LP3918 LP3918 Battery Charge Management and Regulator Unit Literature Number: SNVS476C LP3918 Battery Charge Management and Regulator Unit General Description Features The LP3918 is a fully integrated charger and multi-regulator unit designed for CDMA cellular phones. The LP3918 contains a Li-Ion battery charger, 7 low noise low dropout (LDO) voltage regulators and a high-speed serial interface to program on/off conditions and output voltages of individual regulators, and also to read status information from the PMU. The Li-Ion charger integrates a power FET, reverse current blocking diode, sense resistor with current monitor output, and requires only a few external components. Charging is thermally regulated to obtain the most efficient charging rate for a given ambient temperature. LDO regulators provide high PSRR and low noise ideally suited for supplying power to both analog and digital loads. Fully integrated Li-Ion battery charger with thermal Applications CDMA Phone Handsets Low Power Wireless Handsets Handheld Information Appliances Personal Media Players Digital Cameras regulation USB Charge Mode. 7 Low Noise LDO's 2 x 300 mA 3 x 150 mA 2 x 80 mA I2C compatible interface for controlling LDO outputs and charger operation Thermal shutdown Under Voltage Lockout 25-bump Thin micro-SMD package 2.5 x 2.5 mm Options available on request, please contact sales office for further information; - Level detect on HF_PWR & PWR_ON - LDO Charging mode - Custom Default Settings on Charger, and LDO O/P's. Key Specifications 50mA to 950mA Programmable Charge Current 3.0V to 5.5V Input Voltage Range 200mV typ. Dropout Voltage on 300 mA LDO's 2% (typ) Output Voltage Accuracy on LDO's Simplified Functional Block Diagram 20211601 (c) 2009 National Semiconductor Corporation 202116 www.national.com LP3918 Battery Charge Management and Regulator Unit April 28, 2009 LP3918 Device Pin Diagram LP3918 25 pin micro-SMD Package TOP VIEW 20211634 Package Marking Information 20211604 -- -- -- -- The physical placement of the package marking will vary from part to part. Date Code. XYTT format. `XY' 2 digit date code; `TT' - dierun code MNK - Package Marking See National web page for more info - http://www.national.com/quality/marking_conventions.html Ordering Information Order Number Connector Debounce LDO MODE Package Marking LP3918TL-L NO YES V008 LP3918TLX-L LP3918TL-A 250 units, Tape & Reel 1000 units, Tape & Reel YES NO LP3918TLX-A www.national.com Supplied As V011 250 units, Tape & Reel 1000 units, Tape & Reel 2 LP3918 LP3918 Pin Descriptions Pin # Type Description A1 IMON Name A Charge current monitor output. This pin presents an analog voltage representation of the input charging current. VIMON(mV) = (2.47 x ICHG)(mA). A2 PS_HOLD DI Input for power control from external processor/controller. A3 VSS G Digital Ground pin A4 RESET_N DO Reset Output. Pin stays LOW during power up sequence. 60ms after LDO1 (CORE) is stable this pin is asserted HIGH. A5 ACOK_N DO AC Adapter indicator, LOW when 4.5V - 6.0V present at CHG_IN. B1 CHG_IN P DC power input to charger block from wall or car power adapters. B2 PWR_ON DI Power up sequence starts when this pin is set HIGH. Internal 500k pull-down resistor. B3 SCL DI Serial Interface Clock input. External pull up resistor is needed, typ 1.5k B4 PON_N DO Active low signal is PWR_ON inverted B5 LDO7 C1 C2 C3 SDA C4 TX_EN DI Enable control for LDO6 (TX). HIGH = Enable, LOW = Disable. C5 LDO6 A LDO6 Output (TX) D1 VIN1 P Battery Input for LDO1 - 2 D2 TCXO_EN DI Enable control for LDO4 (TCXO). HIGH = Enable, LOW = Disable. D3 GNDA G Analog Ground pin D4 RX_EN DI Enable control for LDO5 (RX). HIGH = Enable, LOW = Disable. D5 LDO5 A LDO5 Output (RX) E1 LDO1 A LDO1 Output (CORE) E2 LDO2 A LDO2 Output (DIGI) E3 LDO3 A LDO3 Output (ANA) E4 LDO4 A LDO4 Output (TCXO) E5 VIN2 P Battery Input for LDO3 - 7 A LDO7 Output (GP) BATT P Main battery connection. Used as a power connection for current delivery to the battery. HF_PWR DI Power up sequence starts when this pin is set HIGH. Internal 500k pull-down resistor. A: Analog. G: Ground. DI/O D: Digital. O: Output. Serial Interface, Data Input/Output Open Drain output, external pull up resistor is needed, typ 1.5k. I: Input. DI/O: Digital Input/Output. P: Power. 3 www.national.com LP3918 Applications Schematic Diagram 20211605 * * Device Description The LP3918 Charge Management and Regulator Unit is designed to supply charger and voltage output capabilities for mobile systems, e.g. CDMA handsets. The device provides a Li-Ion charging function and 7 regulated outputs. Communication with the device is via an I2C compatible serial interface that allows function control and status read-back. The battery charge management section provides a programmable CC/CV linear charge capability. Following a normal charge cycle a maintenance mode keeps battery voltage between programmable levels. Power levels are thermally regulated to obtain optimum charge levels over the ambient temperature range. * * * * * * REGULATORS 7 Low dropout linear regulators provide programmable voltage outputs with current capabilities of 80mA, 150mA and 300mA as given in the table below. LDO1, LDO2 and LDO3 are powered up by default with LDO1 reaching regulation before LDO2 and LDO3 are started. LDO1, LDO3 and LDO7 can be disabled/enabled via the serial interface. During power up LDO1 and LDO2 must reach their regulation voltage detection point for the device to power up and remain powered. LDO4, LDO5 and LDO6 have external enable pins and may power up following LDO2 as determined by their respective enable. Under voltage lockout oversees device start up with preset level of 2.85V(typ). Charger Features * Pre-charge, CC, CV and Maintenance modes * USB Charge 100mA/450mA * Integrated FET * Integrated Reverse Current Blocking Diode * Integrated Sense Resistor * Thermal regulation * Charge Current Monitor Output * Programmable charge current 50mA - 950mA with 50mA steps * Default CC mode current 100mA www.national.com Pre-charge current fixed 50mA Termination voltage 4.1V, 4.2V (default), 4.3V, and 4.4V, accuracy better than +/- 0.5% (typ) Restart level 50mV, 100mV, 150mV (default) and 200mV below Termination voltage End of Charge 0.1C (default), 0.15C, 0.2C and 0.25C Programmable Enable Control Safety timer Input voltage operating range 4.5V - 6.0V LDO mode on LP3918TL-L option. 