Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) 2M x 18, 1M x 36, 512K x 72 36Mb Sync NBT SRAMs 119- and 209-Pin BGA Commercial Temp Industrial Temp Features * NBT (No Bus Turn Around) functionality allows zero wait Read-Write-Read bus utilization; fully pin-compatible with both pipelined and flow through NtRAMTM, NoBLTM and ZBTTM SRAMs * FT pin for user-configurable flow through or pipeline operation * IEEE 1149.1 JTAG-compatible Boundary Scan * ZQ mode pin for user-selectable high/low output drive * 2.5 V or 3.3 V +10%/-5% core power supply * 2.5 V or 3.3 V I/O supply * LBO pin for Linear or Interleaved Burst mode * Byte Write (BW) and/or Global Write (GW) operation * Internal self-timed write cycle * Automatic power-down for portable applications * JEDEC-standard 119- and 209-bump BGA package Pipeline 3-1-1-1 3.3 V 2.5 V Flow Through 2-1-1-1 3.3 V 2.5 V tKQ tCycle Curr (x18) Curr (x36) Curr (x72) Curr (x18) Curr (x36) Curr (x72) -250 -225 -200 -166 -150 -133 Unit 2.3 2.5 3.0 3.5 3.8 4.0 ns 4.0 4.4 5.0 6.0 6.6 7.5 ns 250 MHz-133MHz 2.5 V or 3.3 V VDD 2.5 V or 3.3 V I/O with either ADSP or ADSC inputs. In Burst mode, subsequent burst addresses are generated internally and are controlled by ADV. The burst address counter may be configured to count in either linear or interleave order with the Linear Burst Order (LBO) input. The Burst function need not be used. New addresses can be loaded on every cycle with no degradation of chip performance. Flow Through/Pipeline Reads The function of the Data Output register can be controlled by the user via the FT mode . Holding the FT mode pin low places the RAM in Flow Through mode, causing output data to bypass the Data Output Register. Holding FT high places the RAM in Pipeline mode, activating the rising-edge-triggered Data Output Register. Byte Write and Global Write Byte write operation is performed by using Byte Write enable (BW) input combined with one or more individual byte write signals (Bx). In addition, Global Write (GW) is available for writing all bytes at one time, regardless of the Byte Write control inputs. 365 560 660 360 550 640 335 510 600 330 500 590 305 460 540 305 460 530 265 400 460 260 390 450 245 370 430 240 360 420 215 330 380 215 330 370 mA mA mA mA mA mA tKQ tCycle 6.0 7.0 6.5 7.5 7.5 8.5 8.5 10 10 10 11 15 ns ns Low power (Sleep mode) is attained through the assertion (High) of the ZZ signal, or by stopping the clock (CK). Memory data is retained during Sleep mode. Curr (x18) Curr (x36) Curr (x72) Curr (x18) Curr (x36) Curr (x72) 235 300 350 235 300 340 230 300 350 230 300 340 210 270 300 210 270 300 200 270 300 200 270 300 195 270 300 195 270 300 150 200 220 145 190 220 mA mA mA mA mA mA Core and Interface Voltages FLXDriveTM The ZQ pin allows selection between high drive strength (ZQ low) for multi-drop bus applications and normal drive strength (ZQ floating or high) point-to-point applications. See the Output Driver Characteristics chart for details. Sleep Mode The GS8324Z18/36/72 operates on a 2.5 V or 3.3 V power supply. All input are 3.3 V and 2.5 V compatible. Separate output power (VDDQ) pins are used to decouple output noise from the internal circuits and are 3.3 V and 2.5 V compatible. Functional Description Applications The GS8324Z18/36/72 is a 37,748,736-bit high performance 2-die synchronous SRAM module with a 2-bit burst address counter. Although of a type originally developed for Level 2 Cache applications supporting high performance CPUs, the device now finds application in synchronous SRAM applications, ranging from DSP main store to networking chip set support. Controls Addresses, data I/Os, chip enable (E1), address burst control inputs (ADSP, ADSC, ADV), and write control inputs (Bx, BW, GW) are synchronous and are controlled by a positive-edgetriggered clock input (CK). Output enable (G) and power down control (ZZ) are asynchronous inputs. Burst cycles can be initiated Rev: 1.00 10/2001 1/46 (c) 2001, Giga Semiconductor, Inc. Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. NoBL is a trademark of Cypress Semiconductor Corp.. NtRAM is a trademark of Samsung Electronics Co.. ZBT is a trademark of Integrated Device Technology, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z72B Pad Out 209-Bump BGA--Top View 1 2 3 4 5 6 7 8 9 10 11 A DQG5 DQG1 A13 E2 A14 ADV A15 E3 A17 DQB1 DQB5 A B DQG6 DQG2 BC BG NC W A16 BB BF DQB2 DQB6 B C DQG7 DQG3 BH BD NC E1 NC BE BA DQB3 DQB7 C D DQG8 DQG4 VSS NC NC G NC NC VSS DQB4 DQB8 D E DQPG9 DQPC9 VDDQ VDDQ VDD VDD VDD VDDQ VDDQ DQPF9 DQPB9 E F DQC4 DQC8 VSS VSS VSS ZQ VSS VSS VSS DQF8 DQF4 F G DQC3 DQC7 VDDQ VDDQ VDD MCH VDD VDDQ VDDQ DQF7 DQF3 G H DQC2 DQC6 VSS VSS VSS MCL VSS VSS VSS DQF6 DQF2 H J DQC1 DQC5 VDDQ VDDQ VDD MCH VDD VDDQ VDDQ DQF5 DQF1 J K NC NC CK NC VSS MCL VSS NC NC NC NC K L DQH1 DQH5 VDDQ VDDQ VDD FT VDD VDDQ VDDQ DQA5 DQA1 L M DQH2 DQH6 VSS VSS VSS MCL VSS VSS VSS DQA6 DQA2 M N DQH3 DQH7 VDDQ VDDQ VDD MCH VDD VDDQ VDDQ DQA7 DQA3 N P DQH4 DQH8 VSS VSS VSS ZZ VSS VSS VSS DQA8 DQA4 P R DQPD9 DQPH9 VDDQ VDDQ VDD VDD VDD VDDQ VDDQ DQPA9 DQPE9 R T DQD8 DQD4 VSS NC NC LBO PE NC VSS DQE4 DQE8 T U DQD7 DQD3 NC A12 NC A11 A18 A10 NC DQE3 DQE7 U V DQD6 DQD2 A9 A8 A7 A1 A6 A5 A4 DQE2 DQE6 V W DQD5 DQD1 TMS TDI A3 A0 A2 TDO TCK DQE1 DQE5 W 11 x 19 Bump BGA--14 x 22 mm2 Body--1 mm Bump Pitch Rev: 1.00 10/2001 2/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z36C Pad Out 209-Bump BGA--Top View 1 2 3 4 5 6 7 8 9 10 11 A NC NC A13 E2 A14 ADV A15 E3 A17 DQB1 DQB5 A B NC NC BC NC A19 W A16 BB NC DQB2 DQB6 B C NC NC NC BD NC E1 NC NC BA DQB3 DQB7 C D NC NC VSS NC NC G NC NC VSS DQB4 DQB8 D E NC DQPC9 VDDQ VDDQ VDD VDD VDD VDDQ VDDQ NC DQPB9 E F DQC4 DQC8 VSS VSS VSS ZQ VSS VSS VSS NC NC F G DQC3 DQC7 VDDQ VDDQ VDD MCH VDD VDDQ VDDQ NC NC G H DQC2 DQC6 VSS VSS VSS MCL VSS VSS VSS NC NC H J DQC1 DQC5 VDDQ VDDQ VDD MCH VDD VDDQ VDDQ NC NC J K NC NC CK NC VSS MCL VSS NC NC NC NC K L NC NC VDDQ VDDQ VDD FT VDD VDDQ VDDQ DQA5 DQA1 L M NC NC VSS VSS VSS MCL VSS VSS VSS DQA6 DQA2 M N NC NC VDDQ VDDQ VDD MCH VDD VDDQ VDDQ DQA7 DQA3 N P NC NC VSS VSS VSS ZZ VSS VSS VSS DQA8 DQA4 P R DQPD9 NC VDDQ VDDQ VDD VDD VDD VDDQ VDDQ DQPA9 NC R T DQD8 DQD4 VSS NC NC LBO PE NC VSS NC NC T U DQD7 DQD3 NC A12 NC A11 A18 A10 NC NC NC U V DQD6 DQD2 A9 A8 A7 A1 A6 A5 A4 NC NC V W DQD5 DQD1 TMS TDI A3 A0 A2 TDO TCK NC NC W 11 x 19 Bump BGA--14 x 22 mm2 Body--1 mm Bump Pitch Rev: 1.00 10/2001 3/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z18C Pad Out 209-Bump BGA--Top View 1 2 3 4 5 6 7 8 9 10 11 A NC NC A13 VDD A14 ADV A15 VSS A17 NC NC A B NC NC BB NC A19 W A16 NC NC NC NC B C NC NC NC NC NC E1 A20 NC BA NC NC C D NC NC VSS NC NC G NC NC VSS NC NC D E NC DQPB9 VDDQ VDDQ VDD VDD VDD VDDQ VDDQ NC NC E F DQB4 DQB8 VSS VSS VSS ZQ VSS VSS VSS NC NC F G DQB3 DQB7 VDDQ VDDQ VDD MCH VDD VDDQ VDDQ NC NC G H DQB2 DQB6 VSS VSS VSS MCL VSS VSS VSS NC NC H J DQB1 DQB5 VDDQ VDDQ VDD MCH VDD VDDQ VDDQ NC NC J K NC NC CK NC VSS MCL VSS NC NC NC NC K L NC NC VDDQ VDDQ VDD FT VDD VDDQ VDDQ DQA5 DQA1 L M NC NC VSS VSS VSS MCL VSS VSS VSS DQA6 DQA2 M N NC NC VDDQ VDDQ VDD VDD VDD VDDQ VDDQ DQA7 DQA3 N P NC NC VSS VSS VSS ZZ VSS VSS VSS DQA8 DQA4 P R NC NC VDDQ VDDQ VDD VDD VDD VDDQ VDDQ DQPA9 NC R T NC NC VSS NC NC LBO PE NC VSS NC NC T U NC NC NC A12 NC A11 A18 A10 NC NC NC U V NC NC A9 A8 A7 A1 A6 A5 A4 NC NC V W NC NC TMS TDI A3 A0 A2 TDO TCK NC NC W 11 x 19 Bump BGA--14 x 22 mm2 Body--1 mm Bump Pitch Rev: 1.00 10/2001 4/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z18/36/72 209-Bump BGA Pin Description Pin Location Symbol Type Description W6, V6 A0, A1 I Address field LSBs and Address Counter Preset Inputs. W7, W5, V9, V8, V7, V5, V4, V3, U8, U6, U4, A3, A5, A7, B7, A9, U7 An I Address Inputs B5 A19 I Address Inputs (x36/x18 Versions) C7 A20 I Address Inputs (x18 