ISL9011AIRKCZ - Intersil Corporation

FN6437.1

ISL9011A

Dual LDO with Low Noise, Low IQ and

High PSRR

ISL9011A is a high performance dual LDO capable of

sourcing 150mA current from Channel 1 and 300mA from

Channel 2. The device has a low standby current and

high-PSRR and is stable with output capacitance of 1µF to

10µF with ESR of up to 200mΩ.

A reference bypass pin allows an external capacitor for

adjusting a noise filter for low noise and high PSRR

applications.

The quiescent current is typicall y only 45µA with both LDOs

enabled and active. Separate enable pins control each

individual LDO output. When both enable pins are low, the

device is in shutdown, typically drawing less than 0.1µA.

Several combinations of voltage outputs are standard.

Output voltage options for each LDO range from 1.5V to

3.3V. Other output voltage options may be available upon

request.

Pinout ISL9011A

(10 LD 3x3 DFN)

TOP VIEW

Features

• Integrates two high performance LDOs

- VO1 - 150mA output

- VO2 - 300mA output

• Excellent transient response to large current steps

• Excellent load regulation: <1% voltage change across full

range of load current

• High PSRR: 70dB @ 1kHz

• Wide input voltage capability: 2.3V to 6.5V

• Extremely low quiescent current: 45µA (both LDOs active)

• Low dropout voltage: typically 120mV @ 150mA

• Low output noise: typically 30µVRMS @ 100µA (1.5V)

• Stable with 1µF to 10µF ceramic capacitors

• Separate enable pins for each LDO

• Soft-start to limit input current surge during enable

• Current limit and overheat protection

• ±1.8% accuracy over all operating conditions

• Tiny 10 Ld 3mmx3mm DFN package

• -40°C to +85°C operating temperature range

• Pin compatible with Micrel MIC2211

• Pb-free (RoHS compliant)

Applications

• PDAs, Cell Phones and Smart Phones

• Portable Instruments, MP3 Players

• Handheld Devices including Medical Handhelds

VIN

EN1

EN2

CBYP

VO1

VO2

GND

Data Sheet March 7, 2008

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

1-888-INTERSIL or 1-888-468-3774 |Intersil (and design) is a registered trademark of Intersil Americas Inc.

All other trademarks mentioned are the property of their respective owners.

2FN6437.1

March 7, 2008

Ordering Information

PART NUMBER

(Notes 1, 2, 3) PART MARKING VO1 VOLTAGE

(V) VO2 VOLTAGE

(V) TEMP RANGE (°C) PACKAGE

(Pb-free) PKG. DWG. #

ISL9011AIRNNZ DGPA 3.3 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRNJZ DGNA 3.3 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRNFZ DGMA 3.3 2.5 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRNCZ DGLA 3.3 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRMNZ DGKA 3.0 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRMMZ DGJA 3.0 3.0 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRMGZ DGHA 3.0 2.7 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRLLZ DGGA 2.9 2.9 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRKNZ DGEA 2.85 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRKKZ DGDA 2.85 2.85 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRKJZ DGCA 2.85 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRKFZ DGBA 2.85 2.5 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRKPZ DGFA 2.85 1.85 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRKCZ DFYA 2.85 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRJNZ DFVA 2.8 3.3 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRJMZ DFTA 2.8 3.0 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRJRZ DWFA 2.8 2.6 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRJCZ DFSA 2.8 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRJBZ DFRA 2.8 1.5 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRGPZ DFPA 2.7 1.85 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRGCZ DFNA 2.7 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRFJZ DFMA 2.5 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRFDZ DFLA 2.5 2.0 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRFCZ DFKA 2.5 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRPLZ DGRA 1.85 2.9 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRPPZ DGSA 1.85 1.85 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRCJZ DFJA 1.8 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRCCZ DFHA 1.8 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRBLZ DFGA 1.5 2.9 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRBJZ DFFA 1.5 2.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRBCZ DFEA 1.5 1.8 -40 to +85 10 Ld 3x3 DFN L10.3x3C

ISL9011AIRBBZ DFDA 1.5 1.5 -40 to +85 10 Ld 3x3 DFN L10.3x3C

NOTES:

1. Add “-T” suffix for tape and reel. Please refer to TB347 for details on reel specifications.

2. For availability and lead time of devices with voltage combinations not listed in the table , contact In tersil Marketing.

3. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte

tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations.

Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC

J STD-020.

ISL9011A

3FN6437.1

March 7, 2008

Absolute Maximum Ratings Thermal Information

Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +7.1V

VO1, VO2 Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.6V

All Other Pins . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to (VIN + 0.3)V

Recommended Operating Conditions

Ambient Temperature Range (TA) . . . . . . . . . . . . . . .-40°C to +85°C

Supply Voltage (VIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3V to 6.5V

Thermal Resistance (Notes 4, 5) θJA (°C/W) θJC (°C/W)

10 Ld 3x3 DFN Package . . . . . . . . . . . 50 10

Junction Temperature Range . . . . . . . . . . . . . . . . .-40°C to +125°C

Operating Temperature Range . . . . . . . . . . . . . . . . .-40°C to +85°C

Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C

Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below

http://www.intersil.com/pbfree/Pb-FreeReflow.asp

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and

result in failures not covered by warranty.

NOTES:

4. θJA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See

Tech Brief TB379.

5. For θJC, the “case temp” location is the center of the exposed metal pad on the package underside.

Electrical Specifications Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and temperature

range of the device as follows: TA = -40°C to +85°C; VIN = (VO + 1.0V) to 6.5V with a minimum VIN of 2.3V;

CIN = 1µF; CO = 1µF; CBYP = 0.01µF

PARAMETER SYMBOL TEST CONDITIONS MIN

(Note 7) TYP MAX

(Note 7) UNITS

DC CHARACTERISTICS

Supply Voltage VIN 2.3 6.5 V

Ground Current Quiescent condition: IO1 = 0µA; IO2 = 0µA

IDD1 One LDO active 25 40 µA

IDD2 Both LDO active 45 60 µA

Shutdown Current IDDS @ +25°C 0.1 1.0 µA

UVLO Threshold VUV+ 1.9 2.1 2.3 V

VUV- 1.6 1.8 2.0 V

Regulation V oltage Accuracy V ariation from nominal volt age output, VIN = VO+ 0.5 to 5.5V,

TJ= -40°C to +125°C -1.8 +1.8 %

Line Regulation VIN = (VOUT + 1.0V relative to highest output voltage) to 5.5V -0.2 0 0.2 %/V

Load Regulation IOUT = 100µA to 150mA (VO1 and VO2) 0.1 0.7 %

IOUT = 100µA to 300mA (VO2) 1.0 %

Maximum Output Current IMAX VO1: Continuous 150 mA

VO2: Continuous 300 mA

Internal Current Limit ILIM 350 475 600 mA

Dropout Voltage (Note 6) VDO1 IO = 150mA; VO > 2.1V (VO1) 125 200 mV

VDO2 IO = 300mA; VO < 2.5V (VO2) 300 500 mV

VDO3 IO = 300mA; 2.5V ≤ VO ≤ 2.8V (VO2) 250 400 mV

VDO4 IO = 300mA; VO > 2.8V (VO2) 200 325 mV

Thermal Shutdown Temperature TSD+ 145 °C

TSD- 110 °C

AC CHARACTERISTICS

Ripple Rejection IO = 10mA, VIN = 2.8V(min), VO = 1.8V, CBYP = 0.1µF

@ 1kHz 70 dB

@ 10kHz 55 dB

@ 100kHz 40 dB

Output Noise Voltage IO = 100μA, VO = 1.5V, TA = +25°C, CBYP = 0.1µF

BW = 10Hz to 100kHz 30 µVRMS

ISL9011A

4FN6437.1

March 7, 2008

DEVICE START-UP CHARACTERISTICS

Device Enable Time tEN T ime from assertion of the ENx pin to when the output voltage

reaches 95% of the VO(nom) 250 500 µs

LDO Soft-Start Ramp Rate tSSR Slope of linear portion of LDO output voltage ramp during

start-up 30 60 µs/V

EN1, EN2 PIN CHARACTERISTICS

Input Low Voltage VIL -0.3 0.5 V

Input High Voltage VIH 1.4 VIN +

0.3 V

Input Leakage Current IIL, IIH 0.1 µA

Pin Capacitance CPIN Informative 5 pF

NOTE:

6. VOx = 0.98*VOx(NOM); Valid for VOx greater than 1.85V.

7. Parts are 100% tested at +25°C. Temperature limits established by characterization and are not production tested.

Electrical Specifications Unless otherwise noted, all parameters are guaranteed over the operational supply voltage and temperature

range of the device as follows: TA = -40°C to +85°C; VIN = (VO + 1.0V) to 6.5V with a minimum VIN of 2.3V;

CIN = 1µF; CO = 1µF; CBYP = 0.01µF (Continued)

PARAMETER SYMBOL TEST CONDITIONS MIN

(Note 7) TYP MAX

(Note 7) UNITS

ISL9011A

5FN6437.1

March 7, 2008

Typical Performance Curves

FIGURE 1. OUTPUT VOLTAGE vs INPUT VOLTAGE

(3.3V OUTPUT) FIGURE 2. OUTPUT VOLTAGE CHANGE vs LOAD CURRENT

FIGURE 3. OUTPUT VOLTAGE CHANGE vs TEMPERATURE FIGURE 4. OUTPUT VOLTAGE vs INPUT VOLT AGE

(VO1=3.3V)

FIGURE 5. OUTPUT VOL TAGE vs INPUT VOL TAGE

(VO2=2.8V) FIGURE 6. DROPOUT VOLTAGE vs LOAD CURRENT

OUTPUT VOLTAGE, VO (%)

INPUT VOLTAGE (V)

-0.6

-0.2

0.2

0.6

-0.8 3.8 4.2 6.25.8 6.63.4 4.6 5.0 5.4

-0.4

0.0

0.4

0.8 VO = 3.3V

+85°C

-40°C

+25°C

ILOAD = 0mA

0.04

0.06

-0.06

-0.10 100 200 300 4000LOAD CURRENT - IO (mA)

OUTPUT VOLTAGE CHANGE (%)

-0.02

0.00

0.02

0.08

0.10

-0.04

-0.08

50 150 250 350

VIN = 3.8V

VO = 3.3V

+85°C

-40°C

+25°C

0.04

0.06

-0.06

-0.10 -10 20 50 110-40 TEMPERATURE (°C)

OUTPUT VOLTAGE CHANGE (%)

-0.02

0.00

0.02

0.08

0.10

-0.04

-0.08

-25 5 35 8065 95 125

VIN = 3.8V

VO = 3.3V

ILOAD = 0mA

OUTPUT VOLTAGE, VO (V)

INPUT VOLTAGE (V)

3.0

3.1

3.2

3.3

3.4

2.9

2.8 3.1 3.6 4.1 4.6 5.1 6.15.6

IO = 150mA

IO = 0mA VO1 = 3.3V

6.5

2.5

2.6

2.7

2.8

2.9

2.4

2.3 2.63.13.64.14.65.1 6.1

INPUT VOLTAGE (V)

OUTPUT VOLTAGE, VO (V)

5.6

IO = 0mA

IO = 300mA

VO2 = 2.8V

IO = 150mA

6.5

200

250

300

350

150

100

050 100 150 200 250 300 350 4000OUTPUT LOAD (mA)

DROPOUT VOLTAGE, VDO (mV)

VO2 = 2.8V

VO1 = 3.3V

ISL9011A

6FN6437.1

March 7, 2008

FIGURE 7. VO1 DROPOUT VOLTAGE vs LOAD CURRENT FIGURE 8. GROUND CURRENT vs INPUT VOLTAGE

FIGURE 9. GROUND CURRENT vs LOAD FIGURE 10. GROUND CURRENT vs TEMPERATURE

FIGURE 11. POWER-UP/POWER-DOWN FIGURE 12. TURN-ON/TURN-OFF RESPONSE

Typical Performance Curves (Continued)

100

125

150

175

025 50 75 100 125 150 175 2000OUTPUT LOAD (mA)

