HRF-SW1030 SP6T Absorptive RF Switch DC to 2.5GHz Operation The Honeywell HRF-SW1030 is a high performance single pole six throw (SP6T) absorptive RF switch ideal for use in wireless basestation and handset applications that require minimum power and minimum insertion loss. The HRF-SW1030 is manufactured with Honeywell's patented Silicon On Insulator (SOI) CMOS technology, which provides the performance of GaAs with the economy and integration capabilities of conventional CMOS technology. These switches are DC coupled to improve lower operating frequency, frequency response and reduce the number of DC bias points required. HRF-SW1030 in VQFN Package FEATURES Typical High Isolation Of > 42 dB @ 2 GHz Typical Low Insertion Loss Of 1.6 dB @ 1 GHz Integrated CMOS Control Logic DC-coupled, bi-directional RF Path Single Positive Supply Voltage Ultra Small VQFN Packaging Impedance matched for 50 Ohm systems Lead-free, RoHS compliant and halogen-free RF ELECTRICAL SPECIFICATIONS @ + 25oC Results @ VDD = 5.0 +/- 10%, VSS = 0 unless otherwise stated, Z0 = 50 Ohms Contact Honeywell for relative performance at other supply configurations Parameter Test Condition Frequency Insertion Loss 1.0 GHz 2.0 GHz 2.5 GHz Isolation 1.0 GHz 2.0 GHz 3.0 GHz Return Loss Minimum Typical Maximum Units 1.6 2.1 2.4 2.5 3.3 3.8 dB dB dB 36 30 27 50 42 40 dB dB dB -10 -15 dB VSS =Gnd VSS = -5V 1.0 GHz 1.0 GHz 16 25 dBm dBm Input IP3 Two-Tone Inputs, + 5 dBm VSS = Gnd VSS = -5V 2.0 GHz 2.0 GHz 33 35 dBm dBm Trise, Tfall Ton, Toff 10% To 90% 50% Cntl To 90% / 10% RF 10 20 ns ns Input P1dB HRF-SW1030 DC ELECTRICAL SPECIFICATIONS @ + 25C Parameter Minimum Typical 1 VDD 3.3 5.0 VSS -5.0 IDD <5 CMOS Logic Level (0) 0 CMOS Logic Level (1) VDD - 0.8 Input Leakage Current Note 1 - Performance curves are for VDD = +5.0 +/- 10% Maximum 5.5 Units V V uA V V uA 35 0.8 VDD 10 ABSOLUTE MAXIMUM RATINGS1 Parameter Absolute Maximum Units VDD +6.0 V VSS -5.5 V Vin Digital Logic 0 -0.6 V Vin Digital Logic 1 VDD + 0.6 V Input Power > 35 dBm 2 ESD Voltage 400 V O Moisture Sensitivity Level Level 3 @ 260 C Operating Temperature Range -40 to +85 C Storage Temperature Range -65 to +125 C Note 1 - Operation of this device beyond any of these parameters may cause permanent damage. Note 2 - Although the HRF-SW1030 contains ESD protection circuitry on all digital inputs, precautions should be taken to ensure that the Absolute Maximum Ratings are not exceeded. Latch-Up: Unlike conventional CMOS digital switches, Honeywell's HRF-SW1030 is immune to latch-up. TRUTH TABLE C2 C1 C0 RF Output 1 RF Output 2 RF Output 3 RF Output 4 0 0 1 RFINPUT 0 1 0 RFINPUT 0 1 1 RFINPUT 1 0 0 RFINPUT 1 0 1 1 1 0 "0" = CMOS Low, "1" = CMOS High Note: For codes 000 and 111 all outputs are in the terminated isolation state. RF Output 5 RF Output 6 RFINPUT RFINPUT PIN CONFIGURATIONS Pin Function Pin Function 1 2 3 4 5 6 GROUND GROUND RFOUTPUT5 GROUND GROUND RFOUTPUT4 7 8 9 10 11 12 VDD C2 C1 C0 VSS RFOUTPUT3 13 14 15 16 17 18 GROUND GROUND RFOUTPUT2 GROUND GROUND RFOUTPUT1 Pin Function 19 20 21 22 23 24 GROUND GROUND RFINPUT GROUND GROUND RFOUTPUT6 Note: Bottom ground plate must be grounded for proper RF performance. 2 www.honeywell.com/microwave HRF-SW1030 PERFORMANCE CURVES Insertion Loss Typical SW1030 Insertion Loss 0.0 -0.5 Insertion Loss (dB) -1.0 -1.5 -2.0 -2.5 -3.0 -3.5 -4.0 -4.5 0.0 0.5 1.0 1.5 2.0 2.5 Frequency (GHz) Isolation Typical SW1030 Isolation -25 -30 Isolation (dB) -35 -40 -45 -50 -55 -60 -65 -70 0 0.5 1 1.5 2 2.5 Frequency (GHz) www.honeywell.com/microwave 3 HRF-SW1030 PACKAGE OUTLINE DRAWING Notes 1. Pin 1 identifier can be a combination or a dot and/or chamfer. A chamfer is on the bottom ground plane. 2. Dimensions are in millimeters. HALOGEN-FREE MATERIAL SET O The -FL switches have a halogen-free material set that can withstand a maximum soldering temperature of 260 C. LEAD FINISH The package leads are Nickel Palladium with a Gold and Silver flash (NiPdAu+Ag). The configuration being manufactured and delivered today is lead-free and RoHS compliant. Plating thicknesses are listed below in microns (um). Ni = 0.254 um min Pd = 0.00254 um min Au+Ag = 0.00508 um min Au Composition = 30% min to 70% max LEAD FREE QFN SURFACE MOUNT APPLICATION Please see Application Note AN310a for assembly process recommendations. The maximum soldering temperature of o the - FL is 260 C. Application Notes can be found at our website: www.honeywell.com/microwave CIRCUIT APPLICATION INFORMATION These switches require a DC reference to ground. They may not operate properly when AC coupled on both the RF input and output without a DC ground reference provided as part of the circuit. See Application Note AN311. 4 www.honeywell.com/microwave HRF-SW1030 EVALUATION CIRCUIT BOARD Honeywell's evaluation board provides an easy to use method of evaluating the RF performance of our switch. Simply connect power; DC and RF signals to be measuring switch performance in less than 10 minutes. RF Out6 RF Input HRF-SW1030 Honeywell RF Out1 RF Out5 HRF-SW1030 Evaluation Board Top View RF Out4 RF Out2 Gnd VDD C2 C1 C0 VSS Gnd HRF-SW1030 Evaluation Board RF Out3 EVALUATION CIRCUIT BOARD LAYOUT DESIGN DETAILS Item PCB Switch Chip Capacitor RF Connector DC Pin Description Impedance Matched Multi-Layer FR4 HRF-SW1030 Digital Switch Panasonic Model ECU-E1C103KBQ Capacitor, .01uf 0402 10% 16V Johnson Connectors Model 142-0701-801 SMA RF Coaxial Connector Mil-Max Model 800-10-064-10-001 Header Pins ORDERING INFORMATION Ordering Number HRF-SW1030-FL-TR HRF-SW1030-E Delivery Method Tape & Reel Evaluation Board Units Per Shipment 2500 Units per Reel One Board Per Box The new -FL switches replace and are electrically equivalent with the -GR switches. The -GR switches are obsolete. FIND OUT MORE For more information on Honeywell's Microwave Products visit us online at www.honeywellmicrowave.com or contact us at 800-323-8295 (763-954-2474 internationally). Honeywell reserves the right to make changes to improve reliability, function or design. Honeywell does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. Honeywell 12001 Highway 55 Plymouth, MN 55441 Tel: 800-323-8295 www.honeywell.com/microwave www.honeywellmicrowave.com Form #1030W May 2012 (c)2012 Honeywell International Inc. 5