Part No: CEP-2202AS
Description: piezo audio indicator
Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062
Date: 9/18/2006
Unit: mm
Page No: 1 of 5
Specifications
Resonant frequency 3.0 KHz ± 0.5
Operating voltage 3 ~ 20 V dc
Current consumption 11 mA max. at 12 V dc
Sound pressure level 85 db min. at 30 cm / 12 V dc
Rated voltage 12 V dc
Tone Continuous
Operating temperature -30 ~ +85° C
Storage temperature -40 ~ +95° C
Dimensions ø24.2 x H16.0 mm
Weight 5 g max.
Material ABS UL-94 1/16” HB High Heat (Black)
Terminal Pin type (Sn Plating)
RoHS yes
Appearance Drawing
Tolerance: ±0.5
For more information, please visit the product page.
Part No: CEP-2202AS
Description: piezo audio indicator
Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062
Date: 9/18/2006
Unit: mm
Page No: 2 of 5
Measurement Method
S.P.L. Measuring Circuit
Mic: RION S.P.L. meter UC 30 or equivalent
For more information, please visit the product page.
Part No: CEP-2202AS
Description: piezo audio indicator
Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062
Date: 9/18/2006
Unit: mm
Page No: 3 of 5
Environment Test
noitidnoC tseTmetI
rof C°59+ ta rebmahc a ni decalp gnieb retfAtset .pmet hgiH
240 hours.
rof C°04- ta rebmahc a ni decalp gnieb retfAtset .pmet woL
240 hours.
dna C°04+ ta rebmahc a ni decalp gnieb retfAtset ytidimuH
90±5% relative humidity for 240 hours.
Temp. cycle test The part shall be subjected to 5 cycles. One
cycle will consist of:
Evaluation Standard
The buzzer will be measured after
being placed at +25°C for 4
hours. The value of the
oscillation frequency/current
consumption should be ±10%
compared to the initial
measurements. The SPL should
be within ±10dB compared to the
initial measurements.
Mechanical Characteristics
noitidnoC tseTmetI
rof nisor ni desremmi era slanimret daeLytilibaredloS
5 seconds and then immersed in solder bath
of 270 ±5°C for 3 ±1 seconds.
Soldering Heat Resistance Lead terminals are immersed up to 1.5mm from
buzzer’s body in solder bath of 300 ±5°C for
3 ±0.5 seconds or 260 ±5°C for 10 ±1 seconds.
Terminal Mechanical Strength For 10 seconds, the force of 9.8N (1.0kg) is
applied to each terminal in axial direction.
gniylppa retfa derusaem eb llahs rezzub ehTnoitarbiV
a vibration amplitude of 1.5 mm with 10 to
55 Hz band of vibration frequency to each of
the 3 perpendicular directions for 2 hours.
fo thgieh a morf deppord eb lliw trap ehTtseT porD
75 cm onto a 40 mm thick wooden board 3
times in 3 axes (X, Y, Z) for a total of 9 drops.
Evaluation Standard
90% min. of the lead terminals
will be wet with solder. (Except
the edge of the terminal)
No interference in operation.
No damage or cutting off.
The value of oscillation
frequency/current consumption
should be ±10% of the initial
measurements. The SPL should
be within ±10dB compared with
the initial measurement.
1
Notes: 1. Not recommended for wave soldering
For more information, please visit the product page.
Part No: CEP-2202AS
Description: piezo audio indicator
Phone: 800.275.4899 Fax: 503.612.2381 www.cui.com 20050 SW 112th Ave. Tualatin, OR 97062
Date: 9/18/2006
Unit: mm
Page No: 4 of 5
Reliability Test
Item Test Condition
Operating (Life Test) 1. Continuous life test:
The part will be subjected to 48 hours of
continuous operation at +70°C with rated
voltage applied.
2. Intermittent life test:
A duty cycle of 1 minute on, 1 minutes off, a
minimum of 5,000 times at room temp
(+25 ±2°C) with rated voltage applied.
Evaluation Standard
The buzzer will be measured after
being placed at +25°C for 4
hours. The value of the
oscillation frequency/current
consumption should be ±10%
compared to the initial
measurements. The SPL should
be within ±10dB compared to
the initial measurements.
Test Conditions
Standard Test Condition a) Tempurature: +5 ~ +35°C b) Humidity: 45 - 85% c) Pressure: 860-1060 mbar
Judgement Test Condition a) Tempurature: +25 ±2°C b) Humidity: 60 - 70% c) Pressure: 860-1060 mbar
For more information, please visit the product page.
