200A
PHASE CONTROL THYRISTORS Stud Version
ST180S SERIES
Bulletin I25165/B
Features
Center amplifying gate
Hermetic metal case with ceramic insulator
(Also available with glass-metal seal up to 1200V)
International standard case TO-209AB (TO-93)
Threaded studs UNF 3/4 - 16UNF2A or ISO M16x1.5
Compression Bonded Encapsulation for heavy duty
operations such as severe thermal cycling
Typical Applications
DC motor controls
Controlled DC power supplies
AC controllers
IT(AV) 200 A
@ TC85 °C
IT(RMS) 314 A
ITSM @ 50Hz 5000 A
@ 60Hz 5230 A
I2t@ 50Hz 125 KA2s
@ 60Hz 114 KA2s
VDRM/VRRM 400 to 2000 V
tqtypical 100 µs
TJ- 40 to 125 °C
Parameters ST180S Units
Major Ratings and Characteristics
case style
TO-209AB (TO-93)
Next Data SheetIndex
Previous Datasheet
To Order
ST180S Series
2222222222222
12
ELECTRICAL SPECIFICATIONS
Voltage Ratings
Voltage VDRM/VRRM, max. repetitive VRSM , maximum non- IDRM/IRRM max.
Type number Code peak and off-state voltage repetitive peak voltage @ TJ = TJ max
V V mA
04 400 500
08 800 900
12 1200 1300
16 1600 1700
18 1800 1900
20 2000 2100
ST180S 30
IT(AV) Max. average on-state current 200 A180° conduction, half sine wave
@ Case temperature 85 °C
IT(RMS) Max. RMS on-state current 314 ADC @ 76°C case temperature
ITSM Max. peak, one-cycle 5000 t = 10ms No voltage
non-repetitive surge current 5230 t = 8.3ms reapplied
4200 t = 10ms100% VRRM
4400 t = 8.3ms reapplied Sinusoidal half wave,
I2tMaximum I2t for fusing 125 t = 10ms No voltage Initial TJ = TJ max.
114 t = 8.3ms reapplied
88 t = 10ms 100% VRRM
81 t = 8.3ms reapplied
I2√tMaximum I2√t for fusing 1250 KA2√st = 0.1 to 10ms, no voltage reapplied
VT(TO)1 Low level value of threshold
voltage
VT(TO)2High level value of threshold
voltage
rt1 Low level value of on-state
slope resistance
rt2 High level value of on-state
slope resistance
VTM Max. on-state voltage 1.75 VIpk= 570A, TJ = 125°C, tp = 10ms sine pulse
IHMaximum holding current 600
ILMax. (typical) latching current 1000 (300)
1.08 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max.
1.18 (16.7% x π x IT(AV) < I < π x IT(AV)), TJ = TJ max.
1.14 (I > π x IT(AV)),TJ = TJ max.
Parameter ST180S Units Conditions
1.14 (I > π x IT(AV)),TJ = TJ max.
On-state Conduction
KA2s
V
mΩ
mA TJ = TJ max, anode supply 12V resistive load
A
di/dt Max. non-repetitive rate of rise Gate drive 20V, 20Ω, tr ≤ 1µs
of turned-on current TJ = TJ max, anode voltage ≤ 80% VDRM
Gate current 1A, dig/dt = 1A/µs
Vd = 0.67% VDRM, TJ = 25°C
ITM = 300A, TJ = TJ max, di/dt = 20A/µs, VR = 50V
dv/dt
=
20V/µs
, Gate 0V 100Ω,
tp
= 500µs
Parameter ST180S Units Conditions
tdTypical delay time 1.0
Switching
tqTypical turn-off time 100 µs
1000 A/µs
To Order
Next Data SheetIndex
Previous Datasheet
ST180S Series
23
dv/dt Maximum critical rate of rise of
off-state voltage
IDRM Max. peak reverse and off-state
IRRM leakage current
Blocking
500 V/µs TJ = TJ max linear to 80% rated VDRM
Parameter ST180S Units Conditions
30 mA TJ = TJ max, rated VDRM/VRRM applied
PGM Maximum peak gate power 10 TJ = TJ max, tp ≤ 5ms
PG(AV) Maximum average gate power 2.0 TJ = TJ max, f = 50Hz, d% = 50
IGM Max. peak positive gate current 3.0 ATJ = TJ max, tp ≤ 5ms
+VGM Maximum peak positive
gate voltage
-VGM Maximum peak negative
gate voltage
IGT DC gate current required TJ = - 40°C
to trigger mA TJ = 25°C
TJ = 125°C
VGTDC gate voltage required TJ = - 40°C
to trigger VTJ = 25°C
TJ = 125°C
IGD DC gate current not to trigger 10 mA
Parameter ST180S Units Conditions
20
5.0
Triggering
VGD DC gate voltage not to trigger 0.25 VTJ = TJ max
TYP. MAX.