4 DEVICE PROGRAMMABILITY An I2C compatible Serial Interface is used to communicate with the device to program a series of registers and also to read status registers. These internal registers allow control over LDO outputs and their levels. The charger functions may also be programmed to alter termination voltage, end of charge current, charger restart voltage, full rate charge current, and also the charging mode. This device internal logic is powered from LDO2. TABLE 1. LDO Default Voltages LDO Function mA Default Voltage (V) Startup Default Enable Control 1 CORE 300 1.8 ON SI 2 DIGI 300 3.0 ON - 3 ANA 80 3.0 ON SI 4 TCXO 80 3.0 OFF TCXO_EN 5 RX 150 3.0 OFF RX_EN 6 TX 150 3.0 OFF TX_EN 7 GP 150 3.0 OFF SI TABLE 2. LDO Output Voltages Selectable via Serial Interface LDO mA 1.5 1.8 1.85 2.5 2.6 2.7 2.75 2.8 2.85 2.9 2.95 3.0 3.05 3.1 3.2 3.3 + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + 1 CORE 300 2 DIGI 300 3 ANA 80 4 TCXO 80 5 RX 150 + + + + + + + + 6 TX 150 + + + + + + + + 7 GP 150 + + + + + + + + + + + + + + + + + + 5 www.national.com LP3918 POWER SUPPLY CONFIGURATIONS At PMU start up, LDO1, LDO2 and LDO3 are always started with their default voltages. The start up sequence of the LDO's is given below. Startup Sequence LDO1 -> LDO2 -> LDO3 LDO's with external enable control (LDO4, LDO5, LDO6) start immediately after LDO2 if enabled by logic high at their respective control inputs. LDO7 (and LDO1 and 3) may be programmed to enable/disable once PS_HOLD has been asserted. Default voltages for the LDOs are shown in Table 1 and Table 2 shows the voltages that may be programmed via the Serial Interface. LP3918 HF_PWR, PWR_ON ACOK_N, SDA, SCL, RX_EN, TX_EN, TCXO_EN, PS_HOLD, RESET_N All other pins Junction Temperature (TJ) Ambient Temperature (TA) Absolute Maximum Ratings (Notes 1, 2) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. CHG-IN, VBATT =VIN1/2, BATT,HF_PWR All other Inputs Junction Temperature (TJ-MAX) Storage Temperature Max Continuous Power Dissipation (PD-MAX) (Note 3) ESD (Note 4) Batt, VIN1, VIN2, HF_PWR, CHG_IN, PWR_ON All other pins Operating Ratings -0.3 to +6.5V -0.3 to +6V -0.3 to VBATT +0.3V, max 6.0V 150C -40C to +150C 0V to 5.5V 0V to (VLDO2 + 0.3V) 0V to (VBATT + 0.3V) -40C to +125C -40 to 85C Thermal Properties (Note 9) Junction to Ambient Thermal Resistance JA Internally Limited Jedec Standard Thermal PCB 4L Cellphone Board 37C/W 66C/W 8kV HBM 2kV HBM (Notes 1, 2) CHG_IN VBATT =VIN1/2, BATT 4.5 to 6.0V 3.0 to 5.5V General Electrical Characteristics Unless otherwise noted, VIN ( = VIN1 = VIN2 = BATT) = 3.6V, GND = 0V, CVIN1-2=10F, CLDOX=1F. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, Ta = TJ = -40C to +125C. (Note 6) Symbol IQ(STANDBY) Parameter Standby Supply Current Condition Typ VIN= 3.6V, UVLO on, internal logic circuit on, all other circuits off 2 Limit Min Max Units 10 A 3.0 V Power Monitor Functions Battery Under-Voltage Lockout VUVLO-R Under Voltage Lock-out VIN Rising 2.85 (Note 7) 160 2.7 Thermal Shutdown TSD Threshold www.national.com 6 C Parameter Condition Typ Limit Min Units Max LOGIC AND CONTROL INPUTS (LDO2 at 3.0V) VIL Input Low Level VIH Input High Level IIL Logic Input Current PS_HOLD, SDA, SCL, RX_EN, TCXO_EN, TX_EN 0.25* VLDO2 V PWR_ON, HF_PWR 0.25* VBATT V PS_HOLD, SDA, SCL, RX_EN, TCXO_EN, TX_EN 0.75* VLDO2 V PWR_ON, HF_PWR 0.75* VBATT V All logic inputs except PWR_ON and HF_PWR -5 +5 A 0V VINPUT VBATT RIN Input Resistance PWR_ON, HF_PWR Pull-Down resistance to GND(Note 7) 500 k LOGIC AND CONTROL OUTPUTS (LDO2 at 3.0V) VOL VOH Output Low Level Output High Level PON_N, RESET_N, SDA, ACOK_N IOUT = 2mA 0.25* V VLDO2 PON_N, RESET_N, ACOK_N IOUT = 2mA 0.75* VLDO2 V (Not applicable to Open Drain Output SDA) LDO1 (CORE) Electrical Characteristics Unless otherwise noted, VIN ( = VIN1 = VIN2 = BATT) = 3.6V, GND = 0V, CVIN1-2=10F, CLDOX=1F. VOUT1 set to 3.0V output. Note VINMIN is the greater of 3.0V or VOUT1+ 0.5V. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, Ta = TJ = -40C to +125C. (Note 6) Symbol VOUT1 Parameter Output Voltage Accuracy Condition Typ IOUT1 = 1mA, VOUT1= 3.0V Output Voltage Default Output Current VINMIN VIN 5.5V Output Current Limit VOUT1 = 0V 600 VDO1 Dropout Voltage IOUT1 = 300mA, (Note 8) 200 VOUT1 Line Regulation VINMIN VIN 5.5V IOUT1 Limit Min Max -2 +2 -3 +3 1.8 Units % V 300 mA 280 mV 2 mV IOUT1 = 1mA en1 Load Regulation 1mA IOUT1 300mA 20 mV Output Noise Voltage 10Hz f 100KHz, 45 VRMS 65 dB COUT = 1F (Note 7) PSRR Power Supply Rejection Ratio F = 10kHz, COUT = 1F IOUT1 = 20mA (Note 7) tSTART-UP Start-Up Time from Shut-down TTransient Start-Up Transient Overshoot COUT = 1F, IOUT1 = 300mA 60 170 s 60 120 mV (Note 7) COUT = 1F, IOUT1 = 300mA (Note 7) 7 www.national.com LP3918 Symbol LP3918 LDO2 (DIGI) Electrical Characteristics Unless otherwise noted, VIN ( = VIN1 = VIN2 = BATT) = 3.6V, GND = 0V, CVIN1-2=10F, CLDOX=1F. Note VINMIN is the greater of 3.0V or VOUT2+ 0.5V. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, Ta = TJ = -40C to +125C.(Note 6) Symbol VOUT2 Parameter Output Voltage Accuracy Condition Typ IOUT2 = 1mA, VOUT2= 3.0V Output Voltage Default Output Current VINMIN VIN 5.5V Output Current Limit VOUT2 = 0V 600 VDO2 Dropout Voltage IOUT2 = 300mA (Note 8) 200 VOUT2 Line Regulation VINMIN VIN 5.5V IOUT2 Limit Min Max -2 +2 -3 +3 3.0 Units % V 300 mA 280 mV 2 mV IOUT2 = 1mA en2 Load Regulation 1mA IOUT2 300mA 20 mV Output Noise Voltage 10Hz f 100KHz, 45 VRMS 65 dB COUT = 1F (Note 7) PSRR Power Supply Rejection Ratio F = 10kHz, COUT = 1F IOUT2 = 20mA (Note 7) tSTART-UP Start-Up Time from Shut-down tTransient Start-Up Transient Overshoot COUT = 1F, IOUT2 = 300mA 40 60 s 5 30 mV (Note 7) COUT = 1F, IOUT2 = 300mA (Note 7) LDO3 (ANA), LDO4 (TCXO) Electrical Characteristics Unless otherwise noted, VIN ( = VIN1 = VIN2 = BATT) = 3.6V, GND = 0V, CVIN1-2=10F, CLDOX=1F. TCXO_EN high. Note VINMIN is the greater of 3.0V or VOUT3/4 + 0.5V. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, Ta = TJ = -40C to +125C. (Note 6) Symbol VOUT3, VOUT4 Parameter Output Voltage Accuracy Output Voltage Condition Typ IOUT3/4 = 1mA, VOUT3/4= 3.0V LDO3 default 3.0 LDO4 default 3.0 Output Current VINMIN VIN 5.5V Output Current Limit VOUT3/4 = 0V 160 VDO3, VDO4 Dropout Voltage IOUT3/4 = 80mA (Note 8) 180 VOUT3 , Line Regulation VINMIN VIN 5.5V IOUT3, IOUT4 VOUT4 Limit Min Max -2 +2 -3 +3 Units % V 80 mA 220 mV 2 mV IOUT3/4 = 1mA Load Regulation 1mA IOUT3/4 80mA 20 mV en3,en4 Output Noise Voltage 10Hz f 100kHz, COUT = 1F (Note 7) 45 VRMS PSRR Power Supply Rejection Ratio F = 10kHz, COUT = 1F 65 dB tSTART-UP Start-Up Time from Shut-down COUT = 1F, IOUT3/4 = 80mA (Note 7) 40 60 s tTransient Start-Up Transient Overshoot COUT = 1F, IOUT3/4 = 80mA (Note 7) 5 30 mV IOUT3/4 = 20mA (Note 7) www.national.com 8 Unless otherwise noted, VIN ( = VIN1 = VIN2 = BATT) = 3.6V, GND = 0V, CVIN1-2=10F, CLDOX=1F. RX_EN, TX_EN high. LDO7 Enabled via Serial Interface. Note VINMIN is the greater of 3.0V or VOUT5/6/7 + 0.5V. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, Ta = TJ = -40C to +125C. (Note 6) Symbol Parameter VOUT5, Output Voltage VOUT6, VOUT7 Output Voltage Condition Typ IOUT5/6/7 = 1mA, VOUT5/6/7= 3.0V LDO5 default 3.0 LDO6 default 3.0 LDO7 default 3.0 IOUT5, IOUT6, Output Current IOUT7 Output Current Limit VINMIN VIN 5.5V VOUT5/6/7 = 0V 300 VDO5, VDO6, VDO7 Dropout Voltage IOUT5/6/7 = 150mA (Note 8) 180 VOUT5, Line Regulation VINMIN VIN 5.5V VOUT6, Limit Min Max -2 +2 -3 +3 Units % V 150 mA 240 mV 2 mV IOUT5/6/7 = 1mA VOUT7 Load Regulation 1mA IOUT5/6/7 150mA 20 mV en5, en6, en7 Output Noise Voltage 10Hz f 100kHz, COUT = 1F (Note 7) 45 VRMS PSRR Power Supply Rejection Ratio F = 10kHz, COUT = 1F 65 dB IOUT5/6/7 = 20mA (Note 7) tSTART-UP Start-Up Time from Shut-down COUT = 1F, IOUT5/6/7 = 150mA (Note 7) 40 60 s tTransient Start-Up Transient Overshoot COUT = 1F, IOUT5/6/7 = 150mA (Note 7) 5 30 mV 9 www.national.com LP3918 LDO5 (RX), LDO6 (TX), LDO7 (GP) Electrical Characteristics LP3918 Charger Electrical Characteristics Unless otherwise noted, VCHG-IN = 5V, VIN ( = VIN1 = VIN2 = BATT) = 3.6V.CCHG_IN = 10F, CBATT = 30F. Charger set to default settings unless otherwise noted. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, Ta = TJ = -25C to +85C. (Notes 6, 9) Symbol VCHG-IN Parameter Condition Typ Max Input Voltage Range 4.5 6.5 Operating Range 4.5 6 VOK_CHG CHG_IN OK trip-point VCHG_IN - VBATT (Falling) 50 VTERM Battery Charge Termination voltage Default 4.2 VTERM voltage tolerance TJ = 25C ICHG Limit Min VCHG_IN - VBATT (Rising) 200 Units V mV V -0.35 +0.35 % TJ = 0C to 85C -1 +1 Fast Charge Current Accuracy ICHG = 450mA -10 +10 % Programmable full-rate charge current range (default 100mA) 6.0V VCHG_IN 4.5V 50 950 mA 40 60 mA VBATT < (VCHG_IN - VOK_CHG) VFULL_RATE < VBATT < VTERM (Note 10) Default 100 Charge current programming step 50 IPREQUAL Pre-qualification current VBATT = 2V ICHG_USB CHG_IN programmable current in USB mode 50 5.5V VCHG_IN 4.5V Low VBATT < (VCHG_IN - VOK_CHG) 100 VFULL_RATE < VBATT < VTERM High 450 Default = 100mA 100 VBATT rising, transition from pre-qual to full-rate charging 3.0 VFULL_RATE Full-rate qualification threshold IEOC End of Charge Current, % 0.1C option selected of full-rate current VRESTART Restart threshold voltage VBATT falling, transition from EOC to full-rate charge mode. Default options selected - 4.05V 4.05 IMON Voltage 1 ICHG = 100mA 0.247 IMON Voltage 2 ICHG = 450mA 1.112 Regulated junction temperature (Note 7) 115 IMON TREG mA 2.9 3.1 10 V % 3.97 4.13 V 0.947 1.277 V C Detection and Timing (Note 7) TPOK Power OK deglitch time VBATT < (VCC - VOK_CHG) 32 mS TPQ_FULL Deglitch time Pre-qualification to full-rate charge transition 230 mS TCHG Charge timer Precharge mode 1 Hrs Full Rate Charging Timeout 5 Constant Voltage Timeout 5 TEOC www.national.com Deglitch time for end-ofcharge transition 230 10 mS Unless otherwise noted, VIN ( = VIN1 = VIN2 = BATT) = 3.6V, GND = 0V, CVIN1-2=10F, CLDOX=1F, and VLDO2 (DIG) = 3.0V. Typical values and limits appearing in normal type apply for TJ = 25C. Limits appearing in boldface type apply over the entire junction temperature range for operation, Ta = TJ = -40C to +125C. (Notes 6, 7) Symbol Parameter Condition Typ Limit Min Max 400 Units fCLK Clock Frequency tBF Bus-Free Time between START and STOP 1.3 s tHOLD Hold Time Repeated START Condition 0.6 s tCLK-LP CLK Low Period 1.3 s tCLK-HP CLK High Period 0.6 s tSU Set-Up Time Repeated START Condition 0.6 s tDATA-HOLD Data Hold Time 50 ns tDATA-SU Data Set-Up Time 100 ns tSU Set-Up Time for STOP Condition 0.6 s tTRANS Maximum Pulse Width of Spikes that Must be Suppressed by the Input Filter of both DATA & CLK Signals 50 kHz ns Note 1: Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: All voltages are with respect to the potential at the GND pin. Note 3: Internal Thermal Shutdown circuitry protects the device from permanent damage. Note 4: The human-body model is 100pF discharged through 1.5k. The machine model is a 200pF capacitor discharged directly into each pin, MIL-STD-883 3015.7. Note 5: Care must be exercised where high power dissipation is likely. The maximum ambient temperature may have to be derated. Like the Absolute Maximum power dissipation, the maximum power dissipation for operation depends on the ambient temperature. In applications where high power dissipation and/or poor thermal dissipation exists, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA_MAX) is dependent on the maximum power dissipation of the device in the application (PD_MAX), and the junction to ambient