MICROCIRCUIT DATA SHEET Original Creation Date: 04/20/00 Last Update Date: 06/11/04 Last Major Revision Date: 04/20/00 MRLM111-X-RH REV 0E1 VOLTAGE COMPARATOR: ALSO AVAILABLE GUARANTEED TO 30k rd(Si) TESTED TO MIL-STD-883, METHOD 1019 General Description The LM111, is a voltage comparator that has input currents nearly a thousand times lower than devices such as the LM106 and LM710. It is also designed to operate over a wider range of supply voltages: from standard +15V op amp supplies down to the single 5V supply used for IC logic. Its output is compatible with RTL, DTL and TTL as well as MOS circuits. Further, it can drive lamps or relays, switching voltages up to 50V at currents as high as 50mA. Both the inputs and the outputs of the LM111, can be isolated from system ground, and the output can drive loads referred to ground, the positive supply or the negative supply. Offset balancing and strobe capability are provided and outputs can be wire OR'ed. Although slower than the LM106 and LM710 (200 ns response time vs 40ns) the devices are also much less prone to spurious oscillations. The LM111 has the same pin configuration as the LM106 and LM710. Industry Part Number NS Part Numbers LM111 LM111HPQMLV LM111J-8PQMLV LM111WGPQMLV LM111WPQMLV Prime Die LM111 Controlling Document SEE FEATURES SECTION Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MRLM111-X-RH REV 0E1 Features - Low Input Bias Current. Low Input Offset Current. Wide Differential Input Voltage. Power Supply Voltage, Single 5V to +15V. Offset Voltage Null Capability. Strobe Capability CONTROLLING DOCUMENTS: LM111HPQMLV 5962P0052401VGA LM111J-8PQMLV 5962P0052401VPA LM111WGPQMLV 5962P0052401VZA LM111WPQMLV 5962P0052401VHA 2 MICROCIRCUIT DATA SHEET MRLM111-X-RH REV 0E1 (Absolute Maximum Ratings) (Note 1) Positive Supply Voltage +30.0V Negative Supply Voltage -30.0V Total Supply Voltage 36V Output to Negative Supply Voltage 50V GND to Negative Supply Voltage 30V Differential Input Voltage +30V Sink Current 50mA Input Voltage (Note 2) +15V Power Dissipation (Note 3) 8 Lead METAL CAN 8 Lead CERDIP 10 Lead CERPACK 10 Lead CERAMIC SOIC Output Short Circuit Duration 330mW 400mW 330mW 330mW at at at at 25 25 25 25 C C C C 10 sec. Maximum Strobe Current 10mA Operating Temperature Range -55 C < Ta < +125 C Thermal Resistance ThetaJA 8 Lead METAL CAN 8 Lead CERDIP 10 Lead CERPACK 10 Lead CERAMIC SOIC (Still Air (500LF/Min (Still Air (500LF/Min (Still Air (500LF/Min (Still Air (500LF/Min @ 0.5W) Air flow @ 0.5W) Air flow @ 0.5W) Air flow @ 0.5W) Air flow ThetaJC 8 Lead METAL CAN 8 Lead CERDIP 10 Lead CERPACK 10 Lead CERAMIC SOIC Storage Temperature Range @ 0.5W) @ 0.5W) @ 0.5W) @ 0.5W) 162 92 134 76 231 153 231 153 C/W C/W C/W C/W C/W C/W C/W C/W 50 21 24 24 C/W C/W C/W C/W -65 C < Ta < +150 C Maximum Junction Temperature 175 C Lead Temperature (Soldering, 60 seconds) Voltage at Strobe Pin 300 C V+ -5V Package Weight (Typical) 8 Lead METAL CAN 8 Lead CERDIP 10 Lead CERPACK 10 Lead CERAMIC SOIC 965mg 1100mg 250mg 225mg 3 MICROCIRCUIT DATA SHEET MRLM111-X-RH REV 0E1 (Absolute Maximum Ratings) (Continued) (Note 1) ESD Rating (Note 4) 300V Note 1: Note 2: Note 3: Note 4: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. This rating applies for +15V supplies. The positive input voltage limits is 30V above the negative supply. The negative input voltage limits is equal to the negative supply voltage or 30V below the positive supply, whichever is less. The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is Pdmax = (Tjmax - TA)/ThetaJA or the number given in the Absolute Maximum Ratings, whichever is lower. Human body model, 1.5k Ohms in series with 100pF. Recommended Operating Conditions