DROPOUT VOLTAGE, VDO (mV)

VO1 = 3.3V

+85°C +25°C -40°C

25 4.0 5.0 6.5

INPUT VOLTAGE (V)

GROUND CURRENT (µA)

3.0 3.5 4.58 5.5 6.0

IO(BOTH CHANNELS) = 0µA

VO1 = 3.3V

VO2 = 2.8V

-40°C

+25°C

+125°C

200

160

100

050 100 150 200 250 4000

LOAD CURRENT (mA)

GROUND CURRENT (µA)

350300

VO1 = 3.3V

VIN = 3.8V

VO2 = 2.8V

120

140

180

+85°C

-40°C

+25°C

25 -10 20 50 110-40 TEMPERATURE (°C)

GROUND CURRENT (µA)

-25 5 35 8065 95 125

VIN = 3.8V

VO = 3.3V

ILOAD = 0µA

BOTH OUTPUTS ON

1234567 10

TIME (s)

VOLTAGE (V)

VO2

VO1

VIN

VO1 = 3.3V

VO2 = 2.8V

IL1 = 150mA

IL2 = 300mA

1234567 10

TIME (s)

VOLTAGE (V)

VO2

VO1

VIN

100 200 300 400 500 600 700 8000

TIME (µs)

VO1 (V)VEN (V)

VO1 = 3.3V

VIN = 5.0V

IL1 = 150mA

CL-1, CL-2 = 1µF

CBYP = 0.01µF

900 1000

VO2 (10mV/DIV)

IL2 = 300mA

VO2 = 2.8V

ISL9011A

7FN6437.1

March 7, 2008

FIGURE 13. LINE TRANSIENT RESPONSE, 3.3V OUTPUT FIGURE 14. LINE TRANSIENT RESPONSE, 2.8V OUTPUT

FIGURE 15. LOAD TRANSIENT RESPONSE FIGURE 16. PSRR vs FREQUENCY

FIGURE 17. SPECTRAL NOISE DENSITY vs FREQUENCY

Typical Performance Curves (Continued)

400µs/DIV

VO1 = 3.3V

ILOAD = 150mA

3.6V

4.3V

10mV/DIV

CLOAD = 1μF

CBYP = 0.01μF

VO1 = 3.3V

ILOAD = 150mA

3.6V

4.3V

10mV/DIV

CLOAD = 1µF

CBYP = 0.01µF

400µs/DIV

VO2 = 2.8V

ILOAD = 300mA

3.5V

4.2V

10mV/DIV

CLOAD = 1µF

CBYP = 0.01µF

400µs/DIV

VO2 = 2.8V

ILOAD = 300mA

3.5V

4.2V

10mV/DIV

CLOAD = 1µF

CBYP = 0.01µF

100µs/DIV

VO (25mV/DIV)

ILOAD

300mA

100µA

VIN = 2.8V

VO = 1.8V

0.1 1k 10k 100k 1M

FREQUENCY (Hz)

100

PSRR (dB)

VIN = 3.6V

VO = 1.8V

IO = 10mA

CBYP = 0.1µF

CLOAD = 1µF

SPECTRAL NOISE DENSITY (nV/√Hz)

1000

100

0.1

10 100 1k 10k 100k 1M

FREQUENCY (Hz)

VIN = 3.6V

VO = 1.8V

ILOAD = 10mA

CBYP = 0.1µF

CIN = 1µF

CLOAD = 1µF

ISL9011A

8FN6437.1

March 7, 2008

Typical Application

Pin Descriptions

NUMBER PIN

NAME TYPE DESCRIPTION

1 VIN Analog I/O Supply Voltage/LDO Input:

Connect a 1µF capacitor to GND.

2 EN1 Low Voltage Compatible

CMOS Input LDO-1 Enable.

3 EN2 Low Voltage Compatible

CMOS Input LDO-2 Enable.

4 CBYP Analog I/O Reference Bypass Capacitor Pin: Optionally connect capacitor of value 0.01µF to 1µF

between this pin and GND to tune in the desired noise and PSRR performance.