Version) L11, M11, N11, P11, L10, M10, N10, P10, R10 A10, B10, C10, D10, A11, B11, C11, D11, E11 J1, H1, G1, F1, J2, H2, G2, F2, E2 W2, V2, U2, T2, W1, V1, U1, T1, R1 W10, V10, U10, T10, W11, V11, U11, T11, R11 J11, H11, G11, F11, J10, H10, G10, F10, E10 A2, B2, C2, D2, A1, B1, C1, D1, E1 L1, M1, N1, P1, L2, M2, N2, P2, R2 DQA1-DQA9 DQB1-DQB9 DQC1-DQC9 DQD1-DQD9 DQE1-DQE9 DQF1-DQF9 DQG1-DQG9 DQH1-DQH9 I/O Data Input and Output pins (x72 Version) L11, M11, N11, P11, L10, M10, N10, P10, R10 A10, B10, C10, D10, A11, B11, C11, D11, E11 J1, H1, G1, F1, J2, H2, G2, F2, E2 W2, V2, U2, T2, W1, V1, U1, T1, R1 DQA1-DQA9 DQB1-DQB9 DQC1-DQC9 DQD1-DQD9 I/O Data Input and Output pins (x36 Version) L11, M11, N11, P11, L10, M10, N10, P10, R10 J1, H1, G1, F1, J2, H2, G2, F2, E2 DQA1-DQA9 DQB1-DQB9 I/O Data Input and Output pins (x18 Version) C9, B8 BA, BB I Byte Write Enable for DQA, DQB I/Os; active low B3, C4 BC,BD I Byte Write Enable for DQC, DQD I/Os; active low (x72/x36 Versions) C8, B9, B4, C3 BE, BF, BG,BH I Byte Write Enable for DQE, DQF, DQG, DQH I/Os; active low (x72 Version) B5 NC -- No Connect (x72 Version) C7 NC -- No Connect (x72/x36 Versions) W10, V10, U10, T10, W11, V11, U11, T11, R11 J11, H11, G11, F11, J10, H10, G10, F10, E10 A2, B2, C2, D2, A1, B1, C1, D1, E1 L1, M1, N1, P1, L2, M2, N2, P2, R2, C8, B9, B4, C3 NC -- No Connect (x36/x18 Versions) B3, C4 NC -- No Connect (x18 Version) C5, D4, D5, D7, D8, K1, K2, K4, K8, K9, K10, K11, T4, T5, T7, T8, U3, U5, U9 NC -- No Connect K3 CK I Clock Input Signal; active high C6 E1 I Chip Enable; active low A8 E3 I Chip Enable; active low (x72/x36 Versions) A4 E2 I Chip Enable; active high (x72/x36 Versions) D6 G I Output Enable; active low A6 ADV I Burst address counter advance enable Rev: 1.00 10/2001 5/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z18/36/72 209-Bump BGA Pin Description Pin Location Symbol Type Description P6 ZZ I Sleep Mode control; active high L6 FT I Flow Through or Pipeline mode; active low T6 LBO I Linear Burst Order mode; active low G6, J6 MCH I Must Connect High N6 MCH I Must Connect High (x72 and x36 versions) H6, J6, K6, M6 MCL Must Connect Low A8, N6 MCL Must Connect Low (x18 version) B6 W I Write Enable; active low T7 PE I Parity Bit Enable; active low (High = x16/32 Mode, Low = x18/36 Mode) F6 ZQ I FLXDrive Output Impedance Control (Low = Low Impedance [High Drive], High = High Impedance [Low Drive]) W3 TMS I Scan Test Mode Select W4 TDI I Scan Test Data In W8 TDO O Scan Test Data Out W9 TCK I Scan Test Clock A4, N6 VDD I Core power supply (x18 version) E5, E6, E7, G5, G7, J5, J7, L5, L7, N5, N7, R5, R6, R7 VDD I Core power supply D3, D9, F3, F4, F5, F7, F8, F9, H3, H4, H5, H7, H8, H9, K5, K7, M3, M4, M5, M7, M8, M9, P3, P4, P5, P7, P8, P9, T3, T9 VSS I I/O and Core Ground E3, E4, E8, E9, G3, G4, G8, G9, J3, J4, J8, J9, L3, L4, L8, L9, N3, N4, N8, N9, R3, R4, R8, R9 VDDQ I Output driver power supply Rev: 1.00 10/2001 6/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z36B Pad Out 119-Bump BGA--Top View 1 2 3 4 5 6 7 A VDDQ A6 A7 A18 A8 A9 VDDQ A B NC E2 A4 ADV A15 E3 NC B C NC A5 A3 VDD A14 A16 NC C D DQC DQPC VSS ZQ VSS DQPB DQB D E DQC DQC VSS E1 VSS DQB DQB E F VDDQ DQC VSS G VSS DQB VDDQ F G DQC DQC BC A17 BB DQB DQB G H DQC DQC VSS W VSS DQB DQB H J VDDQ VDD NC VDD NC VDD VDDQ J K DQD DQD VSS CK VSS DQA DQA K L DQD DQD BD NC BA DQA DQA L M VDDQ DQD VSS CKE VSS DQA VDDQ M N DQD DQD VSS A1 VSS DQA DQA N P DQD DQPD VSS A0 VSS DQPA DQA P R NC A2 LBO VDD FT A13 PE R T NC NC A10 A11 A12 A19 ZZ T U VDDQ TMS TDI TCK TDO NC VDDQ U 7 x 17 Bump BGA--14 x 22 mm2 Body--1.27 mm Bump Pitch Rev: 1.00 10/2001 7/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z18B Pad Out 119-Bump BGA--Top View 1 2 3 4 5 6 7 A VDDQ A6 A7 A18 A8 A9 VDDQ A B NC VDD A4 ADV A15 VSS NC B C NC A5 A3 VDD A14 A16 NC C D DQB NC VSS ZQ VSS DQPA NC D E NC DQB VSS E1 VSS NC DQA E F VDDQ NC VSS G VSS DQA VDDQ F G NC DQB BB A17 NC NC DQA G H DQB NC VSS W VSS DQA NC H J VDDQ VDD NC VDD NC VDD VDDQ J K NC DQB VSS CK VSS NC DQA K L DQB NC NC VDD BA DQA NC L M VDDQ DQB VSS CKE VSS NC VDDQ M N DQB NC VSS A1 VSS DQA NC N P NC DQPB VSS A0 VSS NC DQA P R NC A2 LBO VDD FT A13 PE R T NC A10 A11 A20 A12 A19 ZZ T U VDDQ TMS TDI TCK TDO NC VDDQ U 7 x 17 Bump BGA--14 x 22 mm2 Body--1.27 mm Bump Pitch Rev: 1.00 10/2001 8/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z18/36 119-Bump BGA Pin Description Pin Location Symbol Type Description P4, N4 A0, A1 I Address field LSBs and Address Counter Preset Inputs R2, C3, B3, C2, A2, A3, A5, A6, T3, T5, R6, C5, B5, C6, G4, A4 An I Address Inputs T4, T6 An T2 NC -- No Connect (x36 Version) T2, T6, T4 An I Address Input (x18 Version) K7, L7, N7, P7, K6, L6, M6, N6 H7, G7, E7, D7, H6, G6, F6, E6 H1, G1, E1, D1, H2, G2, F2, E2 K1, L1, N1, P1, K2, L2, M2, N2 DQA1-DQA8 DQB1-DQB8 DQC1-DQC8 DQD1-DQD8 I/O Data Input and Output pins. (x36 Version) P6, D6, D2, P2 DQA9, DQB9, DQC9, DQD9 I/O Data Input and Output pins. (x36 Version) L5, G5, G3, L3 BA, BB, BC, BD I Byte Write Enable for DQA, DQB, DQC, DQD I/Os; active low (x36 Version) P7, N6, L6, K7, H6, G7, F6, E7, D6 D1, E2, G2, H1, K2, L1, M2, N1, P2 DQA1-DQA9 DQB1-DQB9 I/O Data Input and Output pins (x18 Version) L5, G3 BA, BB I Byte Write Enable for DQA, DQB I/Os; active low (x18 Version) B1, C1, R1, T1, U6, B7, C7, J3, J5 NC -- No Connect P6, N7, M6, L7, K6, H7, G6, E6, D7, D2, E1, F2, G1, H2, K1, L2, N2, P1, G5, L3 NC -- No Connect (x18 Version) L4 NC -- No Connect (x36 Version) K4 CK I Clock Input Signal; active high M4 CKE I Clock Enable; active low H4 W I Write Enable; active low E4 E1 I Chip Enable; active low B6 E3 I Chip Enable; active low (x36 version) B2 E2 I Chip Enable; active high (x36 version) F4 G I Output Enable; active low B4 ADV I Burst address counter advance enable T7 ZZ I Sleep mode control; active high R5 FT I Flow Through or Pipeline mode; active low R3 LBO I Linear Burst Order mode; active low D4 ZQ I FLXDrive Output Impedance Control (Low = Low Impedance [High Drive], High = High Impedance [Low Drive]) R7 PE I Parity Bit Enable; active low U2 TMS I Scan Test Mode Select U3 TDI I Scan Test Data In Rev: 1.00 10/2001 Address Input (x36 Version) 9/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z18/36 119-Bump BGA Pin Description Pin Location Symbol Type Description U5 TDO O Scan Test Data Out U4 TCK I Scan Test Clock J2, C4, J4, R4, J6 VDD I Core power supply B2, L4 VDD I Core power supply (x18 version) D3, E3, F3, H3, K3, M3, N3, P3, D5, E5, F5, H5, K5, M5, N5, P5 VSS I I/O and Core Ground B6 VSS I I/O and Core Ground (x18 version) A1, F1, J1, M1, U1, A7, F7, J7, M7, U7 VDDQ I Output driver power supply Rev: 1.00 10/2001 10/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z18/36/72 Block Diagram Register A0-An D Q A0 A0 D0 Q0 A1 A1 D1 Q1 Counter Load A LBO ADV Memory Array CK ADSC ADSP Q D Register GW BW BA D Q 36 36 Register D Q BB 4 Register D Q D Q D Q Register Register D Q Register BC BD Register D 36 Q 36 Register E1 D Q 36 Register D Q FT G ZZ 36 Power Down DQx0-DQx9 Control Note: Only x36 version shown for simplicity. Rev: 1.00 10/2001 11/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z18 Die Layout TDI Inputs Die A x18 16Mb TDO TDI Die B x18 16Mb TDO 18 I/Os GS8324Z36 Die Layout TDI Inputs Die A x18 16Mb TDO TDI 18 I/Os Inputs Die A x36 32Mb TDO TDI 36 I/Os Rev: 1.00 10/2001 TDO 18 I/Os GS8324Z72 Die Layout TDI Die B x18 16Mb Die B x36 32Mb TDO 36 I/Os 12/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Functional Details Clocking Deassertion of the Clock Enable (CKE) input blocks the Clock input from reaching the RAM's internal circuits. It may be used to suspend RAM operations. Failure to observe Clock Enable set-up or hold requirements will result in erratic operation. Pipeline Mode Read and Write Operations All