HV9961 LED Driver with Average-Current Mode Constant-Current Control Features General Description * * * * * * Fast Average Current Control Programmable Constant Off-time Switching Linear Dimming Input PWM Dimming Input Output Short-circuit Protection with Skip Mode -40C to +125C Ambient Operating Temperature * Pin-compatible with HV9910B The HV9961 is an Average-Current mode constant-current control LED driver IC operating in a constant Off-time mode. Unlike the HV9910B, this control IC does not produce a peak-to-average error. This greatly improves accuracy as well as the line and load regulations of the LED current without any need for loop compensation or high-side current sensing. Its output LED current accuracy is 3%. Applications The HV9961 can be powered from an 8V-450V supply. It has a PWM dimming input that accepts an external control TTL-compatible signal. In addition, the output current can be programmed by an internal 275 mV reference or controlled externally through a 0V-1.5V linear dimming input. * * * * * * The IC is equipped with a current limit comparator for Hiccup mode output short-circuit protection. DC/DC or AC/DC LED Driver Applications LED Backlight Driver for LCD Displays General Purpose Constant-current Source LED Signage and Displays Architectural and Decorative LED Lighting LED Street Lighting The HV9961 is pin-to-pin compatible with HV9910B, and it can be used as a drop-in replacement for many applications to improve LED current accuracy and regulation. Package Types 16-lead SOIC (Top view) 8-lead SOIC (Top view) VIN 1 16 NC NC 2 15 NC NC 3 14 RT CS 4 13 LD VIN 1 8 RT GND 5 CS 2 7 LD NC 6 11 NC 6 VDD NC 7 10 NC GND 3 GATE 4 5 PWMD GATE 8 12 VDD 9 PWMD See Table 2-1 for pin information. 2017 Microchip Technology Inc. DS20005588A-page 1 HV9961 Functional Block Diagram Regulator VIN VDD UVLO POR 0.15/0.20V LD MIN (VLD * 0.185, 0.275V) GATE Auto-REF CS L/E Blanking Average Current Control Logic IN OUT PWMD R Q GND 0.44V S Q Hiccup CLK TOFF Timer HV9961 DS20005588A-page 2 400s i Current Mirror RT 2017 Microchip Technology Inc. HV9961 Typical Application Circuit LED Load 8V-450V 1 VIN 5 PWMD GATE 4 HV9961 6 VDD CS 2 7 LD RT 8 RT 2017 Microchip Technology Inc. GND 3 RCS Sets LED Current DS20005588A-page 3 HV9961 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings VIN to GND ............................................................................................................................................ -0.5V to +470V VDD to GND ............................................................................................................................................................ +12V CS, LD, PWMD, Gate, RT to GND.................................................................................................... -0.3V to VDD+0.3V Junction Temperature, TJ .................................................................................................................... -40C to +150C Storage Temperature, TS ..................................................................................................................... -65C to +150C Continuous Power Dissipation (TA = +25C): 8-lead SOIC ............................................................................................................................................ 650 mW 16-lead SOIC ........................................................................................................................................ 