TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL LS25~150 Series Instruction Manual BEFORE USING THE POWER SUPPLY UNIT Pay attention to all warnings and cautions before using the unit. Incorrect usage could lead to an electrical shock, damage to the unit or a fire hazard. WARNING and CAUTION z Do not modify. z Do not touch the internal components, they may have high voltage or high temperature. You may get electrical shock or burned. z When the unit is operating, keep your hands and face away from it as you may be injured by flying debris in the event of a fault. z This power supply is designed for use within an end product. Stick the WARNING label for users on the system equipment and notify in the system instruction manual. z Never operate the unit under over current or short-circuit conditions for more than 30 seconds or outside its specified Input Voltage Range, which could result in damage. There is no possibility of fire or burning. z Confirm connections to input/output terminals are correct as indicated in the instruction manual. z This power supply has a possibility for hazardous voltage to appear at output terminal depending on the type of failure. The outputs of these products must be earthed in the end equipment to maintain SELV. If the outputs are not earthed, they must be considered hazardous and must not be made user accessible. Note: CE MARKING CE marking, when applied to the LS series products, indicates compliance with the Low Voltage Directive (2006/95/EC) in that it complies with EN60950-1. DWG NO. : PA582-04-01-D APPD CHK DWG TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL 1. Terminal Explanation LS25, LS35, LS50, LS75 1 2 3 FG : Frame Ground - V : - Output terminal +V : + Output terminal Output voltage adjustable trimmer Output monitoring indicator (Green LED : ON) 4 -V +V 5 H V ADJ (3) (4) (5) (6) (7) Live line (Fuse in line) Neutral line L N (1) L : Input terminal (2) N : Input terminal LS100, LS150 L N (1) L : Input terminal (2) N : Input terminal Live line(Fuse in line) Neutral line 1 2 3 -V -V +V +V V ADJ : Frame Ground (3) FG (4) -V : - Output terminal ( 25A max./ terminal) (5) +V : + Output terminal ( 25A max./ terminal) (6) Output voltage adjustable trimmer (7) Output monitoring indicator (Green LED : ON) 4 5 6 7 H 2. Terminal connecting method z z z Input must be off when making connection. Connect FG terminal to ground terminal of the equipment. The output load line and input line shall be separated and twisted to improve noise immunity. LS25, LS35, LS50, LS75 LS100, LS150 L N L N LOAD H V ADJ + H -V -V +V +V V ADJ -V +V + LOAD Maximum output current of each output terminal is 25A except for LS25 (15A). If more than 25A, use 2 terminals. 1 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL 3. Explanation of Functions and Precautions 3-1. Input Voltage Range Input voltage range is single phase 88 ~ 264VAC (47 ~ 63Hz) or 125 ~ 373VDC for LS25 ~ LS100. For LS150, selectable switch 115/230VAC will decide the input voltage range as mentioned in the table below. Input voltage which is out of specification, may damage the unit. For cases where conformance to various safety specs(UL,CSA,EN) are required, input voltage range will be 100~240VAC (50/60Hz ). Note : LS series able to withstand Input Surge of 300VAC for 5 seconds. LS150 - Selectable voltage range Selected Range Applicable Input Voltage Range in VAC 115 88 ~ 132 230 176 ~ 264 Applicable Input Voltage Range in VDC NA 248 ~ 373 3-2. Output Voltage Range V.ADJ trimmer is for output voltage adjustment within the range of specifications. Turning the trimmer clockwise will increase the output voltage. Note over voltage protection ( OVP ) function may trigger if the output voltage is increased excessively. 3-3. Inrush Current Power Thermistor is built in to protect the circuit from high Inrush Current. Please select suitable input switch and fuse rating in case of re-input the power at high temperature. 3-4. Over Voltage Protection (OVP) The OVP function will shutdown the output except for LS25. The input need to be removed for a few minutes, and then re-input for recovery of the output. OVP setting is fixed and cannot be adjusted externally. Note : For LS25, OVP function will cause the output into "hiccup" mode and damage the unit. 3-5. Over Current Protection (OCP) OCP function operates when the output current exceeds OCP specifications. The output will automatically recover when the overload condition is removed. Do not operate overload or dead short conditions for more than 30 seconds, which could result in damage. There is no possibility of fire or burning. 