DATA SHEE
T
GENERAL PURPOSE CHIP RESISTORS
RC0805 (Pb Free)
5%; 1%
Product specification – Sep 03, 2004 V.2
Product specification
Chip Resistor Surface Mount
2
10
w
ww.yageo.com
Sep 03, 2004 V.2
SERIES
RC 0805 (Pb Free)
Y
YA
AG
GE
EO
O
O
OR
RD
DE
ER
RI
IN
NG
G
C
CO
OD
DE
E
CTC CODE
RC0805 X X X XX XXXX L
(1) (2) (3) (4) (5) (6)
(1) TOLERANCE
F = ±1%
J = ±5%
(2) PACKAGING TYPE
R = Paper/PE taping reel
(3) TEMPERATURE COEFFICIENT OF RESISTANCE
– = Base on spec
(4) TAPING REEL
07 = 7 inch dia. Reel
10 = 10 inch dia. Reel (not preferred)
13 = 13 inch dia. Reel
(5) RESISTANCE VALUE
5R6, 56R, 560R, 5K6, 56K, 22M.
(6) RESISTOR TERMINATIONS
L = Lead free terminations (pure Tin)
ORDERING EXAMPLE
The ordering code of a RC0805 chip resistor, value
56 X with ±1% tolerance, supplied in 7-inch tape reel
is: RC0805FR-0756RL.
NOTE
1. The “L” at the end of the code is only for ordering. On the reel
label, the standard CTC will be mentioned an additional stamp
“LFP”= lead free production.
2. Products with lead in terminations fulfil the same requirements
as mentioned in this datasheet.
3. Products with lead in terminations will be phased out in the
coming months (before July 1st, 2006)
SCOPE
This specification describes RC0805 series chip resistors with lead-free terminations made by thick film process.
ORDERING INFORMATION
Part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and
resistance value.
Product specification
Chip Resistor Surface Mount
3
10
w
ww.yageo.com
Sep 03, 2004 V.2
SERIES
RC 0805 (Pb Free)
DIMENSIONS
TYPE RC0805
L (mm) 2.00 ±0.10
W (mm) 1.25 ±0.10
H (mm) 0.50 ±0.10
I1 (mm) 0.35 ±0.20
I2 (mm) 0.35 ±0.20
Table 1
resistance value. Finally, the two external terminations (pure Tin) are added. See fig. 3.
CONSTRUCTION
The resistors are constructed out of
a high-grade ceramic body. Internal
metal electrodes are added at each
end and connected by a resistive
paste. The composition of the paste
is adjusted to give the approximate
required resistance and laser cutting
of this resistive layer that achieves
tolerance trims the value. The
resistive layer is covered with a
protective coat and printed with the
MARKING
RC0805
E-24 series: 3 digits
First two digits for significant figure and 3rd digit for number of zeros
Both E-24 and E-96 series: 4 digits
First three digits for significant figure and 4th digit for number of zeros
For marking codes, please see EIA-marking code rules in data sheet “Chip resistors instruction”.
Fig. 1 Value=10 KΩ
ynsc001
Fig. 2 Value=10 KΩ
ynsc004
handbook, 4 columns
protective coat
resistor layer
inner electrode
end termination
ceramic substrate
MBE940_a
H
I2
Fig. 3 Chip resistor construction
MBE940_a
protective coat
W
L
I
1
Fig. 4 Chip resistor dimension For dimension see Table 1
Product specification
Chip Resistor Surface Mount
4
10
w
ww.yageo.com
Sep 03, 2004 V.2
SERIES
RC 0805 (Pb Free)
FOOTPRINT AND SOLDERING
PROFILES
For recommended footprint and
soldering profiles, please see the
special data sheet “Chip resistors
mounting”.
ENVIRONMENTAL DATA
For material declaration
information (IMDS-data) of the
products, please see the
separated info “Environmental
data”.