1000 mW Notice: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only, and functional operation of the device at those or any other conditions above those indicated in the operational sections of this specification is not intended. Exposure to maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS Electrical Specifications: TA = 25C, VIN = 12V, VLD = VDD, and VPWMD = VDD unless otherwise specified. Parameter Sym. Min. Typ. Max. Unit Input DC Supply Voltage Range VINDC 8 -- 450 V Shutdown Mode Supply Current IINSD -- 0.5 1 mA VDD 7.25 7.5 7.75 V Line Regulation of VDD VDD, line 0 -- 1 V Load Regulation of VDD VDD, load 0 -- 100 mV Conditions INPUT DC input voltage (Note 1 and Note 2) Pin PWMD connected to GND (Note 2) INTERNAL REGULATOR Internally Regulated Voltage VIN = 8V, IDD(EXT) = 0 mA, 500 pF at gate, RT = 226 k VIN = 8V-450V, IDD(EXT) = 0 mA, 500 pF at gate, RT = 226 k IDD(EXT) = 0 mA-1 mA, 500 pF at gate, RT = 226 k VDD Undervoltage Lockout Upper Threshold VDD Undervoltage Lockout Hysteresis VUVLO 6.45 6.7 6.95 V VUVLO -- 500 -- mV VIN falling Maximum Input Current (Limited by UVLO) IIN, MAX 3.5 1.5 -- -- -- -- mA VIN = 8V, TA = 25C (Note 3) VIN = 8V, TA = 125C (Note 3) -- 2.2 50 -- -- 100 0.8 -- 150 V V k VIN = 8V-450V (Note 2) VIN = 8V-450V (Note 2) VPWMD = 5V mV -- VLD = 1.5V VLD = 1.2V Offset = VCS- AV(LD) x VLD, VLD = 1.2V PWM DIMMING PWMD Input Low Voltage VPWMD(LO) PWMD Input High Voltage VPWMD(HI) PWMD Pull-down Resistance RPWMD AVERAGE-CURRENT SENSE LOGIC Current Sense Reference Voltage VCST LD-to-CS Voltage Ratio AV(LD) LD-to-CS Voltage Offset Note 1: 2: 3: AV x VLD(OFFSET) 268 275 286 0.182 0.185 0.188 0 -- 10 mV VIN rising (Note 2) Also limited by package power dissipation limit, whichever is lower Denotes specifications which apply over the full operating ambient temperature range of -40C < TA < +125C Specification is obtained by characterization and is not 100% tested. DS20005588A-page 4 2017 Microchip Technology Inc. HV9961 ELECTRICAL CHARACTERISTICS (CONTINUED) Electrical Specifications: TA = 25C, VIN = 12V, VLD = VDD, and VPWMD = VDD unless otherwise specified. Parameter CS Threshold Temperature Regulation LD Input Shutdown Threshold Voltage LD Input Enable Threshold Voltage Current Sense Blanking Interval Minimum On-time Maximum Steady-state Duty Cycle SHORT-CIRCUIT PROTECTION Hiccup Threshold Voltage Current Limit Delay CS-to-Gate Short-circuit Hiccup Time Minimum On-time (Short-circuit) TOFF TIMER Off-time Sym. Min. Typ. Max. Unit VCST(TEMP) -- -- 5 mV (Note 2) VLD(OFF) -- 150 -- mV VLD falling VLD(EN) TBLANK TON(MIN) -- 150 -- 200 -- -- -- 320 1000 mV ns ns DMAX 75 -- -- % VLD rising (Note 2) VCS = VCST + 30 mV Reduction in output LED current may occur beyond this duty cycle VCSH TDELAY THICCUP 410 -- 350 -- 440 -- 400 -- 470 150 550 430 mV ns s ns 32 8 40 10 48 12 s TON(MIN),SC TOFF Conditions VCS = VCSH + 30 mV VCS = VDD RT = 1 M RT = 226 k GATE DRIVER 0.165 -- -- A VGATE = 0V, VDD = 7.5V Gate Sourcing Current ISOURCE Gate Sinking Current ISINK 0.165 -- -- A VGATE = VDD, VDD = 7.5V Gate Output Rise Time tr -- 30 50 ns CGATE = 500 pF, VDD = 7.5V -- 30 50 ns CGATE = 500 pF, VDD = 7.5V Gate Output Fall Time tf Note 1: Also limited by package power dissipation limit, whichever is lower 2: Denotes specifications which apply over the full operating ambient temperature range of -40C < TA < +125C 3: Specification is obtained by characterization and is not 100% tested. TEMPERATURE SPECIFICATIONS Parameter Sym. Min. Typ. Max. Unit Operating Ambient Temperature TA -40 -- +125 C Maximum Junction Temperature TJ(MAX) -- -- +150 C TS -65 -- +150 C 8-lead SOIC JA -- 101 -- C/W 16-lead SOIC JA -- 83 -- C/W Conditions TEMPERATURE RANGES Storage Temperature PACKAGE THERMAL RESISTANCE 2017 Microchip Technology Inc. DS20005588A-page 5 HV9961 2.0 PIN DESCRIPTION The details on the pins of HV9961 are listed on Table 