inputs (with the exception of Output Enable, Linear Burst Order and Sleep) are synchronized to rising clock edges. Single cycle read and write operations must be initiated with the Advance/Load pin (ADV) held low, in order to load the new address. Device activation is accomplished by asserting all three of the Chip Enable inputs (E1, E2, and E3). Deassertion of any one of the Enable inputs will deactivate the device. Function W BA BB BC BD Read H X X X X Write Byte "a" L L H H H Write Byte "b" L H L H H Write Byte "c" L H H L H Write Byte "d" L H H H L Write all Bytes L L L L L Write Abort/NOP L H H H H Read operation is initiated when the following conditions are satisfied at the rising edge of clock: CKE is asserted low, all three chip enables (E1, E2, and E3) are active, the write enable input signals W is deasserted high, and ADV is asserted low. The address presented to the address inputs is latched into the address register and presented to the memory core and control logic. The control logic determines that a read access is in progress and allows the requested data to propagate to the input of the output register. At the next rising edge of clock the read data is allowed to propagate through the output register and onto the output pins. Write operation occurs when the RAM is selected, CKE is active, and the Write input is sampled low at the rising edge of clock. The Byte Write Enable inputs (BA, BB, BC, and BD) determine which bytes will be written. All or none may be activated. A write cycle with no Byte Write inputs active is a no-op cycle. The pipelined NBT SRAM provides double late write functionality, matching the write command versus data pipeline length (2 cycles) to the read command versus data pipeline length (2 cycles). At the first rising edge of clock, Enable, Write, Byte Write(s), and Address are registered. The Data In associated with that address is required at the third rising edge of clock. Flow Through Mode Read and Write Operations Operation of the RAM in Flow Through mode is very similar to operations in Pipeline mode. Activation of a Read Cycle and the use of the Burst Address Counter is identical. In Flow Through mode the device may begin driving out new data immediately after new address are clocked into the RAM, rather than holding new data until the following (second) clock edge. Therefore, in Flow Through mode the read pipeline is one cycle shorter than in Pipeline mode. Write operations are initiated in the same way, but differ in that the write pipeline is one cycle shorter as well, preserving the ability to turn the bus from reads to writes without inserting any dead cycles. While the pipelined NBT RAMs implement a double late write protocol in Flow Through mode a single late write protocol mode is observed. Therefore, in Flow Through mode, address and control are registered on the first rising edge of clock and data in is required at the data input pins at the second rising edge of clock. Rev: 1.00 10/2001 13/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Byte Write Truth Table Function GW BW BA BB BC BD Notes Read H H X X X X 1 Read H L H H H H 1 Write byte a H L L H H H 2, 3 Write byte b H L H L H H 2, 3 Write byte c H L H H L H 2, 3, 4 Write byte d H L H H H L 2, 3, 4 Write all bytes H L L L L L 2, 3, 4 Write all bytes L X X X X X Notes: 1. All byte outputs are active in read cycles regardless of the state of Byte Write Enable inputs. 2. Byte Write Enable inputs BA, BB, BC, and/or BD may be used in any combination with BW to write single or multiple bytes. 3. All byte I/Os remain High-Z during all write operations regardless of the state of Byte Write Enable inputs. 4. Bytes "C" and "D" are only available on the x36 version. Rev: 1.00 10/2001 14/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Synchronous Truth Table (x72 and x36 209-Bump BGA) Operation Type Address E1 E2 E3 ZZ ADV W Bx G CKE CK DQ Notes Deselect Cycle, Power Down D None H X X L L X X X L L-H High-Z Deselect Cycle, Power Down D None X X H L L X X X L L-H High-Z Deselect Cycle, Power Down D None X L X L L X X X L L-H High-Z Deselect Cycle, Continue D None X X X L H X X X L L-H High-Z Read Cycle, Begin Burst R External L H L L L H X L L L-H Q Read Cycle, Continue Burst B Next X X X L H X X L L L-H Q 1,10 NOP/Read, Begin Burst R External L H L L L H X H L L-H High-Z 2 Dummy Read, Continue Burst B Next X X X L H X X H L L-H High-Z 1,2,10 Write Cycle, Begin Burst W External L H L L L L L X L L-H D 3 Write Cycle, Continue Burst B Next X X X L H X L X L L-H D 1,3,10 NOP/Write Abort, Begin Burst W None L H L L L L H X L L-H High-Z 2,3 Write Abort, Continue Burst B Next X X X L H X H X L L-H High-Z 1,2,3,10 Current X X X L X X X X H L-H - None X X X H X X X X X X High-Z Clock Edge Ignore, Stall Sleep Mode 1 4 Notes: 1. Continue Burst cycles, whether Read or Write, use the same control inputs. A Deselect continue cycle can only be entered into if a Deselect cycle is executed first. 2. Dummy Read and Write abort can be considered NOPs because the SRAM performs no operation. A Write abort occurs when the W pin is sampled low but no Byte Write pins are active, so no write operation is performed. 3. G can be wired low to minimize the number of control signals provided to the SRAM. Output drivers will automatically turn off during write cycles. 4. If CKE High occurs during a pipelined read cycle, the DQ bus will remain active (Low Z). If CKE High occurs during a write cycle, the bus will remain in High Z. 5. X = Don't Care; H = Logic High; L = Logic Low; Bx = High = All Byte Write signals are high; Bx = Low = One or more Byte/Write signals are Low 6. All inputs, except G and ZZ must meet setup and hold times of rising clock edge. 7. Wait states can be inserted by setting CKE high. 8. This device contains circuitry that ensures all outputs are in High Z during power-up. 9. A 2-bit burst counter is incorporated. 10. The address counter is incriminated for all Burst continue cycles. Rev: 1.00 10/2001 15/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Synchronous Truth Table (x18 209-Bump BGA and x36/x18 119-Bump BGA) Operation Type Address E1 ZZ ADV W Bx G CKE CK DQ Notes Deselect Cycle, Power Down D None H L L X X X L L-H High-Z Deselect Cycle, Power Down D None X L L X X X L L-H High-Z Deselect Cycle, Power Down D None X L L X X X L L-H High-Z Deselect Cycle, Continue D None X L H X X X L L-H High-Z Read Cycle, Begin Burst R External L L L H X L L L-H Q Read Cycle, Continue Burst B Next X L H X X L L L-H Q 1,10 NOP/Read, Begin Burst R External L L L H X H L L-H High-Z 2 Dummy Read, Continue Burst B Next X L H X X H L L-H High-Z 1,2,10 Write Cycle, Begin Burst W External L L L L L X L L-H D 3 Write Cycle, Continue Burst B Next X L H X L X L L-H D 1,3,10 NOP/Write Abort, Begin Burst W None L L L L H X L L-H High-Z 2,3 Write Abort, Continue Burst B Next X L H X H X L L-H High-Z 1,2,3,10 Current X L X X X X H L-H - None X H X X X X X X High-Z Clock Edge Ignore, Stall Sleep Mode 1 4 Notes: 1. Continue Burst cycles, whether Read or Write, use the same control inputs. A Deselect continue cycle can only be entered into if a Deselect cycle is executed first. 2. Dummy Read and Write abort can be considered NOPs because the SRAM performs no operation. A Write abort occurs when the W pin is sampled low but no Byte Write pins are active, so no write operation is performed. 3. G can be wired low to minimize the number of control signals provided to the SRAM. Output drivers will automatically turn off during write cycles. 