5, 7, 8 NC NC No Connection

6 GND Ground GND is the connection to system ground. Connect to PCB Ground plane.

9VO2

Analog I/O LDO-2 Output: Connect capacitor of value 1µF to 10µF to GND (1µF recommended).

10 VO1 Analog I/O LDO-1 Output: Connect capacitor of value 1µF to 10µF to GND (1µF recommended).

C1, C3, C4: 1µF X5R CERAMIC CAPACITOR

C2: 0.1µF X5R CERAMIC CAPACITOR

ISL9011A

VIN

EN1

EN2

CBYP

VO1

VO2

GND

VIN (2.3V TO 6.5V)

ENABLE 1

ENABLE 2

VOUT 1

VOUT 2

C1 C2 C3 C4

OFF

ISL9011A

9FN6437.1

March 7, 2008

Block Diagram

Functional Description

The ISL9011A contains all circuitry required to implement

two high performance LDOs. High performance is achieved

through a circuit that delivers fast transient response to

varying load conditions. In a quiescent condition, the

ISL9011A adjusts its biasing to achieve the lowest standby

current consumption.

The device also integrates current limit protection, smart

thermal shutdown protection, staged turn-on and soft-start.

Smart Thermal shutdown protects the device against

overheating. Staged turn-on and soft-start minimize start-up

input current surg es w itho u t causing ex ces sive device

turn-on time.

Power Control

The ISL9011A has two separate enable pins (EN1 and EN2)

to individually control power to each of the LDO outputs.

When both EN1 and EN2 are low, the device is in shutdown

mode. During this condition, all on-chip circuits are off, and

the device draws minimum current, typically less than 0.1µA.

When one or both of the enable pi ns ar e asserted, the

device first polls the outpu t of th e UV LO detector to ensure

that VIN voltage is at least about 2.1V. On ce verified, the

device initiates a start-up sequence. During the start-up

sequence, trim settings are first read and latched. Then,

sequentially, the bandgap, reference voltage and current

generation circuitry power-up. Once the references are

stable, a fast-start circuit quickly charges the external

reference bypass capacitor (connected to the CBYP pin) to

the proper operating voltage. After the bypass capacitor has

been charged, the LDO’s power-up.

If EN1 is brought high, and EN2 goes high before the VO1

output stabilizes, the ISL9011A delays the VO2 turn-on until

the VO1 output reaches its target level.

If EN2 is brought high, and EN1 goes high before VO2 starts

its output ramp, then VO1 turns on first and the ISL9011A

LDO

ERROR

AMPLIFIER

IS1

QEN1

LDO-1

LDO-2

VREF

TRIM

VIN

VO1

VO2

CBYPGND

EN2

EN1 CONTROL

LOGIC

VOLTAGE

REFERENCE

GENERATOR

BANDGAP AND

TEMPERATURE

SENSOR

UVLO 1.00V

IS1

IS2

QEN1

QEN2

VO1

~1.0V

ISL9011A

10 FN6437.1

March 7, 2008

delays the VO2 turn-on until the VO1 output reaches its

target level.

If EN2 is brought high, and EN1 goes high after VO2 starts

its output ramp, then the ISL9011A immediately starts to

ramp up the VO1 output.

If both EN1 and EN2 are brought high at the same time, the

VO1 output has priority, and is always powered up first.

During operation, whenever the VIN voltage drops below

about 1.8V, the ISL9011A immediately disables both LDO

outputs. When VIN rises back above 2.1V, the device

re-initiates its start-up sequence and LDO operation will

resume automatically.

Reference Generation

The reference generation circuitry includes a trimmed

bandgap, a trimmed voltage reference divide r, a trimmed

current reference generator , and an RC noise filter . The filter

includes the external capacitor connected to the CBYP pin.

A 0.01µF capacitor connected CBYP implements a 100Hz

lowpass filter, and is recommended for most high

performance applications. For the lowest noise application, a

0.1µF or greater CBYP capacitor should be used. This filters

the reference noise to below the 10Hz to 1kHz frequen cy

band, which is crucial in many noise-sensitive applications.

The bandgap generates a zero temperature coefficient (TC)

voltage for the reference divider. The reference divider

provides the regulation reference and other voltage

references required for current generation and

over-temperature detection.