thermal resistance of the device/package in the application (JA), as given by the following equation: TA_MAX = TJ_MAX-OP - (JA X PDMAX ). Note 6: All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production with TJ = 25C. All hot and cold limits are guaranteed by correlating the electrical characteristics to process and temperature variations and applying statistical process control. Note 7: Guaranteed by design. Note 8: Dropout voltage is the input-to-output voltage difference at which the output voltage is 100mV below its nominal value. This specification does not apply in cases it implies operation with an input voltage below the 3.0V minimum appearing under Operating Ratings. For example, this specification does not apply for devices having 1.5V outputs because the specification would imply operation with an input voltage at or about 1.5V. Note 9: Junction-to-ambient thermal resistance (JA) is taken from thermal modelling result, performed under the conditions and guidelines set forth in the JEDEC standard JESD51-7. The value of (JA) of this product could fall within a wide range, depending on PWB material, layout, and environmental conditions. In applications where high maximum power dissipation exists (high VIN, high IOUT), special care must be paid to thermal dissipation issues in board design. Note 10: Full charge current is guaranteed for CHG_IN = 4.5 to 6.0V. At higher input voltages, increased power dissipation may cause the thermal regulation to limit the current to a safe level, resulting in longer charging time. 11 www.national.com LP3918 Serial Interface LP3918 Register Information, Slave Address Code 7h'7E TABLE 3. Control Registers Addr Register (default value) 8h'00 D7 D6 D5 D4 D3 D2 D1 D0 OP_EN (0000 0101) X X X X LDO7_EN LDO3_EN X LDO1_EN 8h'01 LDO1PGM O/P (0000 0001) X X X X V1_OP[3] V1_OP[2] V1_OP[1] V1_OP[0] 8h'02 LDO2PGM O/P (0000 1011) X X X X V2_OP[3] V2_OP[2] V2_OP[1] V2_OP[0] 8h'03 LDO3PGM O/P (0000 1011) X X X X V3_OP[3] V3_OP[2] V3_OP[1] V3_OP[0] 8h'04 LDO4PGM O/P (0000 1011) X X X X V4_OP[3] V4_OP[2] V4_OP[1] V4_OP[0] 8h'05 LDO5PGM O/P (0000 1011) X X X X V5_OP[3] V5_OP[2] V5_OP[1] V5_OP[0] 8h'06 LDO6PGM O/P (0000 1011) X X X X V6_OP[3] V6_OP[2] V6_OP[1] V6_OP[0] 8h'07 LDO7PGM O/P (0000 1011) X X X X V7_OP[3] V7_OP[2] V7_OP[1] V7_OP[0] 8h'0C STATUS (0000 0000) PWR_ON _TRIG HF_PWR _TRIG CHG_IN _TRIG X X X X X 8h'10 CHGCNTL1 (0000 1001) TOUT_ doubling EN_Tout En_EOC X EN_CHG 8h'11 CHGCNTL2 (0000 0001) Prog_ ICHG[4] Prog_ ICHG[3] Prog_ ICHG[2] Prog_ ICHG[1] Prog_ ICHG[0] 8h'12 CHGCNTL3 (0001 0010) VTERM[1] VTERM[0] Prog_ EOC[1] Prog_ EOC[0] Prog_ VRSTRT[1] Prog_ VRSTRT[0] EOC Tout_ Fullrate Tout_ Prechg LDO Mode Fullrate PRECHG 8h'14 CHGSTATUS2 Tout_ ConstV Bad_Batt 8h'1C MISC Control1 APU_TSD_EN PS_HOLD _DELAY 8h'13 CHGSTATUS1 X (R/O) USBMODE CHGMODE Force EOC _EN _EN Batt_Over _Out CHGIN_ OK_Out Not Used Bits are Read Only type. Codes other than those shown in the table are disallowed. Note that for Serial Interface operation and thus register control, LDO2 must be active to provide the power for the internal logic. www.national.com 12 The following table summarizes the supported output voltages for the LP3918. Default voltages after startup are highlighted in bold. TABLE 4. Data Code (Reg 01 - 07) LDO1 V LDO2 V VLDO3 V LDO4 V LDO5 V LDO6 V LDO7 V 8h'00 1.5 1.5 8h'01 1.8 1.8 1.8 8h'02 1.85 1.85 1.85 8h'03 2.5 2.5 2.5 2.5 8h'04 2.6 2.6 2.6 8h'05 2.7 2.7 2.7 2.7 2.7 2.7 2.7 8h'06 2.75 2.75 2.75 2.75 2.75 2.75 2.75 8h'07 2.8 2.8 2.8 2.8 2.8 2.8 2.8 8h'08 2.85 2.85 2.85 2.85 2.85 2.85 2.85 8h'09 2.9 2.9 2.9 2.9 2.9 2.9 2.9 8h'0A 2.95 2.95 2.95 2.95 2.95 2.95 2.95 8h'0B 3.0 3.0 3.0 3.0 3.0 3.0 3.0 8h'0C 3.05 3.05 3.05 3.05 3.05 3.05 3.05 8h'0D 3.1 3.1 3.1 3.1 8h'0E 3.2 3.2 3.2 3.2 8h'0F 3.3 3.3 3.3 3.3 1.5 2.6 Charger Control Register 2 Note that Bits 7,6,5 are not used and must be set to 0 during write to this register. CHARGER CURRENT PROGRAMMING The following table summarizes the supported charging current values for the LP3918. Default charge current after startup is highlighted in bold TABLE 5. LP3918 Charger Current Programming Address Register ID 8h'11 CHGCNTL2 Address Register ID 8h'11 CHGCNTL2 Address Register ID 8h'11 CHGCNTL2 Current Selection Prog_ICHG<4..0> Bit 0 to Bit 4 00000 00001 00010 00011 00100 00101 00110 50mA 100mA 150mA 200mA 250mA 300mA 350mA Current Selection Prog_ICHG<4..0> Bit 0 to Bit 4 00111 01000 01001 01010 01011 01100 01101 400mA 450mA 500mA 550mA 600mA 650mA 700mA 01110 01111 10000 10001 10010 750mA 800mA 850mA 900mA 950mA Current Selection Prog_ICHG<4..0> Bit 0 to Bit 4 13 www.national.com LP3918 LDO Output Voltage Programming LP3918 Charger Control Register 3 CHARGER TERMINATION VOLTAGE PROGRAMMING TABLE 6. LP3918 Charger Termination Voltage Control Address 8h'12 Register ID VTERM Selection Bits VTERM[1] VTERM[0] CHGCNTL3<5> CHGCNTL3<4> 0 0 4.1 0 1 4.2 (Default) 1 0 4.3 1 1 4.4 CHGCNTL3 Termination Voltage(V) END OF CHARGE CURRENT PROGRAMMING TABLE 7. LP3918 EOC Current Control Address 8h'12 Register ID End Of Charge Current Selection Bits PROG_EOC[1] PROG_EOC[0] CHGCNTL3<3> CHGCNTL3<2> 0 0 0.1 (Default) 0 1 0.15C 1 0 0.2C 1 1 0.25C CHGCNTL3 End Of Charge Current CHARGING RESTART VOLTAGE PROGRAMMING TABLE 8. LP3918 Charging Restart Voltage Address 8h'12 Register ID Charging Restart Voltage Selection Bits PROG_VRSTRT[1] PROG_VRSTRT[1] CHGCNTL3<1> CHGCNTL3<0> 0 0 0 1 VTERM - 100mV 1 0 VTERM - 150mV 1 1 VTERM - 200mV CHGCNTL3 Restart Voltage(V) VTERM - 50mV Charger Control Register 1 CHARGING MODE SELECTION Charging mode selection changes will only take place when the battery voltage is above the 3.0V pre-charge/Full-rate charge threshold. TABLE 9. LP3918 USB Charging Selection Address 8h'10 www.national.com Register ID CHGCNTL1 USB Charge Mode Control Bits USB_Mode_En CHG_Mode_En CHGCNTL1<7> CHGCNTL1<6> Mode Current 0 1 0 Fast Charge Default or Selection 0 Fast Charge Default or Selection 0 1 USB 100mA 1 1 USB 450mA 14 LP3918 Device Power