Discontinued in March 2019 FTR-K1 SERIES MINIATURE RELAY 1 POLE - 1 to 2 A (For Signal Switching) MZ Series FEATURES Subminiature size Standard and high sensitivity types available UL, CSA recognized FCC rules and regulations part 68 - Dielectric strength 1,500 V between coil and contacts High reliability-bifurcated contacts available DIL pitch terminals Plastic sealed type RoHS compliant. Please see page 7 for more information PARTNUMBER INFORMATION [Example] MZ (a) F - 12 W HG - K - U (b) (c) (d) (e) (f) (g) (a) Relay type MZ : MZ-Series (b) Dielectric function Nil F : Standard type : High dielectric strength type (c) Coil rated voltage 12 : 1.5.....48 VDC Coil rating table at page 3 Nil D W : 1A single : 2A single (without MZF) : 1A bifurcated (d) (e) Coil type HG HS : Standard type (without MZ-D) (450-500mW) : High sensitivity type (without MZF / MZ-D) (190-270mW) (f) Enclosure Nil K : Flux free type : Plastic sealed type (g) UL, CSA standard Nil U : Non UL, CSA approved : UL, CSA approved 1 FTR-K1MZ SERIES SERIES Discontinued in March 2019 n SPECIFICATION Item Standard type High sensitivity type Single MZ - ( ) D Contact Data Life Coil Data Timing Data Insulation Single Bifurcated MZ-( ) WHG MZ - ( ) HS MZ-( ) WHS Configuration 1 form C (SPDT) Material Gold-overlay silver nickel Resistance (initial) Max. 100 m at 6 VDC, 1A Contact rating (resistive) 2A, 24VDC 1A, 120VAC Max. carrying current 2A Max. switching voltage 120VAC, 60VDC Max. switching power 120VA / 48W 60VA / 24W Max. switching current 2A 1A Min. switching load* 1mA, 1 VDC Capacitance (at 10 MHz) Approximately 0.8 pF (between open contacts, adjacent contacts) Approximately 7.5 pF (between coil and contacts) Mechanical Min. 20 x 106 operations Electrical 1A, 120VAC: min. 100 x 103 ops. 2A, 24VDC: min. 200 x 103 ops. min. Rated power (at 20 C) 450 - 500 mW 190 - 270 mW Operate power (at 20 C) 220 - 250 mW 100 - 130 mW Operating temperature range -30 C to +55 C (no frost) -30 C to +75 C Operate (at nominal voltage) Max. 6 ms Release (at nominal voltage) Max. 3 ms Isolation (initial) Min. 100M at 500VDC Surge strength Vibration resistance Shock Weight Gold overlay silver-palladium 1A, 24VDC 0.5A, 120VAC 0.1mA, 100 mVDC 1mA, 1VDC 0.1mA, 100 mVDC 0.5A, 120VAC: min. 200 x 103 operations 1A, 24VAC: min. 500 x 103 operations Open contacts Standard: 500VAC, 1min. High Isolation: 1,000VAC, 1min. Contacts to coil Standard: 500VAC, 1min. High Isolation: 1,500VAC, 1min. Coil to contacts 1,500V / 1 x 40s standard wave Misoperation 10 to 55Hz double amplitude 3.28 mm Endurance 10 to 55Hz double amplitude 3.28 mm Misoperation Min. 100m/s (11 1ms) Endurance Min. 1,000m/s (6 1ms) Dielectric strength Other MZ- ( ) HG Bifurcated Approximately 3.5 g * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2 FTR-K1MZ SERIES SERIES Discontinued in March 2019 COIL RATING n Standard type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * 1.5 1.5 5 1.05 0.08 3 3 20 2.1 0.15 4.5 4.5 45 3.15 0.23 5 5 56 3.5 0.25 6 6 80 4.2 0.3 9 9 180 6.3 0.45 12 12 320 8.4 0.6 18 18 720 12.6 0.9 24 24 1,280 16.8 1.2 48 48 4,600 33.6 2.4 500 Rated Power (mW) 450 High sensitive type Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- 10% (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * Rated Power (mW) 1.5 1.5 12 1.05 0.08 190 3 3 45 2.1 0.15 4.5 4.5 100 3.15 0.23 5 5 120 3.5 0.25 6 6 180 4.2 0.3 9 9 400 6.3 0.45 12 12 700 8.4 0.6 15 15 1,100 10.5 0.75 18 18 1,600 12.6 0.9 24 24 2,800 16.8 1.2 48 48 8,500 33.6 2.4 200 270 Note: All values in the table are valid for 20C and zero contact current. * Specified operate values are valid for pulse wave voltage. n SAFETY STANDARDS Type Compliance Contact rating UL UL 508, UL 60950-1 Flammability: UL 94-V0 (plastics) E 45026 CSA C22.2 No. 14 LR 35579 [1A] 0.5A, 120VAC (resistive) 1A, 24VDC (resistive) [2A] 1A, 120VAC (resistive) 2A, 30VDC (resistive) 3 Discontinued in March 2019 n FTR-K1MZ SERIES SERIES CHARACTERISTIC DATA n REFERENCE DATA 4 Discontinued in March 2019 FTR-K1MZ SERIES SERIES 5 Discontinued Discontinuedin March 2019 FTR-K1 SERIES MZ SERIES DIMENSIONS Dimensions Schematics (BOTTOM VIEW) PC board mounting hole layout (BOTTOM VIEW) MZ (F) type (Flux free type) MZ (F)-K type (Plastic sealed type) Unit: mm Note: This datasheet provide only + tolerance for outer dimensions. 6 Discontinued Discontinuedin March 2019 FTR-K1MZ SERIES SERIES RoHS Compliance and Lead Free Information 1. General Information All relays produced by Fujitsu Components are compliant with RoHS directive 2011/65/EU including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives. As per Annex III of directive 2011/65/EU. All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: http://www.fujitsu.com/downloads/MICRO/fcai/relays/lead-free-letter.pdf Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Condition Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder Condition: Pre-heating: maximum 120C within 90 sec. Soldering: dip within 5 sec. at 255C 5C solder bath Relay must be cooled by air immediately after soldering Solder by Soldering Iron: Soldering Iron Temperature: Duration: 30-60W maximum 350-360C maximum 3 sec. 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 7 FTR-K1MZ SERIES SERIES Discontinued in March 2019 Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Shinagawa Seaside Park Tower 19F, 12-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo,140-0002, Japan Tel: (81-3) 3450-1681 Fax: (81-3) 3474-2385 Email: fcl-contact@cs.jp.fujitsu.com Web: www.fcl.fujitsu.com Europe Fujitsu Components Europe B.V. Diamantlaan 25 2132 WV Hoofddorp Netherlands Tel: (31-23) 5560910 Fax: (31-23) 5560950 Email: info@fceu.fujitsu.com Web: emea.fujitsu.com/components/ North and South America Fujitsu Components America, Inc. 2290 North 1st Street, Suite 212 San Jose, CA 95131, USA Tel: (1-408) 745-4900 Fax: (1-408) 745-4970 Email: components@us.fujitsu.com Web: http://us.fujitsu.com/components Asia Pacific Fujitsu Components Asia Ltd. 102E Pasir Panjang Road #01-01 Citilink Warehouse Complex Singapore 118529 Tel: (65) 6375-8560 Fax: (65) 6273-3021 Email: fcal@fcal.fujitsu.com Web: http://www.fujitsu.com/sg/services/micro/components/ (c)2014 Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users' own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. August 04, 2014 8