POWER LPS170-M Series Medical Data Sheet 175 Watts Total Power: 100 - 175 Watts Input Voltage: 85 - 264 Vac 120 - 300 Vdc # of Outputs: Single SPECIAL FEATURES Medical safety approvals Active power factor correction IEC EN61000-3-2 compliance Wide range adjustable output; Remote sense on main output Single wire current sharing Power fail and remote inhibit Built-in EMI filter Low output ripple Overvoltage protection Overload protection Thermal overload protection DC power good 5 V standby output 12 V Aux output Optional cover (-C suffix) RoHS compliant SAFETY TUV UL CSA CB CE 60601-1 UL2601 CSA 22.2 No. 601.1 Certificate and report Mark (LVD) Electrical Specifications Input Input range 85 - 264 Vac; 120 - 300 Vdc Frequency 47 - 67 Hz Inrush current 38 A max, cold start @ 25 C Efficiency 75% typical at full load EMI filter FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted Power Factor 0.99 typical Safety ground leakage current <250 A @ 50/60 Hz, 264 Vac inputs Output Maximum power 110 W convection (75 W with cover) 175 W with 30 CFM forced air (130 W with cover) Adjustment range 2:1 wide ratio minimum Standby outputs 5 V @ 2 A regulated 5% Hold-up time 20 ms @175 W load at nominal line Overload protection Short circuit protection on all outputs. Case overload protected @ 110-145% above peak rating Overvoltage protection 10% to 40% above nominal output Aux output 12 V @ 1 A -5 %, +10% LPS170-M Series Data Sheet Logic Control Power failure TTL logic signal goes high 100 - 500 msec after V1 output; It goes low at least 4 msec before loss of regulation Remote inhibit Requires contact closure to inhibit outputs Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. DC - OK TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation Environmental Specifications Operating temperature 0 to 50 C ambient; derate each output at 2.5% per degree from 50 to 70 C Low temperature start -20 C Temperature coefficient 0.4% per C Storage temperature -40 to 85 C Electromagnetic susceptibility Designed to meet IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity Operating; non-condensing 5% to 95% Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75G peak 5Hz to 500Hz, operational MTBF demonstrated >550,000 hours at full load and 25 C ambient conditions Ordering Information Model Number Maximum Load Maximum Load with Convection with 30CFM Cooling Forced Air Output Voltage Minimum Load LPS172-M 5 V (2.5 - 6 V) 0A 22 A 35 A 38 A 2% 50 mV LPS173-M 12 V (6 - 12 V) 0A 9.1 A 15 A 16.5 A 2% 120 mV LPS174-M 15 V (12 - 24 V) 0A 7.3 A 12 A 13.2 A 2% <1% LPS175-M 24 V (24 - 54 V) 0A 4.5 A 7.5 A 8.2 A 2% <1% Peak Load1 Regulation2 Ripple P/P(PARD)3 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25 C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4. Remote inhibit resets OVP latch. 5. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. Note: -C suffix added to the model number indicates cover option. Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is 0.02". 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Mounting screw maximum insertion depth is 0.12". 5. Warranty: 2 years 6. Weight: 1.8 lb/0.85 kg LPS170-M Series Data Sheet Mechanical Drawing 7% 7% LPS170-M Series Data Sheet Pin Assignments Connector LPS17x SK1 PIN 1 +12 V PIN 2 5 V Standby PIN 3 Common PIN 4 V1 SWP PIN 5 Common PIN 6 +V1 sense PIN 7 Sense common PIN 8 Remote inhibit PIN 9 DC power good PIN 10 POK TB-1 COMMON TB-2 Main output PIN 1 GROUND PIN 3 LINE Pin 5 NEUTRAL SK3 SK4 Mating Connectors AC Input (SK4) Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) PINS: 08-58-0111 DC Outputs (SK3) Molex 19141-0058 Control Signals (SK1) Molex 90142-0010 (USA) PINS: 90119-2110 or Amp: 87977-3 PINS: 87309-8 Artesyn Embedded Technologies Connector Kit #70-841-016 WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. Specifications subject to change without notice. (c) 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit www.artesyn.com/legal. www.artesyn.com For more information: www.artesyn.com/power For support: productsupport.ep@artesyn.com LPS170-M Series-DS 10Jul2017