4. If CKE High occurs during a pipelined read cycle, the DQ bus will remain active (Low Z). If CKE High occurs during a write cycle, the bus will remain in High Z. 5. X = Don't Care; H = Logic High; L = Logic Low; Bx = High = All Byte Write signals are high; Bx = Low = One or more Byte/ Write signals are Low 6. All inputs, except G and ZZ must meet setup and hold times of rising clock edge. 7. Wait states can be inserted by setting CKE high. 8. This device contains circuitry that ensures all outputs are in High Z during power-up. 9. A 2-bit burst counter is incorporated. 10. The address counter is incriminated for all Burst continue cycles. Rev: 1.00 10/2001 16/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Pipelined and Flow Through Read Write Control State Diagram D B Deselect W R D D W New Read New Write R R W B B R W R Burst Read W Burst Write B B D Key D Notes Input Command Code 1. The Hold command (CKE Low) is not shown because it prevents any state change. Transition Current State (n) 2. W, R, B, and D represent input command codes as indicated in the Synchronous Truth Table. Next State (n+1) n n+1 n+2 n+3 Clock (CK) Command Current State Next State Current State and Next State Definition for Pipelined and Flow through Read/Write Control State Diagram Rev: 1.00 10/2001 17/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Pipeline Mode Data I/O State Diagram Intermediate B W R B Intermediate R High Z (Data In) D Data Out (Q Valid) W D Intermediate Intermediate W Intermediate R High Z B D Intermediate Key Notes Input Command Code 1. The Hold command (CKE Low) is not shown because it prevents any state change. Transition Current State (n) Transition Intermediate State (N+1) n Next State (n+2) n+1 2. W, R, B, and D represent input command codes as indicated in the Truth Tables. n+2 n+3 Clock (CK) Command Current State Intermediate State Next State Current State and Next State Definition for Pipeline Mode Data I/O State Diagram Rev: 1.00 10/2001 18/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Flow Through Mode Data I/O State Diagram B W R B R High Z (Data In) Data Out (Q Valid) W D D W R High Z B D Key Notes Input Command Code 1. The Hold command (CKE Low) is not shown because it prevents any state change. Transition Current State (n) 2. W, R, B, and D represent input command codes as indicated in the Truth Tables. Next State (n+1) n n+1 n+2 n+3 Clock (CK) Command Current State Next State Current State and Next State Definition for: Pipeline and Flow Through Read Write Control State Diagram Rev: 1.00 10/2001 19/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Burst Cycles Although NBT RAMs are designed to sustain 100% bus bandwidth by eliminating turnaround cycle when there is transition from read to write, multiple back-to-back reads or writes may also be performed. NBT SRAMs provide an on-chip burst address generator that can be utilized, if desired, to further simplify burst read or write implementations. The ADV control pin, when driven high, commands the SRAM to advance the internal address counter and use the counter generated address to read or write the SRAM. The starting address for the first cycle in a burst cycle series is loaded into the SRAM by driving the ADV pin low, into Load mode. Burst Order The burst address counter wraps around to its initial state after four addresses (the loaded address and three more) have been accessed. The burst sequence is determined by the state of the Linear Burst Order pin (LBO). When this pin is Low, a linear burst sequence is selected. When the RAM is installed with the LBO pin tied high, Interleaved burst sequence is selected. See the tables below for details. Mode Pin Functions Mode Name Pin Name Burst Order Control LBO Output Register Control FT Power Down Control ZZ Parity Enable PE FLXDrive Output Impedance Control ZQ State Function L Linear Burst H Interleaved Burst L Flow Through H or NC Pipeline L or NC Active H Standby, IDD = ISB L or NC Activate 9th I/O's (x18/36 Mode) H Deactivate 9th I/O's (x16/32 Mode) L High Drive (Low Impedance) H or NC Low Drive (High Impedance) Note: There are pull-up devices on the ZQ, SCD DP, and FT pins and a pull-down devices on the PE and ZZ pins, so those input pins can be unconnected and the chip will operate in the default states as specified in the above tables. Enable/Disable Parity I/O Pins This SRAM allows the user to configure the device to operate in Parity I/O active (x18, x36, or x72) or in Parity I/O inactive (x16, x32, or x64) mode. Holding the PE bump low or letting it float will activate the 9th I/O on each byte of the RAM. Grounding PE deactivates the 9th I/O of each byte, although the bit in each byte of the memory array remains active to store and recall parity bits generated and read into the ByteSafe parity circuits. Rev: 1.00 10/2001 20/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) x16/32/64 Mode (PE = 0) Read Parity Error Output Timing Diagram CK Pipelined Mode Flow Through Mode Address A Rev: 1.00 10/2001 DQ Address B Address C Address D Address E Address F D Out A D Out B D Out C D Out D D Out E tKQ tKQX tLZ QE DQ tHZ Err A Err C D Out A D Out B tKQ D Out D tKQX tLZ QE D Out C tHZ Err A 21/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. Err C (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) x18/x36 Mode (PE = 1) Write Parity Error Output Timing Diagram Pipelined Mode Flow Through Mode CK DQ D In A D In B D In C tKQ tHZ Err A DQ D In A D In E tKQX tLZ QE D In D Err C D In B D In C tKQ D In D tKQX tLZ QE D In E tHZ Err A Err C BPR 1999.05.18 Burst Counter Sequences Interleaved Burst Sequence Linear Burst Sequence A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] 1st address 00 01 10 11 1st address 00 01 10 11 2nd address 01 10 11 00 2nd address 01 00 11 10 3rd address 10 11 00 01 3rd address 10 11 00 01 4th address 11 00 01 10 4th address 11 10 01 00 Note: The burst counter wraps to initial state on the 5th clock. Note: The burst counter wraps to initial state on the 5th clock. BPR 1999.05.18 Sleep Mode During normal operation, ZZ must be pulled low, either by the user or by its internal pull down resistor. When ZZ is pulled high, the SRAM will enter a Power Sleep mode after 2 cycles. At this time, internal state of the SRAM is preserved. When ZZ returns to low, the SRAM operates normally after 2 cycles of wake up time. Sleep mode is a low current, power-down mode in which the device is deselected and current is reduced to ISB2. The duration of Rev: 1.00 10/2001 22/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Sleep mode is dictated by the length of time the ZZ is in a High state. After entering Sleep mode, all inputs except ZZ become disabled and all outputs go to High-Z The ZZ pin is an asynchronous, active high input that causes the device to enter Sleep mode. When the ZZ pin is driven high, ISB2 is guaranteed after the time tZZI is met. Because ZZ is an asynchronous input, pending operations or operations in progress may not be properly completed if ZZ is asserted. Therefore, Sleep mode must not be initiated until valid pending operations are completed. Similarly, when exiting Sleep mode during tZZR, only a Deselect or Read commands may be applied while the SRAM is recovering from Sleep mode. ~ ~ ~ ~ Sleep Mode Timing Diagram CK ZZ tZZR Sleep tZZS tZZH Designing for Compatibility The GSI NBT SRAMs offer users a configurable selection between Flow Through mode and Pipeline mode via the FT signal found on . Not all vendors offer this option, however most mark as VDD or VDDQ on pipelined parts and VSS on flow through parts. GSI NBT SRAMs are fully compatible with these sockets. Absolute Maximum Ratings (All voltages reference to VSS) Symbol Description Value Unit VDD Voltage on VDD Pins -0.5 to 4.6 V VDDQ Voltage in VDDQ Pins -0.5 to 4.6 V VCK Voltage on Clock Input Pin -0.5 to 6 V VI/O Voltage on I/O Pins -0.5 to VDDQ +0.5 ( 4.6 V max.) V VIN Voltage on Other Input Pins -0.5 to VDD +0.5 ( 4.6 V max.) V IIN Input Current on Any Pin +/-20 mA IOUT Output Current on Any I/O Pin +/-20 mA PD Package Power Dissipation 1.5 W TSTG Storage Temperature -55 to 125 oC TBIAS Temperature Under Bias -55 to 125 o C Note: Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended Operating Conditions. Exposure to conditions exceeding the Absolute Maximum Ratings, for an extended period of time, may affect reliability of this component. Rev: 1.00 10/2001 23/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Power Supply Voltage Ranges Parameter Symbol Min. Typ. Max. Unit 3.3 V Supply Voltage VDD3 3.0 3.3 3.6 V 2.5 V Supply Voltage VDD2 2.3 2.5 2.7 V 3.3 V VDDQ I/O Supply Voltage VDDQ3 3.0 3.3 3.6 V 2.5 V VDDQ I/O Supply Voltage VDDQ2 2.4 2.5 2.7 V Notes Notes: 1. The part numbers of Industrial Temperature Range versions end the character "I". Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 2. Input Under/overshoot voltage must be -2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC. VDDQ3 Range Logic Levels Parameter Symbol Min. Typ. Max. Unit Notes VDD Input High Voltage VIH 1.7 -- VDD + 0.3 V 1 VDD Input Low Voltage VIL -0.3 -- 0.8 V 1 VDDQ I/O Input High Voltage VIHQ 1.7 -- VDDQ + 0.3 V 1,3 VDDQ I/O Input Low Voltage VILQ -0.3 -- 0.8 V 1,3 Notes: 1. The part numbers of Industrial Temperature Range versions end the character "I". Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 2. Input Under/overshoot voltage must be -2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC. 3. VIHQ (max) is voltage on VDDQ pins plus 0.3 V. VDDQ2 Range Logic Levels Parameter Symbol Min. Typ. Max. Unit Notes VDD Input High Voltage VIH 0.6*VDD -- VDD + 0.3 V 1 VDD Input Low Voltage VIL -0.3 -- 0.3*VDD V 1 VDDQ I/O Input High Voltage VIHQ 0.6*VDD -- VDDQ + 0.3 V 1,3 VDDQ I/O Input Low Voltage VILQ -0.3 -- 0.3*VDD V 1,3 Notes: 1. The part numbers of Industrial Temperature Range versions end the character "I". Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 2. Input Under/overshoot voltage must be -2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC. 3. VIHQ (max) is voltage on VDDQ pins plus 0.3 V. Rev: 1.00 10/2001 24/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Recommended Operating Temperatures Parameter Symbol Min. Typ. Max. Unit Notes Ambient Temperature (Commercial Range Versions) TA 0 25 70 C 2 Ambient Temperature (Industrial Range Versions) TA -40 25 85 C 2 Note: 1. The part numbers of Industrial Temperature Range versions end the character "I". Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 2. Input Under/overshoot voltage must be -2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC. Undershoot Measurement and Timing Overshoot Measurement and Timing VIH 20% tKC VDD + 2.0 V VSS 50% 50% VDD VSS - 2.0 V 20% tKC VIL Capacitance (TA = 25oC, f = 1 MHZ, VDD = 2.5 V) Parameter Symbol Test conditions Typ. Max. Unit Input Capacitance CIN VIN = 0 V 6.5 7.5 pF Input/Output Capacitance (x36/x72) CI/O VOUT = 0 V 6 7 pF Input/Output Capacitance (x18) CI/O VOUT = 0 V 8.5 9.5 pF Note: These parameters are sample tested. Package Thermal Characteristics Rating Layer Board Symbol Max Unit Notes Junction to Ambient (at 200 lfm) single RJA 40 C/W 1,2 Junction to Ambient (at 200 lfm) four RJA 24 C/W 1,2 Junction to Case (TOP) -- RJC 9 C/W 3 Notes: 1. Junction temperature is a function of SRAM power dissipation, package thermal resistance, mounting board temperature, ambient. Temperature air flow, board density, and PCB thermal resistance. 2. SCMI G-38-87 3. Average thermal resistance between die and top surface, MIL SPEC-883, Method 1012.1 Rev: 1.00 10/2001 25/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) AC Test Conditions Parameter Conditions Input high level 2.3 V Input low level 0.2 V Input slew rate 1 V/ns Input reference level 1.25 V Output reference level 1.25 V Output load Fig. 1& 2 Notes: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted. 3. Output Load 2 for tLZ, tHZ, tOLZ and tOHZ 4. Device is deselected as defined by the Truth Table. Output Load 2 Output Load 1 DQ 2.5 V 50 225 DQ 30pF* 5pF* VT = 1.25 V 225 * Distributed Test Jig Capacitance DC Electrical Characteristics Parameter Symbol Test Conditions Min Max Input Leakage Current (except mode pins) IIL VIN = 0 to VDD -2 uA 2 uA ZZ and PE Input Current IIN1 VDD VIN VIH 0 V VIN VIH -1 uA -1 uA 1 uA 100 uA FT, SCD, ZQ, DP Input Current IIN2 VDD VIN VIL 0 V VIN VIL -100 uA -1 uA 1 uA 1 uA Output Leakage Current (x36/x72) IOL Output Disable, VOUT = 0 to VDD -1 uA 1 uA Output Leakage Current (x18) IOL Output Disable, VOUT = 0 to VDD -2 uA 2 uA Output High Voltage VOH2 IOH = -8 mA, VDDQ = 2.375 V 1.7 V -- Output High Voltage VOH3 IOH = -8 mA, VDDQ = 3.135 V 2.4 V -- Output Low Voltage VOL IOL = 8 mA -- 0.4 V Rev: 1.00 10/2001 26/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Rev: 1.00 10/2001 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 27/46 -- Device Deselected; All other inputs VIH or VIL Deselect Current 280 20 345 20 200 10 580 60 310 30 IDD IDDQ IDD IDDQ IDD IDDQ IDD IDDQ IDD Flow Through Pipeline Flow Through IDD 120 170 IDD Pipeline Flow Through 40 ISB 40 ISB Pipeline Flow Through 200 10 345 15 280 20 IDDQ IDD IDDQ IDD IDDQ IDD IDDQ IDD Flow Through Pipeline Flow Through Pipeline Flow Through Pipeline 520 30 520 40 IDD IDDQ Pipeline IDDQ 310 40 Flow Through Pipeline IDD IDDQ 0 to 70C 580 80 IDD Symbol IDDQ Mode 130 180 60 60 215 10 360 15 300 20 540 30 330 30 600 60 215 10 360 20 300 20 540 40 330 40 560 80 -40 to 85C -250 120 160 40 40 200 10 315 15 280 20 470 30 310 30 530 60 200 10 315 20 280 20 470 40 340 40 530 70 130 170 60 60 215 10 330 15 300 20 490 30 330 30 550 60 215 10 330 20 300 20 490 40 330 40 550 70 -40 to 85C -225 0 to 70C Notes: 1. IDD and IDDQ apply to any combination of VDD3, VDD2, VDDQ3, and VDDQ2 operation. 2. All parameters listed are worst case scenario. -- ZZ VDD - 0.2 V (x18) (x36) (x72) (x18) (x36) (x72) Standby Current 2.5 V Operating Current Device Selected; All other inputs VIH or VIL Output open Device Selected; All other inputs VIH or VIL Output open Operating Current 3.3 V Test Conditions Parameter Operating Currents 100 150 40 40 175 10 290 15 250 20 430 30 270 30 480 50 175 10 290 15 250 20 430 30 270 30 480 60 0 to 70C 110 160 60 60 190 10 305 15 270 20 450 30 290 30 500 50 190 10 305 15 270 20 450 30 290 30 500 60 -40 to 85C -200 100 130 40 40 175 10 250 10 250 20 370 20 270 30 410 40 175 10 250 15 350 20 370 30 270 30 410 50 0 to 70C 110 140 60 60 190 10 265 10 270 20 390 20 290 30 430 40 190 10 265 15 270 20 390 30 290 30 430 50 -40 to 85C -166 100 120 40 40 175 10 230 10 250 20 340 20 270 30 380 40 175 10 230 15 250 20 340 30 270 30 380 50 0 to 70C 110 130 60 60 190 10 245 10 270 20 360 20 290 30 400 40 190 10 245 15 270 20 360 30 290 30 400 50 -40 to 85C -150 90 100 40 40 135 5 205 10 180 10 310 20 200 20 340 30 135 10 205 10 180 20 310 20 200 20 340 40 0 to 70C 100 110 60 60 150 5 220 10 200 10 330 20 220 20 360 30 150 10 220 10 200 20 330 20 220 20 360 40 -40 to 85C -133 mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA mA Unit Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) AC Electrical Characteristics Pipeline Flow Through Parameter Symbol Clock Cycle Time -250 -225 -200 -166 -150 -133 Unit Min Max Min Max Min Max Min Max Min Max Min Max tKC 4.0 -- 4.4 -- 5.0 -- 6.0 -- 6.7 -- 7.5 -- ns Clock to Output Valid tKQ -- 2.3 -- 2.5 -- 3.0 -- 3.4 -- 3.8 -- 4.0 ns Clock to Output Invalid tKQX 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- ns Clock to Output in Low-Z tLZ 1 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- ns Clock Cycle Time tKC 7.0 -- 7.5 -- 8.5 -- 10.0 -- 10.0 -- 15.0 -- ns Clock to Output Valid tKQ -- 6.0 -- 6.0 -- 7.5 -- 8.5 -- 10.0 -- 10.0 ns Clock to Output Invalid tKQX 3.0 -- 3.0 -- 3.0 -- 3.0 -- 3.0 -- 3.0 -- ns Clock to Output in Low-Z tLZ1 3.0 -- 3.0 -- 3.0 -- 3.0 -- 3.0 -- 3.0 -- ns Clock HIGH Time tKH 1.3 -- 1.3 -- 1.3 -- 1.3 -- 1.5 -- 1.7 -- ns Clock LOW Time tKL 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.7 -- 2 -- ns Clock to Output in High-Z tHZ1 1.5 2.3 1.5 2.5 1.5 3.0 1.5 3.5 1.5 3.8 1.5 4.0 ns G to Output Valid tOE -- 2.3 -- 2.5 -- 3.2 -- 3.5 -- 3.8 -- 4.0 ns G to output in Low-Z tOLZ1 0 -- 0 -- 0 -- 0 -- 0 -- 0 -- ns G to output in High-Z tOHZ1 -- 2.3 -- 2.5 -- 3.0 -- 3.5 -- 3.8 -- 4.0 ns Setup time tS 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- ns Hold time tH 0.5 -- 0.5 -- 0.5 -- 0.5 -- 0.5 -- 0.5 -- ns ZZ setup time tZZS2 5 -- 5 -- 5 -- 5 -- 5 -- 5 -- ns ZZ hold time tZZH2 1 -- 1 -- 1 -- 1 -- 1 -- 1 -- ns ZZ recovery tZZR 100 -- 100 -- 100 -- 100 -- 100 -- 100 -- ns Notes: 1. These parameters are sampled and are not 100% tested. 