Supply Voltage Vcc = +15Vdc Operating Temperature Range -55 C < Ta < +125 C 4 MICROCIRCUIT DATA SHEET MRLM111-X-RH REV 0E1 Electrical Characteristics DC PARAMETERS: (SEE NOTE 8) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +15V, Vcm = 0V SYMBOL Vio PARAMETER Input Offset Voltage CONDITIONS NOTES Vin = 0V, Rs = 50 Ohms +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50 Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50 Ohms +Vcc = +2.5V, -Vcc = -2.5V, Vin = 0V, Rs = 50 Ohms Vio(R) Raised Input Offset Voltage Vin = 0V, Rs = 50 Ohms +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50 Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50 Ohms Iio Input Offset Current Vin = 0V, Rs = 50K Ohms +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50K Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50K Ohms Iio(R) Iib+ Raised Input Offset Current Input Bias Current Vin = 0V, Rs = 50K Ohms Vin = 0V, Rs = 50K Ohms +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50K Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50K Ohms 5 PINNAME MIN MAX UNIT SUBGROUPS -3 +3 mV 1 -4 +4 mV 2, 3 -3 +3 mV 1 -4 +4 mV 2, 3 -3 +3 mV 1 -4 +4 mV 2, 3 -3 +3 mV 1 -4 +4 mV 2, 3 -3 +3 mV 1 -4.5 +4.5 mV 2, 3 -3 +3 mV 1 -4.5 +4.5 mV 2, 3 -3 +3 mV 1 -4.5 +4.5 mV 2, 3 -10 +10 nA 1, 2 -20 +20 nA 3 -10 +10 nA 1, 2 -20 +20 nA 3 -10 +10 nA 1, 2 -20 +20 nA 3 -25 +25 nA 1, 2 -50 +50 nA 3 -100 0.1 nA 1, 2 -150 0.1 nA 3 -150 0.1 nA 1, 2 -200 0.1 nA 3 -150 0.1 nA 1, 2 -200 0.1 nA 3 MICROCIRCUIT DATA SHEET MRLM111-X-RH REV 0E1 Electrical Characteristics DC PARAMETERS: (SEE NOTE 8) (Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +15V, Vcm = 0V SYMBOL Iib- PARAMETER Input Bias Current CONDITIONS NOTES Vin = 0V, Rs = 50K Ohms +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50K Ohms +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50K Ohms MIN MAX UNIT SUBGROUPS -100 0.1 nA 1, 2 -150 0.1 nA 3 -150 0.1 nA 1, 2 -200 0.1 nA 3 -150 0.1 nA 1, 2 -200 0.1 nA 3 14 V 1, 2, 3 80 dB 1, 2, 3 Vo(STB) Collector Output Voltage (ST) Vin+ = Gnd, Vin- = 15V, Istb = -3mA, Rs = 50 Ohms CMR Common Mode Rejection -28V<-Vcc<-0.5V, Rs=50 Ohms, 2V<+Vcc<29.5V, Rs=50 Ohms, -14.5V<Vcm<13V,Rs=50 Ohms Vol Low Level Output Voltage +Vcc = 4.5V, -Vcc = Gnd, Iout = 8mA, +Vin = 0.5V, Vid = -6mV 0.4 V 1, 2, 3 +Vcc = 4.5V, -Vcc = Gnd, Iout = 8mA, +Vin = 3V, Vid = -6mV 0.4 V 1, 2, 3 Iout = 50mA, +Vin = 13V, Vid = -5mV 1.5 V 1, 2, 3 Iout = 50mA, +Vin = -14V, Vid = -5mV 1.5 V 1, 2, 3 -1 10 nA 1 -1 500 nA 2 Icex Ii Icc+ Icc- Output Leakage Current Input Leakage Current 1 PINNAME +Vcc = 18V, -Vcc = -18V, Vout = 32V +Vcc = 18V, -Vcc = -18V, +Vin = +12V, -Vin = -17V 7 -5 500 nA 1, 2, 3 +Vcc = 18V, -Vcc = -18V, +Vin = -17V, -Vin = +12V 7 -5 500 nA 1, 2, 3 6 mA 1, 2 7 mA 3 -5 mA 1, 2 -6 mA 3 Power Supply Current Power Supply Current Delta Vio/Delta T Temperature Coefficient Input Offset Voltage 25 C < T < 125 C -25 25 uV/ C 2 -55 C < T < 25 C -25 25 uV/ C 3 Delta Iio/Delta T Temperature Coefficient Input Offset Current 25 C < T < 125 C -100 100 pA/ C 2 -55 C < T < 25 C -200 200 pA/ C 3 6 MICROCIRCUIT DATA SHEET MRLM111-X-RH REV 0E1 Electrical Characteristics DC PARAMETERS: (SEE NOTE 8) (Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +15V, Vcm = 0V SYMBOL Ios PARAMETER Short Circuit Current CONDITIONS NOTES Vout = 5V, t < 10mS, Vin- = 0.1V, Vin+ = 0V PINNAME MIN MAX UNIT SUBGROUPS 3, 5 200 mA 1 3, 5 150 mA 2 3, 5 250 mA 3 mV 1 mV 1 Vio(adj)+ Input Offset Voltage (Adjustment) Vout = 0V, Vin = 0V, Rs = 50 Ohms 3 Vio(adj)- Input Offset Voltage (Adjustment) Vout = 0V, Vin = 0V, Rs = 50 Ohms 3 Ave+ Voltage Gain (Emitter) Rl = 600 Ohms 3, 6 10 V/mV 4 3, 6 8 V/mV 5, 6 3, 6 10 V/mV 4 3, 6 8 V/mV 