Previous Datasheet Index Next Data Sheet DISCRETE POWER DIODES and THYRISTORS DATA BOOK To Order Previous Datasheet Index Next Data Sheet Bulletin I25165/B ST180S SERIES PHASE CONTROL THYRISTORS Stud Version Features 200A Center amplifying gate Hermetic metal case with ceramic insulator (Also available with glass-metal seal up to 1200V) International standard case TO-209AB (TO-93) Threaded studs UNF 3/4 - 16UNF2A or ISO M16x1.5 Compression Bonded Encapsulation for heavy duty operations such as severe thermal cycling Typical Applications DC motor controls Controlled DC power supplies AC controllers Major Ratings and Characteristics Parameters ST180S Units 200 A 85 C 314 A @ 50Hz 5000 A @ 60Hz 5230 A @ 50Hz 125 KA2s @ 60Hz 114 KA2s 400 to 2000 V 100 s - 40 to 125 C IT(AV) @ TC IT(RMS) ITSM I 2t V DRM /V RRM tq TJ typical To Order case style TO-209AB (TO-93) Previous Datasheet ST180S Series Index Next Data Sheet ELECTRICAL SPECIFICATIONS Voltage Ratings Type number Voltage Code ST180S V DRM /V RRM , max. repetitive peak and off-state voltage V VRSM , maximum nonrepetitive peak voltage V 04 400 500 08 800 900 12 1200 1300 16 1600 1700 18 1800 1900 20 2000 2100 I DRM /I RRM max. @ TJ = TJ max mA 30 On-state Conduction Parameter I T(AV) ST180S Units Conditions Max. average on-state current 200 A @ Case temperature 85 C I T(RMS) Max. RMS on-state current 314 A I TSM Max. peak, one-cycle 5000 non-repetitive surge current 5230 Maximum I2t for fusing No voltage t = 8.3ms reapplied t = 10ms 100% VRRM 4400 t = 8.3ms reapplied Sinusoidal half wave, 125 t = 10ms No voltage Initial TJ = TJ max. t = 8.3ms reapplied t = 10ms 100% VRRM t = 8.3ms reapplied 114 A KA2s 88 81 2 I t 2 Maximum I t for fusing 1250 V T(TO)1 Low level value of threshold 2 KA s V V T(TO)2 High level value of threshold 1.14 (I > x IT(AV)),TJ = TJ max. 1.18 (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. voltage r t1 Low level value of on-state slope resistance r t2 t = 0.1 to 10ms, no voltage reapplied (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. 1.08 voltage 12 DC @ 76C case temperature t = 10ms 4200 I 2t 180 conduction, half sine wave m High level value of on-state (I > x IT(AV)),TJ = TJ max. 1.14 slope resistance V TM Max. on-state voltage 1.75 IH Maximum holding current 600 IL Max. (typical) latching current 2222222222222 V Ipk= 570A, TJ = 125C, tp = 10ms sine pulse mA TJ = TJ max, anode supply 12V resistive load 1000 (300) Switching Parameter di/dt ST180S Max. non-repetitive rate of rise of turned-on current td Typical delay time 1000 Units Conditions A/s 1.0 s tq Typical turn-off time To Order 100 Gate drive 20V, 20, tr 1s TJ = TJ max, anode voltage 80% VDRM Gate current 1A, di g /dt = 1A/s Vd = 0.67% VDRM, TJ = 25C ITM = 300A, TJ = TJ max, di/dt = 20A/s, VR = 50V dv/dt = 20V/s, Gate 0V 100, tp = 500s Previous Datasheet Index Fig. 1 - Current Ratings Characteristics Next Data Sheet ST180S Series Fig. 2 - Current Ratings Characteristics Fig. 3 - On-state Power Loss Characteristics To Order Previous Datasheet ST180S Series Index Fig. 5 - Maximum Non-Repetitive Surge Current Next Data Sheet Fig. 6 - Maximum Non-Repetitive Surge Current Fig. 7 - On-state Voltage Drop Characteristics Fig. 8 - Thermal Impedance Z thJC Characteristic To Order Previous Datasheet Index Fig. 9 - Gate Characteristics To Order Next Data Sheet ST180S Series Previous Datasheet Index Next Data Sheet ST180S Series Blocking Parameter ST180S Units Conditions dv/dt Maximum critical rate of rise of off-state voltage 500 V/s TJ = TJ max linear to 80% rated VDRM IDRM IRRM Max. peak reverse and off-state leakage current 30 mA TJ = TJ max, rated V DRM/V RRM applied Triggering Parameter PGM ST180S Maximum peak gate power 2.0 IGM Max. peak positive gate current 3.0 +VGM Maximum peak positive Maximum peak negative A TJ = TJ max, t p 5ms V TJ = TJ max, tp 5ms 5.0 gate voltage VGT TJ = TJ max, t p 5ms TJ = TJ max, f = 50Hz, d% = 50 20 gate voltage IGT W 10 PG(AV) Maximum average gate power -VGM Units Conditions TYP. MAX. DC gate current required 180 - to trigger 90 150 40 - TJ = 125C DC gate voltage required 2.9 - TJ = - 40C to trigger 1.8 3.0 1.2 - TJ = - 40C mA V TJ = 25C 23 Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied TJ = 25C TJ = 125C IGD DC gate current not to trigger 10 mA VGD DC gate voltage not to trigger 0.25 V TJ = TJ max Max. gate current/ voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Thermal and Mechanical Specification Parameter ST180S TJ Max. operating temperature range -40 to 125 Tstg Max. storage temperature range -40 to 150 RthJC Max. thermal resistance, junction to case RthCS Max. thermal resistance, case to heatsink T Mounting torque, 10% Units Conditions C 0.105 DC operation K/W 0.04 Mounting surface, smooth, flat and greased 31 (275) 24.5 Non lubricated threads Nm (lbf-in) Lubricated threads (210) wt Approximate weight Case style 280 g TO - 209AB (TO-93) See Outline Table To Order Previous Datasheet ST180S Series Index Next Data Sheet RthJC Conduction (The following table shows the increment of thermal resistence RthJC when devices operate at different conduction angles than DC) Conduction angle Sinusoidal conduction Rectangular conduction Units 180 0.015 0.012 120 0.019 0.020 90 0.025 0.027 60 0.036 0.037 30 0.060 0.060 Conditions TJ = TJ max. K/W Ordering Information Table 12 Device Code ST 18 0 S 20 P 0 1 2 3 4 5 6 7 1 - Thyristor 2 - Essential part number 3 - 0 = Converter grade 4 - S = Compression bonding Stud 5 - Voltage code: Code x 100 = VRRM (See Voltage Rating Table) 6 - P = Stud base 16UNF threads 8 9 M = Stud base metric threads (M16 x 1.5) 7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Leads) 1 = Fast - on terminals (Gate and Auxiliary Cathode Leads) 2 = Flag terminals (For Cathode and Gate Terminals) 8 - V = Glass-metal seal (only up to 1200V) None = Ceramic housing (over 1200V) 9 - Critical dv/dt: None = 500V/sec (Standard value) L = 1000V/sec (Special selection) To Order 2222222222222 Previous Datasheet Index Next Data Sheet ST180S Series Outline Table GLASS METAL SEAL 19 (0.75) MAX. 37 )M IN . 4 (0.16) MAX. 8.5 (0.33) DIA. C.S. 25mm 2 (0.039 s.i.) (0 . 22 FLEXIBLE LEAD 86 )M IN . 9 .5 ( 0. 4.3 (0.17) DIA. 10 (0.3 9) RED SILICON RUBBER C.S. 0.4mm (0.0006 s.i.) RED CATHODE AMP. 280000-1 REF-250 WHITE GATE 220 (8.66) RED SHRINK +10 - (0.39) M AX . 28.5 (1.12) MAX. DIA. 27.5 (1 .0 8) 16 (0.63) M AX. MA X . WHITE SHRINK SW 32 23 3/4"-16UNF-2A * 35 (1.38) MAX. Case Style TO-209AB (TO-93) All dimensions in millimeters (inches) * FOR METRIC DEVICE : M16 x 1.5 - LENGHT 21 (0.83) MAX. CERAMIC HOUSING 19 (0.75) MAX. . 4 (0.16) MAX. )M IN 8.5 (0.33) DIA. C.S. 25mm RED SILICON RUBBER C.S. 0.4mm 1 0 ( 0 .39 ) 2 (0.039 s.i.) RED CATHODE 2 (0.0006 s.i.) WHITE GATE 220 (8.66) +- (0.39) 10 WHITE SHRINK MA X. 27.5 (1.08) MAX. DIA. 27.5 ( 1.08) 16 (0.6 3) M A X. M AX . RED SHRINK 38 .5 (1 .52 ) 90 (3.5 4) M IN . +I SW 32 3/4"-16UNF-2A * 35 (1.38) MAX. * FOR METRIC DEVICE : M16 x 1.5 - LENGHT 21 (0.83) MAX. To Order 22 FLEXIBLE LEAD (0 . 86 )M IN . 9 .5 (0 .37 4.3 (0.17) DIA. 2 10 (8.2 6) 38 .5 ( 1.52) 90 (3 .54) M IN . +I 210 (8.2 6) Fast-on Terminals 2 Previous Datasheet ST180S Series Index Next Data Sheet Outline Table GLASS-METAL SEAL 22 (0.89) FLAG TERMINALS 14 (0.55) DIA. 28.5 (1.12) MAX. 1 6 (0.63 ) M A X . SW 32 12 3/4"-16UNF-2A* *FOR METRIC DEVICE. M16 X 1.5 - LENGHT 21 (0.83) MAX. Case Style TO-209AB (TO-93) Flag All dimensions in millimeters (inches) 3 (0.12) CERAMIC HOUSING 22 (0.89) FLAG TERMINALS DIA. 6.5 (0.25) 1 3 ( 0 .5 1 ) 14 (0.55) DIA. 27.5 (1.08) MAX. 1 6 (0 . 63 ) M A X . 3 8 .5 (1 . 52 ) M A X . 1.5 (0.06) DIA. 2 7 .5 (1 .0 8 ) M A X . 8 0 ( 3 .15 ) M A X . 3 8.5 (1.5 2) M A X . 1.5 (0.06) DIA. 27 .5 (1 .0 8) M A X . 80 (3 .1 5) M A X . 1 3 (0 .51 ) DIA. 6.5 (0.25) 2222222222222 SW 32 3/4"-16UNF-2A* *FOR METRIC DEVICE. M16 X 1.5 - LENGHT 21 (0.83) MAX. 3 (0.12) To Order