CLL040-1218A1-50KL1A1 - Citizen - Datasheet.Directory

and are trademarks or registered trademarks of CITIZEN HOLDINGS CO., LTD. JAPAN.

is a trademark or a registered trademark of CITIZEN ELECTRONICS CO., LTD. JAPAN.

DATA SHEET

CLL040-1218A1-50KL1A1

Ref.CE-P1996 02/12 R1(0612)

1. Scope of Application

This data sheet is applied to the LED package, model CLL040-1218A1-50KL1A1.

2. Part code

[1] Part Code

[2] Dies in series quantity

[3] Dies in parallel quantity

[4] Correlated color temperature

[5] Chromaticity range

[6] CRI

1/11

DATA SHEET

CLL 040 - 12 18 A1 - 50 K L1 A1

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

CITILED

Name CLL040-1218A1-50KL1A1

[1]

[2]

[3]

[4]

[5]

[6]

< Features >

- External Dimensions: 28.0×28.0×1.4 mm

- Internal Structure: Aluminum Base Chip on Board

- Connection to Heat Sink: By M3 screw (Recommended)

- Luminous Flux: 5070 lm @ 1080 mA

- CCT: 5000 K

- CRI: Ra 65 typ.

- Thermal Resistance: 0.6 C/W

- RoHS Compliant

Ref.CE-P1996 02/12 R1(0612)

3. Outline drawing - Marking

CRI : Ra 65 Typ.

Correlated color temperature : 5000K

Dies in parallel quantity : 18

Dies in series quantity : 12

4. Performance

(1) Absolute Maximum Rating

*1 Input power and forward current are the values when the LED is used within the range of

the derating curve in this data sheet.

*2 Refer to 3. Outline drawing for Tc measurement point

*3 D.C. Current : Tj = Tc + Rj-c X Pi

Rating Value

Unit

Input Power Pi

Parameter

Symbol

Forward Current

F2160

96.2 W

2/11

Junction Temperature

Storage Temperature

-40 ~ +100

Operating Temperature

-30 ~ +85

DATA SHEET

150

Case Temperature Tc 100

Reverse Current

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

CITILED

Name CLL040-1218A1-50KL1A1

Unit : mm

Tolerances unless otherwise specified : +/-0.3

Marking 1 : Serial No.

Marking 2 : 12 18 50 L1

Anode

(Tc Measurement Point)

Marking 2

Marking 1

Cathode

Ref.CE-P1996 02/12 R1(0612)

(2) Electro-optical Characteristics

Tc=25C

Chromaticity coordinates ( Condition : IF=1080mA, Tc = 25C)

Note: The tolerance of measurement at our tester is V

+/-3% , Φv+/-10% , Chromaticity(x,y)+/-0.005 and Ra+/-1.

DATA SHEET 3/11

Forward Voltage

Symbol

=1080mA

33.6

F36.6

Parameter Condition Min. Typ.

39.9 V

Max Unit

5070

=1080mA

4310

Luminous Flux

CRI

Φv

=1080mA

0.6

C/W

Thermal Resistance

Rj-c

Junction-Case

65 - -

CITILED

Name CLL040-1218A1-50KL1A1

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

x y

Center 0.3473 0.3717

a 0.3572 0.3919

b 0.3397 0.3775

c 0.3387 0.3528

d 0.3536 0.3646

0.36

0.38

x-y chart-CIE1931

0.34

0.35

0.36

0.37

0.38

0.39

0.40

0.32 0.33 0.34 0.35 0.36 0.37

Color region

B.B. Locus

4800K

5400K 5000K 4600K

5200K

Ref.CE-P1996 02/12 R1(0612)

5. Characteristics

Forward Current vs. Forward Voltage Forward Current vs. Relative Luminous Flux

Tc=25C Tc=25C

Forward Current vs. Chromaticity Coordinate Case Temperature vs. Chromaticity Coordinate

Tc=25C

=1080mA

4/11

DATA SHEET

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

CITILED

Name CLL040-1218A1-50KL1A1

30.0

32.0

34.0

36.0

38.0

40.0

42.0

0 500 1000 1500 2000 2500

IF [mA]

[V]

20%

40%

60%

80%

100%

120%

140%

160%

180%

200%

0 500 1000 1500 2000 2500

IF [mA]

Relative Luminous Flux [a.u.]