5, 6 Ave- Voltage Gain (Emitter) Rl = 600 Ohms 5 -5 AC PARAMETERS: (SEE NOTE 8) (The following conditions apply to all the following parameters, unless otherwise specified.) AC: +Vcc = +15V, Vcm = 0 trLHC trHLC Response Time (Collector Output) Vod(Overdrive) = -5mV, Cl = 50pF, Vin = -100mV Response Time (Collector Output) Vod(Overdrive) = 5mV, Cl = 50pF, Vin = 100mV 7 4 300 nS 7, 8B 4 640 nS 8A 4 300 nS 7, 8B 4 500 nS 8A MICROCIRCUIT DATA SHEET MRLM111-X-RH REV 0E1 Electrical Characteristics DC PARAMETERS: DRIFT VALUES (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +15V, Vcm = 0V. "Delta calculations performed on JAN S and QMLV devices at group B, subgroup 5 only". SYMBOL Vio Iib+ Iib- Icex PARAMETER Input Offset Voltage Input Bias Current Input Bias Current Output Leakage Current Note 1: Note 2: Note 3: Note Note Note Note Note 4: 5: 6: 7: 8: CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Vin = 0V, Rs = 50 Ohms -0.5 0.5 mV 1 +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50 Ohms -0.5 0.5 mV 1 +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50 Ohms -0.5 0.5 mV 1 Vin = 0V, Rs = 50K Ohms -12.5 12.5 nA 1 +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50K Ohms -12.5 12.5 nA 1 +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50K Ohms -12.5 12.5 nA 1 Vin = 0V, Rs = 50K Ohms -12.5 12.5 nA 1 +Vcc = 29.5V, -Vcc = -0.5V, Vin = 0V, Vcm = -14.5V, Rs = 50K Ohms -12.5 12.5 nA 1 +Vcc = 2V, -Vcc = -28V, Vin = 0V, Vcm = +13V, Rs = 50K Ohms -12.5 12.5 nA 1 +Vcc = 18V, -Vcc = -18V, Vout = 32V -5 5 nA 1 Istb = -2mA at -55 C. Calculated parameter. Use DC tape for Ios and Vio(adj), Ave+ and Ave- as indicated in TAPE NAME section of this JRETS. Uses AC tape and hardware. Actual min. limit used is 5mA due to test setup. Datalog reading in K = V/mV. Vid is voltage difference between inputs. Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiaton end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, Method 1019.5, Condition A. 8 MICROCIRCUIT DATA SHEET MRLM111-X-RH REV 0E1 Graphics and Diagrams GRAPHICS# DESCRIPTION 05172HRB2 METAL CAN (H), TO-99, 8LD .200 DIA P.C. (B/I CKT) 05174HRC2 CERPACK (W), 10 LEAD (B/I CKT) 05284HRC2 METAL CAN (H), TO-99, 3LD .200 DIA P.C. (B/I CKT) 05652HRA2 CERDIP (J), 8 LEAD (B/I CKT) 09569HRC2 CERPACK (W), 10 LEAD (B/I CKT) H08CRF METAL CAN (H), TO-99, 8LD .200 DIA P.C. (P/P DWG) J08ARL CERDIP (J), 8 LEAD (P/P DWG) P000264A METAL CAN (H), 8 LEAD (PINOUT) P000265A CERDIP (J), 8 LEAD (PINOUT) P000267A CERPACK (W), 10 LEAD (PINOUT) P000373A CERAMIC SOIC (WG), 10 LEAD (PINOUT) W10ARG CERPACK (W), 10 LEAD (P/P DWG) WG10ARC CERPACK (WG), 10 LEAD (P/P DWG) See attached graphics following this page. 9 N N N N MICROCIRCUIT DATA SHEET MRLM111-X-RH REV 0E1 Revision History Rev ECN # Originator Changes 0A0 M0003685 05/22/00 Rel Date Rose Malone Initial MDS Release: MRLM111-X-RH, Rev. 0A0 0B0 M0003692 04/08/02 Rose Malone Update MDS: MRLM111-X-RH, Rev. 0A0 to MRLM111-X-RH, Rev. 0B0. Typo in Recommended Operating Section. 0C0 M0003988 03/10/03 Rose Malone Update MDS: MRLM111-X-RH, Rev. 0B0 to MRLM111-X-RH, Rev. 0C0. Deleted reference for the following NSID's from Main Table, Features Section and Graphics Section. LM111HPQML , LM111HPQMLV, LM111J-8PQML, LM111WGPQML product un-available. 0D1 M0004136 06/11/04 Rose Malone Update MDS: MRLM111-X-RH, Rev. 0C0 to MRLM111-X-RH, Rev. 0D1. Added W package reference to Main Table, Features Section, Absolute Maximum Ratings Section and Graphics Section. 0E1 M0004387 06/11/04 Rose Malone Update MDS: MRLM111-X-RH, Rev. 0D1 to REV. 0E1. Added to Main Table, Features Section, Absolute Maximum Ratings Section and Graphics Section information pertaining to NSID: LM111HPQMLV 10