2-1. Refer to Package Types for the location of pins. TABLE 2-1: PIN FUNCTION TABLE Pin Number 8-lead SOIC 16-lead SOIC Pin Name Description This pin is the input of an 8V-450V linear regulator. This pin is the current sense pin used to sense the FET current with an external sense resistor. Ground return for all internal circuitry. This pin must be electrically connected to the ground of the power train. This pin is the output of gate driver for driving an external N-channel power MOSFET. This is the PWM dimming input of the IC. When this pin is pulled to GND, the gate driver is turned off. When the pin is pulled high, the gate driver operates normally. This is the power supply pin for all internal circuits. It must be bypassed with a low ESR capacitor to GND (at least 0.1 F). This pin is the linear dimming input, and it sets the current sense threshold as long as the voltage at this pin is less than 1.5V. If voltage at LD falls below 150 mV, the gate output is disabled. The gate signal recovers at 200 mV at LD. A resistor connected between this pin and GND programs the gate off-time. 1 1 VIN 2 4 CS 3 5 GND 4 8 Gate 5 9 PWMD 6 12 VDD 7 13 LD 8 14 RT -- 2, 3, 6, 7, 10, 11, 15 and16 NC DS20005588A-page 6 No connection 2017 Microchip Technology Inc. HV9961 3.0 APPLICATION INFORMATION 3.1 General Description 3.3 Average-Current Control Feedback and Output Short-circuit Protection Peak current control (as in HV9910B) is the simplest and the most economical way to regulate a buck converter's output current. However, it suffers accuracy and regulation problems that arise from peak-to-average current error, contributed by the current ripple in the output inductor and the propagation delay in the current sense comparator. The full inductor current signal is unavailable for direct switch current sensing across the sense resistor at the ground path in this low-side switch buck converter when the control switch is at the ground potential because the switch is turned off. While it is very simple to detect the peak current in the switch, controlling the average inductor current is usually implemented by level translating the sense signal from +VIN. Although this is practical for a relatively low-input voltage, VIN, this type of average-current control may become excessively complex and expensive in the offline AC or other high-voltage DC applications. The current through the switching Metal-oxide Semiconductor Field-effect Transistor (MOSFET) source is averaged and used to give constant-current feedback. This current is detected with a sense resistor at the CS pin. The feedback operates in a fast Open-loop mode. No compensation is required. Output current is programmed as seen in Equation 3-2. The HV9961 uses a proprietary control scheme that allows fast and accurate control of the average current in the buck inductor by sensing the switch current only. No compensation of the current control loop is required. The output LED current's response to PWMD input is similar to that of the HV9910B. The effect of inductor current ripple amplitude on this control scheme is insignificant. Therefore, the LED current is independent of the variation in inductance, switching frequency or output voltage. Constant off-time control of the buck converter is used for stability and improving the LED current regulation over a wide range of input voltages. Unlike HV9910B, the HV9961 does not support Constant Frequency mode. V LD 0.185 I LED = -----------------------------R CS 3.2 Off Timer The timing resistor connected between RT and GND determines the off-time of the gate driver. Wiring this resistor between RT and Gate as with HV9910B is no longer supported. Refer