Up and Shutdown Timing Device Power Up Logic Timing. PWR_ON 20211637 15 www.national.com LP3918 Device Power Up Logic Timing. CHG_IN, HF_PWR 20211607 www.national.com 16 LP3918 LP3918 Power On Behaviour (Failed PS_Hold) 20211608 LP3918 Normal Shutdown Behaviour 20211633 17 www.national.com LP3918 Functional Block Diagram 20211602 LP3918 Functional Block Diagram www.national.com 18 LP3918 Technical Description BATTERY CHARGE MANAGEMENT A charge management system allowing the safe charge and maintenance of a Li-Ion battery is implemented on the LP3918. This has a CC/CV linear charge capability with programmable battery regulation voltage and end of charge current threshold. The charge current in the constant current mode is programmable and a maintenance mode monitors for battery voltage drop to restart charging at a preset level. A USB charging mode is also available with 2 charge current levels. 20211638 CHARGER FUNCTION Following the correct detection of an input voltage at the charger pin the charger enters a pre-charge mode. In this mode a constant current of 50mA is available to charge the battery to 3.0V. At this voltage level the charge management applies the default (100mA) full rate constant current to raise the battery voltage to the termination voltage level (default 4.2V). The full rate charge current may be programmed to a different level at this stage. When termination voltage (VTERM) is reached, the charger is in constant voltage mode and a constant voltage of 4.2V is maintained. This mode is complete when the end of charge current (default 0.1C) is detected and the charge management enters the maintenance mode. In maintenance mode the battery voltage is monitored for the restart level (4.05V at the default settings) and the charge cycle is re-initiated to re-establish the termination voltage level. For start up the EOC function is disabled. This function should be enabled once start up is complete and a battery has been detected. EOC is enabled via register CHGCNTL1, Table 10. The full rate constant current rate of charge may be programmed to 19 levels from 50mA to 950mA. These values are given in Table 5, and Table 12 The charge mode may be programmed to USB mode when the charger input is applied and the battery voltage is above 3.0V. This provides two programmable current levels of 100mA and 450mA for a USB sourced supply input at CHG_IN. Table 9 FIGURE 1. LDO Mode Diagram EOC EOC is disabled by default and should be enabled when the system processor is awake and the system detects that a battery is present. Programming Information TABLE 10. Register Address 8h'10: CHGCNTL1 BIT NAME 2 En_EOC FUNCTION Enables the End Of Charge current level threshold detection. When set to '0' the EOC is disabled. The End Of Charge current threshold default setting is at 0.1C. This EOC value is set relative to C the set full rate constant current. This threshold can be set to 0.1C, 0.15C, 0.2C or 0.25C bychanging the contents of the PROG_EOC[1:0] register bits. TABLE 11. Register Address 8h'12: CHGCNTL3 BIT NAME 2 Prog_EOC[0] 3 Prog_EOC[1] FUNCTION Set the End Of Charge Current. See Table 9 LDO Mode on device option LP3918TL-L The charger circuit automatically enters an LDO mode if no battery is detected on insertion of the charger input voltage. In LDO mode the battery pin is regulated to 4.2V and can source up to 1.0A of current. Normal operation with a battery connected can be re-established via the serial interface. The serial interface allows the device to switch between modes as required however care is required to ensure that LDO mode is not initiated while a battery is present. 19 www.national.com LP3918 TERMINATION AND RESTART The termination and restart voltage levels are determined by the data in the VTERM[1:0] and PROG_VSTRT[1:0] bits in the control register. The restart voltage is programmed relative to the selected termination voltage. The Termination voltages available are 4.1V, 4.2V (default), 4.3V, and 4.4V. The Restart voltages are determined relative to the termination voltage level and may be set to 50mV, 100mV, 150mV (default), and 200mV below the set termination voltage level. CHARGER FULL RATE CURRENT Programming Information TABLE 12. Register Address 8h'11: CHGCNTL2 Data BITs HEX NAME 000[00000] 00 Prog_ICHG 000[00001] 01 100mA 000[00010] 02 150mA 000[00011] 03 200mA 000[00100] 04 250mA 000[00101] 05 300mA 000[00110] 06 350mA BIT NAME 000[00111] 07 400mA 4 VTERM[0] 000[01000] 08 450mA 5 VTERM[1] 000[01001] 09 500mA 000[01010] 0A 550mA 000[01011] 0B 600mA 000[01100] 0C 650mA 000[01101] 0D 700mA 000[01110] 0E 750mA 000[01111] 0F 800mA 000[10000] 10 850mA 000[10001] 11 900mA 000[10010] 12 950mA www.national.com FUNCTION 50mA Programming Information TABLE 13. Register Address 8h'12: CHGCNTL3 FUNCTION Set the charging termination voltage. See Table 6 TABLE 14. Register Address 8h'12: CHGCNTL3 20 BIT NAME 0 VRSTRT[0] 1 VRSTRT[1] FUNCTION Set the charging restart voltage. See Table 8 LP3918 Charger Operation The operation of the charger with EOC enabled is shown in this simplified flow diagram. 20211636 FIGURE 2. Simplified Charger Functional Flow Diagram (EOC is enabled) 21 www.national.com LP3918 The charger operation may be depicted by the following graphical representation of the voltage and current profiles. 20211635 FIGURE 3. Charge Cycle Diagram Further Charger Register Information Charger Status Register 1 Read only Charger Control Register 1 TABLE 16. Register Address 8h'13: CHGSTATUS1 BIT NAME FUNCTION (if bit = '1') 7 BAT_OVER _OUT 6 CHGIN_ OK_Out Is set when a valid input voltage is detected at CHG_IN pin. 5 EOC Is set when the charging current decreases below the programmed End Of Charge levlel. TABLE 15. Register Address 8h'10: CHGCNTL1 BIT NAME 7 USB_MODE _EN Sets the Current Level in USB mode. CHG_MODE _EN Forces the charger into USB mode when active high. If low, charger is in normal charge mode. 6 FUNCTION (if bit = '1') Is set when battery voltage exceeds 4.7V. 5 FORCE _EOC Forces an EOC event. 