3-6. Output Ripple & Noise Ripple & noise are measured at 20MHz by using a 300mm twisted pair of load wires terminated with a 0.1uF film capacitor & 47uF electrolytic capacitor. When load lines are longer, ripple becomes larger. The output ripple cannot be measured accurately if the probe ground lead of oscilloscope is too long. At low temperature, large ripple & noise may also be observed due to large ESR of the internal Electrolytic Capacitors especially at -25degC. Output voltage rise may not be smooth during initial turn on at low temperature. 2 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL 3-7. Series Operation For series operation, either method ( A ) or ( B ) is possible. Method ( A ) Method ( B ) Power Supply Power Supply Output Terminal Output Terminal Load Output Terminal Load Load Output Terminal Note : In case of Method ( A ), please connect diodes to prevent the reverse voltage. 3-8. Parallel Operation (A) (B) 1. 2. 3. Operation to increase the Output Current is not possible. Operation as a Backup Power Supply is possible as follows. Set the power supply output voltage higher by the amount of forward voltage drop ( VF ) of the diode. Please adjust the output voltage of each power supply to be the same. Please use within the specifications for output voltage and output current. (A) (B) Power Supply Power Supply Output Terminal Output Terminal Load Output Terminal Load Output Terminal 3 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL 4. Isolation / Withstand Voltage 4-1. Isolation Test Isolation resistance between output and FG (chassis) shall be more than 100M at 500VDC. For safety, voltage setting of DC isolation tester must be done before the test. Ensure that the unit is fully discharged after the test. (a) Output ~ FG (chassis) : 500VDC, 100M or more AC(L) +V AC(N) +V -V Isolation Tester -V FG 4-2. Withstand Voltage This series is designed to withstand 3.0kVAC between input and output, 1.5kVAC between input and FG (chassis) and 500VAC between output and FG (chassis) each for 1 minute. When testing withstand voltage, set current limit of withstand voltage test equipment at 20mA ( Output-FG (chassis) : 100mA ). The applied voltage must be gradually increased from zero to testing value and then gradually decreased for shut down. When timer is used, the power supply may be damaged by high impulse voltage at timer switch on and off. Connect input and output as follows : (a) Input ~ FG (chassis) : solid line 1.5kVAC, 1min (20mA) (c) Output ~ FG (chassis) : 500VAC, 1min (100mA) (b) Input ~ Output : dotted line 3kVAC, 1min ( 20mA ) AC(L) AC(N) +V +V -V -V FG AC(L) +V AC(N) +V -V -V FG Withstand Voltage Tester Withstand Voltage Tester 4 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL 5. Mounting Directions 5-1. Output Derating according to the Mounting Directions Recommended standard mounting is Method ( A ). Method ( B ), ( C ) and ( D ) are also possible. Refer to the Output Derating below. Please do not use installation Method ( E ), where the PCB will be on the topside and heat will be trapped inside the unit. In the following derating curve, the maximum output current is denoted as 100%. (A) Output Derating versus Ambient Temperature (Convection Cooling) LS25-3.3 Output Derating Vs Ambient Temperature Load (%) 120 100 Mounting A&D 80 60 Mounting B&C 50 40 20 0 -25 0 25 40 65 70 50 o Ambient Temperature ( C) 5 75 100 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL LS25-5, -12, -15, -24, -36 & -48 Output Derating Vs Ambient Temperature Load (%) 120 100 Mounting A&D 80 60 50 Mounting B&C 40 20 0 -25 0 25 40 65 70 50 75 100 o Ambient Temperature ( C) LS35-3.3, -5, -12, -15, -24, -36 & -48 Output Derating Vs Ambient Temperature Load (%) 120 100 Mounting A,B & D 80 60 50 Mounting C 40 20 0 -25 0 25 45 65 70 50 o Ambient Temperature ( C) 6 75 100 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL LS50-3.3, -5, -12, -15, -24, -36 & -48 Load (%) Output Derating Vs Ambient Temperature 120 100 Mounting 80 A, B & D 70 60 50 Mounting 40 C 20 0 -25 0 25 40 60 50 70 75 100 Ambient Temperature (C) LS75-3.3, -5 Load (%) Output Derating Vs Ambient Temperature 120 100 Mounting 80 A, B & D 70 60 Mounting 40 C 20 0 -25 0 25 45 50 60 Ambient Temperature (C) 7 70 75 100 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL LS75-12, -15, -24, -36 & -48 Load (%) Output Derating Vs Ambient Temperature 120 100 Mounting 80 A, B & D 70 60 Mounting 40 C 20 0 -25 0 25 50 60 70 100 75 Ambient Temperature (C) LS100-3.3, -5 Load (%) Output Derating Vs Ambient Temperature 120 100 Mounting 