to Equation 3-1 for the computation of the gate output's off-time. EQUATION 3-1: R T k T OFF s = ------------------- + 0.3 25 within the range of 30 k RT 1 M EQUATION 3-2: 0.275V I LED = ----------------R CS When the voltage at the LD input VLD 1.5V If the voltage at the LD input is less than 1.5V, the output current is computed as specified in Equation 3-3. EQUATION 3-3: When the voltage at the LD input 0.2V VLD < 1.5V The above equations are only valid for continuous conduction of the output inductor. It is good design practice to choose the inductance of the inductor such that the peak-to-peak inductor current is 30% to 40% of the average DC full-load current. Hence, the recommended inductance can be calculated as shown in Equation 3-4. EQUATION 3-4: V O MAX T OFF L O = ----------------------------------------0.4 I O The duty-cycle range of the current control feedback is limited to D 0.75. A reduction in the LED current may occur when the desired LED string voltage VO is greater than 75% of the input voltage VIN of the HV9961 LED driver. Reducing the targeted output LED string voltage VO below VO(MIN) = VIN x DMIN, where DMIN = 1 s/(TOFF +1 s), may also result in the loss of regulation of the LED current. This condition, however, causes an increase in the LED current and can potentially trip the short-circuit protection comparator. The typical output characteristic of the HV9961 LED driver is shown in Figure 3-1. The corresponding HV9910B characteristic is given for the comparison. 2017 Microchip Technology Inc. DS20005588A-page 7 HV9961 LD Response Characteristics Output Characteristics 0.60 0.40 0.35 VIN = 170VDC 0.50 0.30 LED Current (A) LED Current (A) 0.55 0.45 0.40 HV9961 0.35 0.30 0 10 20 30 40 50 0.20 0.15 0.10 HV9910B 0.25 0.25 0.05 60 Output Voltage (V) 0 FIGURE 3-1: Typical Output Characteristic of an HV9961 LED Driver. The short-circuit protection comparator trips when the voltage at CS exceeds 0.44V. When this occurs, the short-circuit gate off-time THICCUP = 400 s is generated to prevent the staircasing of the inductor current and, potentially, its saturation due to insufficient output voltage. The typical short-circuit inductor current is shown in the waveform of Figure 3-2. 0.44V/RCS 400s FIGURE 3-2: Current. Short-circuit Inductor A leading-edge blanking delay is provided at CS to prevent false triggering of the current feedback and the short-circuit protection. 3.4 Linear Dimming When the voltage at LD falls below 1.5V, the internal 275 mV reference to the constant-current feedback becomes overridden by VLD x 0.185. As long as the current in the inductor remains continuous, the LED current is given by Equation 3-3. However, when VLD falls below 150 mV, the gate output becomes disabled. The gate signal recovers when VLD exceeds 200 mV. It is required in some applications to use the same brightness control signal input to shut off the lamp. The typical linear dimming response is shown in Figure 3-3. 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 LD (V) FIGURE 3-3: Typical Linear Dimming Response of an HV9961 LED Driver. The linear dimming input could also be used for "mixed-mode" dimming to expand the dimming ratio. In such case, a pulse-width modulated signal with an amplitude below 1.5V should be applied to LD. 3.5 Input Voltage Regulator The HV9961 can be powered directly from an 8 VDC-450 VDC supply through its VIN input. When this voltage is applied at the VIN pin, the HV9961 maintains a constant 7.5V level at VDD. This voltage can be used to power the IC and external circuitry connected to VDD within the rated maximum current or within the thermal ratings of the package, whichever limit is