Panel Mount Datasheet EZ Series * Compact design for low-profile applications; Ratings from 5 A to 18 A @ 600 VAC * SCR output for heavy industrial loads * AC or DC control * 1/4" fast-on terminals for easy installation * UL/CSA/VDE Approved, CE Compliant to EN60950-1 PRODUCT SELECTION 5A 12 A 18 A EZ240D5 EZ240D12 EZE240D12 EZ240D18 EZE240D18 Control Voltage 3-15 VDC 15-32 VDC 90-140 Vrms EZ240A12 EZ240A18 18-36 Vrms 4-15 VDC 15-32 VDC EZE240A12 EZ480D12 EZE480D12 EZE240A18 EZ480D18 EZE480D18 90-140 Vrms EZ480A12 EZ480A18 18-36 Vrms EZE480A12 EZE480A18 AVAILABLE OPTIONS Control Voltage Input Range Blank: Standard Input D: DC 3-15 V (4-15 V for E: 18-36 VAC (AC Input) 480 V) 15-32 VDC (DC Input) A: AC 90-140 V Series EZ E 240 A 12 Operating Voltage 240: 24-280 VAC 480: 48-660 VAC Internal Snubber Blank: Not Included S: Included (EZ240 only) S Load Current 5: 5 Amps (EZ240D suffix only) R Switching Mode Blank: Zero Voltage Turn-On -10: Random Turn-On 12: 12 Amps 18: 18 Amps Required for valid part number For options only and not required for valid part number OUTPUT SPECIFICATIONS (1) Description Operating Voltage (47-63Hz) [Vrms] Transient Overvoltage [Vpk] Maximum Off-State Leakage Current @ Rated Voltage [mArms] (4) Minimum Off-State dv/dt @ Maximum Rated Voltage [V/sec] (2) Maximum Load Current [Arms] (3) Minimum Load Current [Arms] Maximum 1 Cycle Surge Current (50/60Hz) [Apk] Maximum On-State Voltage Drop @ Rated Current [Vpk] Thermal Resistance Junction to Case (Rjc) [C/W] Maximum 1/2 Cycle It for Fusing (50/60 Hz) [A sec] Minimum Power Factor (with Maximum Load) 5A 12 A 18 A 12 A 18 A 24-280 600 0.1 500 5 150 38/40 1.5 2 102/93 0.5 24-280 600 0.1 500 12 150 143/150 1.5 2 102/93 0.5 24-280 600 0.1 500 18 150 191/200 1.5 1.1 182/166 0.5 48-660 1200 0.1 500 12 150 143/150 1.5 2 102/93 0.5 48-660 1200 0.1 500 18 150 191/200 1.5 1.1 182/166 0.5 Do not forget to visit us at: www.crydom.com Copyright (c) 2017 Crydom Inc. Specifications subject to change without notice. Panel Mount Datasheet INPUT SPECIFICATIONS (1) Description EZ240Dxx EZ480Dxx EZExxxDxx EZxxxAxx EZExxxAxx 3-15 VDC 3.0 VDC 1.0 VDC 5.0 VDC 15 mAdc 300 Ohm 1/2 Cycle 1/2 Cycle 4-15 VDC 4.0 VDC 1.0 VDC 5.0 VDC 15 mAdc 240 Ohm 1/2 Cycle 1/2 Cycle 15-32 VDC 15.0 VDC 1.0 VDC 24 VDC 15 mAdc 1500 Ohm 1/2 Cycle 1/2 Cycle 90-140 Vrms 90.0 Vrms 10.0 Vrms 120 Vrms 10 mA 10.6 k Ohm 1/2 Cycle 1/2 Cycle 18-36 Vrms 18.0 Vrms 2.0 Vrms 24 Vrms 10 mA 1.8 k Ohm 1/2 Cycle 1/2 Cycle Control Voltage Range Minimum Turn-On Voltage Minimum Turn-Off Voltage Nominal Voltage Typical Input Current @ Nominal Voltage Nominal Input Impedance Maximum Turn-On Time [msec] (5) Maximum Turn-Off Time [msec] GENERAL SPECIFICATIONS (1) Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) 2500 Vrms 109 Ohm 8 pF -40 to 80C -40 to 125 C 1.5 oz (43 g) Thermally Conductive Epoxy .25" Fastons 8-14/1.1-1.5 Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) Encapsulation Terminals Mounting Screw Torque (8-32 UNC screw) [in lbs/Nm] GENERAL NOTES (1) All parameters at 25C unless otherwise specified. (2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 (3) Heat sinking required, see derating curves. (4) Off- state leakage for snubbered version (suffix S, 240V version only) is 10.0mArms (5) Turn-on time for random turn-on versions is 0.1 msec (DC Control Models). WIRING DIAGRAM -DC 4 SNUBBER TRIGGER CIRCUIT +DC A 1 LOAD AC 2 LOAD AC * 3 B *Snubber option offered in 240 V version only. Load can be wired in location A or B AC 4 AC TRIGGER CIRCUIT SNUBBER AC/DC CONVERTER LOAD AC 2 LOAD AC * 3 *Snubber option offered in 240 V version only. Do not forget to visit us at: www.crydom.com A 1 Copyright (c) 2017 Crydom Inc. Specifications subject to change without notice. B Panel Mount Datasheet MECHANICAL SPECIFICATIONS 2.63 (66.8) .197 DIA. (2 PLCS) 2.24 (56.9) Tolerances: 0.02 in / 0.5 mm All dimensions are in: inches [millimeters] 1.50 .49 (38.1) (12.4) 1.00 (25.4) FASTON TERMINAL .250 X .032 4 PLCS. 1.73 (43.9) .40 (10.2) .12 (3.0) .95 (24.1) THERMAL DERATE INFORMATION 115 3 2 120 1 1 2 3 4 Load Current [Arms] 5 Power Dissipation [W] 110 Base Plate Temp [C] Power Dissipation 6 5 4 12 A 15 112 10 116 5 120 124 2 10 20 40 60 80 4 6 8 Load Current [Arms] Max Ambient Temp. [C] 10 12 20 40 60 Base Plate Temp [C] 5 C/W 10 C/W NO HEATSINK 5A 2 C/W 4 C/W 6 C/W NO HEATSINK 80 Max Ambient Temp. [C] 18 112 12 116 6 120 124 3 6 9 12 15 18 20 40 60 Load Current [Arms] AGENCY APPROVALS Base Plate Temp [C] Power Dissipation [W] 18 A 2 C/W 5 C/W NO HEATSINK 80 Max Ambient Temp. [C] Agency Approvals Designed in accordance with the requirements of IEC 62314 EN60950 : Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7: E116950 LR81689 10139 UG (240 VDC Control Only) Rev. 090517 ECN 20309 Do not forget to visit us at: www.crydom.com Copyright (c) 2017 Crydom Inc. Specifications subject to change without notice. Panel Mount Datasheet DANGER / PELIGRO / DANGER /GEFAHR / PERICOLO / HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. * Disconnect all power before installing or working with this equipment. * Verify all connections and replace all covers before turning on power. Failure to follow these instructions will result in death or serious injury. RIESGO DE DESCARGA ELECTRICA O EXPLOSION. * Desconectar todos los suministros de energia a este equipo antes de trabajar con este equipo. * Verificar todas las conexiones y colocar todas las tapas antes de energizer el equipo. El incumplimiento de estas instrucciones puede provocar la muerte o lesiones serias. RISQUE DE DESCHARGE ELECTRIQUE OU EXPLOSION * Eteindre toutes les sources d'energie de cet appareil avant de travailler dessus de cet appareil * Verifier tous connections, et remettre tous couverts en olace avant de mettre sous De non-suivi de ces instructions provoquera la mort ou des lesions serieuses serieuses. GEFAHR EINES ELEKTRISCHE N SCHLAGES ODER EINER EXPLOSION. * Stellen Sie jeglichen Strom ab, der dieses Gerat versorgt, bevor Sie an dem Gerat Arbeiten durchfuhren * Vor dem Drehen auf Energie alle Anschlusse uberprufen und alle Abdeckungen ersetzen. Unterlassung dieser Anweisungen konnen zum Tode oder zu schweren Verletzungen fuhren. RISCHIO DI SCOSSA