOIC-16
— 1500 VRMS
Maximum Isolation Voltage (Output to Output) (1 sec)
QFN-14
— 650 VRMS
Latch-up Immunity — 400 kV/μs
Note:
1. Permanent device damage may occur if the absolute maximum ratings are exceeded. Functional operation should be restricted to
the conditions specified in the operational sections of this data sheet.
2. The voltage on VO+ or the voltages on VOA/VOB with respect to ground are allowed to be -1.0V (min) for 200 ns
Si827x Data Sheet
Electrical Specifications
silabs.com | Building a more connected world. Rev. 1.01 | 28
5. Pin Descriptions
5.1 Si8271 Pin Descriptions
Si8271
VDD
VO+
VO-
GND
VDDI
VI
GNDI
EN
1
2
3
4
8
7
6
5
Figure 5.1. Pin Assignments Si8271
Table 5.1. Si8271 Pin Descriptions
Pin Name Description
1 VI Digital driver control signal
2 VDDI Input side power supply
3 GNDI Input side ground
4 EN Enable
5 GND Driver side ground
6 VO– Gate drive pull low
7 VO+ Gate drive pull high
8 VDD Driver side power supply
Si827x Data Sheet
Pin Descriptions
silabs.com | Building a more connected world. Rev. 1.01 | 29
5.2 Si8273/75 Pin Descriptions
Si8273
Si8275
VDDA
VOA
GNDA
NC
NC
VDDB
VOB
GNDB
VDDI
VIA
VIB
GNDI
NC
EN
NC
VDDI
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
Si8273
Si8275
1
2
3
4
5
6
7
14
13
12
11
10
9
8
VIB
NC
VIA
GNDI
NC
EN
VDDI
VDDA
VOA
GNDA
NC
VDDB
VOB
GNDB
Figure 5.2. Pin Assignments Si8273/5
Table 5.2. Si8273/5 Pin Descriptions
NB SOIC-16 Pin # QFN-14 Pin # Name Description
1 2 VIA Digital driver control signal for “A” driver
2 3 VIB Digital driver control signal for “B” driver
3,8 7 VDDI Input side power supply
4 4 GNDI Input side ground
5 5 EN Enable
6, 7, 12, 13 1, 6, 11 NC No Connect
9 8 GNDB Driver side power supply for “B” driver
10 9 VOB Gate drive output for “B” driver
11 10 VDDB Driver side power supply for “B” driver
14 12 GNDA Driver side power supply for “A” driver
15 13 VOA Gate drive output for “A” driver
16 14 VDDA Driver side power supply for “A” driver
Si827x Data Sheet
Pin Descriptions
silabs.com | Building a more connected world. Rev. 1.01 | 30
5.3 Si8274 Pin Descriptions
Si8274
VDDA
VOA
GNDA
NC
NC
VDDB
VOB
GNDB
VDDI
PWM
NC
GNDI
DT
EN
NC
VDDI
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
Si8274
1
2
3
4
5
6
7
14
13
12
11
10
9
8
NC
NC
PWM
GNDI
DT
EN
VDDI
VDDA
VOA
GNDA
NC
VDDB
VOB
GNDB
Figure 5.3. Pin Assignments Si8274
Table 5.3. Si8274 Pin Descriptions
NB SOIC-16 Pin # QFN-14 Pin # Name Description
1 2 PWM Pulse width modulated driver control signal
2, 7, 12, 13 1, 3, 11 NC No Connect
3, 8 7 VDDI Input side power supply
4 4 GNDI Input side ground
5 5 EN Enable
6 6 DT Dead time control
9 8 GNDB Driver side power supply for “B” driver
10 9 VOB Gate drive output for “B” driver
11 10 VDDB Driver side power supply for “B” driver
14 12 GNDA Driver side power supply for “A” driver
15 13 VOA Gate drive output for “A” driver
16 14 VDDA Driver side power supply for “A” driver
Si827x Data Sheet
Pin Descriptions
silabs.com | Building a more connected world. Rev. 1.01 | 31
6. Package Outlines
6.1 Package Outline: 16-Pin Narrow-Body SOIC
The figure below illustrates the package details for the Si827x in a 16-pin narrow-body SOIC (SO-16). The table below lists the values
for the dimensions shown in the illustration.
