User's Guide SLVU304C - April 2009 - Revised November 2011 TPS23754EVM-383 EVM: Evaluation Module for TPS23754 This User's Guide describes the TPS23754 EVM (TPS23754EVM-383). TPS23754EVM-383 contains evaluation and reference circuitry for the TPS23754. The TPS23754 is an IEEE 802.3at compliant powered device (PD) controller and power supply controller optimized for isolated converter topologies. TPS23754EVM-383 is targeted at 25W, active clamp, forward converter applications. 1 2 3 4 5 6 7 8 Contents Description ................................................................................................................... 2 1.1 Features ............................................................................................................. 2 1.2 Applications ......................................................................................................... 2 Electrical Specifications .................................................................................................... 2 Schematic .................................................................................................................... 3 General Configuration and Description .................................................................................. 4 4.1 Physical Access .................................................................................................... 4 Test Setup ................................................................................................................... 5 TPS23754EVM-383 Typical Performance Data ........................................................................ 5 6.1 12V DC/DC Efficiency ............................................................................................. 5 6.2 TPS23754EVM-383 Conducted Emissions ..................................................................... 6 EVM Assembly Drawings and Layout Guidelines ...................................................................... 6 7.1 PCB Drawings ...................................................................................................... 6 7.2 Layout Guidelines .................................................................................................. 8 7.3 EMI Containment ................................................................................................... 9 Bill of Materials ............................................................................................................. 10 List of Figures 1 TPS23754EVM-383 Schematic ........................................................................................... 3 2 Typical TPS23754EVM-383 Test Setup ................................................................................. 5 3 TPS23754EVM-383 Efficiency With 12V Output 4 5 6 7 8 ....................................................................... TPS23754EVM-383 Conducted Emissions.............................................................................. Top Side Layout/Routing ................................................................................................... Layer Two Routing .......................................................................................................... Layer Three Routing ........................................................................................................ Bottom Side Placement/Routing .......................................................................................... 5 6 6 7 7 8 List of Tables 1 TPS23754EVM-383 Electrical and Performance Specifications ...................................................... 2 2 Connector Functionality .................................................................................................... 4 3 Test Points ................................................................................................................... 4 4 TPS23754EVM-383 Bill of Materials SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback ................................................................................... TPS23754EVM-383 EVM: Evaluation Module for TPS23754 Copyright (c) 2009-2011, Texas Instruments Incorporated 10 1 Description 1 www.ti.com Description TPS23754EVM-383 will allow reference circuitry evaluation of the TPS23754. It contains input and output power connectors and an array of on board test points for circuit evaluation. A synchronous flyback, 5V, 25W EVM is also available, see SLVU301. 1.1 Features * 1.2 Applications * * * 2 Efficient, general market design - Self driven, synchronous rectified secondary - 25w output power from power over ethernet (POE), 30W output power from a 48V adapter - Operates from either POE or external adaptors (48V) - 12V output voltage Voice over Internet Protocol - IP telephones Wireless LAN - Wireless Access Points Security - Wired IP cameras Electrical Specifications Table 1. TPS23754EVM-383 Electrical and Performance Specifications Parameter Condition Min Typ Max Units Power Interface Input voltage Applied to the power pins of connectors J1 or J3 Operating Voltage After start up Input UVLO 0 57 V 30 57 V Rising input voltage 36 V Falling input voltage 30 Detection voltage At device terminals 1.6 10 Classification voltage At device terminals 10 23 V Classification current Rclass = 63.4 36 44 mA Inrush current-limit 100 180 mA Operating current-limit 850 1100 mA V DC/DC Converter Output voltage 33 V Vin 57 V, ILOAD ILOAD (max) 12 V output Output current 33 V Vin 57 V 12 V output Output ripple voltage, peak-to-peak Vin = 44 V, ILOAD = 2.5 A 12 V output 100 Efficiency, end-to-end 12 V output 87% Vin = 44 V, ILOAD = 2.5 A Switching frequency 2 V 2.5 225 TPS23754EVM-383 EVM: Evaluation Module for TPS23754 Amps mV 275 kHz SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated Schematic www.ti.com Schematic T1 1 3 Figure 1. TPS23754EVM-383 Schematic SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback TPS23754EVM-383 EVM: Evaluation Module for TPS23754 Copyright (c) 2009-2011, Texas Instruments Incorporated 3 General Configuration and Description www.ti.com 4 General Configuration and Description 4.1 Physical Access Table 2 lists the TPS23754EVM-383 connector functionality and Table 3 describes the test point availability. Table 2. Connector Functionality Connector Label Description J1 ADAPTER External adapter input. J7 (low side) and J8 (high side) can select weather the adapter is at the PD controller input (VDD to VSS) or at the converter input (VDD1 to RTN). J6 is used to select PPD or APD function. J2 VOUT Output voltage connector J3 DATA + PoE POWER Ethernet power input connector. Contains Ethernet transformer and cable terminations J4 DATA PORT Ethernet data port connector J5 EGND Earth GND connection Table 3. Test Points Test Point 4 Color Label Description TP3, TP17, TP18 BLK GND Secondary side (output) grounds (GND) TP5 RED VC TP6 ORG DRAIN TP10 BLK VSS POE input, low side TP12, TP16 BLK RTN DC/DC converter return TP14 ORG LOOP Can be used with TP13 for overall feedback loop measurements. TP13 RED VOUT DC/DC converter output voltage. TP15 WHT CTL Control loop input to the pulse width modulator TP9 WHT RCS DC/DC converter primary side switching MOSFET current sense (resistor side). TP11 RED VB TP8 WHT GATE Gate drive for the primary side switching MOSFET TP7 WHT GAT2 Gate drive for the primary side active clamp MOSFET TP4 RED PVDD1 TP23 WHT T2P Type 2 PSE output from TPS23754 TP1 WHT PPD Connected to PPD pin of TPS23754 TP2 WHT APD Connected to APD pin of TPS23754 TP20 RED P78 Pair 7,8 TP21 ORG P12 Pair 1,2 TP19 ORG P45 Pair 4,5 TP22 RED P36 Pair 3,6 D21 GRN T2P Type 2 PSE indicator. Remove the shunt on J9 to inhibit the T2P indicator. D12 RED CL1 N/A DC/DC converter bias supply Drain terminal of the primary side switching MOSFET Bias voltage regulator Transformer primary high side. POWER ON Output power indicator. Remove the shunt on J10 to inhibit the output power indicator. CL1 Provides a connection between VDD and VDD1 shorting out D3. Removing the short at CL1 allows certain power source priority schemes to be tested. TPS23754EVM-383 EVM: Evaluation Module for TPS23754 SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated Test Setup www.ti.com 5 Test Setup Figure 2 shows a typical test setup for TPS23754EVM-383. Input voltage can be applied as described in Table 2. AUX Power Source J1 PSE Or Power Supply (Ethernet Cable ) + J3 DUT TPS 23754 EVM -383 VOUT J2 GND J4 Data to PHY (Ethernet Cable ) R LOAD Figure 2. Typical TPS23754EVM-383 Test Setup 6 TPS23754EVM-383 Typical Performance Data 6.1 12V DC/DC Efficiency Figure 3 illustrates three different 48VDC input efficiency plots: 1. PoE, 48V from J3 2. Converter only 48V 3. Adapter 48V from J1 95 90 Adapter 48V 85 Converter 48V PoE 48V Efficiency - % 80 75 70 65 60 55 50 0 0.5 1 1.5 IO - Output Current - A 2 2.5 Figure 3. TPS23754EVM-383 Efficiency With 12V Output SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback TPS23754EVM-383 EVM: Evaluation Module for TPS23754 Copyright (c) 2009-2011, Texas Instruments Incorporated 5 EVM Assembly Drawings and Layout Guidelines 6.2 www.ti.com TPS23754EVM-383 Conducted Emissions HPA383 (TPS23754PWP) 12V / 2A Output Class B Quasi-Peak Limit Class B Average Limit Figure 4. TPS23754EVM-383 Conducted Emissions 7 EVM Assembly Drawings and Layout Guidelines 7.1 PCB Drawings The following figure shows component placement and layout. Figure 5. Top Side Layout/Routing 6 TPS23754EVM-383 EVM: Evaluation Module for TPS23754 SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated EVM Assembly Drawings and Layout Guidelines www.ti.com Figure 6. Layer Two Routing Figure 7. Layer Three Routing SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback TPS23754EVM-383 EVM: Evaluation Module for TPS23754 Copyright (c) 2009-2011, Texas Instruments Incorporated 7 EVM Assembly Drawings and Layout Guidelines www.ti.com Figure 8. Bottom Side Placement/Routing 7.2 Layout Guidelines The layout of the PoE front end should follow power and EMI/ESD best practice guidelines. A basic set of recommendations include: * Parts placement must be driven by power flow in a point-to-point manner; RJ-45, Ethernet transformer, diode bridges, TVS and 0.1-F capacitor, and TPS23754 converter input bulk capacitor. * All leads should be as short as possible with wide power traces and paired signal and return. * There should not be any crossovers of signals from one part of the flow to another. * Spacing consistent with safety standards like IEC60950 must be observed between the 48-V input voltage rails and between the input and an isolated converter output. * The TPS23754 should be located over split, local ground planes referenced to VSS for the PoE input and to RTN for the converter. Whereas the PoE side may operate without a ground plane, the converter side must have one. Logic ground and power layers should not be present under the Ethernet input or the converter primary side. * Large copper fills and traces should be used on SMT power-dissipating devices, and wide traces or overlay copper fills should be used in the power path. The DC/DC Converter layout can benefit from basic rules such as: * Pair signals to reduce emissions and noise, especially the paths that carry high-current pulses which include the power semiconductors and magnetics. * Minimize trace length of high current, power semiconductors, and magnetic components. * Where possible, use vertical pairing. * Use the ground plane for the switching currents carefully. * Keep the high-current and high-voltage switching away from low-level sensing circuits including those outside the power supply. * Pay special attention to spacing around the high-voltage sections of the converter. 8 TPS23754EVM-383 EVM: Evaluation Module for TPS23754 SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback Copyright (c) 2009-2011, Texas Instruments Incorporated EVM Assembly Drawings and Layout Guidelines www.ti.com 7.3 EMI Containment * * * * * * * * * * * * * * * * * * * * * Use compact loops for dv/dt and di/dt circuit paths (power loops and gate drives) Use minimal, yet thermally adequate, copper areas for heat sinking of components tied to switching nodes (minimize exposed radiating surface). Use copper ground planes (possible stitching) and top layer copper floods (surround circuitry with ground floods) Use 4 layer PCB if economically feasible (for better grounding) Minimize the amount of copper area associated with input traces (to minimize radiated pickup) Hide copper associated with switching nodes under shielded magnetics where possible Heat sink the "quiet side" of components instead of the "switching side" where possible (like the output side of inductor) Use Bob Smith terminations, Bob Smith EFT capacitor, and Bob Smith plane Use Bob Smith plane as ground shield on input side of PCB (creating a phantom or literal earth ground) Use LC filter at DC/DC input Dampen high frequency ringing on all switching nodes if present (allow for possible snubbers) Control rise times with gate drive resistors and possibly snubbers Switching frequency considerations Use of EMI bridge capacitor across isolation boundary (isolated topologies) Observe the polarity dot on inductors (embed noisy end) Use of ferrite beads on input (allow for possible use of beads or 0 ohm resistors) Maintain physical separation between input-related circuitry and power circuitry (use ferrite beads as boundary line) Balance efficiency vs. Acceptable noise margin Possible use of common-mode inductors Possible use of integrated RJ-45 jacks (shielded with internal transformer and Bob Smith terminations) End-product enclosure considerations (shielding) SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback TPS23754EVM-383 EVM: Evaluation Module for TPS23754 Copyright (c) 2009-2011, Texas Instruments Incorporated 9 Bill of Materials 8 www.ti.com Bill of Materials Table 4. TPS23754EVM-383 Bill of Materials Count 10 RefDes Value Description Size Part Number MFR 1 C1 0.047 F Capacitor, Ceramic, 250V, X7R, 10% 1206 Std Std 3 C10, C23, C24 0.1 F Capacitor, Ceramic, 100V, X7R, 10% 0805 Std Std 1 C11 100 F Capacitor, Aluminum, 16V, 20%, FK Series 0.217 x 0.169 EEVFK1C101P Panasonic 1 C12 22 F Capacitor, Ceramic, 16-V, X7R, 20% 1210 C3225X7R1C226MT TDK 1 C13 1.0 F Capacitor, Ceramic, 25V, X7R, 10% 0805 Std Std 1 C14 22 F Capacitor, Aluminum, 25V, 20% 5x5.8mm EEVFK1E220R Panasonic 1 C15 47 pF Capacitor, Ceramic, 50V, X7R, 10% 0603 Std Std 1 C16 1.0 F Capacitor, Ceramic, 16V, X7R, 10% 0603 Std Std 1 C17 22 nF Capacitor, Ceramic, 50V, X7R, 10% 0603 Std Std 1 C18 10 pF Capacitor, Ceramic, 50V, C0G, 5% 0603 Std Std 1 C19 15 nF Capacitor, Ceramic, 50V, X7R, 10% 0603 Std Std 1 C2 1 F Capacitor, Ceramic, 16V, X7R, 20% 0603 C1608X7R1C105M TDK 1 C20 1 F Capacitor, Ceramic, 16V, X7R, 10% 0805 Std Std 1 C21 1000 pF Capacitor, Ceramic, 2kV, X7R, 10% 1210 Std TDK 1 C25 10 nF Capacitor, Ceramic, 100V, X7R, 10% 0603 Std Std 1 C3 2200 pF Capacitor, Ceramic, 2KV, X7R, 10% 1812 C4532X7R3D222K TDK 2 C4, C7 1 F Capacitor, Ceramic, 100V, X7R, 10% 1210 Std Std 2 C5, C6 22 F Capacitor, Aluminum, 100V, 20% 8x10.2mm EEVFK2A220P Panasonic 1 C8 100 pF Capacitor, Ceramic, 50V, X7R, 10% 0603 C1608X7R1H101K TDK 2 C9, C22 1 nF Capacitor, Ceramic, 100V, X7R, 10% 0805 Std Std 1 CL1 NA Current Loop, 0.025 holes 0.120 x 0.075 inch NA NA 5 D1, D4, D5, D7, D8 BAS16 Diode, Switching, 75V, 200mA SOT23 BAS16LT1 Vishay-Liteon 1 D11 BAV99 Diode, Dual Ultra Fast, Series, 200-mA, 70-V SOT23 BAV99 Fairchild 1 D12 RED Diode, LED, RED, 2.0-V, 850-mcd, SM 1210 LTST-C930KRKT LITE-ON INC 10 D2, D3, D13-D20 B1100 Diode, Schottky, 1A, 100V SMA B1100 Diodes, Inc 1 D21 GREEN Diode, LED, GRN, 2.0-V, 650-mcd,SM 1210 LTST-C930KGKT LITE-ON INC 2 D6, D22 SMAJ58A Diode, TVS, 58-V, 1W SMA SMAJ58A Diodes Inc. 2 D9, D10 12V Diode, Zener, 12-V SOT23 BZX84C12LT1 ON Semiconductor 4 FB1-FB4, 500 Bead, Ferrite, 2000mA, 60m-ohm 1206 MI1206L501R-10 Steward 3 J1, J2, J5 ED1514 Terminal Block, 2-pin, 6-A, 3.5mm 0.27 x 0.25 ED1514 OST 1 J3 7499511001 Connector, RJ45, PoE+ Enabled, 1000 Base-T 0.670 x 1.300 inch 7499511001 Wuerth Electronics 1 J4 5556416-1 Connector, Jack Modular, Vertical, Pos. 0.655 x 0.615 inch 5556416-1 AMP SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback TPS23754EVM-383 EVM: Evaluation Module for TPS23754 Copyright (c) 2009-2011, Texas Instruments Incorporated Bill of Materials www.ti.com Table 4. TPS23754EVM-383 Bill of Materials (continued) Count RefDes Value Description Part Number MFR 3 J6-J8 PTC36SAAN Header, Male 3-pin, 100mil spacing, (36-pin strip) 0.100 inch x 3 Size PTC36SAAN Sullins 2 J9, J10 PTC36SAAN Header, Male 2-pin, 100mil spacing, (36-pin strip) 0.100 inch x 2 PTC36SAAN Sullins 1 L1 3.3 H Inductor, SMT, 2.15A, 35 milliohm or 1.53A, 32 milliohm 5.1x5.1mm 744043003 or MSS5131-332MX Wurth or Coilcraft 1 L2 22 H Inductor, SMT, 4.1A, 43 milliohm or 3.8A, 33 milliohm 0.492 sq" 744770122 or P1173.223T Wurth or Pulse 1 L3 1 mH Inductor, SMT, 100mA, 16.3 Ohms 0.169 x 0.169 inch LPS4414-105MLC Coilcraft 1 Q1 Si2325DS MOSFET,P-ch, -150 V, 690-mA, 1.2 Ohms SOT-23 Si2325DS Vishay 2 Q2, Q4 MMBTA06 Bipolar, NPN, 80V, 500mA SOT23 MMBTA06LT1 ON Semiconductor 1 Q3 Si4850EY MOSFET, Nch, 60V, 8.5A, 22milliohm SO8 Si4850EY Vishay 1 Q5 Si7852DP MOSFET, Nchan, 80V, 12A, 16-milliohm PWRPAK-S08 Si7852DP Vishay 1 Q6 Si4848DY MOSFET, N-ch, 150V, 3.7A, 85 milliohm SO8 Si4848DY Vishay 1 R1 100K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R11 80.6K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R12 63.4K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R13 63.4 Resistor, Chip, 1/10W, 1% 0805 Std Std 1 R14 10 Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R15 1K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R16 0.12 Resistor, Chip, 1/4W, 1% 1206 ERJ-8RQFR12V Panasonic ECG 1 R17 348 Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R18 49.9 Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R2 6.49K Resistor, Chip, 1/10-W, 1% 0805 Std Std 1 R20 2.87K Resistor, Chip, 1/10-W, 1% 0805 Std Std 1 R21 1.5K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R23 41.2K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R25 11.0K Resistor, Chip, 1/16W, 1% 0603 Std Std 4 R26-R29 75 Resistor, Chip, 1/16W, 1% 0603 Std Std 3 R3, R19, R24 10K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R4 4.02K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R22 2.49K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R5 8.87K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 R6 0 Resistor, Chip, 1/16W, 1% 0603 Std Std 2 R7, R10 2K Resistor, Chip, 1/4W, 5% 1210 Std Std 1 R8 24.9K Resistor, Chip, 1/16W, 1% 0603 Std Std SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback TPS23754EVM-383 EVM: Evaluation Module for TPS23754 Copyright (c) 2009-2011, Texas Instruments Incorporated 11 Bill of Materials www.ti.com Table 4. TPS23754EVM-383 Bill of Materials (continued) Count RefDes Value Description Size Part Number MFR 1 R9 69.8K Resistor, Chip, 1/16W, 1% 0603 Std Std 1 T1 750311320 or PA2649NL or 835-01064FC Transformer, forward, 100 H, 12V, 2.5A 0.524 x 0.685 inch 750311320 or PA2649NL or 835-01064FC Wurth or Pulse or E&E Magnetics 7 TP1, TP2, TP7-TP9, TP15, TP23 5012 Test Point, White, Thru Hole 0.125 x 0.125 inch 5012 Keystone 6 TP3, TP10, TP12, TP16-TP18 5011 Test Point, Black, Thru Hole 0.125 x 0.125 inch 5011 Keystone 6 TP4, TP5, TP11, TP13, TP20, TP22 5010 Test Point, Red, Thru Hole 0.125 x 0.125 inch 5010 Keystone 4 TP6, TP14, TP19, TP21 5013 Test Point, Orange, Thru Hole 0.125 x 0.125 inch 5013 Keystone 1 U1 TPS23754PWP IC, IEEE 802.3at PoE Interface and Isolated Converter Controller PWP20 TPS23754PWP TI 1 U2 FOD817AS IC, Optocoupler, 6-V, 80-160% CTR SMT-4PDIP FOD817AS Fairchild 1 U3 TL431ACDBVR IC, Shunt Regulator, 2.49-V ref, 36-V, 10-mA, 1% SOT23-5 TL431ACDBVR TI Bumpons 2566 SPC 929950-00 3M 4 5 12 -- Shunt, Black 100-mil SLVU304C - April 2009 - Revised November 2011 Submit Documentation Feedback TPS23754EVM-383 EVM: Evaluation Module for TPS23754 Copyright (c) 2009-2011, Texas Instruments Incorporated Evaluation Board/Kit Important Notice Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental measures typically found in end products that incorporate such semiconductor components or circuit boards. This evaluation board/kit does not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives. Should this evaluation board/kit not meet the specifications indicated in the User's Guide, the board/kit may be returned within 30 days from the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims arising from the handling or use of the goods. Due to the open construction of the product, it is the user's responsibility to take any and all appropriate precautions with regard to electrostatic discharge. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety programs, please contact the TI application engineer or visit www.ti.com/esh. No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or combination in which such TI products or services might be or are used. FCC Warning This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are designed to provide reasonable protection against radio frequency interference. Operation of this equipment in other environments may cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may be required to correct this interference. EVM Warnings and Restrictions It is important to operate this EVM within the input voltage range of 0 V to 57 V and the output voltage range of 10 V to 15 V . Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power. Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures greater than 80C. The EVM is designed to operate properly with certain components above 80C as long as the input and output ranges are maintained. These components include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of devices can be identified using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during operation, please be aware that these devices may be very warm to the touch. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: TPS23754EVM-383