SKY77148 - Skyworks Solutions, Inc.

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103018B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 12, 2006 1

DATA SHEET

SKY77148 PA Module for CDMA2000 (450–460 MHz)

Applications

• Digital cellular (CDMA2000)

• Wireless Local Loop (WLL)

Features

• Low voltage positive bias

supply

- (3.2 V to 4.2 V)

• Good linearity

• High efficiency across wide

dynamic range

• Dual-mode operation

• 7-pin package

- 6 mm x 6 mm x 1.5 mm

• Power down control

• Low power state control

• CDMA2000

Skyworks offers lead

(Pb)-free "environmentally

friendly" packaging

that is RoHS compliant

(European Parliament

for the Restriction of

Hazardous Substances).

Description

The SKY77148 Power Amplifier Module (PAM) is a fully matched 7-pin surface mount module

developed for Code Division Multiple Access (CDMA2000) handset and Wireless Local Loop

applications. This small and efficient power amplifier packs full coverage of the 450–460 MHz

bandwidth into a single compact package. The device meets the stringent CDMA2000 linearity

requirements to and exceeding 29 dBm output power. A low current pin (VCONT) provides improved

efficiency for the low RF power range of operation.

The single Gallium Arsenide (GaAs) Microwave Monolithic Integrated Circuit (MMIC) contains all active

circuitry within the module, which includes on-board bias circuitry as well as input and interstage

matching circuits. Output match into a 50 Ω load is realized off-chip within the module package to

optimize efficiency and power performance. This device is manufactured with Skyworks’ GaAs

Heterojunction Bipolar Transistor (HBT) process that provides for all positive voltage DC supply

operation while maintaining high efficiency and good linearity. Primary bias to the SKY77148 is

supplied directly from a three-cell Ni-Cd, a single-cell Li-Ion, or other suitable battery with a rated

output in the 3.2 to 4.2 volt range. Setting the voltage on the low current reference pin to zero volts

accomplishes power down. No external supply side switch is needed as typical “off” leakage is a few

microamperes with full primary voltage from the battery.

VCC1 (1)

VCC2 (5)

VREF (3)

RF IN (2) (6) RF OUT

GND (7)

VCONT (4)

Driver

Stage Bias

Input Match InterStage

Match PA Output Match

Power

Stage Bias

103018_001

MMIC MODULE

Figure 1. Functional Block Diagram

DATA SHEET • SKY77148 PA MODULE FOR CDMA2000 (450–460 MHZ)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

2 May 12, 2006 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 103018B

Electrical Specifications

The following tables list the electrical characteristics of the

SKY77148 Power Amplifier Module. Table 1 lists the absolute

maximum ratings while Table 2 shows the recommended

operating conditions to achieve the performance characteristics

listed in Table 4. A truth table for the power ranges is shown in

Table 3.

Table 1. Absolute Maximum Ratings 1

Parameter Symbol Minimum Nominal Maximum Unit

RF Input Power PIN — 0.0 6.0 dBm

Supply Voltage VCC — 3.4 6.0 Volts

Reference Voltage VREF — 3.0 3.1 Volts

Operating TC –30 +25 +110

Case Temperature 2

Storage TSTG –55 — +125

°C

1 No damage assuming only one parameter at a time is set at limit with all other parameters set at or below nominal value.

2 Case Operating Temperature refers to the temperature of the GROUND PAD at the underside of the package.

Table 2. Recommended Operating Conditions

Parameter Symbol Minimum Nominal Maximum Unit

Supply Voltage VCC 3.2 3.4 4.2 Volts

Reference Voltage VREF 2.95 3.0 3.05 Volts

LOW VCONT 2.5 — 3.0

Control voltage

HIGH VCONT 0.0 — 0.5

Volts

Operating Frequency FO 450.0 455 460 MHz

Case Operating Temperature TC –30 +25 +85 °C

Table 3. Power Range Truth Table

Power Mode VREF VCONT Range

High Power 3.0 V 0.0–0.5 V 16 dBm to 29 dBm

Low Power 3.0 V 2.5–3.0 V ≤ 16 dBm

Shut Down 0.0 V 0.0 V —

PA MODULE FOR CDMA2000 (450–460 MHZ) DATA SHEET • SKY77148

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103018B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 12, 2006 3