The current generator outputs references required for

adaptive biasing as well as references for LDO output

current limit and thermal shutdown determination.

LDO Regulation and Progra mmable Output Divider

The LDO Regulator is implemented with a high-gain

operational amplifier driving a PMOS pass transistor. The

design of the ISL9011A provides a regulator that has low

quiescent current, fast transient response, and overall

stability across all operating and load current conditions.

LDO stability is guaranteed for a 1µF to 10µF output

capacit or that has a t olerance bett er than 20% an d ESR less

than 200mΩ. The design is performance-optimized for a 1µF

capacitor. Unless limited by the application, use of an output

capacitor value above 4.7µF is not recommended as LDO

performance improvement is minimal.

Soft-start circuitry integrated into each LDO limits the initial

ramp-up rate to about 30µs/V to minimize current surge. The

ISL9011A provides short-circuit protection by limiting the

output current to about 475mA.

Each LDO uses an independently trimmed 1V reference. An

internal resistor divider drops the LDO output voltage down

to 1V. This is compared to the 1V reference for regulation.

The resistor division ratio is programmed in the factory.

Overheat Detection

The bandgap outputs a proportional-to-temperature current

that is indicative of the temperature of the silicon. This

current is compared with references to determine if the

device is in danger of damage due to overheating. When the

die temperature reaches about +14 5°C, one or both of the

LDO’s momentarily shut down until the die cools sufficiently.

In the overheat condition, only the LDO sourcing more than

50mA will be shut off. This does not affect the operation of

the other LDO. If both LDOs source more than 50mA and an

overheat condition occurs, both LDO outputs are disabled.

Once the die temperature falls back below about +110°C,

the disabled LDO(s) are re-enabled and soft-start

automatically takes place.

ISL9011A

All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.

Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality

Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without

notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and

reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result

from its use. No lice nse is gran t ed by i mpli catio n or other wise u nder an y p a tent or patent rights of Intersi l or it s sub sidi ari es.

For information regarding Intersil Corporation and its products, see www.intersil.com

FN6437.1

March 7, 2008

ISL9011A

Dual Flat No-Lead Plastic Package (DFN)

NX (b)

SECTION "C-C"

FOR ODD TERMINAL/SIDE

TERMINAL TIP

(A1)

BOTTOM VIEW

AREA

INDEX

0.10

0.08

SIDE VIEW

0.10

C0.10

TOP

VIEW

AREA

INDEX

NX L

E2/2

REF.

(Nd-1)Xe

(DATUM A)

(DATUM B)

0.10

BAC

N-1

PLANE

SEATING

NX b

D2/2

NX k

L10.3x3C

10 LEAD DUAL FLAT NO-LEAD PLASTIC PACKAGE

SYMBOL

MILLIMETERS

NOTESMIN NOMINAL MAX

A 0.85 0.90 0.95 -

A1 - - 0.05 -

A3 0.20 REF -

b 0.20 0.25 0.30 5, 8

D 3.00 BSC -

D2 2.33 2.38 2.43 7, 8

E 3.00 BSC -

E2 1.59 1.64 1.69 7, 8

e 0.50 BSC -

k0.20- - -

L 0.35 0.40 0.45 8

N102

Nd 5 3

Rev. 1 4/06

NOTES:

1. Dimensioning and tolerancing conform to ASME Y14.5-1994.

2. N is the number of terminals.

3. Nd refers to the number of terminals on D.

4. All dimensions are in millimeters. Angles are in degrees.

5. Dimension b applies to the metallized terminal and is measured

between 0.15mm and 0.30mm from the terminal tip.

6. The configuration of the pin #1 identifier is optional, but must be

located wi thin the zone indicated. The pin #1 identif ier may be

either a mold or mark feature.

7. Dimensions D2 and E2 are for the exposed pads which provide

improved electrical and thermal performance.

8. Nominal dimensions are provided to assist with PCB Land

Pattern Design efforts, see Intersil Technical Brief TB389.

9. COMPLIANT TO JEDEC MO-229-WEED-3 except for

dimensions E2 & D2.