-0.020

-0.015

-0.010

-0.005

0.000

0.005

0.010

0.015

0.020

0 500 1000 1500 2000 2500

IF [mA]

△

Δｘ

Δｙ

-0.020

-0.015

-0.010

-0.005

0.000

0.005

0.010

0.015

0.020

0 25 50 75 100

Tc [C]

△

Δx

Δy

Ref.CE-P1996 02/12 R1(0612)

Case Temperature vs. Forward Voltage Case Temperature vs. Relative Luminous Flux

=1080mA

Case Temperature vs. Allowable Forward Current Spectrum

Tc=25C I

=1080mA

Directive Characteristic

CITIZEN ELECTRONICS CO.,LTD. JAPAN

DATA SHEET 5/11

Symbol

CITILED

Name CLL040-1218A1-50KL1A1

33.0

34.0

35.0

36.0

37.0

38.0

39.0

0 25 50 75 100

Tc [C]

[V]

20%

40%

60%

80%

100%

120%

0 25 50 75 100

Tc [C]

Relative Luminous Flux [a.u.]

500

1000

1500

2000

2500

0 25 50 75 100 125

Tc [C]

[mA]

20%

40%

60%

80%

100%

120%

350 450 550 650 750 850

λ [nm]

Relative Emission Intensity [a.u.]

20%

40%

60%

80%

100%

80°

70°

60°

50°

40°30°

20°10°

-80°

-70°

-60°

-50°

-20°-30°

-40° -10°

90°

-90°

X direction

Y direction

Ref.CE-P1996 02/12 R1(0612)

6. Reliability

（１）

Datails of the tests

(2)Judgement Criteria of Failure for Reliability Test

(Ta=25C)

U defines the upper limit of the specified characteristics. S defines the initial value.

Note : Measurement shall be taken between 2 hours and 24 hours, and the test pieces should be

return to the normal ambient conditions after the completion of each test.

Ta=25 C, I

=1080mA× 1000 hours(with Al-fin)

=1080 mA Tjmax=150C

1000 hours(with Al-fin)

-40 C × 1000 hours

100 C × 1000 hours

Test Item

Test Condition

Symbol

Measuring Condition

Judgement Criteria for Failure

Measuring Item

Continuous Operation Test

Low Temperature Storage Test

High Temperature Storage Test

Moisture-proof Test

Thermal Shock Test

=1080mA

φv

CITIZEN ELECTRONICS CO.,LTD. JAPAN

DATA SHEET

>U X 1.1

<S X 0.85

=1080mA

Forward Voltage

Total Luminous Flux

85 C, 85 %RH for 500 hours

6/11

-40 C × 30 minutes – 100 C × 30 minutes, 100 cycle

Symbol

CITILED

Name CLL040-1218A1-50KL1A1

Ref.CE-P1996 02/12 R1(0612)

7. Packing Specifications

(1) Packing

An empty tray is placed on top of a six-tier tray which contain 30 pieces each. The set of seven

trays is banded together with two rubber bands.

(Smallest packing unit: 180 pieces)

A label with product name, quantity, lot number is placed on the upper empty tray.

Tray (Dimensions: 310 × 210 × 12 mm / Materials: Electrically conductive PS)

< Example of indication label > 1. TYPE e.g. CLL040-1218A1-50KL1A1

2. P.No. (Cutomer's P/N) e.g. 50008-010-1203303M1

3. Lot No.

- First and second letter: Last digit of the year e.g. 11 : year 2011

- Third letter: Production month e.g. 8 : August

Note: October, November and December are designated

- Forth letter: CE's control number e.g. 5035

4. Quantity

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

DATA SHEET 7/11

CITILED

Name CLL040-1218A1-50KL1A1

Product 30 pcs/tray

< Packing figure >

CUSTOMER

PASS

CITIZEN ELECTRONICS

TYPE

P. NO

Lot No

Q'ty

: CLL0

0-******-*******

: ******

: *******

: ***

---(1)

---(2)

---(3)

---(4)

Ref.CE-P1996 02/12 R1(0612)

．

Precautions

DATA SHEET 8/11

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

CITILED

Name CLL040-1218A1-50KL1A1

Thermal

Interface

materials

(Insulation)

Outer heart sink

Spring Washer (

=< Φ

)

M3screw

Plane washer (

=< Φ6mm

)

(1) 1. Handling with care for this product

-Both the light emitting area and white dam over the light emitting area is composed of resin

materials.

Please avoid the resin area from being pressed, stressed, rubbed, come into contact with sharp

metal nail

(e.g. edge of reflector part) because the function, performance and reliability of this product

are negatively impacted.