2. ZZ is an asynchronous signal. However, in order to be recognized on any given clock cycle, ZZ must meet the specified setup and hold times as specified above. Rev: 1.00 10/2001 28/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Pipeline Mode Read/Write Cycle Timing 1 2 3 4 5 6 7 8 9 A5 A6 A7 10 CK tS tH tKH tKL tKC CKE tS tH E* tS tH ADV tS tH W tS tH Bn tS tH A0-An A1 A2 A3 A4 tKQ tGLQV tKQHZ tKHQZ tKQLZ DQA-DQD D(A1) tS D (A2+1) D(A2) tH Q(A3) Q(A4) Q (A4+1) D(A5) Q(A6) tKQX tOEHZ tOELZ G COMMAND Write D(A1) Write D(A2) BURST Read Write Q(A3) D(A2+1) Read Q(A4) BURST Read Q(A4+1) Write D(A5) DON'T CARE Read Q(A6) Write D(A7) DESELECT UNDEFINED *Note: E = High (False) if E1 = 1 or E2 = 0 or E3 = 1 Rev: 1.00 10/2001 29/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Pipeline Mode No-Op, Stall and Deselect Timing 1 2 3 4 5 A3 A4 6 7 8 10 9 CK tS tH CKE tS tH E* tS tH ADV tS tH W Bn A0-An A1 A2 A5 tKHQZ D(A1) DQ Q(A2) Q(A3) D(A4) Q(A5) tKQHZ COMMAND Write D(A1) Read Q(A2) STALL Read Q(A3) Write D(A4) STALL NOP DON'T CARE Read Q(A5) DESELECT CONTINUE DESELECT UNDEFINED *Note: E = High (False) if E1 = 1 or E2 = 0 or E3 = 1 Rev: 1.00 10/2001 30/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Flow Through Mode Read/Write Cycle Timing 1 4 3 2 5 6 7 8 9 A5 A6 A7 10 CK tS tH tKH tKL tKC CKE tS tH E* tS tH ADV tS tH W tS tH Bn tS A0-An tH A1 A2 A3 A4 tKQ tKQHZ tGLQV tKHQZ tKQLZ DQ D(A1) tS D(A2) D (A2+1) tH Q(A3) Q (A4+1) Q(A4) D(A5) Q(A6) tKQX tOEHZ tOELZ G COMMAND Write D(A1) Write D(A2) BURST Read Write Q(A3) D(A2+1) Read Q(A4) BURST Read Q(A4+1) Write D(A5) Read Q(A6) DON'T CARE Write D(A7) DESELECT UNDEFINED *Note: E = High (False) if E1 = 1 or E2 = 0 or E3 = 1 Rev: 1.00 10/2001 31/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Flow Through Mode No-Op, Stall and Deselect Timing 1 2 3 4 5 A3 A4 6 8 7 10 9 CK tS tH CKE tS tH E* tS tH ADV W Bn A0-An A1 A2 A5 tKHQZ D(A1) DQ Q(A2) Q(A3) Q(A5) D(A4) tKQHZ COMMAND Write D(A1) Read Q(A2) STALL Read Q(A3) Write D(A4) STALL NOP Read Q(A5) DON'T CARE DESELECT CONTINUE DESELECT UNDEFINED *Note: E = High (False) if E1 = 1 or E2 = 0 or E3 = 1 Rev: 1.00 10/2001 32/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) JTAG Port Operation Due to the fact that this device is built from two die, the two JTAG parts are chained together internally. The following describes the behavior of each die. Overview The JTAG Port on this RAM operates in a manner that is compliant with IEEE Standard 1149.1-1990, a serial boundary scan interface standard (commonly referred to as JTAG). The JTAG Port input interface levels scale with VDD. The JTAG output drivers are powered by VDDQ. Disabling the JTAG Port It is possible to use this device without utilizing the JTAG port. The port is reset at power-up and will remain inactive unless clocked. TCK, TDI, and TMS are designed with internal pull-up circuits.To assure normal operation of the RAM with the JTAG Port unused, TCK, TDI, and TMS may be left floating or tied to either VDD or VSS. TDO should be left unconnected. JTAG Pin Descriptions Pin Pin Name I/O Description TCK Test Clock In Clocks all TAP events. All inputs are captured on the rising edge of TCK and all outputs propagate from the falling edge of TCK. TMS Test Mode Select In The TMS input is sampled on the rising edge of TCK. This is the command input for the TAP controller state machine. An undriven TMS input will produce the same result as a logic one input level. In The TDI input is sampled on the rising edge of TCK. This is the input side of the serial registers placed between TDI and TDO. The register placed between TDI and TDO is determined by the state of the TAP Controller state machine and the instruction that is currently loaded in the TAP Instruction Register (refer to the TAP Controller State Diagram). An undriven TDI pin will produce the same result as a logic one input level. TDI Test Data In TDO Test Data Out Output that is active depending on the state of the TAP state machine. Output changes in Out response to the falling edge of TCK. This is the output side of the serial registers placed between TDI and TDO. Note: This device does not have a TRST (TAP Reset) pin. TRST is optional in IEEE 1149.1. The Test-Logic-Reset state is entered while TMS is held high for five rising edges of TCK. The TAP Controller is also reset automaticly at power-up. JTAG Port Registers Overview The various JTAG registers, refered to as Test Access Port orTAP Registers, are selected (one at a time) via the sequences of 1s and 0s applied to TMS as TCK is strobed. Each of the TAP Registers is a serial shift register that captures serial input data on the rising edge of TCK and pushes serial data out on the next falling edge of TCK. When a register is selected, it is placed between the TDI and TDO pins. Instruction Register The Instruction Register holds the instructions that are executed by the TAP controller when it is moved into the Run, Test/Idle, or the various data register states. Instructions are 3 bits long. The Instruction Register can be loaded when it is placed between the TDI and TDO pins. The Instruction Register is automatically preloaded with the IDCODE instruction at power-up or whenever the controller is placed in Test-Logic-Reset state. Rev: 1.00 10/2001 33/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Bypass Register The Bypass Register is a single bit register that can be placed between TDI and TDO. It allows serial test data to be passed through the RAM's JTAG Port to another device in the scan chain with as little delay as possible. Boundary Scan Register The Boundary Scan Register is a collection of flip flops that can be preset by the logic level found on the RAM's input or I/O pins. The flip flops are then daisy chained together so the levels found can be shifted serially out of the JTAG Port's TDO pin. The Boundary Scan Register also includes a number of place holder flip flops (always set to a logic 1). The relationship between the device pins and the bits in the Boundary Scan Register is described in the Scan Order Table following. The Boundary Scan Register, under the control of the TAP Controller, is loaded with the contents of the RAMs I/O ring when the controller is in Capture-DR state and then is placed between the TDI and TDO pins when the controller is moved to Shift-DR state. SAMPLE-Z, SAMPLE/PRELOAD and EXTEST instructions can be used to activate the Boundary Scan Register. JTAG TAP Block Diagram 0 Bypass Register 2 1 0 Instruction Register TDI TDO ID Code Register 31 30 29 * * * * 2 1 0 Boundary Scan Register n * * * * * * * * * 2 1 0 TMS TCK Test Access Port (TAP) Controller Identification (ID) Register The ID Register is a 32-bit register that is loaded with a device and vendor specific 32-bit code when the controller is put in Capture-DR state with the IDCODE command loaded in the Instruction Register. The code is loaded from a 32-bit on-chip ROM. It describes various attributes of the RAM as indicated below. The register is then