lower. The VDD pin must be bypassed by a low ESR capacitor to provide a low-impedance path for the high-frequency current of the gate output. The HV9961 can also be powered through the VDD pin directly with a voltage greater than the internally regulated 7.5V, but less than 12V. Despite the instantaneous voltage rating of 450V, continuous voltage at VIN is limited by the power dissipation in the package. For example, when HV9961 draws IIN = 2.5 mA from the VIN input, and the 8-pin SOIC package is used, the maximum continuous voltage at VIN is limited to the value shown in Equation 3-5. EQUATION 3-5: T J MAX - T A V IN MAX = -------------------------------R JA I IN = 396V Where: Ambient temperature: TA = 25C Maximum working junction temperature: TJ(MAX) = 125C Junction-to-ambient thermal resistance: R,JA = 101C/W DS20005588A-page 8 2017 Microchip Technology Inc. HV9961 In such cases, when it is needed to operate the HV9961 from a higher voltage, a resistor or a Zener diode can be added in series with the VIN input to divert some of the power loss from the HV9961. In the above example, using a 100V Zener diode will allow the circuit to work up to 490V. The input current drawn from the VIN pin is represented by Equation 3-6. EQUATION 3-6: I IN 1mA + Q G f S Where: fS = Switching frequency QG = Gate charge of the external FET (obtained from the manufacturer's data sheet) 3.6 Gate Output The gate output of the HV9961 is used to drive an external MOSFET. It is recommended that the gate charge QG of the external MOSFET be less than 25 nC for switching frequencies 100 kHz and less than 15 nC for switching frequencies >100 kHz. 3.7 PWM Dimming Due to the fast open-loop response of the average-current control loop of the HV9961, its PWM dimming performance nearly matches that of the HV9910B. The inductor current waveform comparison is shown in Figure 3-4. CH4 = Inductor Current CH3 = Inductor Current of HV9910B for comparison CH2 = VPWMD FIGURE 3-4: Typical PWM Dimming Response of an HV9961 LED Driver. The rising and falling edges are limited by the current slew rate in the inductor. The first switching cycle is terminated upon reaching the 275 mV or VLD x 0.185 level at CS. The circuit is further reaching its steady-state within 3-4 switching cycles regardless of the switching frequency. 2017 Microchip Technology Inc. DS20005588A-page 9 HV9961 4.0 PACKAGING INFORMATION 4.1 Package Marking Information 8-lead SOIC Example XXXXXXXX e3 YYWW NNN HV9961LG e3 1725 888 16-lead SOIC XXXXXXXXX e3 YYWWNNN Legend: XX...X Y YY WW NNN e3 * Note: DS20005588A-page 10 Example HV9961NG e3 1714789 Product Code or Customer-specific information Year code (last digit of calendar year) Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Alphanumeric traceability code Pb-free JEDEC(R) designator for Matte Tin (Sn) This package is Pb-free. The Pb-free JEDEC designator ( e3 ) can be found on the outer packaging for this package. In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line, thus limiting the number of available characters for product code or customer-specific information. Package may or not include the corporate logo. 2017 Microchip Technology Inc. HV9961 Note: For the most current package drawings, see the Microchip Packaging Specification at www.microchip.com/packaging. 2017 Microchip Technology Inc. DS20005588A-page 11 HV9961 16-Lead SOIC (Narrow Body) Package Outline (NG) 9.90x3.90mm body, 1.75mm height (max), 1.27mm pitch D 16 1 E1 E Note 1 (Index Area D/2 x E1/2) L2 1 L Top View View B View B A h A A2 h Seating Plane e A1 Seating Plane L1 Gauge Plane Note 1 b Side View View A-A A Note: For the most current package drawings, see the Microchip Packaging Specification at www.microchip.com/packaging. Note: 1. 