(2) Countermeasure against static electricity

-Handling of this product needs countermeasures against static electricity

because this is a semiconductor product.

-Please take adequate measures to prevent any static electricity being produced

such as the wearing of a wristband or anti-static gloves when handling this product.

-Every manufacturing facility in regard to the product (plant, equipment, machine, carrier machine

and conveyance unit) should be connected to ground and please avoid the product to be electric-charged.

-ESD sensitivity of this product is over 1000V (HBM, based on JEITA ED-4701/304).

-After assembling the LEDs into your final product(s), it is recommended to check

whether the assembled LEDs are damaged by static electricity (electrical leak phenomenon) or not.

-It is easy to find static damaged LED dies by a light-on test with the minimum current value.

(3) Caution of product assembly

-Regarding this product assembling on the heat sink, it is recommended to use M3 screw.

It might be good for screw tightening on the heat sink to do temporary tightening and final tightening.

In addition, please don’t press with excess stress on the product.

-The condition of the product assembling on the heat sink and the control of screw tightening torque

needs to be optimized according to the specification of the heat sink.

-Roughness, unevenness and burr of surface negatively impact thermal bonding

between the product and heat sink and increase heat thermal resistance between them.

Confidence of thermally and mechanical coupling between the product and heat sink are confirmed

by checking the mounting surface and measuring the case temperature of the product.

-In order to reduce the thermal resistance at assembly, it might be good to use

TIM (Thermal Interface Material) on whole contact surface of the product.

In case of using thermal grease for the TIM, it might be good to be applied uniformly

on the contact surface of the product. In case of using thermal sheet for the TIM,

it might be good to make sure that the product is NOT strained by stress

when the screws are tightened for assembly.

Resin portion (including white resin)

Recommended installation screw pitch

22.8

Ref.CE-P1996 02/12 R1(0612)

8. Precautions (continued)

CITIZEN ELECTRONICS CO.,LTD. JAPAN

DATA SHEET 9/11

Symbol

CITILED

Name CLL040-1218A1-50KL1A1

(4) Thermal Design

-The thermal design to draw heat away from the LED junction is most critical parameter

for an LED illumination system. High operating temperatures at the LED junction adversely affect

the performance of LED’s light output and lifetime. Therefore the LED junction temperature should

not exceed the absolute maximum rating in LED illumination system.

(Note : Refer to 4-(1) Performance)

-The LED junction temperature while operation of LED illumination system depends upon

thermal resistance of internal LED package (Rj-c), outer thermal resistances of LED package,

power loss and ambient temperature. Please take both of the thermal design specifications

and ambient temperature conditions into consideration for the setting of driving conditions.

-For more information, please refer to application note "Thermal Management CLL040 Series".

(5) Driving Current

-A constant current is recommended as an applying driving current to this product.

In the case of constant voltage driving, please connect current-limiting resistor to each products in series

and control the driving current to keep under the absolute maximum rating forward current value.

-Electrical transient might apply excess voltage, excess current and reverse voltage to the product(s).

They also affect negative impact on the product(s) therefore please make sure that no excess voltage,

excess current and reverse voltage is applied to the product(s)

when the LED driver is turn-on and/or turn-off.

-For more information, please refer to application note "Driving".

(6) Lighting at a minimum current value

- The minimum current value of all LED dice lighting is 90 mA.

(The minimum current of each product is calculated and stated on the premise of 5mA dice)

-In a case where the lowest current is applied to the product,

some of LED dice in the product might look different in their brightness

due to the individual difference of the LED dice, and they are not failed.

(7) Electrical Safety

-This product is designed and produced according to IEC 62031:2008

(IEC 62031:2008 LED modules for general lighting. Safety specification)

-Dielectric voltage withstand test has been conducted on this product to see any failure

after applying voltage between active pads and aluminum section of the product,

and to pass at least 500V.

-Considering conformity assessment for IEC62031:2008, almost all items of the specification

depend upon your final product of LED illumination system.

Therefore, please confirm with your final product for electrical safety of your product.

As well, the products comply with the criteria of IEC62031:2008 as single LED package.

Ref.CE-P1996 02/12 R1(0612)

8. Precautions (continued)

CITIZEN ELECTRONICS CO.,LTD. JAPAN

Symbol

CITILED

DATA SHEET 10/11

Name CLL040-1218A1-50KL1A1

(9) Eye Safety

-The International Electrical Commission (IEC) published in 2006 IEC 62471

”2006 Photobiological safety of lamps and lamp systems ” which includes LEDs within its scope.