4 Tout_ Fullrate 4 TOUT_ Doubling Doubles the timeout delays for all timeout signals. 3 Tout_ Precharge Set after timeout for precharge mode. 3 EN_Tout Enables the timeout counters. When set to '0' the timeout counters are disabled. 2 LDO_Mode Only available on LP3918TL_L. 1 Fullrate Set when the charger is in CC/CV mode. Enables the End of Charge current level threshold detection. When set to '0' the functions are disabled. 0 PRECHG 2 1 0 EN_EOC Set_ LDOmode EN_CHG www.national.com Set after timeout on full rate charge. Set during precharge. Charger Status Register 2 Read only TABLE 17. Register Address 8h'13: CHGSTATUS2 Forces the charger into LDO mode. Function available on LP3918TL_L. BIT NAME FUNCTION (if bit = '1') 1 Tout_ ConstV Set after timeout in CV phase. 0 BAD_ BATT Charger enable. 22 Set at bad battery state. LP3918 IMON CHARGE CURRENT MONITOR Charge current is monitored within the charger section and a proportional voltage representation of the charge current is presented at the IMON output pin. The output voltage relationship to the actual charge current is represented in the following graph and by the equation: VIMON(mV) = (2.47 x ICHG)(mA) PROGRAMMING INFORMATION Enable via Serial Interface TABLE 18. Register Address 8h'00: OP_EN BIT NAME 0 LDO1_EN 2 LDO3_EN 3 LDO7_EN FUNCTION Bit set to '0' - LDO disabled Bit set to '1' - LDO enabled Note that the default setting for this Register is [0000 0101]. This shows that LDO1 and 3 are enabled by default whereas LDO7 is not enabled by default on start up. LDO OUTPUT PROGRAMMING TABLE 19. Regi ster Add (hex) NAME Data Range (hex) 01 LDO1PGM O/P 03 - 0F 1.5V to 3.3V (def. 1.8V) 02 LDO2PGM O/P 00 - 0F 2.5V to 3.3V (def 3.0V) 03 LDO3PGM O/P 05 - 0C 2.7V to 3.05V (def 3.0V) 04 LDO4PGM O/P 00 - 0F 1.5V to 3.3V (def 3.0V) 05 LDO5PGM O/P 05 - 0C 2.7V to 3.05V (def 3.0V) 06 LDO6PGM O/P 05 - 0C 2.7V to 3.05V (def 3.0V) 07 LDO7PGM O/P 00 - 0F 1.5V to 3.3V (def 3.0V) 20211611 FIGURE 4. IMON Voltage vs Charge Current Note that this function is not available if there is no input at CHG_IN or if the charger is off due to the input at CHG_IN being outwith the operating voltage range. LDO Information OPERATIONAL INFORMATION The LP3918 has 7 LDO's of which 3 are enabled by default, LDO's 1,2 and 3 are powered up during the power up sequence. LDO4, 5 and 6 are separately, externally enabled and will follow LDO2 in start up if their respective enable pin is pulled high. LDO2, LDO3 and LDO7 can be enabled/disabled via the serial interface. LDO2 must remain in regulation otherwise the device will power down. While LDO1 is enabled this must also be in regulation for the device to remain powered. If LDO1 is disabled via I2C interface the device will not shut down. Output Voltage See Table 2 for full programmable range of values. EXTERNAL CAPACITORS The Low Drop Out Linear Voltage regulators on the LP3918 require external capacitors to ensure stable outputs. The LDO's on the LP3918 are specifically designed to use small surface mount ceramic capacitors which require minimum board space. These capacitors must be correctly selected for good performance INPUT VOLTAGES There are two input voltage pins used to power the 7LDO's on the LP3918. VIN2is the supply for LDO3, LDO4, LDO5, LDO6 and LDO7. VIN1is the supply for LDO1 and LDO2. These input voltages should be tied to the Batt pin in the application. 23 www.national.com LP3918 frequency of operation. Capacitor values will also show some decrease over time due to aging. The capacitor parameters are also dependant on the particular case size with smaller sizes giving poorer performance figures in general. INPUT CAPACITOR Input capacitors are required for correct operation. It is recommended that a 10F capacitor be connected between each of the voltage input pins and ground (this capacitance value may be increased without limit). This capacitor must be located a distance of not more than 1cm from the input pin and returned to a clean analogue ground. A ceramic capacitor is recommended although a good quality tantalum or film capacitor may be used at the input. Important: Tantalum capacitors can suffer catastrophic failures due to surge current when connected to a lowimpedance source of power (like a battery or a very large capacitor). If a tantalum capacitor is used at the input, it must be guaranteed by the manufacturer to have surge current rating sufficent for the application. There are no requirements for the ESR (Equivalent Series Resistance) on the input capacitor, but tolerance and temparature coefficient must be considered when selecting the capacitor to ensure the capacitance will remain within its operational range over the entire operating temperature range and conditions. Output Capacitor 20211612 Correct selection of the output capacitor is critical to ensure stable operation in the intended application.The output capacitor must meet all the requirements specified in the recommended capacitor table over all conditions in the application. These conditions include DC-bias, frequency and temperature. Unstable operation will result if the capacitance drops below the minimum specified value. The LP3918 is designed specifically to work with very small ceramic output capacitors. The LDO's on the LP3918 are specifically designed to be used with X7R and X5R type capacitors. With these capacitors selection of the capacitor for the application is dependant on the range of operating conditions and temperature range for that application. (See section on Capacitor Characteristics). It is also recommended that the output capacitor be placed within 1cm from the output pin and returned to a clean ground line. FIGURE 5. Graph Showing A Typical Variation in Capacitance vs DC Bias As an example Figure 5 shows a typical graph showing a comparison of capacitor case sizes in a Capacitance vs DC Bias plot. As shown in the graph, as a result of DC Bias condition the capacitance value may drop below