Figure 6.1. 16-pin Small Outline Integrated Circuit (SOIC) Package
Si827x Data Sheet
Package Outlines
silabs.com | Building a more connected world. Rev. 1.01 | 32
Table 6.1. Package Diagram Dimensions
Dimension Min Max Dimension Min Max
A — 1.75 L 0.40 1.27
A1 0.10 0.25 L2 0.25 BSC
A2 1.25 — h 0.25 0.50
b 0.31 0.51 θ 0° 8°
c 0.17 0.25 aaa 0.10
D 9.90 BSC bbb 0.20
E 6.00 BSC ccc 0.10
E1 3.90 BSC ddd 0.25
e 1.27 BSC
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. This drawing conforms to the JEDEC Solid State Outline MS-012, Variation AC.
4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.
Si827x Data Sheet
Package Outlines
silabs.com | Building a more connected world. Rev. 1.01 | 33
6.2 Package Outline: 8-Pin Narrow Body SOIC
The figure below illustrates the package details for the Si827x in an 8-pin narrow-body SOIC package. The table below lists the values
for the dimensions shown in the illustration.
Figure 6.2. 8-Pin Narrow Body SOIC Package
Si827x Data Sheet
Package Outlines
silabs.com | Building a more connected world. Rev. 1.01 | 34
Table 6.2. 8-Pin Narrow Body SOIC Package Diagram Dimensions
Symbol Millimeters
Min Max
A 1.35 1.75
A1 0.10 0.25
A2 1.40 REF 1.55 REF
B 0.33 0.51
C 0.19 0.25
D 4.80 5.00
E 3.80 4.00
e 1.27 BSC
H 5.80 6.20
h 0.25 0.50
L 0.40 1.27
0° 8°
Si827x Data Sheet
Package Outlines
silabs.com | Building a more connected world. Rev. 1.01 | 35
6.3 Package Outline: 14 LD QFN
The figure below illustrates the package details for the Si827x in an QFN outline. The table below lists the values for the dimensions
shown in the illustration.
Figure 6.3. Si827x 14-pin LD QFN Outline
Table 6.3. Package Diagram Dimensions
Dimension MIN NOM MAX
A 0.74 0.84 0.90
A1 0 0.025 0.05
b 0.25 0.30 0.35
D 5.00 BSC
e 0.65 BSC
E 5.00 BSC
E1 3.60 BSC
L 0.50 0.60 0.70
L1 (3) — 0.10 BSC —
ccc — — 0.08
ddd — — 0.10
1. All dimensions shown are in millimeters (mm) unless otherwise noted.
2. Dimensioning and Tolerancing per ANSI Y14.5M-1994.
3. L1 shall not be less than 0.01 mm.
Si827x Data Sheet
Package Outlines
silabs.com | Building a more connected world. Rev. 1.01 | 36
7. Land Patterns
7.1 Land Pattern: 16-Pin Narrow Body SOIC
The figure below illustrates the recommended land pattern details for the Si827x in a 16-pin narrow-body SOIC. The table below lists
the values for the dimensions shown in the illustration.
Figure 7.1. 16-Pin Narrow Body SOIC PCB Land Pattern
Table 7.1. 16-Pin Narrow Body SOIC Land Pattern Dimensions
Dimension Feature (mm)
C1 Pad Column Spacing 5.40
E Pad Row Pitch 1.27
X1 Pad Width 0.60
Y1 Pad Length 1.55
Notes:
1. This Land Pattern Design is based on IPC-7351 pattern SOIC127P600X165-16N for Density Level B (Median Land Protrusion).
2. All feature sizes shown are at Maximum Material Condition (MMC) and a card fabrication tolerance of 0.05 mm is assumed.
Si827x Data Sheet
Land Patterns
silabs.com | Building a more connected world. Rev. 1.01 | 37
7.2 Land Pattern: 8-Pin Narrow Body SOIC
The figure below illustrates the recommended land pattern details for the Si827x in an 8-pin narrow-body SOIC. The table below lists
the values for the dimensions shown in the illustration.
Figure 7.2. 8-Pin Narrow Body SOIC Land Pattern
Table 7.2. 8-Pin Narrow Body SOIC Land Pattern Dimensions
Dimension Feature (mm)
C1 Pad Column Spacing 5.40
E Pad Row Pitch 1.27
X1 Pad Width 0.60
Y1 Pad Length 1.55
Notes:
1. This Land Pattern Design is based on IPC-7351 pattern SOIC127P600X173-8N for Density Level B (Median Land Protrusion).
2. All feature sizes shown are at Maximum Material Condition (MMC) and a card fabrication tolerance of 0.05 mm is assumed.