placed between the TDI and TDO pins when the controller is moved into Shift-DR state. Bit 0 in the register is the LSB and the first to reach TDO when shifting begins. Rev: 1.00 10/2001 34/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Die Revision Code GSI Technology JEDEC Vendor ID Code I/O Configuration Not Used Presence Register ID Register Contents Bit # 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 x72 X X X X 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 1 0 0 0 1 1 0 1 1 0 0 1 1 x36 X X X X 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 1 0 1 1 0 0 1 1 x32 X X X X 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 1 1 0 1 1 0 0 1 1 x18 X X X X 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 1 0 1 1 0 0 1 1 x16 X X X X 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 1 1 0 1 1 0 0 1 1 Tap Controller Instruction Set Overview There are two classes of instructions defined in the Standard 1149.1-1990; the standard (Public) instructions, and device specific (Private) instructions. Some Public instructions are mandatory for 1149.1 compliance. Optional Public instructions must be implemented in prescribed ways. The TAP on this device may be used to monitor all input and I/O pads, and can be used to load address, data or control signals into the RAM or to preload the I/O buffers. When the TAP controller is placed in Capture-IR state the two least significant bits of the instruction register are loaded with 01. When the controller is moved to the Shift-IR state the Instruction Register is placed between TDI and TDO. In this state the desired instruction is serially loaded through the TDI input (while the previous contents are shifted out at TDO). For all instructions, the TAP executes newly loaded instructions only when the controller is moved to Update-IR state. The TAP instruction set for this device is listed in the following table. Rev: 1.00 10/2001 35/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) JTAG Tap Controller State Diagram 1 0 Test Logic Reset 0 Run Test Idle 1 Select DR 1 Select IR 0 0 1 1 Capture DR Capture IR 0 0 Shift DR 1 1 1 Shift IR 0 1 1 Exit1 DR 0 Exit1 IR 0 0 Pause DR 1 Exit2 DR 1 0 Pause IR 1 Exit2 IR 0 1 Update DR Update IR 1 1 0 0 0 0 Instruction Descriptions BYPASS When the BYPASS instruction is loaded in the Instruction Register the Bypass Register is placed between TDI and TDO. This occurs when the TAP controller is moved to the Shift-DR state. This allows the board level scan path to be shortened to facilitate testing of other devices in the scan path. SAMPLE/PRELOAD SAMPLE/PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE / PRELOAD instruction is loaded in the Instruction Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and I/O buffers into the Boundary Scan Register. Boundary Scan Register locations are not associated with an input or I/O pin, and are loaded with the default state identified in the Boundary Scan Chain table at the end of this section of the datasheet. Because the RAM clock is independent from the TAP Clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents while the input buffers are in transition (i.e. in a metastable state). Although allowing the TAP to sample metastable inputs will not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the TAPs input data capture set-up plus hold time (tTS plus tTH). The RAMs clock inputs need not be paused for any other TAP operation except capturing the I/O ring contents into the Boundary Scan Register. Moving the controller to ShiftDR state then places the boundary scan register between the TDI and TDO pins. EXTEST EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register is loaded with all logic 0s. Rev: 1.00 10/2001 36/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) The EXTEST command does not block or override the RAM's input pins; therefore, the RAM's internal state is still determined by its input pins. Typically, the Boundary Scan Register is loaded with the desired pattern of data with the SAMPLE/PRELOAD command. Then the EXTEST command is used to output the Boundary Scan Register's contents, in parallel, on the RAM's data output drivers on the falling edge of TCK when the controller is in the Update-IR state. Alternately, the Boundary Scan Register may be loaded in parallel using the EXTEST command. When the EXTEST instruction is selected, the sate of all the RAM's input and I/O pins, as well as the default values at Scan Register locations not associated with a pin, are transferred in parallel into the Boundary Scan Register on the rising edge of TCK in the Capture-DR state, the RAM's output pins drive out the value of the Boundary Scan Register location with which each output pin is associated. IDCODE The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction loaded in at power up and any time the controller is placed in the Test-Logic-Reset state. SAMPLE-Z If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (high-Z) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR state. RFU These instructions are Reserved for Future Use. In this device they replicate the BYPASS instruction. JTAG TAP Instruction Set Summary Instruction Code Description Notes EXTEST 000 Places the Boundary Scan Register between TDI and TDO. 1 IDCODE 001 Preloads ID Register and places it between TDI and TDO. 1, 2 SAMPLE-Z 010 Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO. Forces all RAM output drivers to High-Z. 1 RFU 011 Do not use this instruction; Reserved for Future Use. Replicates BYPASS instruction. Places Bypass Register between TDI and TDO. 1 SAMPLE/ PRELOAD 100 Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO. 1 GSI 101 GSI private instruction. 1 RFU 110 Do not use this instruction; Reserved for Future Use. Replicates BYPASS instruction. Places Bypass Register between TDI and TDO. 1 BYPASS 111 Places Bypass Register between TDI and TDO. 1 Notes: 1. Instruction codes expressed in binary, MSB on left, LSB on right. 2. Default instruction automatically loaded at power-up and in test-logic-reset state. Rev: 1.00 10/2001 37/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) JTAG Port Recommended Operating Conditions and DC Characteristics Parameter Symbol Min. Max. Unit Notes 3.3 V Test Port Input High Voltage VIHJ3 2.0 VDD3 +0.3 V 1 3.3 V Test Port Input Low Voltage VILJ3 -0.3 0.8 V 1 2.5 V Test Port Input High Voltage VIHJ2 0.6 * VDD2 VDD2 +0.3 V 1 2.5 V Test Port Input Low Voltage VILJ2 -0.3 0.3 * VDD2 V 1 TMS, TCK and TDI Input Leakage Current IINHJ -300 1 uA 2 TMS, TCK and TDI Input Leakage Current IINLJ -1 100 uA 3 TDO Output Leakage Current IOLJ -1 1 uA 4 Test Port Output High Voltage VOHJ 1.7 -- V 5, 6 Test Port Output Low Voltage VOLJ -- 0.4 V 5, 7 Test Port Output CMOS High VOHJC VDDQ - 100 mV -- V 5, 8 Test Port Output CMOS Low VOLJC -- 100 mV V 5, 9 Notes: 1. Input Under/overshoot voltage must be -2 V > Vi < VDDn +2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tTKC. 2. VILJ VIN VDDn 3. 0 V VIN VILJn 4. Output Disable, VOUT = 0 to VDDn 5. The TDO output driver is served by the VDDQ supply. 6. IOHJ = -4 mA 7. IOLJ = + 4 mA 8. IOHJC = -100 uA 9. IOHJC = +100 uA JTAG Port AC Test Conditions Parameter Conditions Input high level 2.3 V Input low level 0.2 V Input slew rate 1 V/ns Input reference level 1.25 V Output reference level 1.25 V 50 30pF* VT = 1.25 V * Distributed Test Jig Capacitance Notes: 1. Include scope and jig capacitance. 