Table 4. Electrical Specifications for CDMA Nominal Operating Conditions 1

Characteristics Symbol Condition Minimum Typical Maximum Unit

GLOW VCONT ≥ 2.5 V

PO = 16 dBm 24.5 26.5 28.2

Gain conditions Digital Mode

GHIGH VCONT ≤ 0.5 V

PO = 29 dBm 29.0 31.0 32.5

PAELOW VCONT ≥ 2.5 V

PO = 16 dBm 7.0 8.0 —

Power Added Efficiency Digital Mode

PAEHIGH VCONT ≤ 0.5 V

PO = 29 dBm 35.0 38.0 —

ICC_LOW PO = 16 dBm — 155 175

Total Supply Current

ICC_HIGH PO = 29 dBm — 650 705

IQ_LOW VCONT ≥ 2.5 V 50 65 75

Quiescent Current

IQ_HIGH VCONT ≤ 0.5 V 70 90 105

Reference Current IREF — 0.75 1.0 mA

Control Current ICONT VCONT = 2.5 V — .95 1.2 µA

Total Supply Current in Power-down Mode IPD VCC = 3.4 V

VREF = 0 V — 2.0 4.5 µA

ACP1LOW VCONT ≥ 2.5 V

PO ≤ 16 dBm — –47.0 –45.5

885 kHz offset

ACP1HIGH VCONT ≤ 0.5 V

PO ≤ 29 dBm — –50.0 –46.5

ACP2LOW VCONT ≥ 2.5 V

PO ≤ 16 dBm — –65.0 –58.0

Adjacent Channel Power 2,3

1.98 MHz offset

ACP2HIGH VCONT ≤ 0.5 V

PO ≤ 29 dBm — –59.0 –57.0

dBc

Second FO2 PO ≤ 29 dBm — –45.0 –35.0

Harmonic Suppression

Third FO3 PO ≤ 29 dBm — –55.0 –40.0

dBc

Noise Power in RX Band 460-470 MHz RxBN PO ≤ 29 dBm — –129 –127 dBm/Hz

Noise Figure NF — 5.0 5.5 dB

Input Voltage Standing Wave Ratio VSWR — 1.6:1 2.0:1 —

Stability (Spurious output) S 5:1 VSWR all phases — — –65.0 dBc

Ruggedness—No damage 4 Ru PO ≤ 29 dBm 10:1 — — VSWR

1 Unless otherwise specified:

VCC = +3.4 V,

VREF = +3.0 V,

Freq = 455 MHz,

TC = 25 °C

2 ACP is specified per CDMA2000 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW.

3 CDMA2000 is configured as DCCH = 9600, SCHO = 9600, PCH (Walsh 0) = –3.75 dB, and Peak-to-Average Ratio (CCDF = 1%) = 4.5 dB.

4 All phases, time = 10 seconds.

DATA SHEET • SKY77148 PA MODULE FOR CDMA2000 (450–460 MHZ)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