When sorting single LEDs according to IEC 62471, almost all white LEDs can be classified

as belonging to either Exempt Group (no hazard) or Risk Group 1 (low risk).

-However, Optical characteristics of LEDs such as radiant flux,

spectrum and light distribution are factors that affect the risk group determination of the LED,

and especially a high-power LED, that emits light containing blue wavelengths,

might have properties equivalent to those of Risk Group 2 (moderate risk).

-Great care should be taken when directly viewing an LED that is driven at high current,

has multiple uses as a module or when focusing the light with optical instruments,

as these actions might greatly increase the hazard to your eyes.

-It is recommended to regard the evaluation of stand-alone LED packages as a reference

and to evaluate your final product.

(10) This product is not designed for usage under the following conditions.

If the product might be used under the following conditions, you shall evaluate its effect

and appropriate them. In places where the product might:

-directly and indirectly get wet due to rain and/or at place with the fear.

-be damage by seawater and/or at place with the fear

-be exposed to corrosive gas (such as Cl2, H2S, NH3, SOx, NOx and so on) and/or at place with the fear.

-be exposed to dust, fluid or oil and/or at place with the fear.

(8) Recommended soldering Condition (This product is not adaptable to reflow process.)

-For manual soldering

Please use lead-free soldering.

Soldering shall be implemented using a soldering bit at a temperature lower than 350C°,

and shall be finished within 3.5 seconds for one land.

No external force shall be applied to resin part while soldering is implemented.

Next process of soldering should be carried out after the product has return to ambient temperature.

-For soldering correction

Regarding soldering correction, above conditions shall be applied.

Contacts number of soldering bit should be within twice for each terminal as a correction.

* Citizen Electronics cannot guarantee if usage exceeds these recommended conditions.

Please use it after sufficient verification is carried out on your own risk if absolutely necessary.

Ref.CE-P1996 02/12 R1(0612)

9. Precautions with regard to product use

(1) This document is provided for reference purposes only so that CITIZEN ELECTRONICS'

products are used as intended. CITIZEN ELECTRONICS neither makes warranties or

representations with respect to the accuracy or completeness of the information contained

in this document nor grants any license to any intellectual property rights or any other

rights of CITIZEN ELECTRONICS or any third party with respect to the information

in this document.

(2) All information included in this document such as product data, diagrams, charts,

is current as of the date this document is issued.

Such information, however, is subject to change without any prior notice.

Before purchasing or using any CITIZEN ELECTRONICS' products listed in this document,

please confirm the latest product information with a CITIZEN ELECTRONICS' sales office,

and formal specifications must be exchanged and signed by both parties prior to mass production.

(3) CITIZEN ELECTRONICS has used reasonable care in compiling the information

included in this document,

but CITIZEN ELECTRONICS assumes no liability whatsoever for any damages incurred as

a result of errors or omissions in the information included in this document.

(4) Absent ａ written signed agreement, except as provided in the relevant terms and conditions of

sale for product, and to the maximum extent allowable by law, CITIZEN ELECTRONICS

assumes no liability whatsoever, including without limitation, indirect, consequential, special,

or incidental damages or loss, including without limitation, loss of profits, loss of opportunities,

business interruption and loss of data, and disclaims any and all express or implied warranties

and conditions related to sale, use of product, or information, including warranties

or conditions of merchantability, fitness for a particular purpose, accuracy of information,

or no infringement.

(5) Though CITIZEN ELECTRONICS works continually to improve products' quality and reliability,

products can malfunction or fail. Customers are responsible for complying with safety standards

and for providing adequate designs and safeguards to minimize risk and avoid situations

in which a malfunction or failure of a product could cause loss of human life,

bodily injury or damage to property, including data loss or corruption.

In addition, customers are also responsible for determining the appropriateness of

use of any information contained in this document such as application cases not only with

evaluating by their own but also by the entire system.

CITIZEN ELECTRONICS assumes no liability for customers' product design or applications.

(6) Please contact CITIZEN ELECTRONICS' sales office if you have any questions regarding

the information contained in this document, or if you have any other inquiries.

CITIZEN Micro HumanTech is a registered trademark of Citizen Holding Co., Japan.

CITILED is a registered trademark of CITIZEN ELECTRONICS CO., LTD. Japan

CITIZEN ELECTRONICS CO.,LTD. JAPAN

DATA SHEET 11/11

Symbol

CITILED

Name CLL040-1218A1-50KL1A1

Ref.CE-P1996 02/12 R1(0612)