minimum capacitance value given in the recommended capacitor table (0.7F in this case). Note that the graph shows the capacitance out of spec for 0402 case size capacitor at higher bias voltages. It is therefore recommended that the capacitor manufacturers specifications for the nominal value capacitor are consulted for all conditions as some capacitor sizes (e.g 0402) may not be suitable in the actual application. Ceramic capacitors have the lowest ESR values, thus making them best for eliminating high frequency noise. The ESR of a typical 1F ceramic capacitor is in the range of 20m to 40m, and also meets the ESR requirements for stability. The temperature performance of ceramic capacitors varies by type. Capacitor type X7R is specified with a tolerance of 15% over temperature range -55C to +125C. The X5R has similar tolerance over the reduced temperature range -55C to +85C. Most large value ceramic capacitors (<2.2F) are manufactured with Z5U or Y5V temperature characteristics, which results in the capacitance dropping by more than 50% as the temperature goes from 25C to 85C. Therefore X7R is recommended over these other capacitor types in applications where the temperature will change significally above or below 25C. Capacitor Characteristics The LDO's on the LP3918 are designed to work with ceramic capacitors on the input and output to take advantage of the benifits they offer. For capacitance values around 1F, ceramic capacitors give the circuit designer the best design options in terms of low cost and minimal area. For both input and output capacitors careful interpretation of the capacitor specification is required to ensure correct device operation. The capacitor value can change greatly dependant on the conditions of operation and capacitor type. In particular to ensure stability, the output capacitor selection should take account of all the capacitor parameters to ensure that the specification is met within the application. Capacitance value can vary with DC bias conditions as well as temperature and www.national.com 24 LP3918 No-Load Stability The LDO's on the LP3918 will remain stable in regulation with no external load. TABLE 20. LDO Output Capacitors Recommended Specification Symbol Parameter Capacitor Type Typ Limit Min Max Units Co(LDO1) Capacitance X5R. X74 1.0 0.7 2.2 F Co(LDO2) Capacitance X5R. X74 1.0 0.7 2.2 F Co(LDO3) Capacitance X5R. X74 1.0 0.7 2.2 F Co(LDO4) Capacitance X5R. X74 1.0 0.7 2.2 F Co(LDO5) Capacitance X5R. X74 1.0 0.7 2.2 F Co(LDO6) Capacitance X5R. X74 1.0 0.7 2.2 F Co(LDO7) Capacitance X5R. X74 1.0 0.7 2.2 F Note: The capacitor tolerance should be 30% or better over the full temperature range. X7R or X5R capacitors should be used. These specifications are given to ensure that the capacitance remains within these values over all conditions within the application. See Capacitor Characteristics section in Application Information. MISC CONTROL REGISTER TABLE 22. Register Address 8h'1C: Misc BIT NAME 1 APU_TSD _EN 0 PWR_HOLD DELAY Thermal Shutdown The LP3918 has internal limiting for high on-chip temperatures caused by high power dissipation etc. This Thermal Shutdown, TSD, function monitors the temperature with respect to a threshold and results in a device power-down. If the threshold of +160C has been exceeded then the device will power down. Recovery from this TSD event can only be initiated after the chip has cooled below +115C. This device recovery is controlled by the APU_TSD_EN bit (bit 1) in control register MISC, 8h'1C. See Table 22 If the APU_TSD_EN is set low then the device will shutdown requiring a new start up event initiated by PWR_ON, HF_PWR, or CHG_IN. If APU_TSD_EN is set high then the device will power up automatically when the shutdown condition clears. In this case the control register settings are preserved for the device restart. The threshold temperature for the device to clear this TSD event is 115C. This threshold applies for any start up thus the device temperature must be below this threshold to allow a start up event to initiate power up. INTERFACE BUS OVERVIEW The I2C compatible synchronous serial interface provides access to the programmable functions and registers on the device. This protocol uses a two-wire interface for bi-directional communications between the IC's connected to the bus. The two interface lines are the Serial Data Line (SDA), and the Serial Clock Line (SCL). These lines should be connected to a positive supply, via a pull-up resistor of 1.5K, and remain HIGH even when the bus is idle. Every device on the bus is assigned a unique address and acts as either a Master or a Slave depending on whether it generates or receives the serial clock (SCL). TABLE 21. Register Address 8h'0C: Status NAME PWR_ON _TRIG PMU start up is initiated by PWR_ON. 6 HF_PWR _TRIG PMU start up is initiated by HF_PWR. 5 CHG_IN _TRIG PMU start up is initiated by CHG_IN. 1b'0: If PWR_HOLD is low for 35ms the device will shutdown. (Default) 1b'1: If PWR_HOLD is low for 350ms the device will shutdown. I2C Compatible Serial Bus Interface STATUS REGISTER READ ONLY 7 1b' 0: Device will shutdown completely if thermal shutdown occurs. Requires a new start up event to restart the PMU. 1b'1: Device will start up automatically after thermal shutdown condition is removed. (Device tries to keep its internal state.) Bits <7..2> are not used. Further Register Information BIT FUNCTION (if bit = '1') FUNCTION (if bit = '1') DATA TRANSACTIONS One data bit is transferred during each clock pulse. Data is sampled during the high state of the serial clock (SCL). Consequently, throughout the clock's high period, the data should remain stable. Any changes on the SDA line during the high state of the SCL and in the middle of a transaction, aborts the current transaction. New data should be sent during the low SCL state. This protocol permits a single data line to transfer both command/control information and data using the synchronous serial clock. Bits <4..0> are