ELETTRICA O DELL'ESPLOSIONE. * Spenga tutta l'alimentazione che fornisce questa apparecchiatura prima di lavorare a questa apparecchiatura * * Verificare tutti i collegamenti e sostituire tutte le coperture prima dell'accensione L'omissione di queste istruzioni provochera la morte o lesioni serie WARNING / AVERTISSEMENT / WARNUNG /ADVERTENCIA / AVVERTENZA / RISK OF MATERIAL DAMAGE AND HOT ENCLOSURE RISQUE DE DOMMAGE MATERIEL ET DE SURCHAUFFE DU BOITIER GEFAHR VON MATERIALSCHADEN UND GEHAUSEERHITZUNG * The product's side panels may be hot, allow the product to cool before touching. * Follow proper mounting instructions including torque values. * Do not allow liquids or foreign objects to enter this product. * Les panneaux lateraux du produit peuvent etre chauds. Laisser le produit refroidir avant de le toucher. * Respecter les consignes de montage, et notamment les couples de serrage. * Ne pas laisser penetrer de liquide ni de corps etrangers a l'interieur du produit. * Die Seitenwande konnen hei sein. Lassen Sie das Produkt abkuhlen, bevor Sie es beruhren. * Beachten Sie die Montageanweisungen, * Fuhren Sie keine Flussigkeiten oder Fremdkorper in das Produkt ein. Le non-respect de cette directive peut entrainer, Failure to follow these instructions can result in des lesions corporelles graves ou des serious injury, or equipment damage. dommages materiels. Die Nichtbeachtung dieser Anweisung kann Korperverletzung oder Materialschaden zur Folge haben. RIESGO DE DANOS MATERIALES Y DE SOBRECALENTAMIENTO DE LA UNIDAD RISCHIO DI DANNI MATERIALI E D'INVOLUCRO CALDO * Los paneles laterales del producto pueden estar calientes. Esperar que el producto se enfrie antes de tocarlo. * Respetar las instrucciones de montaje, y en particular los pares de apretado. * No dejar que penetren liquidos o cuerpos extranos en el producto. * I pannelli laterali dell'apparecchio possono scottare; lasciar quindi raffreddare il prodotto prima di toccarlo. * Seguire le istruzioni di montaggio corrette. * Non far entrare liquidi o oggetti estranei in questo apparecchio. Si no se respetan estas precauciones pueden producirse graves lesiones, danos materiales. La mancata osservanza di questa precauzione puo causare gravi rischi per l'incolumita personale o danni alle apparecchiature. Do not forget to visit us at: www.crydom.com Copyright (c) 2017 Crydom Inc. Specifications subject to change without notice. * * * Panel Mount Datasheet ANNEX - ENVIRONMENTAL INFORMATION The environmental information disclosed in this annex including the EIP Pollution logo are in compliance with People's Republic of China Electronic Industry Standard SJ/T11364 - 2006, Marking for Control of Pollution Caused by Electronic Information Products. Part Name Toxic or hazardous Substance and Elements Lead (Pb) Mercury (Hg) Cadmium (Cd) Hexavalent Chromium (Cr (VI)) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) Semiconductor die Solder - SJ/T11364 - 2006, (Pb) (Hg) (Cd) (Cr (VI)) 50 Do not forget to visit us at: www.crydom.com Copyright (c) 2017 Crydom Inc. Specifications subject to change without notice. (PBB) (PBDE)