Heavy Duty Vinyl Electrical Tape 22
Data Sheet July 2011
Description
Scotch® Heavy Duty Vinyl Electrical Tape 22 is a premium grade, 10-mil thick, vinyl
insulating tape. It is designed to perform continuously in ambient temperatures up to
80°C (176°F). The tape is conformable for cold weather applications down to
-10°C (15°F). It has excell ent resistance to abrasion, moisture, alkalies, acids,
corrosion and varying weather conditio ns. The combination of elastic backing an d
aggressive adhesive provides moisture-tight electrical and mechanical protection with
minimum bulk. Scotch® Tape 22 is an Und erwriters’ Laboratories Listed a nd
Canadian Standards Association Certified “Insulating Tape.”
Agency Approvals &
Self Certifications
UL Listed; UL 510 Standard “Insulating Tape” (product category OANZ), File E129200
CSA Certification; Standard C22.2 No. 197-M1983 “PVC Insulating Tape,” File
LR48769
RoHS 2002/95/EC
RoHS Compliant 2002/95/EC” means that the product or part (“Product”) does not contain any of the substances in
excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision
2005/618/EC, unless the substance is in an application that is exempt under RoHS. This information represents 3M’s
knowledge and belief, which may be based in whole or in part on information provided by third party suppliers to 3M.
Features
Polyvinyl chloride (PVC) backing
Pressure-sensitive rubber-based adhesive
Compatible with solid dielectric cable insulations
Inhibits corrosion of electrical conductors
For indoor or outdoor applications
Increased mechanical strength
Extra physical protection against abrasion
Applications
Primary electrical insulatio n for all wire and cable splices rated up to 600 volts and
80°C (176°F)
Primary electrical insulation for 600 -volt bus applications, and protective jacketing
for high- and low-voltage b us
Protective jacketing for high-voltage cable splices and repai rs
Harnessing of wires and cables
1 of 3 3
Scotch® Heavy Duty Vinyl Electrical Tape 22
2 of 3
Typical Properties
Not for specifications. Values are typical, not to be considered minimum or maxi mum.
Properties measured at room temperature 73°F (23°C) unless otherwise stated.
Physical Properties
(Test Method ASTM D-1000*) Typical Value
US units (metric)
Color Black
Thickness* 10 mils
Temperature Rating
UL 510
CSA C22.2 No 197-M1983
80ºC (176ºF)
80ºC (176ºF)
Adhesion to Steel*
22ºC (72ºF)
20 oz. /in. (2,2 N/10 mm)
Adhesion to Backing*
22ºC (72ºF)
20 oz. /in. (2,2 N/10 mm)
Breaking Strength*
22ºC (72ºF)
20 lbs./in. (35 N/10 mm)
Ultimate Elongation* 200%
Flagging* < 0.1 in. (2,5 mm)
Telescoping
24 hrs. W 50ºC (120ºF)
< 0.1 in. (2,5 mm)
Flammability
UL 510
Pass
Electrical Properties
(Test Method ASTM D-1000*) Typical Value
US units (metric)
Voltage Rating UL 510 600V
Dielectric Breakdow n*
Standard condition
High Humidity Condition
12,000 volts
90% of Standard
Insulation Resistance* > 1x 106 Megohms
Product
Specifications
Scotch® Heavy Duty Vinyl Electrical Tape 22 is based on polyvinyl chloride (PVC)
and/or its copolymers, and has a rubber-based, pressure-sensitive adhesive. The
tape shall be 10 mils thick, and be UL Listed and marked per UL Standard 51 0 as
“Flame-Retardant and Cold-Resistant.” The tape must be applied at temperatures
ranging from 15°F through 100°F (-10°C through 38°C), without loss of physical
properties. It shall be classified for use in both indoor and outdoor environments. The
tape shall be compatible with synthetic cable in sulations, jackets and splicing
compounds. Scotch® Tape 22 will remain stable and will not telescope more than 0.1
inches when maintained at temperature s belo w 12 0°F (50°C).
Scotch® Heavy Duty Vinyl Electrical Tape 22
3 of 3
Engineering/
Architectural
Specifications
Primary electrical insulation (branch wiring in wet or dry locations): All splices for
600-volt wire rated 80°C (176°F) and below shall be insulated with a minimum of two
half-lapped layers of Scotch® Heavy Duty Vinyl Electrical Tap e 22. All conne ctors
having irregular surfaces shall be padde d with 3M™ Scotchfil™ Electrical Insulation
Putty or Scotch® Linerless Rubber Splici ng Tape 130C prior to insulating with this
tape.
Mechanical Protection (outer jacketing)
All rubber and thermoplastic insulating high voltage power cable tape splices and
repairs shall be over wrapped with at least two half-lapped layers of Scotch® Tape 22.
Installation
Scotch® Tape 22 shall be applied in half-lapped layers with sufficient tension to
produce a uniform wind (for most applica tions this tension will re duce the tape’s width
to approximately 5/8 of its original width). On pigtail splices, the tape shall be
wrapped beyond the end of the wires and then folded back, leaving a protective
cushion to resist cut-through. Wrap tape up-hill, taping from a smaller diameter
surface to a larger diameter surface. Apply the tape with no tension on the last wrap
to prevent flagging.
Availability
Please contact your local distributor; av ailable from 3M.com/electrical [Where to Buy]
or call 1.800.245.3573.
Shelf Life & Storage
This product has a 5-year shelf life from date of manufacture when stored in a
humidity controlled storage (10° C/50ºF to 27°C/80ºF and <75% relative humidity).
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information
believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must
evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product, which are not contained in 3M’s current publications, or any
contrary statements contained on your purchase order, shall have no force or effect unless expressly agreed upon,
in writing, by an authorized officer of 3M.
Warranty; Limited Remedy;
Limited Liability
This product will be free from defects in material and manufacture at the time of purchase. 3M MAKES NO OTHER
WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above,
your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of
the 3M product. Except where prohibited by law, 3M will not be liable for any indirect, special, incidental or
consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.
3M, Scotch and Scotchfil are trademarks of 3M Company.
3
Electrical Markets Division
6801 River Place Blvd.
Austin, TX 78726-9000
800.245.3573
FAX: 800.245.0329
www.3M.com/electrical
Please recycle
© 3M 2011 All rights reserved
78-8124-4842-7 C