Si827x Data Sheet
Land Patterns
silabs.com | Building a more connected world. Rev. 1.01 | 38
7.3 Land Pattern: 14 LD QFN
The figure below illustrates the recommended land pattern details for the Si827x in a 14-pin QFN. The table below lists the values for
the dimensions shown in the illustration.
Figure 7.3. 14-Pin QFN Land Pattern
Table 7.3. 14-Pin QFN Land Pattern Dimensions
Dimension (mm)
C1 4.20
E 0.65
X1 0.80
Y1 0.40
Notes:
1. All dimensions shown are in millimeters (mm).
2. This Land Pattern Design is based on the IPC-7351 guidelines.
3. All dimensions shown are at Maximum Material Condition (MMC). Least Material Condition (LMC) is calculated based on a Fabri-
cation Allowance of 0.05 mm.
4. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 µm
minimum, all the way around the pad.
5. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release.
6. The stencil thickness should be 0.125 mm (5 mils).
7. The ratio of stencil aperture to land pad size should be 1:1.
8. A No-Clean, Type-3 solder paste is recommended.
9. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components.
Si827x Data Sheet
Land Patterns
silabs.com | Building a more connected world. Rev. 1.01 | 39
8. Top Markings
8.1 Si827x Top Marking (16-Pin Narrow Body SOIC)
Table 8.1. Top Marking Explanation (16-Pin Narrow Body SOIC)
Line 1 Marking: Base Part Number
Ordering Options
See 1. Ordering Guide for
more information.
Si827 = ISOdriver product series
Y = Configuration
3 = High-side/Low-side (HS/LS)
4 = PWM HS/LS
5 = Dual driver
U = UVLO level
G = 3 V
A = 5 V
B = 8 V
D = 12 V
V = Isolation rating
B = 2.5 kV
W = Dead-time setting range
1= 10-200 ns
4 = 20-700 ns
X = Integrated de-glitch circuit
D = integrated
none = not included
Line 2 Marking: YY = Year
WW = Workweek
Assigned by the Assembly House. Corresponds to the year and workweek
of the mold date.
TTTTTT = Mfg Code Manufacturing Code from Assembly Purchase Order form.
Si827x Data Sheet
Top Markings
silabs.com | Building a more connected world. Rev. 1.01 | 40
8.2 Si8271 Top Marking (8-Pin Narrow Body SOIC)
Table 8.2. Top Marking Explanation (Narrow Body SOIC)
Line 1 Marking: Customer Part Number Si827 = ISOdriver product series
Y = Configuration
1 = Single driver
U = UVLO level
G = 3 V
A = 5 V
B = 8 V
D = 12 V
V = Isolation rating
B = 2.5 kV
Line 2 Marking: WX = Ordering options W = Dead-time setting range
1= 10-200 ns
4 = 20-700 ns
X = Integrated de-glitch circuit
D = integrated
none = not included
YY = Year
WW = Work week
Assigned by the Assembly House. Corresponds to the year and workweek
of the mold date.
Line 3 Marking: TTTTTT = Mfg code Manufacturing Code from Assembly Purchase Order form.
Si827x Data Sheet
Top Markings
silabs.com | Building a more connected world. Rev. 1.01 | 41
8.3 Si827x Top Marking (14 LD QFN)
Table 8.3. Top Marking Explanation (14 LD QFN)
Line 1 Marking: Base Part Number
Ordering Options
See 1. Ordering Guide for
more information.
Si827 = ISOdriver product series
Y = configuration
1 = single driver
3 = High-side/Low-side (HS/LS)
4 = PWM HS/LS
5 = Dual driver
Line 2 Marking: Ordering Options U = UVLO level
G = 3 V
A = 5 V
B = 8 V
D = 12 V
V = Isolation rating
B = 2.5 kV
W = Dead-time setting range
1= 10-200 ns
4 = 20-700 ns
X = Integrated de-glitch circuit
D = integrated
none = not included
Line 3 Marking: TTTTTT = Mfg code Manufacturing Code from Assembly.
Line 4 Marking: Circle = 1.5 mm diameter Pin 1 identifier.
YYWW Manufacturing date code.
Si827x Data Sheet
Top Markings
silabs.com | Building a more connected world. Rev. 1.01 | 42
9. Revision History
Revision 1.01
April 2019
•Added Si8271AB-AS and Si8274BB4D-AS1 to Table 1.2 Ordering Guide for Automotive Grade OPNs on page 4.