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS RC0805 1/8 W
Operating Temperature Range –55 °C to +155 °C
Maximum Working Voltage 150 V
Maximum Overload Voltage 300 V
Dielectric Withstanding Voltage 300 V
5% (E24) 1 Ω to 22 MΩ
1% (E96) 1 Ω to 10 MΩ
Resistance Range
Zero Ohm Jumper < 0.05 Ω
10 Ω < R ≤ 10 MΩ±100 ppm/°C
Temperature Coefficient R ≤ 10 Ω; R > 10 MΩ±200 ppm/°C
Rated Current 2.0 A
Jumper Criteria Maximum Current 5.0 A
PACKING STYLE AND P
A
CKAGING QUANTITY
PRODUCT TYPE PACKING STYLE REEL DIMENSION QUANTITY PER REEL
RC0805 Paper / PE Taping Reel (R) 7" (178 mm) 5,000 units
10" (254 mm) / not preferred 10,000 units
13" (330 mm) 20,000 units
NOTE
1. For Paper/PE tape and reel specification/dimensions, please see the special data sheet “Packing” document.
Table 3 Packing style and packaging quantity
Table 2
Product specification
Chip Resistor Surface Mount
5
10
w
ww.yageo.com
Sep 03, 2004 V.2
SERIES
RC 0805 (Pb Free)
MRA632
70 100
−55 50
Tamb (°C)
(%Prated)
0
0
50
100
155
Pmax
Fig. 5 Maximum dissipation (Pmax) in percentage of rated power
as a function of the operating ambient temperature (Tamb)
FUNCTIONAL DESCRIPTION
P
PO
OW
WE
ER
R
R
RA
AT
TI
IN
NG
G
RC0805 rated power at 70°C is 1/8 W
RATED VOLTAGE
The DC or AC (rms) continuous working voltage
corresponding to the rated power is determined by
the following formula:
V=√(P X R)
Where
V=Continuous rated DC or
AC (rms) working voltage (V)
P=Rated power (W)
R=Resistance value (X)
10 10 210 310 410 510 610 7
MBD587
104
10
102
103
V
R (Ω)
n
1.2/50 µs
10/700 µs
max
(V)
Fig. 6 Maximum permissible peak pulse voltage without failing to open circuit’ in accordance with DIN IEC 60040 (CO) 533 for type:
RC0805
P
PU
UL
LS
SE
E
L
LO
OA
AD
DI
IN
NG
G
C
CA
AP
PA
AB
BI
IL
LI
IT
TI
IE
ES
S
Product specification
Chip Resistor Surface Mount
6
10
w
ww.yageo.com
Sep 03, 2004 V.2
SERIES
RC 0805 (Pb Free)
10
1
1
MBD588
10
3
1
10
10
2
10
2
10
3
10
4
10
5
10
6
10
1
Pmax
(W)
single pulse
t /t =1000
pi
t (s)
i
Fig. 7 Pulse on a regular basis for type: RC0805; maximum permissible peak pulse powe
r
as a function of pulse duration
f
or single
pulse and repetitive pulse tp/ti = 1000
600
200
0
400
MLB722
10
1
1
10
2
10
3
10
4
10
5
10
6
Vmax
(V)
t (s)
i
Fig. 8 Pulse on a regular basis for type: RC0805; maximum permissible peak pulse voltage as a function of pulse duration
Product specification
Chip Resistor Surface Mount
7
10
w
ww.yageo.com
Sep 03, 2004 V.2
SERIES
RC 0805 (Pb Free)
TESTS AND REQUIREMENTS
TEST TEST METHOD PROCEDURE REQUIREMENTS
At +25/–55 °C and +25/+125 °C Temperature
Coefficient o
f
Resistance
(T.C.R.)
MIL-STD-202F-method 304;
JIS C 5202-4.8
Formula:
T.C.R= ------------------------- × 106 (ppm/°C)
Where
t1=+25 °C or specified room temperature
t2=–55 °C or +125 °C test temperature
R1=resistance at reference temperature in ohms
R2=resistance at test temperature in ohms
Refer to table 3
Thermal Shoc
k
MIL-STD-202F-method 107G;
IEC 60115-1 4.19
At –65 (+0/–10) °C for 2 minutes and at +155
(+10/–0) °C for 2 minutes; 25 cycles
±(0.5%+0.05 Ω) for 1% tol.
±(1.0%+0.05 Ω) for 5% tol.
Low
Temperature
Operation
MIL-R-55342D-Para 4.7.4 At –65 (+0/–5) °C for 1 hour; RCWV applied
for 45 (+5/–0) minutes
±(0.5%+0.05 Ω) for 1% tol .