7KLVFKDPIHUIHDWXUHLVRSWLRQDO,ILWLVQRWSUHVHQWWKHQD3LQLGHQWLHUPXVWEHORFDWHGLQWKHLQGH[DUHDLQGLFDWHG7KH3LQLGHQWLHUFDQEH DPROGHGPDUNLGHQWLHUDQHPEHGGHGPHWDOPDUNHURUDSULQWHGLQGLFDWRU Symbol A MIN Dimension (mm) 1.35* A1 0.10 A2 1.25 b 0.31 NOM - - - - MAX 1.75 0.25 1.65* 0.51 D 9.80* 9.90 E E1 e 5.80* 3.80* 6.00 3.90 10.00* 6.20* 4.00* h 0.25 1.27 BSC L L1 L2 0.40 0 1.04 0.25 REF BSC - - 0.50 1.27 O 5O - - 8O 15O JEDEC Registration MS-012, Variation AC, Issue E, Sept. 2005. 7KLVGLPHQVLRQLVQRWVSHFLHGLQWKH-('(&GUDZLQJ Drawings are not to scale. DS20005588A-page 12 2017 Microchip Technology Inc. HV9961 APPENDIX A: REVISION HISTORY Revision A (November 2017) * Converted Supertex Doc# DSFP-HV9961 to Microchip DS20005588A * Changed the package marking format * Changed the packaging quantity of the LG package from 2500/Reel to 3300/Reel * Changed the packaging quantity of the NG M901 media type from 1000/Reel to 2600/Reel * Changed the packaging quantity of the NG M934 media type from 2500/Reel to 2600/Reel * Made minor text changes throughout the document 2017 Microchip Technology Inc. DS20005588A-page 13 HV9961 PRODUCT IDENTIFICATION SYSTEM To order or obtain information, e.g., on pricing or delivery, contact your local Microchip representative or sales office. XX PART NO. Package Options Device Device: Packages: Environmental: Media Types: - HV9961 = X - Environmental X Examples: a) HV9961LG-G: LED Driver with AverageCurrent Mode ConstantCurrent Control, 8-lead SOIC, 3300/Reel b) HV9961NG-G: LED Driver with AverageCurrent Mode ConstantCurrent Control, 16-lead SOIC, 45/Tube c) HV9961NG-G-M901: LED Driver with AverageCurrent Mode ConstantCurrent Control, 16-lead SOIC, 2600/Reel d) HV9961NG-G-M934: LED Driver with AverageCurrent Mode ConstantCurrent Control, 16-lead SOIC, 2600/Reel Media Type LED Driver with Average-Current Mode Constant-Current Control LG = 8-lead SOIC NG = 16-lead SOIC G = Lead (Pb)-free/RoHS-compliant Package (blank) = 3300/Reel for an LG Package (blank) = 45/Tube for an NG Package M901 = 2600/Reel for an NG Package M934 = 2600/Reel for an NG Package Note: For Media Types M901 and M934, the base quantity for tape and reel was standardized to 2600/reel. Both options will result in the delivery of the same number of parts/reel. DS20005588A-page 14 2017 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights unless otherwise stated. Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. QUALITY MANAGEMENT SYSTEM CERTIFIED BY DNV Trademarks The Microchip name and logo, the Microchip logo, AnyRate, AVR, AVR logo, AVR Freaks, BeaconThings, BitCloud, CryptoMemory, CryptoRF, dsPIC, FlashFlex, flexPWR, Heldo, JukeBlox, KEELOQ, KEELOQ logo, Kleer, LANCheck, LINK MD, maXStylus, maXTouch, MediaLB, megaAVR, MOST, MOST logo, MPLAB, OptoLyzer, PIC, picoPower, PICSTART, PIC32 logo, Prochip Designer, QTouch, RightTouch, SAM-BA, SpyNIC, SST, SST Logo, SuperFlash, tinyAVR, UNI/O, and XMEGA are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. ClockWorks, The Embedded Control Solutions Company, EtherSynch, Hyper Speed Control, HyperLight Load, IntelliMOS, mTouch, Precision Edge, and Quiet-Wire are registered trademarks of Microchip Technology Incorporated in the U.S.A. Adjacent Key Suppression, AKS, Analog-for-the-Digital Age, Any Capacitor, AnyIn, AnyOut, BodyCom, chipKIT, chipKIT logo, CodeGuard, CryptoAuthentication, CryptoCompanion, CryptoController, dsPICDEM, dsPICDEM.net, Dynamic Average Matching, DAM, ECAN, EtherGREEN, In-Circuit Serial Programming, ICSP, Inter-Chip Connectivity, JitterBlocker, KleerNet, KleerNet logo, Mindi, MiWi, motorBench, MPASM, MPF, MPLAB