2. Test conditions as as shown unless otherwise noted. Rev: 1.00 10/2001 JTAG Port AC Test Load DQ 38/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) JTAG Port Timing Diagram tTKH tTKL tTKC TCK tTS tTH TMS TDI TDO tTKQ JTAG Port AC Electrical Characteristics Parameter Symbol Min Max Unit TCK Cycle Time tTKC 50 -- ns TCK Low to TDO Valid tTKQ -- 20 ns TCK High Pulse Width tTKH 20 -- ns TCK Low Pulse Width tTKL 20 -- ns TDI & TMS Set Up Time tTS 10 -- ns TDI & TMS Hold Time tTH 10 -- ns Rev: 1.00 10/2001 39/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) GS8324Z18/36/72 Boundary Scan Chain Order Order x72 x36 x18 Bump x72 x36 x18 1(TBD) Notes: 1. Depending on the package, some input pads of the scan chain may not be connected to any external pin. In such case: LBO = 1, ZQ = 1, PE = 0, SD = 0, ZZ = 0, FT = 1, DP = 1, and SCD = 1. 2. Every DQ pad consists of two scan registers--D is for input capture, and Q is for output capture. 3. A single register (#194) for controlling tristate of all the DQ pins is at the end of the scan chain (i.e., the last bit shifted in this tristate control is effective after JTAG EXTEST instruction is executed. 4. 1 = no connect, internally set to logic value 1 5. 0 = no connect, internally set to logic value 0 6. X = no connect, value is undefined Rev: 1.00 10/2001 40/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) 209 BGA Package Drawing 14 mm x 22 mm Body, 1.0 mm Bump Pitch, 11 x 19 Bump Array C A1 A Side View D aaa D1 b Symbol Min Typ A Max Units 1.70 mm 0.40 0.50 0.60 mm b 0.50 0.60 0.70 mm c 0.31 0.36 0.38 mm D 21.9 22.0 22.1 mm 18.0 (BSC) E 13.9 14.0 Bottom View e A1 D1 E E1 e mm 14.1 mm E1 10.0 (BSC) mm e 1.00 (BSC) mm aaa 0.15 mm Rev 1.0 Rev: 1.00 10/2001 41/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Package Dimensions--119-Pin PBGA 119-Bump BGA Package A Pin 1 Corner 7 6 5 4 3 2 1 A B C D E F G H J K L M N P R T U A B C D E F G H J K L M N P R T U G B S D R Bottom View Top View Symbol Description Min. Nom. Max A Width 13.9 14.0 14.1 B Length 21.9 22.0 22.1 C Package Height (including ball) 1.73 1.86 1.99 D Ball Size 0.60 0.75 0.90 E Ball Height 0.50 0.60 0.70 F Package Height (excluding balls) 1.16 1.26 1.36 G Width between Balls K Package Height above board R Width of package between balls 7.62 S Length of package between balls 20.32 T Variance of Ball Height 0.15 1.27 0.65 0.70 0.75 C F E K T Package Dimensions--119-Pin PBGA Unit: mm Side View Rev: 1.00 10/2001 42/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Ordering Information for GSI Synchronous NBT SRAMs Org Part Number1 Type Package Speed2 (MHz/ns) TA3 2M x 18 GS8324Z18B-250 Pipeline/Flow Through 119 BGA 250/6 C 2M x 18 GS8324Z18B-225 Pipeline/Flow Through 119 BGA 225/6.5 C 2M x 18 GS8324Z18B-200 Pipeline/Flow Through 119 BGA 200/7.5 C 2M x 18 GS8324Z18B-166 Pipeline/Flow Through 119 BGA 166/8.5 C 2M x 18 GS8324Z18B-150 Pipeline/Flow Through 119 BGA 150/10 C 2M x 18 GS8324Z18B-133 Pipeline/Flow Through 119 BGA 133/11 C 2M x 18 GS8324Z18C-250 Pipeline/Flow Through 209 BGA 250/6 C 2M x 18 GS8324Z18C-225 Pipeline/Flow Through 209 BGA 225/6.5 C 2M x 18 GS8324Z18C-200 Pipeline/Flow Through 209 BGA 200/7.5 C 2M x 18 GS8324Z18C-166 Pipeline/Flow Through 209 BGA 166/8.5 C 2M x 18 GS8324Z18C-150 Pipeline/Flow Through 209 BGA 150/10 C 2M x 18 GS8324Z18C-133 Pipeline/Flow Through 209 BGA 133/11 C 1M x 36 GS8324Z36B-250 Pipeline/Flow Through 119 BGA 250/6 C 1M x 36 GS8324Z36B-225 Pipeline/Flow Through 119 BGA 225/6.5 C 1M x 36 GS8324Z36B-200 Pipeline/Flow Through 119 BGA 200/7.5 C 1M x 36 GS8324Z36B-166 Pipeline/Flow Through 119 BGA 166/8.5 C 1M x 36 GS8324Z36B-150 Pipeline/Flow Through 119 BGA 150/10 C 1M x 36 GS8324Z36B-133 Pipeline/Flow Through 119 BGA 133/11 C 1M x 36 GS8324Z36C-250 Pipeline/Flow Through 209 BGA 250/6 C 1M x 36 GS8324Z36C-225 Pipeline/Flow Through 209 BGA 225/6.5 C 1M x 36 GS8324Z36C-200 Pipeline/Flow Through 209 BGA 200/7.5 C 1M x 36 GS8324Z36C-166 Pipeline/Flow Through 209 BGA 166/8.5 C 1M x 36 GS8324Z36C-150 Pipeline/Flow Through 209 BGA 150/10 C 1M x 36 GS8324Z36C-133 Pipeline/Flow Through 209 BGA 133/11 C 512K x 72 GS8324Z72C-250 Pipeline/Flow Through 209 BGA 250/6 C 512K x 72 GS8324Z72C-225 Pipeline/Flow Through 209 BGA 225/6.5 C 512K x 72 GS8324Z72C-200 Pipeline/Flow Through 209 BGA 200/7.5 C 512K x 72 GS8324Z72C-166 Pipeline/Flow Through 209 BGA 166/8.5 C 512K x 72 GS8324Z72C-150 Pipeline/Flow Through 209 BGA 150/10 C Notes: 1. Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. Example: GS8324Z18B-150IB. 2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each device is Pipeline/Flow Through mode-selectable by the user. 3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range. 4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings. Rev: 1.00 10/2001 43/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Ordering Information for GSI Synchronous NBT SRAMs (Continued) Org Part Number1 Type Package Speed2 (MHz/ns) TA3 512K x 72 GS8324Z72C-133 Pipeline/Flow Through 209 BGA 133/11 C 2M x 18 GS8324Z18B-250I Pipeline/Flow Through 119 BGA 250/6 I 2M x 18 GS8324Z18B-225I Pipeline/Flow Through 119 BGA 225/6.5 I 2M x 18 GS8324Z18B-200I Pipeline/Flow Through 119 BGA 200/7.5 I 2M x 18 GS8324Z18B-166I Pipeline/Flow Through 119 BGA 166/8.5 I 2M x 18 GS8324Z18B-150I Pipeline/Flow Through 119 BGA 150/10 I 2M x 18 GS8324Z18B-133I Pipeline/Flow Through 119 BGA 133/11 I 2M x 18 GS8324Z18C-250I Pipeline/Flow Through 209 BGA 250/6 I 2M x 18 GS8324Z18C-225I Pipeline/Flow Through 209 BGA 225/6.5 I 2M x 18 GS8324Z18C-200I Pipeline/Flow Through 209 BGA 200/7.5 I 2M x 18 GS8324Z18C-166I Pipeline/Flow Through 209 BGA 166/8.5 I 2M x 18 GS8324Z18C-150I Pipeline/Flow Through 209 BGA 150/10 I 2M x 18 GS8324Z18C-133I Pipeline/Flow Through 209 BGA 133/11 I 1M x 36 GS8324Z36B-250I Pipeline/Flow Through 119 BGA 250/6 I 1M x 36 GS8324Z36B-225I Pipeline/Flow Through 119 BGA 225/6.5 I 1M x 36 GS8324Z36B-200I Pipeline/Flow Through 119 BGA 200/7.5 I 1M x 36 GS8324Z36B-166I Pipeline/Flow Through 119 BGA 166/8.5 I 1M x 36 GS8324Z36B-150I Pipeline/Flow Through 119 BGA 150/10 I 1M x 36 GS8324Z36B-133I Pipeline/Flow Through 119 BGA 133/11 I 1M x 36 GS8324Z36C-250I Pipeline/Flow Through 209 BGA 250/6 I 1M x 36 GS8324Z36C-225I Pipeline/Flow Through 209 BGA 225/6.5 I 1M x 36 GS8324Z36C-200I Pipeline/Flow Through 209 BGA 200/7.5 I 1M x 36 GS8324Z36C-166I Pipeline/Flow Through 209 BGA 166/8.5 I 1M x 36 GS8324Z36C-150I Pipeline/Flow Through 209 BGA 150/10 I 1M x 36 GS8324Z36C-133I Pipeline/Flow Through 209 BGA 133/11 I 512K x 72 GS8324Z72C-250I Pipeline/Flow Through 209 BGA 250/6 I Notes: 1. Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. Example: GS8324Z18B-150IB. 2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each device is Pipeline/Flow Through mode-selectable by the user. 3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range. 4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings. Rev: 1.00 10/2001 44/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) Ordering Information for GSI Synchronous NBT SRAMs (Continued) Org Part Number1 Type Package Speed2 (MHz/ns) TA3 512K x 72 GS8324Z72C-225I Pipeline/Flow Through 209 BGA 225/6.5 I 512K x 72 GS8324Z72C-200I Pipeline/Flow Through 209 BGA 200/7.5 I 512K x 72 GS8324Z72C-166I Pipeline/Flow Through 209 BGA 166/8.5 I 512K x 72 GS8324Z72C-150I Pipeline/Flow Through 209 BGA 150/10 I 512K x 72 GS8324Z72C-133I Pipeline/Flow Through 209 BGA 133/11 I Notes: 1. Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. Example: GS8324Z18B-150IB. 2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each device is Pipeline/Flow Through mode-selectable by the user. 3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range. 4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings. Rev: 1.00 10/2001 45/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc. Preliminary GS8324Z18(B/C)/GS8324Z36(B/C)/GS8324Z72(C) 36Mb Sync SRAM Datasheet Revision History DS/DateRev. Code: Old; New 8324Z18_r1 Rev: 1.00 10/2001 Types of Changes Format or Content Page;Revisions;Reason * Creation of new datasheet 46/46 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 2001, Giga Semiconductor, Inc.