80 A&B 60 50 Mounting 40 C&D 20 0 -25 0 25 40 45 50 Ambient Temperature (C) 8 70 75 100 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL LS100-12, -15, -24, -36 & -48 Output Derating Vs Ambient Temperature Load (%) 120 100 Mounting 80 A&B 60 50 Mounting 40 C&D 20 0 -25 0 45 25 70 50 75 100 Ambient Temperature (C) LS150-3.3, -5 Load (%) Output Derating Vs Ambient Temperature 120 100 Mounting 80 A 60 50 Mounting 40 B, C & D 20 0 -25 0 25 30 40 50 Ambient Temperature (C) 9 70 75 100 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL LS150-12, -15, -24, -36 & -48 Load (%) Output Derating Vs Ambient Temperature 120 100 Mounting 80 A 70 60 Mounting 40 B, C & D 20 0 -25 0 25 40 50 70 75 100 Ambient Temperature (C) (B) Output Derating versus Input Voltage (Convection Cooling) LS100-3.3, -5, -12, -15, -24, -36 & -48 Output Derating Vs Input Voltage LOAD (%) 120 100 80 60 40 20 0 88 115 230 Vin (VAC) NOTE : LS25, LS35, LS50, LS75 & LS150 series do not require Input Voltage Derating. 10 264 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL 5-2 Mounting Method 1) 2) 3) This is convection cooling type power supply. In consideration of the heat radiation and safety, please keep a distance of more than 15mm between the power supply and the peripheral parts. When lining up multiple units, please make sure to place them 15mm or more apart from each other. Maximum allowable penetration of mounting screws into the power-supply is 5mm except LS25 (4mm). Recommended torque for mounting screws of LS25 ~ LS150 (M3 screw) : 0.49 Nm (5.0 kgfcm). 6. Wiring Method z The input and output load wires shall be separated and twisted to improve noise immunity. z Both wires must be as thick and short as possible to make lower impedance. z Noise can be reduced by connecting a film capacitor with 0.1uF capacitance across the load terminals. z For safety and EMI considerations, connect the FG terminal of LS series to mounting set ground terminal. z The recommended wire type : MODEL Recommended Wire Recommended torque Recommended crimp-type terminal D t Mounting (MAX) (MAX) Pieces (MAX) LS25 AWG16-22 M3.0 Screws 0.49 Nm (5.0 kgfcm) 6.0mm 0.8mm 2 pieces LS35 ~ LS150 AWG14-22 M3.5 Screws 1.0 Nm (9.8 kgfcm) ~ 1.4 Nm (13.7 kgfcm) 6.8mm 0.8mm 2 pieces Note 1 : When using separate loads, it is recommended to use 2 pieces of 0.8mm thick crimp-type terminal. Note 2 : For recommended wire diameter, refer to wire maker recommended allowable current and voltage drop. For higher output current model like 3.3V & 5V, bigger diameter wire is recommended. 11 TDK-Lambda LS 25-150 Series INSTRUCTION MANUAL 7. External Fuse Rating Refer to the following fuse rating when selecting the external input fuse. Surge current flows when input turns on. Fuse rating is specified by Inrush Current value at input turn on. Do not select the fuse according to input current (rms) values under the actual load condition. LS25 LS35, LS50 LS75 LS100 LS150 : : : : : F1.6A , 250V T2A , 250V T2.5A , 250V F4A , 250V F5A , 250V 8. Before concluding that the unit is at fault, make the following checks. z z z z z z Check if the rated input voltage is connected. Check if the wiring of input and output is correct. Check if the wire size is correct. Check if the output voltage trimmer (V.ADJ) is properly adjusted. Check if the output current and output wattage does not exceed the specification. Ensure that a large capacitor is not connected across the output terminals. Please use within maximum capacitance shown below. MODEL LS25 LS35~LS50 LS75~LS150 3.3V 5V 10,000uF 10,000uF 12V 5,000uF 10,000uF Maximum external capacitance 15V 24V 2,000uF 1,000uF 5,000uF 2,000uF 5,000uF 36V 48V 500uF 500uF 1,000uF NOTE : It is normal to hear audible noise from power-supply under Dynamic Load operation or if the input voltage waveform is not sinusoidal. 9. Warranty Condition This product is under warranty for 3 years (based on 8 hours/day operation) from the date of shipment. During the warranty period, TDK-Lambda will, at it's option, either repair or replace products prove to be defective. Warranty applies but not limited to the following. (1) Average operating temperature (ambient temperature of the power supply unit) is under 40oC. (2) Average load factor is 80% or less. (3) Installation method : Standard installation. Following cases are not covered by warranty. (1) Improper usage and mis-handling like dropping or applying shock to the unit and defects from operation exceeding specification of the product. (2) Defects resulting from natural disaster (fire, flood). (3) Unauthorized modification or repair. 12