Certified logo, MPLIB, MPLINK, MultiTRAK, NetDetach, Omniscient Code Generation, PICDEM, PICDEM.net, PICkit, PICtail, PureSilicon, QMatrix, RightTouch logo, REAL ICE, Ripple Blocker, SAM-ICE, Serial Quad I/O, SMART-I.S., SQI, SuperSwitcher, SuperSwitcher II, Total Endurance, TSHARC, USBCheck, VariSense, ViewSpan, WiperLock, Wireless DNA, and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. Silicon Storage Technology is a registered trademark of Microchip Technology Inc. in other countries. GestIC is a registered trademark of Microchip Technology Germany II GmbH & Co. KG, a subsidiary of Microchip Technology Inc., in other countries. All other trademarks mentioned herein are property of their respective companies. (c) 2017, Microchip Technology Incorporated, All Rights Reserved. ISBN: 978-1-5224-2317-1 == ISO/TS 16949 == 2017 Microchip Technology Inc. DS20005588A-page 15 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Australia - Sydney Tel: 61-2-9868-6733 India - Bangalore Tel: 91-80-3090-4444 China - Beijing Tel: 86-10-8569-7000 India - New Delhi Tel: 91-11-4160-8631 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 China - Chengdu Tel: 86-28-8665-5511 India - Pune Tel: 91-20-4121-0141 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 China - Chongqing Tel: 86-23-8980-9588 Japan - Osaka Tel: 81-6-6152-7160 Finland - Espoo Tel: 358-9-4520-820 China - Dongguan Tel: 86-769-8702-9880 Japan - Tokyo Tel: 81-3-6880- 3770 China - Guangzhou Tel: 86-20-8755-8029 Korea - Daegu Tel: 82-53-744-4301 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 China - Hangzhou Tel: 86-571-8792-8115 Korea - Seoul Tel: 82-2-554-7200 China - Hong Kong SAR Tel: 852-2943-5100 Malaysia - Kuala Lumpur Tel: 60-3-7651-7906 China - Nanjing Tel: 86-25-8473-2460 Malaysia - Penang Tel: 60-4-227-8870 China - Qingdao Tel: 86-532-8502-7355 Philippines - Manila Tel: 63-2-634-9065 China - Shanghai Tel: 86-21-3326-8000 Singapore Tel: 65-6334-8870 China - Shenyang Tel: 86-24-2334-2829 Taiwan - Hsin Chu Tel: 886-3-577-8366 China - Shenzhen Tel: 86-755-8864-2200 Taiwan - Kaohsiung Tel: 886-7-213-7830 Israel - Ra'anana Tel: 972-9-744-7705 China - Suzhou Tel: 86-186-6233-1526 Taiwan - Taipei Tel: 886-2-2508-8600 China - Wuhan Tel: 86-27-5980-5300 Thailand - Bangkok Tel: 66-2-694-1351 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 China - Xian Tel: 86-29-8833-7252 Vietnam - Ho Chi Minh Tel: 84-28-5448-2100 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Austin, TX Tel: 512-257-3370 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Novi, MI Tel: 248-848-4000 Houston, TX Tel: 281-894-5983 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Tel: 317-536-2380 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Tel: 951-273-7800 Raleigh, NC Tel: 919-844-7510 New York, NY Tel: 631-435-6000 San Jose, CA Tel: 408-735-9110 Tel: 408-436-4270 Canada - Toronto Tel: 905-695-1980 Fax: 905-695-2078 DS20005588A-page 16 China - Xiamen Tel: 86-592-2388138 China - Zhuhai Tel: 86-756-3210040 Germany - Garching Tel: 49-8931-9700 Germany - Haan Tel: 49-2129-3766400 Germany - Heilbronn Tel: 49-7131-67-3636 Germany - Karlsruhe Tel: 49-721-625370 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Germany - Rosenheim Tel: 49-8031-354-560 Italy - Padova Tel: 39-049-7625286 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 Norway - Trondheim Tel: 47-7289-7561 Poland - Warsaw Tel: 48-22-3325737 Romania - Bucharest Tel: 40-21-407-87-50 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 Sweden - Gothenberg Tel: 46-31-704-60-40 Sweden - Stockholm Tel: 46-8-5090-4654 UK - Wokingham Tel: 44-118-921-5800 Fax: 44-118-921-5820 2017 Microchip Technology Inc. 10/25/17