4 May 12, 2006 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 103018B

Table 5. Electrical Specifications for CDMA Recommended Operating Conditions 1

Characteristics Symbol Condition Minimum Maximum Unit

GLOW VCONT ≥ 2.5 V

PO = 16 dBm 24.5 29.0

Gain conditions Digital Mode

GHIGH VCONT ≤ 0.5 V

PO = 29 dBm 28.0 34.0

ACP1LOW VCONT ≥ 2.5 V

PO ≤ 16 dBm — –44.0

885 kHz offset

ACP1HIGH VCONT ≤ 0.5 V

PO ≤ 28.5 dBm — –44.0

ACP2LOW VCONT ≥ 2.5 V

PO ≤ 16 dBm — –58.0

Adjacent Channel Power 23

1.98 MHz offset

ACP2HIGH VCONT ≤ 0.5 V

PO ≤ 28.5 dBm — –56.0

dBc

Second FO2 PO ≤ 29 dBm — –35.0

Harmonic Suppression

Third FO3 PO ≤ 29 dBm — –40.0

dBc

Noise Power in RX Band 460-470 MHz RxBN PO ≤ 29 dBm — –126.5 dBm/Hz

Noise Figure NF — 6.5 dB

Input Voltage Standing Wave Ratio VSWR — 2.0:1 —

Stability (Spurious output) S 5:1 VSWR all phases –60.0 dBc

Ruggedness—No damage 4 Ru PO ≤ 29 dBm 10:1 VSWR

1 Per Table 2.

2 ACP is specified per CDMA2000 as the ratio of the total in-band power (1.23 MHz BW) to adjacent power in a 30 kHz BW.

3 CDMA2000 is configured as DCCH = 9600, SCHO = 9600, PCH (Walsh 0) = –3.75 dB, and Peak-to-Average Ratio (CCDF = 1%) = 4.5 dB.

4 All phases, time = 10 seconds.

PA MODULE FOR CDMA2000 (450–460 MHZ) DATA SHEET • SKY77148

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103018B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 12, 2006 5

Characterization Data

The graphs from Figure 2 through Figure 8 illustrate the

characteristics of a typical SKY77148 power amplifier designed

for operation in the PCS frequency band (450–460 MHz). This

amplifier was selected by characterizing a group of devices and

choosing a part with average electrical performance for both

nominal and the full range of recommended operating conditions,

including worst case limits.

The graphs illustrate the digital signal characteristics of the

SKY77148. Shown are power sweep characteristics for key

performance parameters over temperature and frequency, up to

29.5 dBm output power. The data was taken up to and including

16 dBm output power with the bias mode control pin setting of

VCONT = 2.5 volts. Beyond 16 dBm output power, the VCONT was set

to zero volts.

0 2 4 6 8 1012141618202224262830

Output Power (dBm)

Gain (dB)

VREF = 3.0 V VCC = 3.4 V

29.5 dBm

VCONT > 2.5 V VCONT < 0.5 V

103018_002

Figure 2. SKY77148 Gain vs. Output Power

455 @ +25 ˚C

450 @ –30 ˚C 450 @ +25 ˚C 450 @ +85 ˚C

455 @ –30 ˚C 455 @ +85 ˚C

460 @ –30 ˚C 460 @ +25 ˚C 460 @ +85 ˚C

Legend

DATA SHEET • SKY77148 PA MODULE FOR CDMA2000 (450–460 MHZ)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

6 May 12, 2006 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 103018B

100

200

300

400

500

600

700

800

0 2 4 6 8 1012141618202224262830

Output Power (dBm)

ICC (mA)

VREF = 3.0 V VCC = 3.4 V

VCONT > 2.5 V VCONT < 0.5 V

29.5 dBm

10318_003

Figure 3. SKY77148 Primary Bias current vs. Output Power

VCONT > 2.5 V VCONT < 0.5 V 29.5 dBm

103018_004

0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30

Output Power (dBm)

Power Added Efficiency (%)

VREF = 3.0 V VCC = 3.4 V

Figure 4. SKY77148 Power Added Efficiency vs. Output Power

455 @ +25 ˚C

450 @ –30 ˚C 450 @ +25 ˚C 450 @ +85 ˚C

455 @ –30 ˚C 455 @ +85 ˚C

460 @ –30 ˚C 460 @ +25 ˚C 460 @ +85 ˚C

Legend

PA MODULE FOR CDMA2000 (450–460 MHZ) DATA SHEET • SKY77148

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103018B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 12, 2006 7

0 2 4 6 8 1012141618202224262830

Output Power (dBm)

Adjacent Channel Power Ratio (–dBc)

VREF = 3.0 V VCC = 3.4 V

29.5 dBm

VCONT > 2.5 V VCONT < 0.5 V

103018_005

Figure 5. SKY77148 Adjacent Channel Power (885 kHz) vs. Output Power

0 2 4 6 8 1012141618202224262830

Output Power (dBm)

Adjacent Channel Power Ratio (–dBc)