not used. 25 www.national.com LP3918 20211610 FIGURE 7. Start and Stop Conditions 20211613 In addition to the first Start Condition, a repeated Start Condition can be generated in the middle of a transaction. This allows another device to be accessed, or a register read cycle. FIGURE 6. Bit Transfer Each data transaction is composed of a Start Condition, a number of byte transfers (set by the software) and a Stop Condition to terminate the transaction. Every byte written to the SDA bus must be 8 bits long and is transferred with the most significant bit first. After each byte, an Acknowledge signal must follow. The following sections provide further details of this process. ACKNOWLEDGE CYCLE The Acknowledge Cycle consists of two signals: the acknowledge clock pulse the master sends with each byte transferred, and the acknowledge signal sent by the receiving device. The master generates the acknowledge clock pulse on the ninth clock pulse of the byte transfer. The transmitter releases the SDA line (permits it to go high) to allow the receiver to send the acknowledge signal. The receiver must pull down the SDA line during the acknowledge clock pulse and ensure that SDA remains low during the high period of the clock pulse, thus signaling the correct reception of the last data byte and its readiness to receive the next byte. START AND STOP The Master device on the bus always generates the Start and Stop Conditions (control codes). After a Start Condition is generated, the bus is considered busy and it retains this status until a certain time after a Stop Condition is generated. A high-to-low transition of the data line (SDA) while the clock (SCL) is high indicates a Start Condition. A low-to-high transition of the SDA line while the SCL is high indicates a Stop Condition. 20211628 FIGURE 8. Bus Acknowledge Cycle "ACKNOWLEDGE AFTER EVERY BYTE" RULE The master generates an acknowledge clock pulse after each byte transfer. The receiver sends an acknowledge signal after every byte received. There is one exception to the "acknowledge after every byte" rule. When the master is the receiver, it must indicate to the transmitter an end of data by not-acknowledging ("negative acknowledge") the last byte clocked out of the slave. This "negative acknowledge" still includes the acknowledge clock pulse (generated by the master), but the SDA line is not pulled down. (binary 1111110). Before any data is transmitted, the master transmits the address of the slave being addressed. The slave device should send an acknowledge signal on the SDA line, once it recognizes its address. The slave address is the first seven bits after a Start Condition. The direction of the data transfer (R/W) depends on the bit sent after the slave address -- the eighth bit. When the slave address is sent, each device in the system compares this slave address with its own. If there is a match, the device considers itself addressed and sends an acknowledge signal. Depending upon the state of the R/W bit (1:read, 0:write), the device acts as a transmitter or a receiver. ADDRESSING TRANSFER FORMATS Each device on the bus has a unique slave address. The LP3918 operates as a slave device with the address 7h'7E www.national.com 26 * Slave sends data byte from addressed register. If the master device sends acknowledge signal, the control register address will be incremented by one. Slave device sends data byte from addressed register. Read cycle ends when the master does not generate acknowledge signal after data byte and generates stop condition. Address Mode CONTROL REGISTER READ CYCLE * Master device generates a start condition. * Master device sends slave address (7 bits) and the data direction bit (r/w = "0"). * Slave device sends acknowledge signal if the slave address is correct. * Master sends control register address (8 bits). * Slave sends acknowledge signal. * Master device generates repeated start condition. * Master sends the slave address (7 bits) and the data direction bit (r/w = "1"). * Slave sends acknowledge signal if the slave address is correct. Data Read <Start Condition> <Slave Address><r/w = `0'>[Ack] <Register Addr.>[Ack] <Repeated Start Condition> <Slave Address><r/w = `1'>[Ack] [Register Date]<Ack or nAck> ... additional reads from subsequent register address possible <Stop Condition> Data Write <Start Condition> <Slave Address><r/w = `0'>[Ack] <Register Addr.>[Ack] <Register Data>[Ack] ... additional writes to subsequent register address possible <Stop Condition> < > Data from master [ ] Data from slave REGISTER READ AND WRITE DETAIL 20211629 FIGURE 9. Register Write Format 27 www.national.com LP3918 * * CONTROL REGISTER WRITE CYCLE * Master device generates start condition. * Master device sends slave address (7 bits) and the data direction bit (r/w = "0"). * Slave device sends acknowledge signal if the slave address is correct. * Master sends control register address (8 bits). * Slave sends acknowledge signal. * Master sends data byte to be written to the addressed register. * Slave sends acknowledge signal. * If master will send further data bytes the control register address will be incremented by one after acknowledge signal. * Write cycle ends when the master creates stop condition. LP3918 20211630 FIGURE 10. Register Read Format www.national.com 28 LP3918 Physical Dimensions inches (millimeters) unless otherwise noted Thin micro-SMD25 Package NS Package Number MKT-TLA2511A X1 = 2.465mm 0.030mm X2 = 2.465mm 0.030mm X3 = 0.600mm 0.075mm 29 www.national.com LP3918 Battery Charge Management and Regulator Unit Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy PowerWise(R) Solutions www.national.com/powerwise Solutions www.national.com/solutions Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero Temperature Sensors www.national.com/tempsensors SolarMagicTM www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless Analog University(R) www.national.com/AU THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated