1 of 18 REV: 080805
GENERAL DESCRIPTION
The DS1673 portable system controller is a circuit
that incorporates many of the functions necessary for
low-power portable products integrated into one chip.
The device provides a real-time clock (RTC), NV
RAM controller, microprocessor monitor, and a
3-channel, 8-bit analog-to-digital converter (ADC).
Communication with the DS1673 is established
through a simple 3-wire interface.
The RTC provides seconds, minutes, hours, day,
date, month, and year information with leap year
compensation. The RTC also provides an alarm
interrupt. This interrupt works when the DS1673 is
powered by the system power supply or when in
battery-backup operation, so the alarm can be used to
wake up a system that is powered down.
Automatic backup and write protection of an external
SRAM is provided through the VCCO, CEOL, and
CEOH pins. The backup energy source used to power
the RTC is also used to retain RAM data in the
absence of VCC through the VCCO pin. The chip-
enable outputs to RAM (CEOL and CEOH) are
controlled during power transients to prevent data
corruption.
ORDERING INFORMATION
PART* VOLTAGE
(V) PIN-
PACKAGE TOP MARK†
DS1673E-3 3.0 20 TSSOP DS1673-3
DS1673E-3+ 3.0 20 TSSOP DS1673-3
DS1673E-5 5.0 20 TSSOP DS1673-5
DS1673E-3/
T&R 3.0 20 TSSOP DS1673-3
DS1673E-3+
T&R 3.0 20 TSSOP DS1673-3
DS1673E-5/
T&R 5.0 20 TSSOP DS1673-5
DS1673S-3 3.0 20 SO DS1673S-3
DS1673S-5 5.0 20 SO DS1673S-5
* All devices are specified over the 0°C to +70°C operating range.
A “‘+” anywhere on the top mark denotes a lead-free device.
+ Denotes a lead(Pb)-free/RoHS-compliant device.
FEATURES
Provides Real-Time Clock
Counts Seconds, Minutes, Hours, Date of the
Month, Month, Day of the Week, and Year
with Leap Year Compensation Valid Up to
2100
Power-Control Circuitry Supports System
Power-On from Day/Time Alarm
Microprocessor Monitor
Halts Microprocessor During Power Fail
Automatically Restarts Microprocessor after
Power Failure
Monitors Pushbutton for External Override
Halts and Resets an Out-of-Control
Microprocessor
NV RAM Control
Automatic Battery Backup and Write Protection
to External SRAM
3-Channel, 8-Bit ADC
Simple 3-Wire Interface
+3.0V or +5.0V Operation
PIN CONFIGURATION
DS1673
Portable System Controlle
r
www.maxim-ic.com
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
S
T
VCC
X1
X2
AIN0
AIN1
AIN2
R
ST
B
LE
B
HE
VBAT
V
CCO
SCLK
I/O
CS
EI
C
EOL
C
EOH
INT
GND
TSSOP (4.4mm)
SO (300 mils)
DS1673
TOP VIEW
DS1673
2 of 18
DETAILED DESCRIPTION
The microprocessor monitor circuitry of the DS1673 provides three basic functions. First, a precision
temperature-compensated reference and comparator circuit monitors the status of VCC. When an out-of-
tolerance condition occurs, an internal power-fail signal is generated which forces the reset to the active
state. When VCC returns to an in-tolerance condition, the reset signals are kept in the active state for
250 ms to allow the power supply and processor to stabilize. The second microprocessor monitor function
is pushbutton reset control. The DS1673 debounces a pushbutton input and guarantees an active reset
pulse width of 250 ms. The third function is a watchdog timer. The DS1673 has an internal timer that
forces the reset signals to the active state if the strobe input is not driven low prior to watchdog timeout.
The DS1673 also provides a 3-channel, 8-bit successive approximation analog-to-digital converter. The
converter has an internal 2.55V (typical) reference voltage generated by an on-board band-gap circuit.
The ADC is monotonic (no missing codes) and has an internal analog filter to reduce high frequency
noise.
OPERATION
The block diagram in Figure 1 shows the main elements of the DS1673. The following paragraphs
describe the function of each pin.
DS1673 BLOCK DIAGRAM Figure 1
DS1673
3 of 18
PIN DESCRIPTION
PIN NAME FUNCTION
1 VBAT Battery Input for Standard 3V Lithium Cell or Other Energy Source
2 VCCO External SRAM Power Supply Output. This pin is internally connected to VCC when
VCC is within nominal limits. However, during power-fail VCCO is internally connected
to the VBAT pin. Switchover occurs when VCC drops below VCCSW.
3 SCLK Serial Clock Input. Used to synchronize data movement on the serial interface.
4 I/O Data Input/Output. This pin is the bidirectional data pin for the 3-wire interface.
5 CS
Chip Select. Must be asserted high during a read or a write for communication over the
3-wire serial interface. CS has an internal 40k pulldown resistor.
6 CEI RAM Chip-Enable In. Must be driven low to enable the external RAM.
7 CEOL RAM Chip-Enable Out Low. Active-low chip-enable output for low-order SRAM
byte.
8 CEOH RAM Chip-Enable Out High. Active-low chip-enable output for high-order SRAM
byte.
9 INT
Interrupt Output. This pin is an active-high output that can be used as an interrupt
input to a microprocessor. The INT output remains high as long as the status bit
causing the interrupt is present and the corresponding interrupt-enable bit is set. The
INT pin operates when the DS1673 is powered by VCC or VBAT.
10 GND Ground. DC power is provided to the device on this pin.
11 BHE Byte High-Enable Input. This pin when driven low activates the CEOH outpu t if CEI
is also driven low.
12 BLE Byte Low-Enable Input. This pin when driven low activates the CEOL output if CEI is
also driven low.
13 RST
Active-Low Reset. The RST pin functions as a microprocessor reset signal. This pin is
driven low 1) when VCC is outside of nominal limits; 2) when the watchdog timer has
timed out; 3) during the power-up reset period; and 4) in response to a pushbutton
reset. The RST pin also functions as a pushbutton reset input. When the RST pin is
driven low, the signal is debounced and timed such that a RST signal of at least 250ms
is generated. This pin has an open-drain output with an internal 47k pullup resistor.
14,
15, 16
AIN2,
AIN1,
AIN0 Analog Inputs. These pins are the three analog inputs for the 3-channel ADC.
17, 18 X2, X1
Connections for Standard 32.768kHz Quartz Crystal. For greatest accuracy, the
DS1673 must be used with a crystal that has a specified load capacitance of 6pF. There
is no need for external capacitors or resistors. Note: X1 and X2 are very high-
impedance nodes. It is recommended that they and the crystal be guard-ringed with
ground and that high frequency signals be kept away from the crystal area. For more
information on crystal selection and crystal layout considerations, refer to Application
Note 58: Crystal Considerations with Dallas Real Time Clocks. The DS1673 does not
function without a crystal.
19 VCC +3.0V or +5.0V Input DC Power
20 ST Active-Low Strobe Input. The strobe input pin is used with the watchdog timer. If the
ST pin is not driven low within the watchdog time period, the RST pin is driven low.
DS1673
4 of 18
POWER-UP/POWER-DOWN CONSIDERATIONS
When VCC is applied to the DS1673 and reaches a level greater than VCCTP (power-fail trip point), the
device becomes fully accessible after tRPU (250ms typical). Before tRPU elapses, all inputs are disabled.
When VCC drops below VCCSW, the device is switched over to the VBAT supply.
During power-up, when VCC returns to an in-tolerance condition, the RST pin is kept in the active state
for 250ms (typical) to allow the power supply and microprocessor to stabilize.
ADDRESS/COMMAND BYTE
The command byte for the DS1673 is shown in Figure 2. Each data transfer is initiated by a command
byte. Bits 0 through 6 specify the address of the registers to be accessed. The MSB (bit 7) is the
Read/Write bit. This bit specifies whether the accessed byte will be read or written. A read operation is
selected if bit 7 is a 0 and a write operation is selected if bit 7 is a one. The address map for the DS1673 is
shown in Figure 3.
ADDRESS/COMMAND BYTE Figure 2
DS1673
5 of 18
DS1673 ADDRESS MAP Figure 3
CLOCK, CALENDAR, AND ALARM
The time and calendar information is accessed by reading/writing the appropriate register bytes. Note that
some bits are set to 0. These bits will always read 0 regardless of how they are written. Also note that
registers 0Fh to 7Fh are reserved. These registers will always read 0 regardless of how they are written.
The contents of the time, calendar, and alarm registers are in the Binary-Coded Decimal (BCD) format.
The DS1673 can run in either 12-hour or 24-hour mode. Bit 6 of the hours register is defined as the 12- or
24-hour mode select bit. When high, the 12-hour mode is selected. In the 12-hour mode, bit 5 is the
AM/PM bit with logic 1 being PM. In the 24-hour mode, bit 5 is the second 10-hour bit (20-23 hours).
The DS1673 also contains a time of day alarm. The alarm registers are located in registers 07h to 0Ah.
Bit 7 of each of the alarm registers are mask bits (see Table 1). When all of the mask bits are logic 0, an
alarm will occur once per week when the values stored in timekeeping registers 00h to 03h match the
values stored in the time of day alarm registers. An alarm will be generated every day when mask bit of
the day alarm register is set to 1. An alarm will be generated every hour when the day and hour alarm
mask bits are set to 1. Similarly, an alarm will be generated every minute when the day, hour, and minute
alarm mask bits are set to 1. When day, hour, minute, and seconds alarm mask bits are set to 1, an alarm
will occur every second.
DS1673
6 of 18
TIME OF DAY ALARM BITS Table 1
ALARM REGISTER MASK BITS (BIT 7)
SECONDS MINUTES HOURS DAYS DESCRIPTION
1 1 1 1 Alarm once per second.
0 1 1 1 Alarm when seconds match.
0 0 1 1 Alarm when minutes and seconds match.
0 0 0 1 Alarm when hours, minutes and seconds match.
0 0 0 0 Alarm when day, hours, minutes and seconds
match.
SPECIAL PURPOSE REGISTERS
The DS1673 has two additional registers (control register and status register) that control the RTC and
interrupts.
CONTROL REGISTER
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
EOSC WP AIS1 AIS0 0 0 0 AIE
EOSC (Enable Oscillator). This bit, when set to logic 0 will start the oscillator. When this bit is set to a
logic 1, the oscillator is stopped and the DS1673 is placed into a low-power standby mode with a current
drain of less than 200nA when in battery-backup mode. When the DS1673 is powered by VCC, the
oscillator is always on regardless of the status of the EOSC bit; however, the RTC is incremented only
when EOSC is a logic 0.
WP (Write Protect). Before any write operation to the RTC or any other registers, this bit must be logic
0. When high, the write protect bit prevents a write operation to any register.
AIS0-AIS1 (Analog Input Select). These 2 bits are used to determine the analog input for the analog-to-
digital conversion. Table 2 lists the specific analog input that is selected by these 2 bits.
AIE (Alarm Interrupt Enable). When set to a logic 1, this bit permits the Interrupt Request Flag (IRQF)
bit in the status register to assert INT. When the AIE bit is set to logic 0, the IRQF bit does not initiate the
INT signal.
ANALOG INPUT SELECTION Table 2
AIS1 AIS0 ANALOG INPUT
0 0 NONE
0 1 AIN0
1 0 AIN1
1 1 AIN2
DS1673
7 of 18
STATUS REGISTER
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
CU LOBAT 0 0 0 0 0 IRQF
CU (Conversion Update In Progress). When this bit is a 1, an update to the ADC Register (register
0Eh) will occur within 488s. When this bit is a 0, an update to the ADC Register will not occur for at
least 244s.
LOBAT (Low Battery Flag). This bit reflects the status of the backup power source connected to the
VBAT pin. When VBAT is greater than 2.5V, LOBAT is set to a logic 0. When VBAT is less than 2.3V,
LOBAT is set to a logic 1.
IRQF (Interrupt Request Flag). A logic 1 in the Interrupt Request Flag bit indicates that the current
time has matched the time of day Alarm registers. If the AIE bit is also a logic 1, the INT pin will go
high. IRQF is cleared by reading or writing to any of the alarm registers.
POWER-UP DEFAULT STATES
These bits are set to a one upon initial power-up: EOSC, TD1 and TD0. These bits are cleared upon
initial power-up: WP, AIS1, and AIS0.
NONVOLATILE SRAM CONTROLLER
The DS1673 provides automatic backup and write protection for external SRAM. This function is
provided by gating the chip enable signals and by providing a constant power supply through the VCCO
pin. The DS1673 was specifically designed with the Intel 80186 and 386EX microprocessors in mind. As
such, the DS1673 has the capability to provide access to the external SRAM in either byte-wide or word-
wide format. This capability is provided by the chip enable scheme. Three input signals and two output
signals are used for enabling the external SRAM(s) (see Figure 4). CEI (chip enable in), BHE (byte high
enable), and BLE (byte low enable) are used for enabling either one or two external SRAMs through the
CEOL (chip enable low) and the CEOH (chip enable high) outputs. Table 3 illustrates the function of
these pins.
The DS1673 nonvolatilizes the external SRAM(s) by write-protecting the SRAM(s) and by providing a
back-up power supply in the absence of VCC. When VCC falls below VPF, access to the external SRAM(s)
are prohibited by forcing CEOL and CEOH high regardless of the level of CEI , BLE , and BHE . Upon
power-up, access is prohibited until the end of tRPU.
EXTERNAL SRAM CHIP ENABLE Table 3
CEI BHE BLE CEOL CEOH FUNCTION
0 0 0 0 0 Word transfer
0 0 1 1 0 Byte transfer in upper half of data bus (D15-D8)
0 1 0 0 1 Byte transfer in lower half of data bus (D7-D0)
0 1 1 1 1 External SRAMs disabled
1 X X 1 1 External SRAMs disabled
DS1673
8 of 18
EXTERNAL SRAM INTERFACE (WORD-WIDE) TO THE DS1673 Figure 4
MICROPROCESSOR MONITOR
The DS1673 monitors three vital conditions for a microprocessor: power supply, software execution, and
external override.
First, a precision temperature-compensated reference and comparator circuit monitors the status of VCC.
When an out-of-tolerance condition occurs, an internal power-fail signal is generated which forces the
RST pin to the active state, thus warning a processor-based system of impending power failure. When
VCC returns to an in-tolerance condition upon power-up, the reset signal is kept in the active state for
250ms (typical) to allow the power supply and microprocessor to stabilize. Note, however, that if the
EOSC bit is set to a logic 1 (to disable the oscillator during battery-backup mode), the reset signal will be
kept in an active state for 250 ms plus the start-up time of the oscillator.
The second monitoring function is push-button reset control. The DS1673 provides for a pushbutton
switch to be connected to the RST output pin. When the DS1673 is not in a reset cycle, it continuously
monitors the RST signal for a low going edge. If an edge is detected, the DS1673 will debounce the
switch by pulling the RST line low. After the internal 250ms timer has expired, the DS1673 will continue
to monitor the RST line. If the line is still low, the DS1673 will continue to monitor the line looking for a
rising edge. Upon detecting release, the DS1673 will force the RST line low and hold it low for 250ms.
The third microprocessor monitoring function provided by the DS1673 is a watchdog timer. The
watchdog timer function forces RST to the active state when the ST input is not stimulated within the
predetermined time period. The time period is set by the Time Delay (TD) bits in the Watchdog Register.
The time delay can be set to 250ms, 500ms, or 1000ms (see Figure 5). If TD0 and TD1 are both set to
zero, the watchdog timer is disabled. When enabled, the watchdog timer starts timing out from the set
time period as soon as RST is inactive. The default setting is for the watchdog timer to be enabled with
1000ms time delay. If a high-to-low transition occurs on the ST input pin prior to time-out, the watchdog
timer is reset and begins to time-out again. If the watchdog timer is allowed to time-out, then the RST
signal is driven to the active state for 250ms (typical). The ST input can be derived from microprocessor
address signals, data signals, and/or control signals. To guarantee that the watchdog timer does not time-
out, a high-to-low transition must occur at or less than the minimum period.
DS1673
9 of 18
WATCHDOG TIME-OUT CONTROL Figure 5
WATCHDOG REGISTER
BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0
0 0 0 0 0 0 TD1 TD0
WATCHDOG REGISTER
TD1 TD0 WATCHDOG TIME-OUT
0 0 WATCHDOG DISABLED
0 1 250 ms
1 0 500 ms
1 1 1000 ms
ANALOG-TO-DIGITAL CONVERTER
The DS1673 provides a 3-channel, 8-bit analog-to-digital converter. The ADC reference voltage (2.55V
typical) is derived from an on-chip band-gap circuit. Three multiplexed analog inputs are provided
through the AIN0, AIN1, and AIN2 pins. The ADC is monotonic (no missing codes) and uses a
successive approximation technique to convert the analog signal into a digital code.
An A/D conversion is the process of assigning a digital code to an analog input voltage. This code
represents the input value as a fraction of the full-scale voltage (FSV) range. Thus, the FSV range is then
divided by the ADC into 256 codes (8 bits). The FSV range is bounded by an upper limit equal to the
reference voltage and the lower limit, which is ground. The DS1673 has a FSV of 2.55V (typical) that
provides a resolution of 10mV. An input voltage equal to the reference voltage converts to FFh while an
input voltage equal to ground converts to 00h. The relative linearity of the ADC is 0.5 LSB.
The A/D converter selects from one of three different analog inputs (AIN0–AIN2). The input that is
selected is determined by the Analog Input Select (AIS) bits in the Control Register. Table 2 lists the
specific analog input that is selected by these 2 bits. Note also that the converter can be turned off by
these bits to reduce power. When the ADC is turned on by setting AIS0 and AIS1 to any value other than
0,0 the analog input voltage is converted and written to the ADC Register within 488s. An internal
analog filter at the input reduces high frequency noise. Subsequent updates occur approximately every
10ms. If AIS0 and/or AIS1 are changed, updates will occur at the next 10 ms conversion time.
The Conversion Update In Progress (CU) bit in the Status Register indicates when the ADC Register can
be read. When this bit is a 1, an update to the ADC Register will occur within 488s maximum. However,
when this bit is 0 an update will not occur for at least 244s. The CU bit should be polled before reading
the ADC Register to insure that the contents are stable during a read cycle. Once a read cycle to the ADC
Register has been started, the DS1673 will not update that register until the read cycle has been
completed. It should also be mentioned that taking CS low will abort the read cycle and will allow the
ADC Register to be updated.
Figure 6 illustrates the timing of the CU bit relative to an instruction to begin conversion and the
completion of that conversion.
DS1673
10 of 18
CU BIT TIMING Figure 6
3-WIRE SERIAL INTERFACE
Communication with the DS1673 is accomplished through a simple 3-wire interface consisting of the
Chip Select (CS), Serial Clock (SCLK) and Input/Output (I/O) pins.
All data transfers are initiated by driving the CS input high. The CS input serves two functions. First, CS
turns on the control logic, which allows access to the shift register for the address/command sequence.
Second, the CS signal provides a method of terminating either single byte or multiple byte (burst) data
transfer. A clock cycle is a sequence of a rising edge followed by a falling edge. For data input, data must
be valid during the rising edge of the clock and data bits are output on the falling edge of the clock. If the
CS input goes low, all data transfer terminates and the I/O pin goes to a high impedance state.
Address and data bytes are always shifted LSB first into the I/O pin. Any transaction requires the
address/command byte to specify a read or write to a specific register followed by 1 or more bytes of
data. The address byte is always the first byte entered after CS is driven high. The most significant bit
(RD /WR) of this byte determines if a read or write will take place. If this bit is 0, one or more read cycles
will occur. If this bit is 1, one or more write cycles will occur.
Data transfers can occur 1 byte at a time or in multiple byte burst mode. After CS is driven high an
address is written to the DS1673. After the address, 1 or more data bytes can be read or written. For a
single-byte transfer 1 byte is read or written and then CS is driven low. For a multiple-byte transfer,
multiple bytes can be read or written to the DS1673 after the address has been written. Each read or write
cycle causes the register address to automatically increment. Incrementing continues until the device is
disabled. After accessing register 0Eh, the address wraps to 00h.
Data transfer for single-byte transfer and multiple-byte bu rst transfer is illustrated in Figures 7 and 8.
DS1673
11 of 18
SINGLE-BYTE DATA TRANSFER Figure 7
MULTIPLE-BYTE BURST TRANSFER Figure 8
DS1673
12 of 18
ABSOLUTE MAXIMUM RATINGS
Voltage on Any Pin Relative to Ground…………………………………………………….-0.3V to +7.0V
Operating Temperature………………………………………………………………………..0°C to +70°C
Storage Temperature……………………………………………………………………….-55°C to +125°C
Soldering Temperature………………………………………………………..See J-STD-020 Specification
This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the
operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of
time may affect device reliability.
RECOMMENDED DC OPERATING CONDITIONS (TA = 0C to +70C)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
5.0V 4.5 5.0 5.5
Power Supply Voltage 3.0V VCC 2.7 3.0 3.3 V 1
Input Logic 1 VIH 2.0 VCC+0.3 V 1
Input Logic 0 VIL -0.3 +0.8 V 1
Battery Voltage VBAT 2.5 3.7 V 1
DC ELECTRICAL CHARACTERISTICS (VCC = 5.0V ± 10%, TA = 0C to +70C.)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
Input Leakage ILI -1 +1
A
CS Leakage ILO 150
A 7
Logic 1 Output (IOUT = -0.4mA) VOH 2.4 V 2
Logic 0 Output (IOUT = 1.5mA) VOL 0.4 V 3
Active Supply Current (CS = VCC - 0.2) ICCA 1.5 2.0 mA 4
A/D Converter Current IADC 500
A 5
Standby Current (CS = VIL) ICCS 300
A 6
Battery Current (Oscillator On) IBAT1 300 500 nA
Battery Current (Oscillator Off) IBAT2 200 nA
Internal RST Pullup Resistor RP 35 47 60
k
VCC Trip Point VCCTP 4.25 4.35 4.50 V
VCC Switchover VCCSW 2.60 2.70 2.80 V 12
A/D Reference Voltage VADC 2.47 2.55 2.63 V
Pushbutton Detect PBDV 0.8 2.0 V
Pushbutton Release PBRD 0.3 0.8 V
Output Voltage VCCO V
CC-0.3 V 11
VCCO Output Current (Source = VCC) ICCO1 150 mA 13
VCCO Output Current (Source = VBAT) ICCO2 150
A 14
DS1673
13 of 18
DC ELECTRICAL CHARACTERISTICS (VCC = 3.0V ±10%, TA = 0C to +70C.)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
Input Leakage ILI -1 +1
A
CS Leakage ILO 150
A 7
Logic 1 Output (IOUT =-0.4mA) VOH 2.4 V 2
Logic 0 Output (IOUT = 1.5mA) VOL 0.4 V 3
Active Supply Current (CS = VCC - 0.2) ICCA 0.75 1.0 mA 4
ADC Current IADC 200
A 5
Standby Current (CS = VIL) ICCS 100
A 6
Battery Current (Oscillator On) IBAT1 300 500 nA
Battery Standby Current (Oscillator Off) IBAT2 200 nA
Internal RST Pullup Resistor RP 35 47 60
k
VCC Trip Point VCCTP 2.5 2.6 2.7 V
VCC Switchover VCCSW 2.30 2.40 2.50 V 12
A/D Reference Voltage VADC 2.47 2.55 2.63 V
Pushbutton Detect PBDV 0.8 2.0 V
Pushbutton Release PBRD 0.3 0.8 V
Output Voltage VCCO V
CC-0.3 V 11
VCCO Output Current (Source = VCC) ICCO1 80 mA 13
VCCO Output Current (Source = VBAT) ICCO2 100
A 14
CAPACITANCE (TA = +25C)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
Input Capacitance CI 10 pF
I/O Capacitance CI/O 15 pF
Crystal Capacitance CX 6 pF
DS1673
14 of 18
AC ELECTRICAL CHARACTERISTICS (VCC = 5.0V ±10%, TA = 0C to 70C.)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
Data to Clock Setup tDC 50 ns 8
CLK to Data Hold tCDH 70 ns 8
CLK to Data Delay tCDD 200 ns 8, 9, 10
CLK to Low Time tCL 250 ns 8
CLK to High Time tCH 250 ns 8
CLK Frequency tCLK 2.0 MHz 8
CLK Rise and Fall tR, tF 500 ns
CS to CLK Setup tCC 1 s 8
CLK to CS Hold tCCH 60 ns 8
CS Inactive Time tCWH 1 s 8
CS to I/O High-Z tCDZ 70 ns 8
VCC Slew Rate (4.5V to 2.3V) tF 1 ms
VCC Slew Rate (2.3V to 4.5V) tR 0 ns
VCC Detect to RST (VCC Falling) tRPD 100 ns
Reset Active Time tRST 250 ms 15
Pushbutton Debounce PBDB 250 ms 15
VCC Detect to RST (VCC Rising) tRPU 250 ms 15, 16
ST Pulse Width tST 20 ns
Chip Enable Propagation Delay to
External SRAM tCED 8 15 ns
Nominal Voltage to VCC Switchover
Fall Time tFB 200 s
DS1673
15 of 18
AC ELECTRICAL CHARACTERISTICS (VCC = 3.0V ±10%, TA = 0C to +70C.)
PARAMETER SYMBOL MIN TYP MAX UNITS NOTES
Data to Clock Setup tDC 150 ns 8
CLK to Data Hold tCDH 210 ns 8
CLK to Data Delay tCDD 600 ns 8, 9, 10
CLK to Low Time tCL 750 ns 8
CLK to High Time tCH 750 ns 8
CLK Frequency tCLK 0.667 MHz 8
CLK Rise and Fall tR, tF 1500 ns
CS to CLK Setup tCC 3 s 8
CLK to CS Hold tCCH 180 ns 8
CS Inactive Time tCWH 3 s 8
CS to I/O High-Z tCDZ 210 ns 8
VCC Slew Rate (2.7V to 2.3V) tF 300 s
VCC Slew Rate (2.3V to 2.7V) tR 0 ns
VCC Detect to RST (VCC Falling) tRPD 200 ns
Reset Active Time tRST 250 ms 15
Pushbutton Debounce PBDB 250 ms 15
VCC Detect to RST (VCC Rising) tRPU 250 ms 15, 16
ST Pulse Width tST 40 ns
Chip Enable Propagation Delay to
External SRAM tCED 8 25 ns
Nominal Voltage to VCC Switchover
Fall Time tFB 300 s
DS1673
16 of 18
TIMING DIAGRAM: READ DATA Figure 9
TIMING DIAGRAM: WRITE DATA Figure 10
DS1673
17 of 18
PUSHBUTTON RESET Figure 11
POWER-UP Figure 12
POWER-DOWN Figure 13
DS1673
18 of 18
Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.
No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2005 Maxim Integrated Products
The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.
NOTES:
1. All voltages are referenced to ground.
2. Logic 1 voltages are specified at VCC = 3.0V, VOH = VCC for capacitive loads. Excludes RST pin
3. Logic 0 voltages are specified at VCC = 3.0V, VOL = GND for capacitive loads.
4. ICCA is specified with outputs open, CS set to a logic 1, SCLK = 500kHz, oscillator enabled, and
D/A converter enabled.
5. IADC is specified with CS, VCCO open and I/O, SCLK at logic 0. ADC is enabled.
6. ICCS is specified with CS, VCCO open and I/O, SCLK at logic 0. ADC is disabled.
7. CS has a 40k pulldown resistor to ground.
8. Measured at VIH = 2.0V or VIL = 0.8V and 10ns maximum rise and fall time.
9. Measured at VOH = 2.4V or VOL = 0.4V.
10. Load capacitance = 25pF.
11. ICCO = 100mA, VCC > VCCTP.
12. VCCO switchover from VCC to VBAT occurs when VCC drops below the lower of VCCSW and VBAT.
13. Current from VCC input pin to VCCO output pin.
14. Current from VBAT input pin to VCCO output pin.
15. Time base is generated by very accurate crystal oscillator. Accuracy of this time period is based on
the crystal that is used. A typical crystal with a specified load capacitance of 6pF will provide an
accuracy within ±100ppm over the 0°C to +70°C temperature range.
16. If the EOSC bit in the Control Register is set to a logic 1, tRPU is equal to 250ms plus the startup
time of the crystal oscillator.
PACKAGE INFORMATION
For the latest package outline information and land patterns, go to www.maxim-ic.com/packages.
PACKAGE TYPE PACKAGE CODE DOCUMENT NO.
20 TSSOP U20+1 21-0066
20 SO W20+3 21-0042
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Maxim Integrated:
DS1673E-3+ DS1673E-3+T&R DS1673E-5+ DS1673E-5+T&R DS1673S-3+ DS1673S-5+ DS1673S-5+T&R