POWER
LPS170-M Series
Medical
175 Watts
Total Power: 100 - 175 Watts
Input Voltage: 85 - 264 Vac
120 - 300 Vdc
# of Outputs: Single
SPECIAL FEATURES
Medical safety approvals
Active power factor correction
IEC EN61000-3-2 compliance
Wide range adjustable output;
Remote sense on main output
Single wire current sharing
Power fail and remote inhibit
Built-in EMI lter
Low output ripple
Overvoltage protection
Overload protection
Thermal overload protection
DC power good
5 V standby output
12 V Aux output
Optional cover (-C sufx)
RoHS compliant
SAFETY
TUV 60601-1
UL UL2601
CSA CSA 22.2 No. 601.1
CB Certicate and report
CE Mark (LVD)
Electrical Specications
Input
Input range 85 - 264 Vac; 120 - 300 Vdc
Frequency 47 - 67 Hz
Inrush current 38 A max, cold start @ 25 °C
Efciency 75% typical at full load
EMI lter
FCC Class B conducted
CISPR 22 Class B conducted
EN55022 Class B conducted
VDE 0878 PT3 Class B conducted
Power Factor 0.99 typical
Safety ground leakage current <250 μA @ 50/60 Hz, 264 Vac inputs
Output
Maximum power 110 W convection (75 W with cover)
175 W with 30 CFM forced air (130 W with cover)
Adjustment range 2:1 wide ratio minimum
Standby outputs 5 V @ 2 A regulated ±5%
Hold-up time 20 ms @175 W load at nominal line
Overload protection Short circuit protection on all outputs.
Case overload protected @ 110-145% above peak rating
Overvoltage protection 10% to 40% above nominal output
Aux output 12 V @ 1 A -5 %, +10%
Data Sheet
LPS170-M Series Data Sheet
Logic Control
Power failure
TTL logic signal goes high 100 - 500 msec after V1 output; It goes low at least 4 msec before loss of regulation
Remote inhibit Requires contact closure to inhibit outputs
Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection
protected.
DC - OK TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation
Environmental Specications
Operating temperature 0° to 50 °C ambient; derate each output at 2.5% per degree from 50° to 70 °C
Low temperature start -20 °C
Temperature coefcient ±0.4% per °C
Storage temperature -40° to 85 °C
Electromagnetic susceptibility Designed to meet IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11 Level 3
Humidity Operating; non-condensing 5% to 95%
Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75G peak 5Hz to
500Hz, operational
MTBF demonstrated >550,000 hours at full load and 25 °C ambient conditions
Ordering Information
Model
Number
Output
Voltage
Minimum
Load
Maximum Load
with Convection
Cooling
Maximum Load
with 30CFM
Forced Air
Peak Load1Regulation2Ripple
P/P(PARD)3
LPS172-M 5 V (2.5 - 6 V) 0 A 22 A 35 A 38 A ±2% 50 mV
LPS173-M 12 V (6 - 12 V) 0 A 9.1 A 15 A 16.5 A ±2% 120 mV
LPS174-M 15 V (12 - 24 V) 0 A 7.3 A 12 A 13.2 A ±2% <1%
LPS175-M 24 V (24 - 54 V) 0 A 4.5 A 7.5 A 8.2 A ±2% <1%
1. Peak current lasting <30 seconds with a maximum 10% duty cycle.
2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings.
3. Peak-to-peak with 20 MHz bandwidth and 10 μF in parallel with a 0.1 μF capacitor at rated line voltage and load ranges.
4. Remote inhibit resets OVP latch.
5. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as
a standalone product. EMC compliance to appropriate standards must be veried at the system level. This product is for sale to OEMs and
System Integrators, including through Distribution Channels. It is not intended for sale to End Users.
Note: -C sufx added to the model number indicates cover option.
Notes:
1. Specications subject to change without notice.
2. All dimensions in inches (mm), tolerance is ±0.02”.
3. Specications are for convection rating at factory settings unless otherwise stated.
4. Mounting screw maximum insertion depth is 0.12”.
5. Warranty: 2 years
6. Weight: 1.8 lb/0.85 kg
LPS170-M Series Data Sheet
Mechanical Drawing
7% 7%
LPS170-M Series Data Sheet
WORLDWIDE OFFICES
Americas
2900 S.Diablo Way
Tempe, AZ 85282
USA
+1 888 412 7832
Europe (UK)
Waterfront Business Park
Merry Hill, Dudley
West Midlands, DY5 1LX
United Kingdom
+44 (0) 1384 842 211
Asia (HK)
14/F, Lu Plaza
2 Wing Yip Street
Kwun Tong, Kowloon
Hong Kong
+852 2176 3333
For more information: www.artesyn.com/power
For support: productsupport.ep@artesyn.com
Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and
service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names,
trademarks, or registered trademarks of their respective owners. Specifications subject to change without notice.
© 2016 Artesyn Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, please visit
www.artesyn.com/legal.
www.artesyn.com
LPS170-M Series-DS 10Jul2017
Pin Assignments
Connector LPS17x
SK1 PIN 1 +12 V
PIN 2 5 V Standby
PIN 3 Common
PIN 4 V1 SWP
PIN 5 Common
PIN 6 +V1 sense
PIN 7 Sense common
PIN 8 Remote inhibit
PIN 9 DC power good
PIN 10 POK
SK3 TB-1 COMMON
TB-2 Main output
SK4 PIN 1 GROUND
PIN 3 LINE
Pin 5 NEUTRAL
Mating Connectors
AC Input (SK4)
Molex 09-50-8051 (USA)
Molex 09-91-0500 (UK)
PINS: 08-58-0111
DC Outputs (SK3) Molex 19141-0058
Control Signals (SK1)
Molex 90142-0010 (USA)
PINS: 90119-2110 or
Amp: 87977-3
PINS: 87309-8
Artesyn Embedded Technologies Connector Kit #70-841-016