±(1.0%+0.05 Ω) for 5% tol.
No visible damage
Short Time
Overload
MIL-R-55342D-Para 4.7.5;
IEC 60115-1 4.13
2.5 × RCWV applied for 5 seconds at room
temperature
±(1.0%+0.05 Ω) for 1% tol.
±(2.0%+0.05 Ω) for 5% tol.
No visible damage
Insulation
Resistance
MIL-STD-202F-method 302;
IEC 60115-1 4.6.1.1
RCOV for 1 minute
Type RC0805
Voltage (DC) 300 V
≥10 GΩ
Dielectric
Withstand
Voltage
MIL-STD-202F-method 301;
IEC 60115-1 4.6.1.1
Maximun voltage (Vrms) applied for 1 minute
Type RC0805
Voltage (AC) 300 Vrms
No breakdown or flashover
Resistance to
Soldering
Heat
MIL-STD-202F-method 210C;
IEC 60115-1 4.18
Unmounted chips; 260 ±5 °C for 10 ±1
seconds
±(0.5%+0.05 Ω) for 1% tol.
±(1.0%+0.05 Ω) for 5% tol.
No visible damage
Life MIL-STD-202F-method 108A;
IEC 60115-1 4.25.1
At 70±2 °C for 1,000 hours; RCWV applied for
1.5 hours on and 0.5 hour off
±(1%+0.05 Ω) for 1% tol.
±(3%+0.05 Ω) for 5% tol.
R2–R1
R1(t2–t1)
Table 4 Test condition, procedure and requirements
Product specification
Chip Resistor Surface Mount
8
10
w
ww.yageo.com
Sep 03, 2004 V.2
SERIES
RC 0805 (Pb Free)
TEST TEST METHOD PROCEDURE REQUIREMENTS
Solderabilit
y
MIL-STD-202F-method 208A;
IEC 60115-1 4.17
Solder bath at 245±3 °C
Dipping time: 2±0.5 seconds
Well tinned (≥95% covered)
No visible damage
Bending
Strength
JIS C 5202.6.14;
IEC 60115-1 4.15
Resistors mounted on a 90 mm glass epoxy
resin PCB (FR4)
Bending: 5 mm
±(1.0%+0.05 Ω) for 1% tol.
±(1.0%+0.05 Ω) for 5% tol.
No visible damage
Resistance to
Solvent
MIL-STD-202F-method 215;
IEC 60115-1 4.29
lsopropylalcohol (C3H7OH) or dichloromethane
(CH2Cl2) followed by brushing
No smeared
Noise JIS C 5202 5.9;
IEC 60115-1 4.12
Maximum voltage (Vrms) applied. Resistors range
V
alue
R < 100 Ω 10 dB
100 Ω ≤ R < 1 KΩ 20 dB
1 KΩ ≤ R < 10 KΩ 30 dB
10 KΩ ≤ R < 100 KΩ40 dB
100 KΩ ≤ R < 1 MΩ46 dB
1 MΩ ≤ R ≤ 22 MΩ48 dB
Humidit
y
(steady state)
JIS C 5202 7.5;
IEC 60115-8 4.24.8
1,000 hours; 40±2 °C; 93(+2/–3)% RH
RCWV applied for 1.5 hours on and 0.5 hour of
f
±(0.5%+0.05 Ω) for 1% tol.
±(2.0%+0.05 Ω) for 5% tol.
Leaching EIA/IS 4.13B;
IEC 60115-8 4.18
Solder bath at 260±5 °C
Dipping time: 30±1 seconds
No visible damage
Intermittent
Overload
JIS C 5202 5.8
At room temperature; 2.5 × RCWV applied for
1 second on and 25 seconds off; total 10,000
cycles
±(1.0%+0.05 Ω) for 1% tol.
±(2.0%+0.05 Ω) for 5% tol.
Resistance to
Vibration
On request On request
Moisture
Resistance
Heat
MIL-STD-202F-method 106F;
IEC 60115-1 4.24.2
42 cycles; total 1,000 hours
Shown as figure 9
±(0.5%+0.05Ω) for 1% tol.
±(2.0%+0.05Ω) for 5% tol.
No visible damage
Product specification
Chip Resistor Surface Mount
9
10
w
ww.yageo.com
Sep 03, 2004 V.2
SERIES
RC 0805 (Pb Free)
75
initial drying
24 hours
90 − 98% RH
80 − 98%
RH
temperature
tolerance
±2 °C (±3.6 °F)
unless otherwise
specified
initial measurements
as specified in 2.2
0
STEP1 STEP3STEP2
prior to first
cycle only
STEP4
one cycle 24 hours; repeat as specified in 2.5
voltage applied as specified in 2.4
circulation of conditioning air shall be at a
minimum cubic rate per minute equivalent to
10 times the volume of the chamber
STEP6 STEP7
HBK073
STEP5
51015
end of final cycle;
measurements
as specified in 2.7
optional sub-cycle if specified
(2.3); sub-cycle performed during
any 5 of the first 9 cycles; humidity
uncontrolled during sub-cycle
20
time [h]
temperature
[°C]
25
50
25
0
90 − 98% RH 90 − 98% RH
+10 °C (+18 °F)
−2 °C (−3.6 °F)
80 − 98%
RH
rate of change of temperature is unspecified,
however, specimens shall not be subjected to
radiant heating from chamber conditioning processes
Fig. 9 Moisture resistance test requirements
Product specification
Chip Resistor Surface Mount
10
10
w
ww.yageo.com
Sep 03, 2004 V.2
SERIES
RC 0805 (Pb Free)
REVISION HISTORY
REVISION DATE CHANGE NOTIFICATION DESCRIPTION
Version 2 Sep 03, 2004 - - Test method and procedure updated
- PE tape added (paper tape will be replaced by PE tape)
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Yageo:
RC0805JR-104K7L RC0805FR-103K9L RC0805JR-1368ML RC0805FR-07690KL RC0805JR-07100KS
RC0805FR-07150KS RC0805FR-0722KS RC0805JR-072R2S RC0805JR-0710RS RC0805FR-0775KS RC0805JR-
071K5S RC0805JR-073K3S RC0805FR-07330RS RC0805JR-0722RS RC0805FR-0747KS RC0805FR-07100RS
RC0805FR-07200KS RC0805FR-071KS RC0805JR-074K7S RC0805JR-0722KS RC0805FR-071RS RC0805FR-
07100KS RC0805JR-071RS RC0805JR-072KS RC0805JR-0747RS RC0805JR-070RA RC0805FR-07470RS
RC0805FR-07220RS RC0805JR-071MS RC0805FR-071K5S RC0805FR-072KS RC0805JR-0710KS RC0805JR-
0733RS RC0805FR-0710RS RC0805JR-0747KS RC0805FR-071MS RC0805FR-0715KS RC0805FR-073K3S
RC0805FR-0710KS RC0805FR-0720KS RC0805JR-07220RS RC0805JR-07100RS RC0805JR-07120RS
RC0805JR-072K2S RC0805JR-07470RS RC0805JR-07330RS RC0805FR-07150RS RC0805FR-0727KS
RC0805FR-072K2S RC0805JR-0715KS RC0805FR-074K7S RC0805FR-0747RS RC0805JR-071KS RC0805FR-
0775RS RC0805JR-07220KS RC0805JR-13130RL RC0805FR-1075RL RC0805JR-1033RL RC0805JR-13180KL
RC0805FR-1391KL RC0805FR-102KL RC0805FR-1010RL RC0805FR-13562KL RC0805JR-1315RL RC0805JR-
1047KL RC0805FR-1324K9L RC0805FR-102K05L RC0805FR-10120RL RC0805JR-10220KL RC0805FR-104K75L
RC0805FR-136R8L RC0805JR-1047RL RC0805FR-131K1L RC0805FR-13332KL RC0805FR-1033R2L
RC0805FR-1330K9L RC0805FR-102K21L RC0805FR-13130KL RC0805FR-1327R4L RC0805JR-10560RL
RC0805FR-1327K4L RC0805FR-101RL RC0805FR-1368K1L RC0805JR-134M7L RC0805JR-1330KL RC0805FR-
1356K2L RC0805FR-1047K5L RC0805FR-1082KL RC0805FR-13120RL RC0805JR-10470RL RC0805JR-1033KL