VREF = 3.0 V VCC = 3.4 V

29.5 dBm

VCONT > 2.5 V VCONT < 0.5 V

103018_006

Figure 6. SKY77149 Adjacent Channel Power (1.98 MHz) vs. Output Power

455 @ +25 ˚C

450 @ –30 ˚C 450 @ +25 ˚C 450 @ +85 ˚C

455 @ –30 ˚C 455 @ +85 ˚C

460 @ –30 ˚C 460 @ +25 ˚C 460 @ +85 ˚C

Legend

DATA SHEET • SKY77148 PA MODULE FOR CDMA2000 (450–460 MHZ)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

8 May 12, 2006 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 103018B

024681012141618202224262830

Output Power (dBm)

2nd Harmonic Rejection (-dBc)

REF

= 3.0 V V

= 3.4 V

29.5 dBm

CONT

> 2.5 V V

CONT

< 0.5 V

103018_006

Figure 7. SKY77149 Second Harmonic Rejection vs. Output Power

103018_007

0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30

Output Power (dBm)

3rd Harmonic Rejection (–dBc)

REF

= 3.0 V V

= 3.4 V

29.5 dBm

CONT

> 2.5 V V

CONT

< 0.5 V

Figure 8. SKY77148 Third Harmonic Rejection vs. Output Power

455 @ +25 ˚C

450 @ –30 ˚C 450 @ +25 ˚C 450 @ +85 ˚C

455 @ –30 ˚C 455 @ +85 ˚C

460 @ –30 ˚C 460 @ +25 ˚C 460 @ +85 ˚C

Legend

PA MODULE FOR CDMA2000 (450–460 MHZ) DATA SHEET • SKY77148

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103018B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 12, 2006 9

Evaluation Board Description

The evaluation board is a platform for testing and interfacing

design circuitry. To accommodate the interface testing of the

SKY77148, the evaluation board schematic and assembly

diagrams are included for preliminary analysis and design. In

Figure 9, the basic schematic of the evaluation board for the 450

MHz to 460 MHz range is shown.

103018_009

RF IN

VREF

RF OUT

VCC

10000 pF

330 pF

220 pF

20 µF

3300 pF

VCC1

RF IN

VREF

GND

RF OUT

VCC2

1 µF

VCONT

Place caps at closest proximity to PA module with the capacitor grounds directly connected to the PAM grounds.

(decoupling capacitor) is not required when a voltage regulator is present.

Figure 9. Evaluation Board Schematic

C1 C4

SKYWORKS

RF IN RF OUT

VCC

VREF

GND

VCONT

GND

103018_010

(see note)

Prototype Test-Board

Component Description

Location

C2 (see note)

Value

3300 pF

1 µF

20 µF

10,000 pF

330 pF

220 pF

NOTE:

C2 (decoupling capacitor) is not required

when a voltage regulator is present.

6x6_7_PIN

03-01-01

Figure 10. Evaluation Board Assembly Diagram

DATA SHEET • SKY77148 PA MODULE FOR CDMA2000 (450–460 MHZ)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

10 May 12, 2006 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 103018B

Package Dimensions and Pin Descriptions

The SKY77148 is a multi-layer laminate base, overmold

encapsulated modular package designed for surface-mounted

solder attachment to a printed circuit board. Figure 11 is a

mechanical drawing of the pad layout for this package. Figure 12

provides a recommended phone board layout footprint for the PAM

to help the designer attain optimum thermal conductivity, good

grounding, and minimum RF discontinuity for the 50-ohm

terminals. Figure 13 shows each pin name and the pin numbering

convention, which starts with pin 1 in the upper left, as indicated,

and increments counter-clockwise around the package. Figure 14

illustrates typical case markings.

SOLDER MASK EDGES

0.8 ±0.05

7X SMT PAD

0.15 A B C

0.2 A B C

SOLDER MASK OPENING

1.5

2.825 4X 2.5

METAL PAD

PAD 1 INDICATOR

1.5 ±0.1

0.1

PAD 1 INDICATOR

6.04

0.15 A B C

(0.12)

METAL PAD EDGES

0.8 ±0.05

0.015 MIN. TYP

DETAIL B

PAD

SCALE: 2X

1X THIS ROTATION

1X ROTATED 90˚ CW

1X ROTATED 90˚ CCW

1X ROTATED 180˚

DETAIL A

PAD

SCALE: 2X

1X THIS ROTATION

1X ROTATED 90˚ CW

1X ROTATED 90˚ CCW

METAL PAD EDGES

(0.12)

SOLDER MASK EDGES

0.015MIN. TYP

TOP VIEW

BOTTOM VIEW

SIDE VIEW

ALL DIMENSIONS IN MILLIMETERS 103018_011

Figure 11. SKY77148 Package Dimensions

PA MODULE FOR CDMA2000 (450–460 MHZ) DATA SHEET • SKY77148

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103018B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 12, 2006 11

103018_012

STENCIL APERTURE

TOP VIEW

STENCIL APERTURE SIZE FOR THE CENTER GROUND

PAD SHOULD BE 80% TO 100% (BY AREA)

OF THE SOLDER MASK OPENING.

6.34

2X 1.5

7X 1.07

PAD 1 PAD 7

7X 0.8

2.83

1.5

4X 2.5

Package Outline

Exposed Center Pad

3.17

6.44

2X 1.5

7X 1.17

PAD 1

7X 0.9

4X 2.5

3.22

Exposed Center Pad

Package Outline

1.5

2.83

SOLDER MASK OPENING

TOP VIEW

METALLIZATION

TOP VIEW

THE SHADED AREA REPRESENTS THE MERGER OF THE CENTER GROUND PAD

AND 1 INDIVIDUAL I/O GROUND PAD. THEREFORE, THE NUMBER

OF PLACES DIMENSIONED WILL BE REDUCED.

Thermal Via Array under PA areas.

Ø0.3 mm on 0.6 pitch. Additional

vias will improve thermal performance.

NOTE: Thermal vias should be tented

and filled with solder mask, 30–35 µm

Cu plating is recommended.

Package Outline

6.34

0.6

3.17

0.6

6X 0.8

PAD 1

6X 1.07 0.25

Common Ground Pad

3X 2.5

Figure 12. Phone PCB Layout Footprint for 6 x 6, 7-Pad Package – SKY77148

DATA SHEET • SKY77148 PA MODULE FOR CDMA2000 (450–460 MHZ)

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

12 May 12, 2006 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • 103018B

103018_013

345

VCC1

RF IN

VREF

VCONT

VCC2

RF OUT

GND

GROUND PAD

Pad layout as seen from top view looking through the package.

GROUND PAD is package underside.

Figure 13. Pin Names and Configuration

103018_014

Revision

Number

Pin 1

Identifier

Lot Number

Country Code

Manufacturing

Part Number

Year

Manufactured

Week Package

Sealed

SKY77148-NN

EXXXXX.XX

YYWW MEX

Figure 14. Typical Case Markings

Package and Handling Information

Because of its sensitivity to moisture absorption, this device

package is baked and vacuum packed prior to shipment.

Instructions on the shipping container label must be followed

regarding exposure to moisture after the container seal is broken,

otherwise, problems related to moisture absorption may occur

when the part is subjected to high temperature during solder

assembly.

The SKY77148 is capable of withstanding an MSL 3/235 °C solder

reflow. Care must be taken when attaching this product, whether

it is done manually or in a production solder reflow environment. If

the part is attached in a reflow oven, the temperature ramp rate

should not exceed 3 °C per second; maximum temperature should

not exceed 235 °C. If the part is manually attached, precaution

should be taken to insure that the part is not subjected to

temperatures exceeding 235 °C for more than 10 seconds. For

details on attachment techniques, precautions, and handling

procedures recommended by Skyworks, please refer to Skyworks

Application Note: PCB Design and SMT Assembly/Rework,

Document Number 101752. Additional information on standard

SMT reflow profiles can also be found in the JEDEC Standard

J-STD–020.

Production quantities of this product are shipped in the standard

tape-and-reel format. For packaging details, refer to Skyworks

Application Note: Tape and Reel, Document Number 101568.

Electrostatic Discharge Sensitivity

The SKY77148 is a Class 1 device. Figure 15 lists the Electrostatic

Discharge (ESD) immunity level for each pin of the SKY77148

product. The numbers in Figure 15 specify the ESD threshold level

for each pin where the I-V curve between the pin and ground

starts to show degradation. The ESD testing was performed in

compliance with MIL-STD-883E Method 3015.7 using the Human

Body Model. If ESD damage threshold magnitude is found to

consistently exceed 2000 volts on a given pin, this so is indicated.

If ESD damage threshold below 2000 volts is measured for either

polarity, numbers are indicated that represent worst case values

observed in product characterization.

345

VCC1

> +2 kV

< –2 kV

RF IN

> +2 kV

< –2 kV

VREF

> +2 kV

< –2 kV

VCONT

> +2 kV

< –2 kV

VCC2

> +1.6 kV

< –2.0 kV

RF OUT

> +2 kV

< –2 kV

GND

GROUND PAD

103018_015

Pad layout as seen from top view looking through the package.

Figure 15. ESD Sensitivity Areas (Top View)

Various failure criteria can be utilized when performing ESD

testing. Many vendors employ relaxed ESD failure standards,

which fail devices only after “the pin fails the electrical

specification limits” or “the pin becomes completely non-

functional”. Skyworks employs most stringent criteria to fail

devices as soon as the pin begins to show any degradation on a

curve tracer. To avoid ESD damage, either latent or visible, it is

very important that the product assembly and test areas follow the

Class 1 ESD handling precautions listed in Table 6.

PA MODULE FOR CDMA2000 (450–460 MHZ) DATA SHEET • SKY77148

Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com

103018B • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice. • May 12, 2006 13

Table 6. Precautions for Handling GaAs IC-based Products to Avoid Induced Damage

Wrist Straps

Conductive Smocks, Gloves and Finger Cots

Personnel Grounding

Antistatic ID Badges

Relative Humidity Control and Air Ionizers

Facility Dissipative Floors (less than 109 Ω to GND)

Dissipative Table Tops

Protective Test Equipment (Properly Grounded)

Grounded Tip Soldering Irons

Conductive Solder Suckers

Protective Workstation

Static Sen sors

Bags and Pouches (Faraday Shield)

Protective Tote Boxes (Conductive Static Shielding)

Protective Trays

Grounded Carts

Protective Packaging and Transportation

Protective Work Order Holders

Ordering Information

Model Number Manufacturing

Part Number Product Revision Package Operating Temperature

SKY77148 SKY77148 –15 7-pin MCM L4

6 x 6 x 1.5 mm –30 °C to +85 °C

Revision History

Revision Level Date Description

A October 19, 2005 Initial Release

B May 12, 2006 Revise: Tables 2, 4

References

Application Note: PCB Design and SMT Assembly/Rework, Document Number 101752

Application Note: Tape and Reel Information – RF Modules, Document Number 101568

JEDEC Standard J–STD015–020

Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products. These materials are provided by Skyworks as a service to its customers and may be

used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials. Skyworks may make changes to its documentation, products,

specifications and product descriptions at any time, without notice. Skyworks makes no commitment to update the information and shall have no responsibility whatsoever for conflicts,

incompatibilities, or other difficulties arising from future changes to its documentation, products, specifications and product descriptions.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by or under this document. Except as may be provided in Skyworks Terms and Conditions of

Sale for such products, Skyworks assumes no liability whatsoever in association with its documentation, products, specifications and product descriptions.

THESE MATERIALS ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED OR OTHERWISE, RELATING TO SALE AND/OR USE OF SKYWORKS PRODUCTS

INCLUDING WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER

INTELLECTUAL PROPERTY RIGHT. SKYWORKS FURTHER DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN

THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST

REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THESE MATERIALS WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGE.

Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications. Skyworks customers using or selling Skyworks products for use in such applications do so at their

own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale.

The following are trademarks of Skyworks Solutions, Inc.: Skyworks®, the Skyworks logo, and Breakthrough Simplicity®. Product names or services listed in this publication are for identification

purposes only, and may be trademarks of Skyworks or other third parties. Third-party brands and names are the property of their respective owners. Additional information, posted at