180 -
90 150
40 -
2.9 -
1.8 3.0
1.2 -
Max. gate current/ voltage not to
trigger is the max. value which
will not trigger any unit with rated
VDRM anode-to-cathode applied
Max. required gate trigger/ cur-
rent/ voltage are the lowest value
which will trigger all units 12V
anode-to-cathode applied
W
VTJ = TJ max, tp ≤ 5ms
TJMax. operating temperature range -40 to 125
Tstg Max. storage temperature range -40 to 150
RthJC Max. thermal resistance,
junction to case
RthCS Max. thermal resistance,
case to heatsink
TMounting torque, ± 10% 31
(275)
24.5
(210)
wt Approximate weight 280 g
Case style TO - 209AB (TO-93) See Outline Table
Parameter ST180S Units Conditions
0.105 DC operation
0.04 Mounting surface, smooth, flat and greased
Thermal and Mechanical Specification
°C
K/W
Nm
(lbf-in) Lubricated threads
Non lubricated threads
To Order
Next Data SheetIndex
Previous Datasheet
ST180S Series
2222222222222
12
∆RthJC Conduction
(The following table shows the increment of thermal resistence RthJC when devices operate at different conduction angles than DC)
180° 0.015 0.012 TJ = TJ max.
120°0.019 0.020
90°0.025 0.027 K/W
60°0.036 0.037
30° 0.060 0.060
Conduction angle Sinusoidal conduction Rectangular conduction Units Conditions
Ordering Information Table
51 234
ST 18 0 S20 P0
7
68 9
Device Code
1-Thyristor
2-Essential part number
3-0 = Converter grade
4-S = Compression bonding Stud
5-Voltage code: Code x 100 = VRRM (See Voltage Rating Table)
6-P = Stud base 16UNF threads
M = Stud base metric threads (M16 x 1.5)
7-0 = Eyelet terminals (Gate and Auxiliary Cathode Leads)
1 = Fast - on terminals (Gate and Auxiliary Cathode Leads)
2 = Flag terminals (For Cathode and Gate Terminals)
8-V = Glass-metal seal (only up to 1200V)
None = Ceramic housing (over 1200V)
9-Critical dv/dt: None = 500V/µsec (Standard value)
L= 1000V/µsec (Special selection)
To Order
Next Data SheetIndex
Previous Datasheet
ST180S Series
23
Fast-on Terminals
Case Style TO-209AB (TO-93)
All dimensions in millimeters (inches)
Outline Table
2
WHITE SHRINK
RED SHRINK
RED CATHODE
RED SILICON RUBBER
+I
210 (8.26) 10 (0.39)
C.S. 0.4mm
(0.0006 s.i.)
MAX.
90 (3.54) MIN.
4.3 (0.17) DIA.
19 (0.75) MAX.
38.5 (1.52)
MAX.
16 (0.63) M AX.
8.5 (0.33) DIA.
+
-
GLASS METAL SEAL
28.5 (1.12) MAX. DIA.
220 (8.66) 10 (0.39)
* FOR METRIC DEVICE : M16 x 1.5 - LENGHT 21 (0.83) MAX.
SW 32
C.S. 25mm 2
(0.039 s.i.)
FLEXIBLE LEAD
4 (0.16) MAX.
22 (0.86) MIN.
35 (1.38) MAX.
3/4"-16UNF-2A *
27.5 (1.08)
9.5 (0.37) MIN.
WHITE GATE
2
WHITE SHRINK
RED SHRINK
RED CATHODE
RED SILICON RUBBER
+I
210 (8.26) 10 (0.39)
C.S. 0.4mm
(0.0006 s.i.)
38.5 (1 .52)
MAX.
+
-
220 (8.66) 10 (0.39)
CERAMIC HOUSING
90 (3.54) M IN.
4.3 (0.17) DIA.
19 (0.75) MAX.
8.5 (0.33) DIA.
* FOR METRIC DEVICE : M16 x 1.5 - LENGHT 21 (0.83) MAX.
C.S. 25mm 2
(0.039 s.i.)
FLEXIBLE LEAD
4 (0.16) MAX.
22 (0.86) MIN.
MAX.
35 (1.38) MAX.
3/4"-16UNF-2A *
27.5 (1.08)
SW 32
27.5 (1.08) MAX. DIA.
WHITE GATE
9.5 (0.37) MIN.
16 (0.63) MAX.
AMP. 280000-1
REF-250
To Order
Next Data SheetIndex
Previous Datasheet
ST180S Series
2222222222222
12
Outline Table
Case Style TO-209AB (TO-93) Flag
All dimensions in millimeters (inches)
GLASS-METAL SEAL
27 .5 (1 .08) MAX . 38.5 (1.5 2) M A X .
3 (0.12)
80 (3 .1 5) MAX .
DIA. 28.5 (1.12) MAX.
FLAG TERMINALS
1.5 (0.06) DIA.
SW 32
22 (0.89)
DIA. 6.5 (0.25)
13 (0.51 )
14 (0.55)
16 (0.63 ) M AX .
3/4"-16UNF-2A*
*FOR METRIC DEVICE. M16 X 1.5 - LENGHT 21 (0.83) MAX.
CERAMIC HOUSING
27 .5 (1 .08) M A X . 38 .5 (1.52 ) M A X .
3 (0.12)
8 0 (3.15 ) M A X.
DIA. 27.5 (1.08) MAX.
1 6 (0.63) M A X.
FLAG TERMINALS
1.5 (0.06) DIA.
SW 32
22 (0.89)
DIA. 6.5 (0.25)
13 (0.5 1)
14 (0.55)
*FOR METRIC DEVICE. M16 X 1.5 - LENGHT 21 (0.83) MAX.
3/4"-16UNF-2A*
To Order
Next Data SheetIndex
Previous Datasheet