Revision 1.0
May, 2018
• Replaced references and descriptions of LGA package with QFN package throughout the data sheet.
• Updated OPNs with LGA package denoted by -IM suffix to QFN packages denoted by -IM1 suffix in the Ordering Guide.
• Added Si8274DB1-AS1 OPN to Table 1.2 Ordering Guide for Automotive Grade OPNs on page 4.
• Added Note 6 to Table 1.2 Ordering Guide for Automotive Grade OPNs on page 4 referring to Top Markings for Automotive Grade
parts.
• Updated Equation 3 and the chart generated by Equation 3 in Figure 2.17 Max Load vs. Switching Frequency on page 14.
• Corrected power dissipation example calculations in Power Dissipation Considerations.
• Updated Package Outline: 14 LD QFN with new QFN package outline drawing and updated Table 6.3 Package Diagram Dimen-
sions on page 36 with QFN package dimensions.
• Updated Table 4.2 Regulatory Information on page 24 with certification information.
• Updated Table 4.3 Insulation and Safety-Related Specifications on page 25 symbols and clarified parameters.
• Added Surge Voltage specification to Table 4.5 VDE 0884 Insulation Characteristics on page 26.
• Updated description of Figure 4.4 NB SOIC-16, QFN-14 Thermal Derating Curve on page 27 and Figure 4.5 NB SOIC-8 Thermal
Derating Curve on page 27.
Revision 0.6
December, 2017
• Updated Figure 2.12 Rise/Fall Time vs. Load on page 10.
• Updated Table 4.1 Electrical Characteristics on page 20.
• Added "(no load)" under IDDx specification test condition.
• Added tSD and tRESTART specs.
•Corrected storage temp and power dissipation for SOIC-8 package in Table 4.6 IEC Safety Limiting Values1 on page 26.
•Added footnote about VO+ and VOA/VOB voltages with respect to ground in Table 4.8 Absolute Maximum Ratings1 on page 28 with
improvement from other pins.
• Added new table to Ordering Guide for Automotive-Grade OPN options.
Revision 0.5
February 26, 2016
• Initial release.
Si827x Data Sheet
Revision History
silabs.com | Building a more connected world. Rev. 1.01 | 43
Smart.
Connected.
Energy-Friendly.
Products
www.silabs.com/products
Quality
www.silabs.com/quality
Support and Community
community.silabs.com
http://www.silabs.com
Silicon Laboratories Inc.
400 West Cesar Chavez
Austin, TX 78701
USA
Disclaimer
Silicon Labs intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers using or
intending to use the Silicon Labs products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and "Typical"
parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Labs reserves the right to make changes without
further notice to the product information, specifications, and descriptions herein, and does not give warranties as to the accuracy or completeness of the included information. Without prior
notification, Silicon Labs may update product firmware during the manufacturing process for security or reliability reasons. Such changes will not alter the specifications or the performance
of the product. Silicon Labs shall have no liability for the consequences of use of the information supplied in this document. This document does not imply or expressly grant any license to
design or fabricate any integrated circuits. The products are not designed or authorized to be used within any FDA Class III devices, applications for which FDA premarket approval is required
or Life Support Systems without the specific written consent of Silicon Labs. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails,
can be reasonably expected to result in significant personal injury or death. Silicon Labs products are not designed or authorized for military applications. Silicon Labs products shall under no
circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons. Silicon Labs
disclaims all express and implied warranties and shall not be responsible or liable for any injuries or damages related to use of a Silicon Labs product in such unauthorized applications.
Trademark Information
Silicon Laboratories Inc.® , Silicon Laboratories®, Silicon Labs®, SiLabs® and the Silicon Labs logo®, Bluegiga®, Bluegiga Logo®, Clockbuilder®, CMEMS®, DSPLL®, EFM®, EFM32®,
EFR, Ember®, Energy Micro, Energy Micro logo and combinations thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZRadio®, EZRadioPRO®, Gecko®, Gecko
OS, Gecko OS Studio, ISOmodem®, Precision32®, ProSLIC®, Simplicity Studio®, SiPHY®, Telegesis, the Telegesis Logo®, USBXpress® , Zentri, the Zentri logo and Zentri DMS, Z-Wave®,
and others are trademarks or registered trademarks of Silicon Labs. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of ARM Holdings. Keil is a registered
trademark of ARM Limited. Wi-Fi is a registered trademark of the Wi-Fi Alliance. All other products or brand names mentioned herein are trademarks of their respective holders.
